| # SPDX-License-Identifier: GPL-2.0 |
| # |
| # Copyright 2008 Openmoko, Inc. |
| # Simtec Electronics, Ben Dooks <ben@simtec.co.uk> |
| |
| menuconfig ARCH_S3C64XX |
| bool "Samsung S3C64XX (deprecated, see help)" |
| depends on ARCH_MULTI_V6 |
| select ARM_AMBA |
| select ARM_VIC |
| select CLKSRC_SAMSUNG_PWM |
| select COMMON_CLK_SAMSUNG |
| select GPIO_SAMSUNG if ATAGS |
| select GPIOLIB |
| select HAVE_TCM |
| select PLAT_SAMSUNG |
| select PM_GENERIC_DOMAINS if PM |
| select S3C_DEV_NAND if ATAGS |
| select S3C_GPIO_TRACK if ATAGS |
| select S3C2410_WATCHDOG |
| select SAMSUNG_ATAGS if ATAGS |
| select SAMSUNG_WAKEMASK if PM |
| select WATCHDOG |
| help |
| Samsung S3C64XX series based systems |
| |
| The platform is deprecated and scheduled for removal. Please reach to |
| the maintainers of the platform and linux-samsung-soc@vger.kernel.org if |
| you still use it. |
| Without such feedback, the platform will be removed after 2024. |
| |
| if ARCH_S3C64XX |
| |
| # Configuration options for the S3C6410 CPU |
| |
| config CPU_S3C6400 |
| bool |
| help |
| Enable S3C6400 CPU support |
| |
| config CPU_S3C6410 |
| bool |
| help |
| Enable S3C6410 CPU support |
| |
| config S3C64XX_PL080 |
| def_bool DMADEVICES |
| select AMBA_PL08X |
| |
| config S3C64XX_SETUP_SDHCI |
| bool |
| select S3C64XX_SETUP_SDHCI_GPIO |
| help |
| Internal configuration for default SDHCI setup for S3C6400 and |
| S3C6410 SoCs. |
| |
| config S3C64XX_DEV_ONENAND1 |
| bool |
| help |
| Compile in platform device definition for OneNAND1 controller |
| |
| config SAMSUNG_DEV_BACKLIGHT |
| bool |
| depends on SAMSUNG_DEV_PWM |
| help |
| Compile in platform device definition LCD backlight with PWM Timer |
| |
| # platform specific device setup |
| |
| config S3C64XX_SETUP_I2C0 |
| bool |
| default y |
| help |
| Common setup code for i2c bus 0. |
| |
| Note, currently since i2c0 is always compiled, this setup helper |
| is always compiled with it. |
| |
| config S3C64XX_SETUP_I2C1 |
| bool |
| help |
| Common setup code for i2c bus 1. |
| |
| config S3C64XX_SETUP_IDE |
| bool |
| help |
| Common setup code for S3C64XX IDE. |
| |
| config S3C64XX_SETUP_FB_24BPP |
| bool |
| help |
| Common setup code for S3C64XX with an 24bpp RGB display helper. |
| |
| config S3C64XX_SETUP_KEYPAD |
| bool |
| help |
| Common setup code for S3C64XX KEYPAD GPIO configurations |
| |
| config S3C64XX_SETUP_SDHCI_GPIO |
| bool |
| help |
| Common setup code for S3C64XX SDHCI GPIO configurations |
| |
| config S3C64XX_SETUP_SPI |
| bool |
| help |
| Common setup code for SPI GPIO configurations |
| |
| config S3C64XX_SETUP_USB_PHY |
| bool |
| help |
| Common setup code for USB PHY controller |
| |
| # S36400 Macchine support |
| |
| config MACH_SMDK6400 |
| bool "SMDK6400" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6400 |
| select S3C64XX_SETUP_SDHCI |
| select S3C_DEV_HSMMC1 |
| help |
| Machine support for the Samsung SMDK6400 |
| |
| # S3C6410 machine support |
| |
| config MACH_ANW6410 |
| bool "A&W6410" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C_DEV_FB |
| help |
| Machine support for the A&W6410 |
| |
| config MACH_MINI6410 |
| bool "MINI6410" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_SDHCI |
| select S3C_DEV_FB |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_NAND |
| select S3C_DEV_USB_HOST |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_TS |
| help |
| Machine support for the FriendlyARM MINI6410 |
| |
| config MACH_REAL6410 |
| bool "REAL6410" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_SDHCI |
| select S3C_DEV_FB |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_NAND |
| select S3C_DEV_USB_HOST |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_TS |
| help |
| Machine support for the CoreWind REAL6410 |
| |
| config MACH_SMDK6410 |
| bool "SMDK6410" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_I2C1 |
| select S3C64XX_SETUP_IDE |
| select S3C64XX_SETUP_KEYPAD |
| select S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_USB_PHY |
| select S3C_DEV_FB |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_I2C1 |
| select S3C_DEV_RTC |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_USB_HSOTG |
| select S3C_DEV_WDT |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_BACKLIGHT |
| select SAMSUNG_DEV_IDE |
| select SAMSUNG_DEV_KEYPAD |
| select SAMSUNG_DEV_PWM |
| select SAMSUNG_DEV_TS |
| help |
| Machine support for the Samsung SMDK6410 |
| |
| # At least some of the SMDK6410s were shipped with the card detect |
| # for the MMC/SD slots connected to the same input. This means that |
| # either the boards need to be altered to have channel0 to an alternate |
| # configuration or that only one slot can be used. |
| |
| choice |
| prompt "SMDK6410 MMC/SD slot setup" |
| depends on MACH_SMDK6410 |
| |
| config SMDK6410_SD_CH0 |
| bool "Use channel 0 only" |
| depends on MACH_SMDK6410 |
| help |
| Select CON7 (channel 0) as the MMC/SD slot, as |
| at least some SMDK6410 boards come with the |
| resistors fitted so that the card detects for |
| channels 0 and 1 are the same. |
| |
| config SMDK6410_SD_CH1 |
| bool "Use channel 1 only" |
| depends on MACH_SMDK6410 |
| help |
| Select CON6 (channel 1) as the MMC/SD slot, as |
| at least some SMDK6410 boards come with the |
| resistors fitted so that the card detects for |
| channels 0 and 1 are the same. |
| |
| endchoice |
| |
| config SMDK6410_WM1190_EV1 |
| bool "Support Wolfson Microelectronics 1190-EV1 PMIC card" |
| depends on MACH_SMDK6410 |
| depends on I2C=y |
| select MFD_WM8350_I2C |
| select REGULATOR |
| select REGULATOR_WM8350 |
| help |
| The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC |
| and audio daughtercard for the Samsung SMDK6410 reference |
| platform. Enabling this option will build support for this |
| module into the kernel. The presence of the module will be |
| detected at runtime so the resulting kernel can be used |
| with or without the 1190-EV1 fitted. |
| |
| config SMDK6410_WM1192_EV1 |
| bool "Support Wolfson Microelectronics 1192-EV1 PMIC card" |
| depends on MACH_SMDK6410 |
| depends on I2C=y |
| select MFD_WM831X |
| select MFD_WM831X_I2C |
| select REGULATOR |
| select REGULATOR_WM831X |
| help |
| The Wolfson Microelectronics 1192-EV1 is a WM831x based PMIC |
| daughtercard for the Samsung SMDK6410 reference platform. |
| Enabling this option will build support for this module into |
| the kernel. The presence of the daughtercard will be |
| detected at runtime so the resulting kernel can be used |
| with or without the 1192-EV1 fitted. |
| |
| config MACH_NCP |
| bool "NCP" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_I2C1 |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_I2C1 |
| help |
| Machine support for the Samsung NCP |
| |
| config MACH_HMT |
| bool "Airgoo HMT" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C_DEV_FB |
| select S3C_DEV_NAND |
| select S3C_DEV_USB_HOST |
| select SAMSUNG_DEV_PWM |
| help |
| Machine support for the Airgoo HMT |
| |
| config MACH_SMARTQ |
| bool |
| select CPU_S3C6410 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_USB_PHY |
| select S3C_DEV_FB |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_HSMMC2 |
| select S3C_DEV_HWMON |
| select S3C_DEV_RTC |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_USB_HSOTG |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_PWM |
| select SAMSUNG_DEV_TS |
| help |
| Shared machine support for SmartQ 5/7 |
| |
| config MACH_SMARTQ5 |
| bool "SmartQ 5" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select MACH_SMARTQ |
| help |
| Machine support for the SmartQ 5 |
| |
| config MACH_SMARTQ7 |
| bool "SmartQ 7" |
| depends on ATAGS && UNUSED_BOARD_FILES |
| select MACH_SMARTQ |
| help |
| Machine support for the SmartQ 7 |
| |
| config MACH_WLF_CRAGG_6410 |
| bool "Wolfson Cragganmore 6410" |
| depends on ATAGS |
| depends on I2C=y |
| select CPU_S3C6410 |
| select LEDS_GPIO_REGISTER |
| select S3C64XX_DEV_SPI0 |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_I2C1 |
| select S3C64XX_SETUP_IDE |
| select S3C64XX_SETUP_KEYPAD |
| select S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_SPI |
| select S3C64XX_SETUP_USB_PHY |
| select S3C_DEV_FB |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_HSMMC2 |
| select S3C_DEV_I2C1 |
| select S3C_DEV_RTC |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_USB_HSOTG |
| select S3C_DEV_WDT |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_KEYPAD |
| select SAMSUNG_DEV_PWM |
| help |
| Machine support for the Wolfson Cragganmore S3C6410 variant. |
| |
| config MACH_S3C64XX_DT |
| bool "Samsung S3C6400/S3C6410 machine using Device Tree" |
| select CPU_S3C6400 |
| select CPU_S3C6410 |
| select PINCTRL |
| select PINCTRL_S3C64XX |
| help |
| Machine support for Samsung S3C6400/S3C6410 machines with Device Tree |
| enabled. |
| Select this if a fdt blob is available for your S3C64XX SoC based |
| board. |
| Note: This is under development and not all peripherals can be |
| supported with this machine file. |
| |
| endif |
