| // SPDX-License-Identifier: BSD-3-Clause |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| |
| &spmi_bus { |
| pm8226_0: pm8226@0 { |
| compatible = "qcom,pm8226", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pwrkey@800 { |
| compatible = "qcom,pm8941-pwrkey"; |
| reg = <0x800>; |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| }; |
| |
| smbb: charger@1000 { |
| compatible = "qcom,pm8226-charger"; |
| reg = <0x1000>; |
| interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "chg-done", |
| "chg-fast", |
| "chg-trkl", |
| "bat-temp-ok", |
| "bat-present", |
| "chg-gone", |
| "usb-valid", |
| "dc-valid"; |
| |
| chg_otg: otg-vbus { }; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>, <0x6100>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| pm8226_vadc: adc@3100 { |
| compatible = "qcom,spmi-vadc"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| adc-chan@7 { |
| reg = <VADC_VSYS>; |
| qcom,pre-scaling = <1 3>; |
| label = "vph_pwr"; |
| }; |
| adc-chan@8 { |
| reg = <VADC_DIE_TEMP>; |
| label = "die_temp"; |
| }; |
| adc-chan@9 { |
| reg = <VADC_REF_625MV>; |
| label = "ref_625mv"; |
| }; |
| adc-chan@a { |
| reg = <VADC_REF_1250MV>; |
| label = "ref_1250mv"; |
| }; |
| adc-chan@e { |
| reg = <VADC_GND_REF>; |
| }; |
| adc-chan@f { |
| reg = <VADC_VDD_VADC>; |
| }; |
| }; |
| |
| pm8226_mpps: mpps@a000 { |
| compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp"; |
| reg = <0xa000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pm8226_mpps 0 0 8>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pm8226_1: pm8226@1 { |
| compatible = "qcom,pm8226", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8226_spmi_regulators: pm8226-regulators { |
| compatible = "qcom,pm8226-regulators"; |
| }; |
| |
| pm8226_vib: vibrator@c000 { |
| compatible = "qcom,pm8916-vib"; |
| reg = <0xc000>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
