| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * GPIO driver for the ACCES 104-IDI-48 family |
| * Copyright (C) 2015 William Breathitt Gray |
| * |
| * This driver supports the following ACCES devices: 104-IDI-48A, |
| * 104-IDI-48AC, 104-IDI-48B, and 104-IDI-48BC. |
| */ |
| #include <linux/bits.h> |
| #include <linux/device.h> |
| #include <linux/errno.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/io.h> |
| #include <linux/ioport.h> |
| #include <linux/interrupt.h> |
| #include <linux/irqdesc.h> |
| #include <linux/isa.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/spinlock.h> |
| #include <linux/types.h> |
| |
| #include "gpio-i8255.h" |
| |
| MODULE_IMPORT_NS(I8255); |
| |
| #define IDI_48_EXTENT 8 |
| #define MAX_NUM_IDI_48 max_num_isa_dev(IDI_48_EXTENT) |
| |
| static unsigned int base[MAX_NUM_IDI_48]; |
| static unsigned int num_idi_48; |
| module_param_hw_array(base, uint, ioport, &num_idi_48, 0); |
| MODULE_PARM_DESC(base, "ACCES 104-IDI-48 base addresses"); |
| |
| static unsigned int irq[MAX_NUM_IDI_48]; |
| static unsigned int num_irq; |
| module_param_hw_array(irq, uint, irq, &num_irq, 0); |
| MODULE_PARM_DESC(irq, "ACCES 104-IDI-48 interrupt line numbers"); |
| |
| /** |
| * struct idi_48_reg - device register structure |
| * @port0: Port 0 Inputs |
| * @unused: Unused |
| * @port1: Port 1 Inputs |
| * @irq: Read: IRQ Status Register/IRQ Clear |
| * Write: IRQ Enable/Disable |
| */ |
| struct idi_48_reg { |
| u8 port0[3]; |
| u8 unused; |
| u8 port1[3]; |
| u8 irq; |
| }; |
| |
| /** |
| * struct idi_48_gpio - GPIO device private data structure |
| * @chip: instance of the gpio_chip |
| * @lock: synchronization lock to prevent I/O race conditions |
| * @irq_mask: input bits affected by interrupts |
| * @reg: I/O address offset for the device registers |
| * @cos_enb: Change-Of-State IRQ enable boundaries mask |
| */ |
| struct idi_48_gpio { |
| struct gpio_chip chip; |
| spinlock_t lock; |
| unsigned char irq_mask[6]; |
| struct idi_48_reg __iomem *reg; |
| unsigned char cos_enb; |
| }; |
| |
| static int idi_48_gpio_get_direction(struct gpio_chip *chip, unsigned int offset) |
| { |
| return GPIO_LINE_DIRECTION_IN; |
| } |
| |
| static int idi_48_gpio_direction_input(struct gpio_chip *chip, unsigned int offset) |
| { |
| return 0; |
| } |
| |
| static int idi_48_gpio_get(struct gpio_chip *chip, unsigned int offset) |
| { |
| struct idi_48_gpio *const idi48gpio = gpiochip_get_data(chip); |
| void __iomem *const ppi = idi48gpio->reg; |
| |
| return i8255_get(ppi, offset); |
| } |
| |
| static int idi_48_gpio_get_multiple(struct gpio_chip *chip, unsigned long *mask, |
| unsigned long *bits) |
| { |
| struct idi_48_gpio *const idi48gpio = gpiochip_get_data(chip); |
| void __iomem *const ppi = idi48gpio->reg; |
| |
| i8255_get_multiple(ppi, mask, bits, chip->ngpio); |
| |
| return 0; |
| } |
| |
| static void idi_48_irq_ack(struct irq_data *data) |
| { |
| } |
| |
| static void idi_48_irq_mask(struct irq_data *data) |
| { |
| struct gpio_chip *chip = irq_data_get_irq_chip_data(data); |
| struct idi_48_gpio *const idi48gpio = gpiochip_get_data(chip); |
| const unsigned int offset = irqd_to_hwirq(data); |
| const unsigned long boundary = offset / 8; |
| const unsigned long mask = BIT(offset % 8); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&idi48gpio->lock, flags); |
| |
| idi48gpio->irq_mask[boundary] &= ~mask; |
| gpiochip_disable_irq(chip, offset); |
| |
| /* Exit early if there are still input lines with IRQ unmasked */ |
| if (idi48gpio->irq_mask[boundary]) |
| goto exit; |
| |
| idi48gpio->cos_enb &= ~BIT(boundary); |
| |
| iowrite8(idi48gpio->cos_enb, &idi48gpio->reg->irq); |
| |
| exit: |
| spin_unlock_irqrestore(&idi48gpio->lock, flags); |
| } |
| |
| static void idi_48_irq_unmask(struct irq_data *data) |
| { |
| struct gpio_chip *chip = irq_data_get_irq_chip_data(data); |
| struct idi_48_gpio *const idi48gpio = gpiochip_get_data(chip); |
| const unsigned int offset = irqd_to_hwirq(data); |
| const unsigned long boundary = offset / 8; |
| const unsigned long mask = BIT(offset % 8); |
| unsigned int prev_irq_mask; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&idi48gpio->lock, flags); |
| |
| prev_irq_mask = idi48gpio->irq_mask[boundary]; |
| |
| gpiochip_enable_irq(chip, offset); |
| idi48gpio->irq_mask[boundary] |= mask; |
| |
| /* Exit early if IRQ was already unmasked for this boundary */ |
| if (prev_irq_mask) |
| goto exit; |
| |
| idi48gpio->cos_enb |= BIT(boundary); |
| |
| iowrite8(idi48gpio->cos_enb, &idi48gpio->reg->irq); |
| |
| exit: |
| spin_unlock_irqrestore(&idi48gpio->lock, flags); |
| } |
| |
| static int idi_48_irq_set_type(struct irq_data *data, unsigned int flow_type) |
| { |
| /* The only valid irq types are none and both-edges */ |
| if (flow_type != IRQ_TYPE_NONE && |
| (flow_type & IRQ_TYPE_EDGE_BOTH) != IRQ_TYPE_EDGE_BOTH) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static const struct irq_chip idi_48_irqchip = { |
| .name = "104-idi-48", |
| .irq_ack = idi_48_irq_ack, |
| .irq_mask = idi_48_irq_mask, |
| .irq_unmask = idi_48_irq_unmask, |
| .irq_set_type = idi_48_irq_set_type, |
| .flags = IRQCHIP_IMMUTABLE, |
| GPIOCHIP_IRQ_RESOURCE_HELPERS, |
| }; |
| |
| static irqreturn_t idi_48_irq_handler(int irq, void *dev_id) |
| { |
| struct idi_48_gpio *const idi48gpio = dev_id; |
| unsigned long cos_status; |
| unsigned long boundary; |
| unsigned long irq_mask; |
| unsigned long bit_num; |
| unsigned long gpio; |
| struct gpio_chip *const chip = &idi48gpio->chip; |
| |
| spin_lock(&idi48gpio->lock); |
| |
| cos_status = ioread8(&idi48gpio->reg->irq); |
| |
| /* IRQ Status (bit 6) is active low (0 = IRQ generated by device) */ |
| if (cos_status & BIT(6)) { |
| spin_unlock(&idi48gpio->lock); |
| return IRQ_NONE; |
| } |
| |
| /* Bit 0-5 indicate which Change-Of-State boundary triggered the IRQ */ |
| cos_status &= 0x3F; |
| |
| for_each_set_bit(boundary, &cos_status, 6) { |
| irq_mask = idi48gpio->irq_mask[boundary]; |
| |
| for_each_set_bit(bit_num, &irq_mask, 8) { |
| gpio = bit_num + boundary * 8; |
| |
| generic_handle_domain_irq(chip->irq.domain, |
| gpio); |
| } |
| } |
| |
| spin_unlock(&idi48gpio->lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| #define IDI48_NGPIO 48 |
| static const char *idi48_names[IDI48_NGPIO] = { |
| "Bit 0 A", "Bit 1 A", "Bit 2 A", "Bit 3 A", "Bit 4 A", "Bit 5 A", |
| "Bit 6 A", "Bit 7 A", "Bit 8 A", "Bit 9 A", "Bit 10 A", "Bit 11 A", |
| "Bit 12 A", "Bit 13 A", "Bit 14 A", "Bit 15 A", "Bit 16 A", "Bit 17 A", |
| "Bit 18 A", "Bit 19 A", "Bit 20 A", "Bit 21 A", "Bit 22 A", "Bit 23 A", |
| "Bit 0 B", "Bit 1 B", "Bit 2 B", "Bit 3 B", "Bit 4 B", "Bit 5 B", |
| "Bit 6 B", "Bit 7 B", "Bit 8 B", "Bit 9 B", "Bit 10 B", "Bit 11 B", |
| "Bit 12 B", "Bit 13 B", "Bit 14 B", "Bit 15 B", "Bit 16 B", "Bit 17 B", |
| "Bit 18 B", "Bit 19 B", "Bit 20 B", "Bit 21 B", "Bit 22 B", "Bit 23 B" |
| }; |
| |
| static int idi_48_irq_init_hw(struct gpio_chip *gc) |
| { |
| struct idi_48_gpio *const idi48gpio = gpiochip_get_data(gc); |
| |
| /* Disable IRQ by default */ |
| iowrite8(0, &idi48gpio->reg->irq); |
| ioread8(&idi48gpio->reg->irq); |
| |
| return 0; |
| } |
| |
| static int idi_48_probe(struct device *dev, unsigned int id) |
| { |
| struct idi_48_gpio *idi48gpio; |
| const char *const name = dev_name(dev); |
| struct gpio_irq_chip *girq; |
| int err; |
| |
| idi48gpio = devm_kzalloc(dev, sizeof(*idi48gpio), GFP_KERNEL); |
| if (!idi48gpio) |
| return -ENOMEM; |
| |
| if (!devm_request_region(dev, base[id], IDI_48_EXTENT, name)) { |
| dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n", |
| base[id], base[id] + IDI_48_EXTENT); |
| return -EBUSY; |
| } |
| |
| idi48gpio->reg = devm_ioport_map(dev, base[id], IDI_48_EXTENT); |
| if (!idi48gpio->reg) |
| return -ENOMEM; |
| |
| idi48gpio->chip.label = name; |
| idi48gpio->chip.parent = dev; |
| idi48gpio->chip.owner = THIS_MODULE; |
| idi48gpio->chip.base = -1; |
| idi48gpio->chip.ngpio = IDI48_NGPIO; |
| idi48gpio->chip.names = idi48_names; |
| idi48gpio->chip.get_direction = idi_48_gpio_get_direction; |
| idi48gpio->chip.direction_input = idi_48_gpio_direction_input; |
| idi48gpio->chip.get = idi_48_gpio_get; |
| idi48gpio->chip.get_multiple = idi_48_gpio_get_multiple; |
| |
| girq = &idi48gpio->chip.irq; |
| gpio_irq_chip_set_chip(girq, &idi_48_irqchip); |
| /* This will let us handle the parent IRQ in the driver */ |
| girq->parent_handler = NULL; |
| girq->num_parents = 0; |
| girq->parents = NULL; |
| girq->default_type = IRQ_TYPE_NONE; |
| girq->handler = handle_edge_irq; |
| girq->init_hw = idi_48_irq_init_hw; |
| |
| spin_lock_init(&idi48gpio->lock); |
| |
| err = devm_gpiochip_add_data(dev, &idi48gpio->chip, idi48gpio); |
| if (err) { |
| dev_err(dev, "GPIO registering failed (%d)\n", err); |
| return err; |
| } |
| |
| err = devm_request_irq(dev, irq[id], idi_48_irq_handler, IRQF_SHARED, |
| name, idi48gpio); |
| if (err) { |
| dev_err(dev, "IRQ handler registering failed (%d)\n", err); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static struct isa_driver idi_48_driver = { |
| .probe = idi_48_probe, |
| .driver = { |
| .name = "104-idi-48" |
| }, |
| }; |
| module_isa_driver_with_irq(idi_48_driver, num_idi_48, num_irq); |
| |
| MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>"); |
| MODULE_DESCRIPTION("ACCES 104-IDI-48 GPIO driver"); |
| MODULE_LICENSE("GPL v2"); |