| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2020 MaxLinear, Inc. |
| * |
| * This driver is a hardware monitoring driver for PVT controller |
| * (MR75203) which is used to configure & control Moortec embedded |
| * analog IP to enable multiple embedded temperature sensor(TS), |
| * voltage monitor(VM) & process detector(PD) modules. |
| */ |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/debugfs.h> |
| #include <linux/hwmon.h> |
| #include <linux/module.h> |
| #include <linux/mod_devicetable.h> |
| #include <linux/mutex.h> |
| #include <linux/platform_device.h> |
| #include <linux/property.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| #include <linux/slab.h> |
| #include <linux/units.h> |
| |
| /* PVT Common register */ |
| #define PVT_IP_CONFIG 0x04 |
| #define TS_NUM_MSK GENMASK(4, 0) |
| #define TS_NUM_SFT 0 |
| #define PD_NUM_MSK GENMASK(12, 8) |
| #define PD_NUM_SFT 8 |
| #define VM_NUM_MSK GENMASK(20, 16) |
| #define VM_NUM_SFT 16 |
| #define CH_NUM_MSK GENMASK(31, 24) |
| #define CH_NUM_SFT 24 |
| |
| #define VM_NUM_MAX (VM_NUM_MSK >> VM_NUM_SFT) |
| |
| /* Macro Common Register */ |
| #define CLK_SYNTH 0x00 |
| #define CLK_SYNTH_LO_SFT 0 |
| #define CLK_SYNTH_HI_SFT 8 |
| #define CLK_SYNTH_HOLD_SFT 16 |
| #define CLK_SYNTH_EN BIT(24) |
| #define CLK_SYS_CYCLES_MAX 514 |
| #define CLK_SYS_CYCLES_MIN 2 |
| |
| #define SDIF_DISABLE 0x04 |
| |
| #define SDIF_STAT 0x08 |
| #define SDIF_BUSY BIT(0) |
| #define SDIF_LOCK BIT(1) |
| |
| #define SDIF_W 0x0c |
| #define SDIF_PROG BIT(31) |
| #define SDIF_WRN_W BIT(27) |
| #define SDIF_WRN_R 0x00 |
| #define SDIF_ADDR_SFT 24 |
| |
| #define SDIF_HALT 0x10 |
| #define SDIF_CTRL 0x14 |
| #define SDIF_SMPL_CTRL 0x20 |
| |
| /* TS & PD Individual Macro Register */ |
| #define COM_REG_SIZE 0x40 |
| |
| #define SDIF_DONE(n) (COM_REG_SIZE + 0x14 + 0x40 * (n)) |
| #define SDIF_SMPL_DONE BIT(0) |
| |
| #define SDIF_DATA(n) (COM_REG_SIZE + 0x18 + 0x40 * (n)) |
| #define SAMPLE_DATA_MSK GENMASK(15, 0) |
| |
| #define HILO_RESET(n) (COM_REG_SIZE + 0x2c + 0x40 * (n)) |
| |
| /* VM Individual Macro Register */ |
| #define VM_COM_REG_SIZE 0x200 |
| #define VM_SDIF_DONE(vm) (VM_COM_REG_SIZE + 0x34 + 0x200 * (vm)) |
| #define VM_SDIF_DATA(vm, ch) \ |
| (VM_COM_REG_SIZE + 0x40 + 0x200 * (vm) + 0x4 * (ch)) |
| |
| /* SDA Slave Register */ |
| #define IP_CTRL 0x00 |
| #define IP_RST_REL BIT(1) |
| #define IP_RUN_CONT BIT(3) |
| #define IP_AUTO BIT(8) |
| #define IP_VM_MODE BIT(10) |
| |
| #define IP_CFG 0x01 |
| #define CFG0_MODE_2 BIT(0) |
| #define CFG0_PARALLEL_OUT 0 |
| #define CFG0_12_BIT 0 |
| #define CFG1_VOL_MEAS_MODE 0 |
| #define CFG1_PARALLEL_OUT 0 |
| #define CFG1_14_BIT 0 |
| |
| #define IP_DATA 0x03 |
| |
| #define IP_POLL 0x04 |
| #define VM_CH_INIT BIT(20) |
| #define VM_CH_REQ BIT(21) |
| |
| #define IP_TMR 0x05 |
| #define POWER_DELAY_CYCLE_256 0x100 |
| #define POWER_DELAY_CYCLE_64 0x40 |
| |
| #define PVT_POLL_DELAY_US 20 |
| #define PVT_POLL_TIMEOUT_US 20000 |
| #define PVT_CONV_BITS 10 |
| #define PVT_N_CONST 90 |
| #define PVT_R_CONST 245805 |
| |
| #define PVT_TEMP_MIN_mC -40000 |
| #define PVT_TEMP_MAX_mC 125000 |
| |
| /* Temperature coefficients for series 5 */ |
| #define PVT_SERIES5_H_CONST 200000 |
| #define PVT_SERIES5_G_CONST 60000 |
| #define PVT_SERIES5_J_CONST -100 |
| #define PVT_SERIES5_CAL5_CONST 4094 |
| |
| /* Temperature coefficients for series 6 */ |
| #define PVT_SERIES6_H_CONST 249400 |
| #define PVT_SERIES6_G_CONST 57400 |
| #define PVT_SERIES6_J_CONST 0 |
| #define PVT_SERIES6_CAL5_CONST 4096 |
| |
| #define TEMPERATURE_SENSOR_SERIES_5 5 |
| #define TEMPERATURE_SENSOR_SERIES_6 6 |
| |
| #define PRE_SCALER_X1 1 |
| #define PRE_SCALER_X2 2 |
| |
| /** |
| * struct voltage_device - VM single input parameters. |
| * @vm_map: Map channel number to VM index. |
| * @ch_map: Map channel number to channel index. |
| * @pre_scaler: Pre scaler value (1 or 2) used to normalize the voltage output |
| * result. |
| * |
| * The structure provides mapping between channel-number (0..N-1) to VM-index |
| * (0..num_vm-1) and channel-index (0..ch_num-1) where N = num_vm * ch_num. |
| * It also provides normalization factor for the VM equation. |
| */ |
| struct voltage_device { |
| u32 vm_map; |
| u32 ch_map; |
| u32 pre_scaler; |
| }; |
| |
| /** |
| * struct voltage_channels - VM channel count. |
| * @total: Total number of channels in all VMs. |
| * @max: Maximum number of channels among all VMs. |
| * |
| * The structure provides channel count information across all VMs. |
| */ |
| struct voltage_channels { |
| u32 total; |
| u8 max; |
| }; |
| |
| struct temp_coeff { |
| u32 h; |
| u32 g; |
| u32 cal5; |
| s32 j; |
| }; |
| |
| struct pvt_device { |
| struct regmap *c_map; |
| struct regmap *t_map; |
| struct regmap *p_map; |
| struct regmap *v_map; |
| struct clk *clk; |
| struct reset_control *rst; |
| struct dentry *dbgfs_dir; |
| struct voltage_device *vd; |
| struct voltage_channels vm_channels; |
| struct temp_coeff ts_coeff; |
| u32 t_num; |
| u32 p_num; |
| u32 v_num; |
| u32 ip_freq; |
| }; |
| |
| static ssize_t pvt_ts_coeff_j_read(struct file *file, char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct pvt_device *pvt = file->private_data; |
| unsigned int len; |
| char buf[13]; |
| |
| len = scnprintf(buf, sizeof(buf), "%d\n", pvt->ts_coeff.j); |
| |
| return simple_read_from_buffer(user_buf, count, ppos, buf, len); |
| } |
| |
| static ssize_t pvt_ts_coeff_j_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct pvt_device *pvt = file->private_data; |
| int ret; |
| |
| ret = kstrtos32_from_user(user_buf, count, 0, &pvt->ts_coeff.j); |
| if (ret) |
| return ret; |
| |
| return count; |
| } |
| |
| static const struct file_operations pvt_ts_coeff_j_fops = { |
| .read = pvt_ts_coeff_j_read, |
| .write = pvt_ts_coeff_j_write, |
| .open = simple_open, |
| .owner = THIS_MODULE, |
| .llseek = default_llseek, |
| }; |
| |
| static void devm_pvt_ts_dbgfs_remove(void *data) |
| { |
| struct pvt_device *pvt = (struct pvt_device *)data; |
| |
| debugfs_remove_recursive(pvt->dbgfs_dir); |
| pvt->dbgfs_dir = NULL; |
| } |
| |
| static int pvt_ts_dbgfs_create(struct pvt_device *pvt, struct device *dev) |
| { |
| pvt->dbgfs_dir = debugfs_create_dir(dev_name(dev), NULL); |
| |
| debugfs_create_u32("ts_coeff_h", 0644, pvt->dbgfs_dir, |
| &pvt->ts_coeff.h); |
| debugfs_create_u32("ts_coeff_g", 0644, pvt->dbgfs_dir, |
| &pvt->ts_coeff.g); |
| debugfs_create_u32("ts_coeff_cal5", 0644, pvt->dbgfs_dir, |
| &pvt->ts_coeff.cal5); |
| debugfs_create_file("ts_coeff_j", 0644, pvt->dbgfs_dir, pvt, |
| &pvt_ts_coeff_j_fops); |
| |
| return devm_add_action_or_reset(dev, devm_pvt_ts_dbgfs_remove, pvt); |
| } |
| |
| static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type, |
| u32 attr, int channel) |
| { |
| switch (type) { |
| case hwmon_temp: |
| if (attr == hwmon_temp_input) |
| return 0444; |
| break; |
| case hwmon_in: |
| if (attr == hwmon_in_input) |
| return 0444; |
| break; |
| default: |
| break; |
| } |
| return 0; |
| } |
| |
| static long pvt_calc_temp(struct pvt_device *pvt, u32 nbs) |
| { |
| /* |
| * Convert the register value to degrees centigrade temperature: |
| * T = G + H * (n / cal5 - 0.5) + J * F |
| */ |
| struct temp_coeff *ts_coeff = &pvt->ts_coeff; |
| |
| s64 tmp = ts_coeff->g + |
| div_s64(ts_coeff->h * (s64)nbs, ts_coeff->cal5) - |
| ts_coeff->h / 2 + |
| div_s64(ts_coeff->j * (s64)pvt->ip_freq, HZ_PER_MHZ); |
| |
| return clamp_val(tmp, PVT_TEMP_MIN_mC, PVT_TEMP_MAX_mC); |
| } |
| |
| static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val) |
| { |
| struct pvt_device *pvt = dev_get_drvdata(dev); |
| struct regmap *t_map = pvt->t_map; |
| u32 stat, nbs; |
| int ret; |
| |
| switch (attr) { |
| case hwmon_temp_input: |
| ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel), |
| stat, stat & SDIF_SMPL_DONE, |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(t_map, SDIF_DATA(channel), &nbs); |
| if (ret < 0) |
| return ret; |
| |
| nbs &= SAMPLE_DATA_MSK; |
| |
| /* |
| * Convert the register value to |
| * degrees centigrade temperature |
| */ |
| *val = pvt_calc_temp(pvt, nbs); |
| |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val) |
| { |
| struct pvt_device *pvt = dev_get_drvdata(dev); |
| struct regmap *v_map = pvt->v_map; |
| u32 n, stat, pre_scaler; |
| u8 vm_idx, ch_idx; |
| int ret; |
| |
| if (channel >= pvt->vm_channels.total) |
| return -EINVAL; |
| |
| vm_idx = pvt->vd[channel].vm_map; |
| ch_idx = pvt->vd[channel].ch_map; |
| |
| switch (attr) { |
| case hwmon_in_input: |
| ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx), |
| stat, stat & SDIF_SMPL_DONE, |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx, ch_idx), &n); |
| if (ret < 0) |
| return ret; |
| |
| n &= SAMPLE_DATA_MSK; |
| pre_scaler = pvt->vd[channel].pre_scaler; |
| /* |
| * Convert the N bitstream count into voltage. |
| * To support negative voltage calculation for 64bit machines |
| * n must be cast to long, since n and *val differ both in |
| * signedness and in size. |
| * Division is used instead of right shift, because for signed |
| * numbers, the sign bit is used to fill the vacated bit |
| * positions, and if the number is negative, 1 is used. |
| * BIT(x) may not be used instead of (1 << x) because it's |
| * unsigned. |
| */ |
| *val = pre_scaler * (PVT_N_CONST * (long)n - PVT_R_CONST) / |
| (1 << PVT_CONV_BITS); |
| |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int pvt_read(struct device *dev, enum hwmon_sensor_types type, |
| u32 attr, int channel, long *val) |
| { |
| switch (type) { |
| case hwmon_temp: |
| return pvt_read_temp(dev, attr, channel, val); |
| case hwmon_in: |
| return pvt_read_in(dev, attr, channel, val); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static struct hwmon_channel_info pvt_temp = { |
| .type = hwmon_temp, |
| }; |
| |
| static struct hwmon_channel_info pvt_in = { |
| .type = hwmon_in, |
| }; |
| |
| static const struct hwmon_ops pvt_hwmon_ops = { |
| .is_visible = pvt_is_visible, |
| .read = pvt_read, |
| }; |
| |
| static struct hwmon_chip_info pvt_chip_info = { |
| .ops = &pvt_hwmon_ops, |
| }; |
| |
| static int pvt_init(struct pvt_device *pvt) |
| { |
| u16 sys_freq, key, middle, low = 4, high = 8; |
| struct regmap *t_map = pvt->t_map; |
| struct regmap *p_map = pvt->p_map; |
| struct regmap *v_map = pvt->v_map; |
| u32 t_num = pvt->t_num; |
| u32 p_num = pvt->p_num; |
| u32 v_num = pvt->v_num; |
| u32 clk_synth, val; |
| int ret; |
| |
| sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ; |
| while (high >= low) { |
| middle = (low + high + 1) / 2; |
| key = DIV_ROUND_CLOSEST(sys_freq, middle); |
| if (key > CLK_SYS_CYCLES_MAX) { |
| low = middle + 1; |
| continue; |
| } else if (key < CLK_SYS_CYCLES_MIN) { |
| high = middle - 1; |
| continue; |
| } else { |
| break; |
| } |
| } |
| |
| /* |
| * The system supports 'clk_sys' to 'clk_ip' frequency ratios |
| * from 2:1 to 512:1 |
| */ |
| key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2; |
| |
| clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT | |
| (key >> 1) << CLK_SYNTH_HI_SFT | |
| (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN; |
| |
| pvt->ip_freq = clk_get_rate(pvt->clk) / (key + 2); |
| |
| if (t_num) { |
| ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, SDIF_HALT, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, CLK_SYNTH, clk_synth); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, SDIF_DISABLE, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT | |
| IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | |
| IP_CTRL << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| } |
| |
| if (p_num) { |
| ret = regmap_write(p_map, SDIF_HALT, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(p_map, CLK_SYNTH, clk_synth); |
| if (ret < 0) |
| return ret; |
| } |
| |
| if (v_num) { |
| ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, SDIF_HALT, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, CLK_SYNTH, clk_synth); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, SDIF_DISABLE, 0x0); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = (BIT(pvt->vm_channels.max) - 1) | VM_CH_INIT | |
| IP_POLL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT | |
| CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE | |
| IP_CTRL << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if (ret < 0) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static struct regmap_config pvt_regmap_config = { |
| .reg_bits = 32, |
| .reg_stride = 4, |
| .val_bits = 32, |
| }; |
| |
| static int pvt_get_regmap(struct platform_device *pdev, char *reg_name, |
| struct pvt_device *pvt) |
| { |
| struct device *dev = &pdev->dev; |
| struct regmap **reg_map; |
| void __iomem *io_base; |
| |
| if (!strcmp(reg_name, "common")) |
| reg_map = &pvt->c_map; |
| else if (!strcmp(reg_name, "ts")) |
| reg_map = &pvt->t_map; |
| else if (!strcmp(reg_name, "pd")) |
| reg_map = &pvt->p_map; |
| else if (!strcmp(reg_name, "vm")) |
| reg_map = &pvt->v_map; |
| else |
| return -EINVAL; |
| |
| io_base = devm_platform_ioremap_resource_byname(pdev, reg_name); |
| if (IS_ERR(io_base)) |
| return PTR_ERR(io_base); |
| |
| pvt_regmap_config.name = reg_name; |
| *reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config); |
| if (IS_ERR(*reg_map)) { |
| dev_err(dev, "failed to init register map\n"); |
| return PTR_ERR(*reg_map); |
| } |
| |
| return 0; |
| } |
| |
| static void pvt_reset_control_assert(void *data) |
| { |
| struct pvt_device *pvt = data; |
| |
| reset_control_assert(pvt->rst); |
| } |
| |
| static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt) |
| { |
| int ret; |
| |
| ret = reset_control_deassert(pvt->rst); |
| if (ret) |
| return ret; |
| |
| return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt); |
| } |
| |
| static int pvt_get_active_channel(struct device *dev, struct pvt_device *pvt, |
| u32 vm_num, u32 ch_num, u8 *vm_idx) |
| { |
| u8 vm_active_ch[VM_NUM_MAX]; |
| int ret, i, j, k; |
| |
| ret = device_property_read_u8_array(dev, "moortec,vm-active-channels", |
| vm_active_ch, vm_num); |
| if (ret) { |
| /* |
| * Incase "moortec,vm-active-channels" property is not defined, |
| * we assume each VM sensor has all of its channels active. |
| */ |
| memset(vm_active_ch, ch_num, vm_num); |
| pvt->vm_channels.max = ch_num; |
| pvt->vm_channels.total = ch_num * vm_num; |
| } else { |
| for (i = 0; i < vm_num; i++) { |
| if (vm_active_ch[i] > ch_num) { |
| dev_err(dev, "invalid active channels: %u\n", |
| vm_active_ch[i]); |
| return -EINVAL; |
| } |
| |
| pvt->vm_channels.total += vm_active_ch[i]; |
| |
| if (vm_active_ch[i] > pvt->vm_channels.max) |
| pvt->vm_channels.max = vm_active_ch[i]; |
| } |
| } |
| |
| /* |
| * Map between the channel-number to VM-index and channel-index. |
| * Example - 3 VMs, "moortec,vm_active_ch" = <5 2 4>: |
| * vm_map = [0 0 0 0 0 1 1 2 2 2 2] |
| * ch_map = [0 1 2 3 4 0 1 0 1 2 3] |
| */ |
| pvt->vd = devm_kcalloc(dev, pvt->vm_channels.total, sizeof(*pvt->vd), |
| GFP_KERNEL); |
| if (!pvt->vd) |
| return -ENOMEM; |
| |
| k = 0; |
| for (i = 0; i < vm_num; i++) { |
| for (j = 0; j < vm_active_ch[i]; j++) { |
| pvt->vd[k].vm_map = vm_idx[i]; |
| pvt->vd[k].ch_map = j; |
| k++; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int pvt_get_pre_scaler(struct device *dev, struct pvt_device *pvt) |
| { |
| u8 *pre_scaler_ch_list; |
| int i, ret, num_ch; |
| u32 channel; |
| |
| /* Set default pre-scaler value to be 1. */ |
| for (i = 0; i < pvt->vm_channels.total; i++) |
| pvt->vd[i].pre_scaler = PRE_SCALER_X1; |
| |
| /* Get number of channels configured in "moortec,vm-pre-scaler-x2". */ |
| num_ch = device_property_count_u8(dev, "moortec,vm-pre-scaler-x2"); |
| if (num_ch <= 0) |
| return 0; |
| |
| pre_scaler_ch_list = kcalloc(num_ch, sizeof(*pre_scaler_ch_list), |
| GFP_KERNEL); |
| if (!pre_scaler_ch_list) |
| return -ENOMEM; |
| |
| /* Get list of all channels that have pre-scaler of 2. */ |
| ret = device_property_read_u8_array(dev, "moortec,vm-pre-scaler-x2", |
| pre_scaler_ch_list, num_ch); |
| if (ret) |
| goto out; |
| |
| for (i = 0; i < num_ch; i++) { |
| channel = pre_scaler_ch_list[i]; |
| pvt->vd[channel].pre_scaler = PRE_SCALER_X2; |
| } |
| |
| out: |
| kfree(pre_scaler_ch_list); |
| |
| return ret; |
| } |
| |
| static int pvt_set_temp_coeff(struct device *dev, struct pvt_device *pvt) |
| { |
| struct temp_coeff *ts_coeff = &pvt->ts_coeff; |
| u32 series; |
| int ret; |
| |
| /* Incase ts-series property is not defined, use default 5. */ |
| ret = device_property_read_u32(dev, "moortec,ts-series", &series); |
| if (ret) |
| series = TEMPERATURE_SENSOR_SERIES_5; |
| |
| switch (series) { |
| case TEMPERATURE_SENSOR_SERIES_5: |
| ts_coeff->h = PVT_SERIES5_H_CONST; |
| ts_coeff->g = PVT_SERIES5_G_CONST; |
| ts_coeff->j = PVT_SERIES5_J_CONST; |
| ts_coeff->cal5 = PVT_SERIES5_CAL5_CONST; |
| break; |
| case TEMPERATURE_SENSOR_SERIES_6: |
| ts_coeff->h = PVT_SERIES6_H_CONST; |
| ts_coeff->g = PVT_SERIES6_G_CONST; |
| ts_coeff->j = PVT_SERIES6_J_CONST; |
| ts_coeff->cal5 = PVT_SERIES6_CAL5_CONST; |
| break; |
| default: |
| dev_err(dev, "invalid temperature sensor series (%u)\n", |
| series); |
| return -EINVAL; |
| } |
| |
| dev_dbg(dev, "temperature sensor series = %u\n", series); |
| |
| /* Override ts-coeff-h/g/j/cal5 if they are defined. */ |
| device_property_read_u32(dev, "moortec,ts-coeff-h", &ts_coeff->h); |
| device_property_read_u32(dev, "moortec,ts-coeff-g", &ts_coeff->g); |
| device_property_read_u32(dev, "moortec,ts-coeff-j", &ts_coeff->j); |
| device_property_read_u32(dev, "moortec,ts-coeff-cal5", &ts_coeff->cal5); |
| |
| dev_dbg(dev, "ts-coeff: h = %u, g = %u, j = %d, cal5 = %u\n", |
| ts_coeff->h, ts_coeff->g, ts_coeff->j, ts_coeff->cal5); |
| |
| return 0; |
| } |
| |
| static int mr75203_probe(struct platform_device *pdev) |
| { |
| u32 ts_num, vm_num, pd_num, ch_num, val, index, i; |
| const struct hwmon_channel_info **pvt_info; |
| struct device *dev = &pdev->dev; |
| u32 *temp_config, *in_config; |
| struct device *hwmon_dev; |
| struct pvt_device *pvt; |
| int ret; |
| |
| pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL); |
| if (!pvt) |
| return -ENOMEM; |
| |
| ret = pvt_get_regmap(pdev, "common", pvt); |
| if (ret) |
| return ret; |
| |
| pvt->clk = devm_clk_get_enabled(dev, NULL); |
| if (IS_ERR(pvt->clk)) |
| return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n"); |
| |
| pvt->rst = devm_reset_control_get_optional_exclusive(dev, NULL); |
| if (IS_ERR(pvt->rst)) |
| return dev_err_probe(dev, PTR_ERR(pvt->rst), |
| "failed to get reset control\n"); |
| |
| if (pvt->rst) { |
| ret = pvt_reset_control_deassert(dev, pvt); |
| if (ret) |
| return dev_err_probe(dev, ret, |
| "cannot deassert reset control\n"); |
| } |
| |
| ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val); |
| if (ret < 0) |
| return ret; |
| |
| ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT; |
| pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT; |
| vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT; |
| ch_num = (val & CH_NUM_MSK) >> CH_NUM_SFT; |
| pvt->t_num = ts_num; |
| pvt->p_num = pd_num; |
| pvt->v_num = vm_num; |
| val = 0; |
| if (ts_num) |
| val++; |
| if (vm_num) |
| val++; |
| if (!val) |
| return -ENODEV; |
| |
| pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL); |
| if (!pvt_info) |
| return -ENOMEM; |
| pvt_info[0] = HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ); |
| index = 1; |
| |
| if (ts_num) { |
| ret = pvt_get_regmap(pdev, "ts", pvt); |
| if (ret) |
| return ret; |
| |
| ret = pvt_set_temp_coeff(dev, pvt); |
| if (ret) |
| return ret; |
| |
| temp_config = devm_kcalloc(dev, ts_num + 1, |
| sizeof(*temp_config), GFP_KERNEL); |
| if (!temp_config) |
| return -ENOMEM; |
| |
| memset32(temp_config, HWMON_T_INPUT, ts_num); |
| pvt_temp.config = temp_config; |
| pvt_info[index++] = &pvt_temp; |
| |
| pvt_ts_dbgfs_create(pvt, dev); |
| } |
| |
| if (pd_num) { |
| ret = pvt_get_regmap(pdev, "pd", pvt); |
| if (ret) |
| return ret; |
| } |
| |
| if (vm_num) { |
| u8 vm_idx[VM_NUM_MAX]; |
| |
| ret = pvt_get_regmap(pdev, "vm", pvt); |
| if (ret) |
| return ret; |
| |
| ret = device_property_read_u8_array(dev, "intel,vm-map", vm_idx, |
| vm_num); |
| if (ret) { |
| /* |
| * Incase intel,vm-map property is not defined, we |
| * assume incremental channel numbers. |
| */ |
| for (i = 0; i < vm_num; i++) |
| vm_idx[i] = i; |
| } else { |
| for (i = 0; i < vm_num; i++) |
| if (vm_idx[i] >= vm_num || vm_idx[i] == 0xff) { |
| pvt->v_num = i; |
| vm_num = i; |
| break; |
| } |
| } |
| |
| ret = pvt_get_active_channel(dev, pvt, vm_num, ch_num, vm_idx); |
| if (ret) |
| return ret; |
| |
| ret = pvt_get_pre_scaler(dev, pvt); |
| if (ret) |
| return ret; |
| |
| in_config = devm_kcalloc(dev, pvt->vm_channels.total + 1, |
| sizeof(*in_config), GFP_KERNEL); |
| if (!in_config) |
| return -ENOMEM; |
| |
| memset32(in_config, HWMON_I_INPUT, pvt->vm_channels.total); |
| in_config[pvt->vm_channels.total] = 0; |
| pvt_in.config = in_config; |
| |
| pvt_info[index++] = &pvt_in; |
| } |
| |
| ret = pvt_init(pvt); |
| if (ret) { |
| dev_err(dev, "failed to init pvt: %d\n", ret); |
| return ret; |
| } |
| |
| pvt_chip_info.info = pvt_info; |
| hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt", |
| pvt, |
| &pvt_chip_info, |
| NULL); |
| |
| return PTR_ERR_OR_ZERO(hwmon_dev); |
| } |
| |
| static const struct of_device_id moortec_pvt_of_match[] = { |
| { .compatible = "moortec,mr75203" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, moortec_pvt_of_match); |
| |
| static struct platform_driver moortec_pvt_driver = { |
| .driver = { |
| .name = "moortec-pvt", |
| .of_match_table = moortec_pvt_of_match, |
| }, |
| .probe = mr75203_probe, |
| }; |
| module_platform_driver(moortec_pvt_driver); |
| |
| MODULE_LICENSE("GPL v2"); |