| /* |
| * Copyright (C) 2005-2006 Micronas USA Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License (Version 2) as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software Foundation, |
| * Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/spinlock.h> |
| #include <linux/wait.h> |
| #include <linux/list.h> |
| #include <linux/slab.h> |
| #include <linux/time.h> |
| #include <linux/mm.h> |
| #include <linux/usb.h> |
| #include <linux/i2c.h> |
| #include <asm/byteorder.h> |
| #include <media/v4l2-common.h> |
| |
| #include "saa7134-reg.h" |
| #include "saa7134.h" |
| #include "go7007-priv.h" |
| |
| #define GO7007_HPI_DEBUG |
| |
| enum hpi_address { |
| HPI_ADDR_VIDEO_BUFFER = 0xe4, |
| HPI_ADDR_INIT_BUFFER = 0xea, |
| HPI_ADDR_INTR_RET_VALUE = 0xee, |
| HPI_ADDR_INTR_RET_DATA = 0xec, |
| HPI_ADDR_INTR_STATUS = 0xf4, |
| HPI_ADDR_INTR_WR_PARAM = 0xf6, |
| HPI_ADDR_INTR_WR_INDEX = 0xf8, |
| }; |
| |
| enum gpio_command { |
| GPIO_COMMAND_RESET = 0x00, /* 000b */ |
| GPIO_COMMAND_REQ1 = 0x04, /* 001b */ |
| GPIO_COMMAND_WRITE = 0x20, /* 010b */ |
| GPIO_COMMAND_REQ2 = 0x24, /* 011b */ |
| GPIO_COMMAND_READ = 0x80, /* 100b */ |
| GPIO_COMMAND_VIDEO = 0x84, /* 101b */ |
| GPIO_COMMAND_IDLE = 0xA0, /* 110b */ |
| GPIO_COMMAND_ADDR = 0xA4, /* 111b */ |
| }; |
| |
| struct saa7134_go7007 { |
| struct saa7134_dev *dev; |
| u8 *top; |
| u8 *bottom; |
| dma_addr_t top_dma; |
| dma_addr_t bottom_dma; |
| }; |
| |
| static struct go7007_board_info board_voyager = { |
| .firmware = "go7007tv.bin", |
| .flags = 0, |
| .sensor_flags = GO7007_SENSOR_656 | |
| GO7007_SENSOR_VALID_ENABLE | |
| GO7007_SENSOR_TV | |
| GO7007_SENSOR_VBI, |
| .audio_flags = GO7007_AUDIO_I2S_MODE_1 | |
| GO7007_AUDIO_WORD_16, |
| .audio_rate = 48000, |
| .audio_bclk_div = 8, |
| .audio_main_div = 2, |
| .hpi_buffer_cap = 7, |
| .num_inputs = 1, |
| .inputs = { |
| { |
| .name = "SAA7134", |
| }, |
| }, |
| }; |
| |
| /********************* Driver for GPIO HPI interface *********************/ |
| |
| static int gpio_write(struct saa7134_dev *dev, u8 addr, u16 data) |
| { |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0xff); |
| |
| /* Write HPI address */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, addr); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_ADDR); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| /* Write low byte */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, data & 0xff); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_WRITE); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| /* Write high byte */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, data >> 8); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_WRITE); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| return 0; |
| } |
| |
| static int gpio_read(struct saa7134_dev *dev, u8 addr, u16 *data) |
| { |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0xff); |
| |
| /* Write HPI address */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, addr); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_ADDR); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0x00); |
| |
| /* Read low byte */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_READ); |
| saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| *data = saa_readb(SAA7134_GPIO_GPSTATUS0); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| /* Read high byte */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_READ); |
| saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| *data |= saa_readb(SAA7134_GPIO_GPSTATUS0) << 8; |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| |
| return 0; |
| } |
| |
| static int saa7134_go7007_interface_reset(struct go7007 *go) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| u32 status; |
| u16 intr_val, intr_data; |
| int count = 20; |
| |
| saa_clearb(SAA7134_TS_PARALLEL, 0x80); /* Disable TS interface */ |
| saa_writeb(SAA7134_GPIO_GPMODE2, 0xa4); |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0xff); |
| |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_REQ1); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_RESET); |
| msleep(1); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_REQ1); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_REQ2); |
| msleep(10); |
| |
| saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| |
| status = saa_readb(SAA7134_GPIO_GPSTATUS2); |
| /*printk(KERN_DEBUG "status is %s\n", status & 0x40 ? "OK" : "not OK"); */ |
| |
| /* enter command mode...(?) */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_REQ1); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_REQ2); |
| |
| do { |
| saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN); |
| status = saa_readb(SAA7134_GPIO_GPSTATUS2); |
| /*printk(KERN_INFO "gpio is %08x\n", saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2)); */ |
| } while (--count > 0); |
| |
| /* Wait for an interrupt to indicate successful hardware reset */ |
| if (go7007_read_interrupt(go, &intr_val, &intr_data) < 0 || |
| (intr_val & ~0x1) != 0x55aa) { |
| printk(KERN_ERR |
| "saa7134-go7007: unable to reset the GO7007\n"); |
| return -1; |
| } |
| return 0; |
| } |
| |
| static int saa7134_go7007_write_interrupt(struct go7007 *go, int addr, int data) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| int i; |
| u16 status_reg; |
| |
| #ifdef GO7007_HPI_DEBUG |
| printk(KERN_DEBUG |
| "saa7134-go7007: WriteInterrupt: %04x %04x\n", addr, data); |
| #endif |
| |
| for (i = 0; i < 100; ++i) { |
| gpio_read(dev, HPI_ADDR_INTR_STATUS, &status_reg); |
| if (!(status_reg & 0x0010)) |
| break; |
| msleep(10); |
| } |
| if (i == 100) { |
| printk(KERN_ERR |
| "saa7134-go7007: device is hung, status reg = 0x%04x\n", |
| status_reg); |
| return -1; |
| } |
| gpio_write(dev, HPI_ADDR_INTR_WR_PARAM, data); |
| gpio_write(dev, HPI_ADDR_INTR_WR_INDEX, addr); |
| |
| return 0; |
| } |
| |
| static int saa7134_go7007_read_interrupt(struct go7007 *go) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| |
| /* XXX we need to wait if there is no interrupt available */ |
| go->interrupt_available = 1; |
| gpio_read(dev, HPI_ADDR_INTR_RET_VALUE, &go->interrupt_value); |
| gpio_read(dev, HPI_ADDR_INTR_RET_DATA, &go->interrupt_data); |
| #ifdef GO7007_HPI_DEBUG |
| printk(KERN_DEBUG "saa7134-go7007: ReadInterrupt: %04x %04x\n", |
| go->interrupt_value, go->interrupt_data); |
| #endif |
| return 0; |
| } |
| |
| static void saa7134_go7007_irq_ts_done(struct saa7134_dev *dev, |
| unsigned long status) |
| { |
| struct go7007 *go = video_get_drvdata(dev->empress_dev); |
| struct saa7134_go7007 *saa = go->hpi_context; |
| |
| if (!go->streaming) |
| return; |
| if (0 != (status & 0x000f0000)) |
| printk(KERN_DEBUG "saa7134-go7007: irq: lost %ld\n", |
| (status >> 16) & 0x0f); |
| if (status & 0x100000) { |
| dma_sync_single(&dev->pci->dev, |
| saa->bottom_dma, PAGE_SIZE, DMA_FROM_DEVICE); |
| go7007_parse_video_stream(go, saa->bottom, PAGE_SIZE); |
| saa_writel(SAA7134_RS_BA2(5), cpu_to_le32(saa->bottom_dma)); |
| } else { |
| dma_sync_single(&dev->pci->dev, |
| saa->top_dma, PAGE_SIZE, DMA_FROM_DEVICE); |
| go7007_parse_video_stream(go, saa->top, PAGE_SIZE); |
| saa_writel(SAA7134_RS_BA1(5), cpu_to_le32(saa->top_dma)); |
| } |
| } |
| |
| static int saa7134_go7007_stream_start(struct go7007 *go) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| |
| saa->top_dma = dma_map_page(&dev->pci->dev, virt_to_page(saa->top), |
| 0, PAGE_SIZE, DMA_FROM_DEVICE); |
| if (!saa->top_dma) |
| return -ENOMEM; |
| saa->bottom_dma = dma_map_page(&dev->pci->dev, |
| virt_to_page(saa->bottom), |
| 0, PAGE_SIZE, DMA_FROM_DEVICE); |
| if (!saa->bottom_dma) { |
| dma_unmap_page(&dev->pci->dev, saa->top_dma, PAGE_SIZE, |
| DMA_FROM_DEVICE); |
| return -ENOMEM; |
| } |
| |
| saa_writel(SAA7134_VIDEO_PORT_CTRL0 >> 2, 0xA300B000); |
| saa_writel(SAA7134_VIDEO_PORT_CTRL4 >> 2, 0x40000200); |
| |
| /* Set HPI interface for video */ |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0xff); |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, HPI_ADDR_VIDEO_BUFFER); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_ADDR); |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0x00); |
| |
| /* Enable TS interface */ |
| saa_writeb(SAA7134_TS_PARALLEL, 0xe6); |
| |
| /* Reset TS interface */ |
| saa_setb(SAA7134_TS_SERIAL1, 0x01); |
| saa_clearb(SAA7134_TS_SERIAL1, 0x01); |
| |
| /* Set up transfer block size */ |
| saa_writeb(SAA7134_TS_PARALLEL_SERIAL, 128 - 1); |
| saa_writeb(SAA7134_TS_DMA0, (PAGE_SIZE >> 7) - 1); |
| saa_writeb(SAA7134_TS_DMA1, 0); |
| saa_writeb(SAA7134_TS_DMA2, 0); |
| |
| /* Enable video streaming mode */ |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_VIDEO); |
| |
| saa_writel(SAA7134_RS_BA1(5), cpu_to_le32(saa->top_dma)); |
| saa_writel(SAA7134_RS_BA2(5), cpu_to_le32(saa->bottom_dma)); |
| saa_writel(SAA7134_RS_PITCH(5), 128); |
| saa_writel(SAA7134_RS_CONTROL(5), SAA7134_RS_CONTROL_BURST_MAX); |
| |
| /* Enable TS FIFO */ |
| saa_setl(SAA7134_MAIN_CTRL, SAA7134_MAIN_CTRL_TE5); |
| |
| /* Enable DMA IRQ */ |
| saa_setl(SAA7134_IRQ1, |
| SAA7134_IRQ1_INTE_RA2_1 | SAA7134_IRQ1_INTE_RA2_0); |
| |
| return 0; |
| } |
| |
| static int saa7134_go7007_stream_stop(struct go7007 *go) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev; |
| |
| if (!saa) |
| return -EINVAL; |
| dev = saa->dev; |
| if (!dev) |
| return -EINVAL; |
| |
| /* Shut down TS FIFO */ |
| saa_clearl(SAA7134_MAIN_CTRL, SAA7134_MAIN_CTRL_TE5); |
| |
| /* Disable DMA IRQ */ |
| saa_clearl(SAA7134_IRQ1, |
| SAA7134_IRQ1_INTE_RA2_1 | SAA7134_IRQ1_INTE_RA2_0); |
| |
| /* Disable TS interface */ |
| saa_clearb(SAA7134_TS_PARALLEL, 0x80); |
| |
| dma_unmap_page(&dev->pci->dev, saa->top_dma, PAGE_SIZE, |
| DMA_FROM_DEVICE); |
| dma_unmap_page(&dev->pci->dev, saa->bottom_dma, PAGE_SIZE, |
| DMA_FROM_DEVICE); |
| |
| return 0; |
| } |
| |
| static int saa7134_go7007_send_firmware(struct go7007 *go, u8 *data, int len) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| u16 status_reg; |
| int i; |
| |
| #ifdef GO7007_HPI_DEBUG |
| printk(KERN_DEBUG "saa7134-go7007: DownloadBuffer " |
| "sending %d bytes\n", len); |
| #endif |
| |
| while (len > 0) { |
| i = len > 64 ? 64 : len; |
| saa_writeb(SAA7134_GPIO_GPMODE0, 0xff); |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, HPI_ADDR_INIT_BUFFER); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_ADDR); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| while (i-- > 0) { |
| saa_writeb(SAA7134_GPIO_GPSTATUS0, *data); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_WRITE); |
| saa_writeb(SAA7134_GPIO_GPSTATUS2, GPIO_COMMAND_IDLE); |
| ++data; |
| --len; |
| } |
| for (i = 0; i < 100; ++i) { |
| gpio_read(dev, HPI_ADDR_INTR_STATUS, &status_reg); |
| if (!(status_reg & 0x0002)) |
| break; |
| } |
| if (i == 100) { |
| printk(KERN_ERR "saa7134-go7007: device is hung, " |
| "status reg = 0x%04x\n", status_reg); |
| return -1; |
| } |
| } |
| return 0; |
| } |
| |
| static int saa7134_go7007_send_command(struct go7007 *go, unsigned int cmd, |
| void *arg) |
| { |
| struct saa7134_go7007 *saa = go->hpi_context; |
| struct saa7134_dev *dev = saa->dev; |
| |
| switch (cmd) { |
| case VIDIOC_S_STD: |
| { |
| v4l2_std_id *std = arg; |
| return saa7134_s_std_internal(dev, NULL, std); |
| } |
| case VIDIOC_G_STD: |
| { |
| v4l2_std_id *std = arg; |
| *std = dev->tvnorm->id; |
| return 0; |
| } |
| case VIDIOC_QUERYCTRL: |
| { |
| struct v4l2_queryctrl *ctrl = arg; |
| if (V4L2_CTRL_ID2CLASS(ctrl->id) == V4L2_CTRL_CLASS_USER) |
| return saa7134_queryctrl(NULL, NULL, ctrl); |
| } |
| case VIDIOC_G_CTRL: |
| { |
| struct v4l2_control *ctrl = arg; |
| if (V4L2_CTRL_ID2CLASS(ctrl->id) == V4L2_CTRL_CLASS_USER) |
| return saa7134_g_ctrl_internal(dev, NULL, ctrl); |
| } |
| case VIDIOC_S_CTRL: |
| { |
| struct v4l2_control *ctrl = arg; |
| if (V4L2_CTRL_ID2CLASS(ctrl->id) == V4L2_CTRL_CLASS_USER) |
| return saa7134_s_ctrl_internal(dev, NULL, ctrl); |
| } |
| } |
| return -EINVAL; |
| |
| } |
| |
| static struct go7007_hpi_ops saa7134_go7007_hpi_ops = { |
| .interface_reset = saa7134_go7007_interface_reset, |
| .write_interrupt = saa7134_go7007_write_interrupt, |
| .read_interrupt = saa7134_go7007_read_interrupt, |
| .stream_start = saa7134_go7007_stream_start, |
| .stream_stop = saa7134_go7007_stream_stop, |
| .send_firmware = saa7134_go7007_send_firmware, |
| .send_command = saa7134_go7007_send_command, |
| }; |
| |
| /********************* Add/remove functions *********************/ |
| |
| static int saa7134_go7007_init(struct saa7134_dev *dev) |
| { |
| struct go7007 *go; |
| struct saa7134_go7007 *saa; |
| |
| printk(KERN_DEBUG "saa7134-go7007: probing new SAA713X board\n"); |
| |
| saa = kmalloc(sizeof(struct saa7134_go7007), GFP_KERNEL); |
| if (saa == NULL) |
| return -ENOMEM; |
| memset(saa, 0, sizeof(struct saa7134_go7007)); |
| |
| /* Allocate a couple pages for receiving the compressed stream */ |
| saa->top = (u8 *)get_zeroed_page(GFP_KERNEL); |
| if (!saa->top) |
| goto allocfail; |
| saa->bottom = (u8 *)get_zeroed_page(GFP_KERNEL); |
| if (!saa->bottom) |
| goto allocfail; |
| |
| go = go7007_alloc(&board_voyager, &dev->pci->dev); |
| if (go == NULL) |
| goto allocfail; |
| go->board_id = GO7007_BOARDID_PCI_VOYAGER; |
| strncpy(go->name, saa7134_boards[dev->board].name, sizeof(go->name)); |
| go->hpi_ops = &saa7134_go7007_hpi_ops; |
| go->hpi_context = saa; |
| saa->dev = dev; |
| |
| /* Boot the GO7007 */ |
| if (go7007_boot_encoder(go, go->board_info->flags & |
| GO7007_BOARD_USE_ONBOARD_I2C) < 0) |
| goto initfail; |
| |
| /* Do any final GO7007 initialization, then register the |
| * V4L2 and ALSA interfaces */ |
| if (go7007_register_encoder(go) < 0) |
| goto initfail; |
| dev->empress_dev = go->video_dev; |
| video_set_drvdata(dev->empress_dev, go); |
| |
| go->status = STATUS_ONLINE; |
| return 0; |
| |
| initfail: |
| go->status = STATUS_SHUTDOWN; |
| return 0; |
| |
| allocfail: |
| if (saa->top) |
| free_page((unsigned long)saa->top); |
| if (saa->bottom) |
| free_page((unsigned long)saa->bottom); |
| kfree(saa); |
| return -ENOMEM; |
| } |
| |
| static int saa7134_go7007_fini(struct saa7134_dev *dev) |
| { |
| struct go7007 *go; |
| struct saa7134_go7007 *saa; |
| |
| if (NULL == dev->empress_dev) |
| return 0; |
| |
| go = video_get_drvdata(dev->empress_dev); |
| saa = go->hpi_context; |
| go->status = STATUS_SHUTDOWN; |
| free_page((unsigned long)saa->top); |
| free_page((unsigned long)saa->bottom); |
| kfree(saa); |
| go7007_remove(go); |
| dev->empress_dev = NULL; |
| |
| return 0; |
| } |
| |
| static struct saa7134_mpeg_ops saa7134_go7007_ops = { |
| .type = SAA7134_MPEG_GO7007, |
| .init = saa7134_go7007_init, |
| .fini = saa7134_go7007_fini, |
| .irq_ts_done = saa7134_go7007_irq_ts_done, |
| }; |
| |
| static int __init saa7134_go7007_mod_init(void) |
| { |
| return saa7134_ts_register(&saa7134_go7007_ops); |
| } |
| |
| static void __exit saa7134_go7007_mod_cleanup(void) |
| { |
| saa7134_ts_unregister(&saa7134_go7007_ops); |
| } |
| |
| module_init(saa7134_go7007_mod_init); |
| module_exit(saa7134_go7007_mod_cleanup); |
| |
| MODULE_LICENSE("GPL v2"); |