| Device tree binding for NVIDIA Tegra XUSB pad controller |
| ======================================================== |
| |
| The Tegra XUSB pad controller manages a set of I/O lanes (with differential |
| signals) which connect directly to pins/pads on the SoC package. Each lane |
| is controlled by a HW block referred to as a "pad" in the Tegra hardware |
| documentation. Each such "pad" may control either one or multiple lanes, |
| and thus contains any logic common to all its lanes. Each lane can be |
| separately configured and powered up. |
| |
| Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or |
| super-speed USB. Other lanes are for various types of low-speed, full-speed |
| or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller |
| contains a software-configurable mux that sits between the I/O controller |
| ports (e.g. PCIe) and the lanes. |
| |
| In addition to per-lane configuration, USB 3.0 ports may require additional |
| settings on a per-board basis. |
| |
| Pads will be represented as children of the top-level XUSB pad controller |
| device tree node. Each lane exposed by the pad will be represented by its |
| own subnode and can be referenced by users of the lane using the standard |
| PHY bindings, as described by the phy-bindings.txt file in this directory. |
| |
| The Tegra hardware documentation refers to the connection between the XUSB |
| pad controller and the XUSB controller as "ports". This is confusing since |
| "port" is typically used to denote the physical USB receptacle. The device |
| tree binding in this document uses the term "port" to refer to the logical |
| abstraction of the signals that are routed to a USB receptacle (i.e. a PHY |
| for the USB signal, the VBUS power supply, the USB 2.0 companion port for |
| USB 3.0 receptacles, ...). |
| |
| Required properties: |
| -------------------- |
| - compatible: Must be: |
| - Tegra124: "nvidia,tegra124-xusb-padctl" |
| - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl" |
| - Tegra210: "nvidia,tegra210-xusb-padctl" |
| - Tegra186: "nvidia,tegra186-xusb-padctl" |
| - reg: Physical base address and length of the controller's registers. |
| - resets: Must contain an entry for each entry in reset-names. |
| - reset-names: Must include the following entries: |
| - "padctl" |
| |
| For Tegra124: |
| - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. |
| - avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. |
| - avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. |
| - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. |
| |
| For Tegra210: |
| - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. |
| - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. |
| - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. |
| - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. |
| |
| For Tegra186: |
| - avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY |
| power supply. Must supply 1.8 V. |
| - avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply |
| 3.3 V. |
| - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V. |
| - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V. |
| |
| |
| Pad nodes: |
| ========== |
| |
| A required child node named "pads" contains a list of subnodes, one for each |
| of the pads exposed by the XUSB pad controller. Each pad may need additional |
| resources that can be referenced in its pad node. |
| |
| The "status" property is used to enable or disable the use of a pad. If set |
| to "disabled", the pad will not be used on the given board. In order to use |
| the pad and any of its lanes, this property must be set to "okay". |
| |
| For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie |
| and sata. No extra resources are required for operation of these pads. |
| |
| For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is |
| a description of the properties of each pad. |
| |
| UTMI pad: |
| --------- |
| |
| Required properties: |
| - clocks: Must contain an entry for each entry in clock-names. |
| - clock-names: Must contain the following entries: |
| - "trk": phandle and specifier referring to the USB2 tracking clock |
| |
| HSIC pad: |
| --------- |
| |
| Required properties: |
| - clocks: Must contain an entry for each entry in clock-names. |
| - clock-names: Must contain the following entries: |
| - "trk": phandle and specifier referring to the HSIC tracking clock |
| |
| PCIe pad: |
| --------- |
| |
| Required properties: |
| - clocks: Must contain an entry for each entry in clock-names. |
| - clock-names: Must contain the following entries: |
| - "pll": phandle and specifier referring to the PLLE |
| - resets: Must contain an entry for each entry in reset-names. |
| - reset-names: Must contain the following entries: |
| - "phy": reset for the PCIe UPHY block |
| |
| SATA pad: |
| --------- |
| |
| Required properties: |
| - resets: Must contain an entry for each entry in reset-names. |
| - reset-names: Must contain the following entries: |
| - "phy": reset for the SATA UPHY block |
| |
| |
| PHY nodes: |
| ========== |
| |
| Each pad node has a child named "lanes" that contains one or more children of |
| its own, each representing one of the lanes controlled by the pad. |
| |
| Required properties: |
| -------------------- |
| - status: Defines the operation status of the PHY. Valid values are: |
| - "disabled": the PHY is disabled |
| - "okay": the PHY is enabled |
| - #phy-cells: Should be 0. Since each lane represents a single PHY, there is |
| no need for an additional specifier. |
| - nvidia,function: The output function of the PHY. See below for a list of |
| valid functions per SoC generation. |
| |
| For Tegra124 and Tegra132, the list of valid PHY nodes is given below: |
| - usb2: usb2-0, usb2-1, usb2-2 |
| - functions: "snps", "xusb", "uart" |
| - ulpi: ulpi-0 |
| - functions: "snps", "xusb" |
| - hsic: hsic-0, hsic-1 |
| - functions: "snps", "xusb" |
| - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4 |
| - functions: "pcie", "usb3-ss" |
| - sata: sata-0 |
| - functions: "usb3-ss", "sata" |
| |
| For Tegra210, the list of valid PHY nodes is given below: |
| - usb2: usb2-0, usb2-1, usb2-2, usb2-3 |
| - functions: "snps", "xusb", "uart" |
| - hsic: hsic-0, hsic-1 |
| - functions: "snps", "xusb" |
| - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6 |
| - functions: "pcie-x1", "usb3-ss", "pcie-x4" |
| - sata: sata-0 |
| - functions: "usb3-ss", "sata" |
| |
| |
| Port nodes: |
| =========== |
| |
| A required child node named "ports" contains a list of all the ports exposed |
| by the XUSB pad controller. Per-port configuration is only required for USB. |
| |
| USB2 ports: |
| ----------- |
| |
| Required properties: |
| - status: Defines the operation status of the port. Valid values are: |
| - "disabled": the port is disabled |
| - "okay": the port is enabled |
| - mode: A string that determines the mode in which to run the port. Valid |
| values are: |
| - "host": for USB host mode |
| - "device": for USB device mode |
| - "otg": for USB OTG mode |
| |
| Optional properties: |
| - nvidia,internal: A boolean property whose presence determines that a port |
| is internal. In the absence of this property the port is considered to be |
| external. |
| - vbus-supply: phandle to a regulator supplying the VBUS voltage. |
| |
| ULPI ports: |
| ----------- |
| |
| Optional properties: |
| - status: Defines the operation status of the port. Valid values are: |
| - "disabled": the port is disabled |
| - "okay": the port is enabled |
| - nvidia,internal: A boolean property whose presence determines that a port |
| is internal. In the absence of this property the port is considered to be |
| external. |
| - vbus-supply: phandle to a regulator supplying the VBUS voltage. |
| |
| HSIC ports: |
| ----------- |
| |
| Required properties: |
| - status: Defines the operation status of the port. Valid values are: |
| - "disabled": the port is disabled |
| - "okay": the port is enabled |
| |
| Optional properties: |
| - vbus-supply: phandle to a regulator supplying the VBUS voltage. |
| |
| Super-speed USB ports: |
| ---------------------- |
| |
| Required properties: |
| - status: Defines the operation status of the port. Valid values are: |
| - "disabled": the port is disabled |
| - "okay": the port is enabled |
| - nvidia,usb2-companion: A single cell that specifies the physical port number |
| to map this super-speed USB port to. The range of valid port numbers varies |
| with the SoC generation: |
| - 0-2: for Tegra124 and Tegra132 |
| - 0-3: for Tegra210 |
| |
| Optional properties: |
| - nvidia,internal: A boolean property whose presence determines that a port |
| is internal. In the absence of this property the port is considered to be |
| external. |
| |
| For Tegra124 and Tegra132, the XUSB pad controller exposes the following |
| ports: |
| - 3x USB2: usb2-0, usb2-1, usb2-2 |
| - 1x ULPI: ulpi-0 |
| - 2x HSIC: hsic-0, hsic-1 |
| - 2x super-speed USB: usb3-0, usb3-1 |
| |
| For Tegra210, the XUSB pad controller exposes the following ports: |
| - 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 |
| - 2x HSIC: hsic-0, hsic-1 |
| - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 |
| |
| |
| Examples: |
| ========= |
| |
| Tegra124 and Tegra132: |
| ---------------------- |
| |
| SoC include: |
| |
| padctl@7009f000 { |
| /* for Tegra124 */ |
| compatible = "nvidia,tegra124-xusb-padctl"; |
| /* for Tegra132 */ |
| compatible = "nvidia,tegra132-xusb-padctl", |
| "nvidia,tegra124-xusb-padctl"; |
| reg = <0x0 0x7009f000 0x0 0x1000>; |
| resets = <&tegra_car 142>; |
| reset-names = "padctl"; |
| |
| pads { |
| usb2 { |
| status = "disabled"; |
| |
| lanes { |
| usb2-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| usb2-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| usb2-2 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| ulpi { |
| status = "disabled"; |
| |
| lanes { |
| ulpi-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| hsic { |
| status = "disabled"; |
| |
| lanes { |
| hsic-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| hsic-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| pcie { |
| status = "disabled"; |
| |
| lanes { |
| pcie-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-2 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-3 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-4 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| sata { |
| status = "disabled"; |
| |
| lanes { |
| sata-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| usb2-0 { |
| status = "disabled"; |
| }; |
| |
| usb2-1 { |
| status = "disabled"; |
| }; |
| |
| usb2-2 { |
| status = "disabled"; |
| }; |
| |
| ulpi-0 { |
| status = "disabled"; |
| }; |
| |
| hsic-0 { |
| status = "disabled"; |
| }; |
| |
| hsic-1 { |
| status = "disabled"; |
| }; |
| |
| usb3-0 { |
| status = "disabled"; |
| }; |
| |
| usb3-1 { |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| Board file: |
| |
| padctl@7009f000 { |
| status = "okay"; |
| |
| pads { |
| usb2 { |
| status = "okay"; |
| |
| lanes { |
| usb2-0 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| |
| usb2-1 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| |
| usb2-2 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| pcie { |
| status = "okay"; |
| |
| lanes { |
| pcie-0 { |
| nvidia,function = "usb3-ss"; |
| status = "okay"; |
| }; |
| |
| pcie-2 { |
| nvidia,function = "pcie"; |
| status = "okay"; |
| }; |
| |
| pcie-4 { |
| nvidia,function = "pcie"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| sata { |
| status = "okay"; |
| |
| lanes { |
| sata-0 { |
| nvidia,function = "sata"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| /* Micro A/B */ |
| usb2-0 { |
| status = "okay"; |
| mode = "otg"; |
| }; |
| |
| /* Mini PCIe */ |
| usb2-1 { |
| status = "okay"; |
| mode = "host"; |
| }; |
| |
| /* USB3 */ |
| usb2-2 { |
| status = "okay"; |
| mode = "host"; |
| |
| vbus-supply = <&vdd_usb3_vbus>; |
| }; |
| |
| usb3-0 { |
| nvidia,port = <2>; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| Tegra210: |
| --------- |
| |
| SoC include: |
| |
| padctl@7009f000 { |
| compatible = "nvidia,tegra210-xusb-padctl"; |
| reg = <0x0 0x7009f000 0x0 0x1000>; |
| resets = <&tegra_car 142>; |
| reset-names = "padctl"; |
| |
| status = "disabled"; |
| |
| pads { |
| usb2 { |
| clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; |
| clock-names = "trk"; |
| status = "disabled"; |
| |
| lanes { |
| usb2-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| usb2-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| usb2-2 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| usb2-3 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| hsic { |
| clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; |
| clock-names = "trk"; |
| status = "disabled"; |
| |
| lanes { |
| hsic-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| hsic-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| pcie { |
| clocks = <&tegra_car TEGRA210_CLK_PLL_E>; |
| clock-names = "pll"; |
| resets = <&tegra_car 205>; |
| reset-names = "phy"; |
| status = "disabled"; |
| |
| lanes { |
| pcie-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-1 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-2 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-3 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-4 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-5 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| |
| pcie-6 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| |
| sata { |
| clocks = <&tegra_car TEGRA210_CLK_PLL_E>; |
| clock-names = "pll"; |
| resets = <&tegra_car 204>; |
| reset-names = "phy"; |
| status = "disabled"; |
| |
| lanes { |
| sata-0 { |
| status = "disabled"; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| usb2-0 { |
| status = "disabled"; |
| }; |
| |
| usb2-1 { |
| status = "disabled"; |
| }; |
| |
| usb2-2 { |
| status = "disabled"; |
| }; |
| |
| usb2-3 { |
| status = "disabled"; |
| }; |
| |
| hsic-0 { |
| status = "disabled"; |
| }; |
| |
| hsic-1 { |
| status = "disabled"; |
| }; |
| |
| usb3-0 { |
| status = "disabled"; |
| }; |
| |
| usb3-1 { |
| status = "disabled"; |
| }; |
| |
| usb3-2 { |
| status = "disabled"; |
| }; |
| |
| usb3-3 { |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| Board file: |
| |
| padctl@7009f000 { |
| status = "okay"; |
| |
| pads { |
| usb2 { |
| status = "okay"; |
| |
| lanes { |
| usb2-0 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| |
| usb2-1 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| |
| usb2-2 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| |
| usb2-3 { |
| nvidia,function = "xusb"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| pcie { |
| status = "okay"; |
| |
| lanes { |
| pcie-0 { |
| nvidia,function = "pcie-x1"; |
| status = "okay"; |
| }; |
| |
| pcie-1 { |
| nvidia,function = "pcie-x4"; |
| status = "okay"; |
| }; |
| |
| pcie-2 { |
| nvidia,function = "pcie-x4"; |
| status = "okay"; |
| }; |
| |
| pcie-3 { |
| nvidia,function = "pcie-x4"; |
| status = "okay"; |
| }; |
| |
| pcie-4 { |
| nvidia,function = "pcie-x4"; |
| status = "okay"; |
| }; |
| |
| pcie-5 { |
| nvidia,function = "usb3-ss"; |
| status = "okay"; |
| }; |
| |
| pcie-6 { |
| nvidia,function = "usb3-ss"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| sata { |
| status = "okay"; |
| |
| lanes { |
| sata-0 { |
| nvidia,function = "sata"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| usb2-0 { |
| status = "okay"; |
| mode = "otg"; |
| }; |
| |
| usb2-1 { |
| status = "okay"; |
| vbus-supply = <&vdd_5v0_rtl>; |
| mode = "host"; |
| }; |
| |
| usb2-2 { |
| status = "okay"; |
| vbus-supply = <&vdd_usb_vbus>; |
| mode = "host"; |
| }; |
| |
| usb2-3 { |
| status = "okay"; |
| mode = "host"; |
| }; |
| |
| usb3-0 { |
| status = "okay"; |
| nvidia,lanes = "pcie-6"; |
| nvidia,port = <1>; |
| }; |
| |
| usb3-1 { |
| status = "okay"; |
| nvidia,lanes = "pcie-5"; |
| nvidia,port = <2>; |
| }; |
| }; |
| }; |