| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2015 MediaTek Inc. |
| * Author: Chunfeng Yun <chunfeng.yun@mediatek.com> |
| * |
| */ |
| |
| #include <dt-bindings/phy/phy.h> |
| #include <linux/clk.h> |
| #include <linux/debugfs.h> |
| #include <linux/delay.h> |
| #include <linux/iopoll.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/nvmem-consumer.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/phy/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| |
| #include "phy-mtk-io.h" |
| |
| /* version V1 sub-banks offset base address */ |
| /* banks shared by multiple phys */ |
| #define SSUSB_SIFSLV_V1_SPLLC 0x000 /* shared by u3 phys */ |
| #define SSUSB_SIFSLV_V1_U2FREQ 0x100 /* shared by u2 phys */ |
| #define SSUSB_SIFSLV_V1_CHIP 0x300 /* shared by u3 phys */ |
| /* u2 phy bank */ |
| #define SSUSB_SIFSLV_V1_U2PHY_COM 0x000 |
| /* u3/pcie/sata phy banks */ |
| #define SSUSB_SIFSLV_V1_U3PHYD 0x000 |
| #define SSUSB_SIFSLV_V1_U3PHYA 0x200 |
| |
| /* version V2/V3 sub-banks offset base address */ |
| /* V3: U2FREQ is not used anymore, but reserved */ |
| /* u2 phy banks */ |
| #define SSUSB_SIFSLV_V2_MISC 0x000 |
| #define SSUSB_SIFSLV_V2_U2FREQ 0x100 |
| #define SSUSB_SIFSLV_V2_U2PHY_COM 0x300 |
| /* u3/pcie/sata phy banks */ |
| #define SSUSB_SIFSLV_V2_SPLLC 0x000 |
| #define SSUSB_SIFSLV_V2_CHIP 0x100 |
| #define SSUSB_SIFSLV_V2_U3PHYD 0x200 |
| #define SSUSB_SIFSLV_V2_U3PHYA 0x400 |
| |
| #define U3P_MISC_REG1 0x04 |
| #define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) |
| |
| #define U3P_USBPHYACR0 0x000 |
| #define PA0_RG_U2PLL_FORCE_ON BIT(15) |
| #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) |
| #define PA0_RG_USB20_INTR_EN BIT(5) |
| |
| #define U3P_USBPHYACR1 0x004 |
| #define PA1_RG_INTR_CAL GENMASK(23, 19) |
| #define PA1_RG_VRT_SEL GENMASK(14, 12) |
| #define PA1_RG_TERM_SEL GENMASK(10, 8) |
| |
| #define U3P_USBPHYACR2 0x008 |
| #define PA2_RG_U2PLL_BW GENMASK(21, 19) |
| #define PA2_RG_SIF_U2PLL_FORCE_EN BIT(18) |
| |
| #define U3P_USBPHYACR5 0x014 |
| #define PA5_RG_U2_HSTX_SRCAL_EN BIT(15) |
| #define PA5_RG_U2_HSTX_SRCTRL GENMASK(14, 12) |
| #define PA5_RG_U2_HS_100U_U3_EN BIT(11) |
| |
| #define U3P_USBPHYACR6 0x018 |
| #define PA6_RG_U2_PRE_EMP GENMASK(31, 30) |
| #define PA6_RG_U2_BC11_SW_EN BIT(23) |
| #define PA6_RG_U2_OTG_VBUSCMP_EN BIT(20) |
| #define PA6_RG_U2_DISCTH GENMASK(7, 4) |
| #define PA6_RG_U2_SQTH GENMASK(3, 0) |
| |
| #define U3P_U2PHYACR4 0x020 |
| #define P2C_RG_USB20_GPIO_CTL BIT(9) |
| #define P2C_USB20_GPIO_MODE BIT(8) |
| #define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE) |
| |
| #define U3P_U2PHYA_RESV 0x030 |
| #define P2R_RG_U2PLL_FBDIV_26M 0x1bb13b |
| #define P2R_RG_U2PLL_FBDIV_48M 0x3c0000 |
| |
| #define U3P_U2PHYA_RESV1 0x044 |
| #define P2R_RG_U2PLL_REFCLK_SEL BIT(5) |
| #define P2R_RG_U2PLL_FRA_EN BIT(3) |
| |
| #define U3D_U2PHYDCR0 0x060 |
| #define P2C_RG_SIF_U2PLL_FORCE_ON BIT(24) |
| |
| #define U3P_U2PHYDTM0 0x068 |
| #define P2C_FORCE_UART_EN BIT(26) |
| #define P2C_FORCE_DATAIN BIT(23) |
| #define P2C_FORCE_DM_PULLDOWN BIT(21) |
| #define P2C_FORCE_DP_PULLDOWN BIT(20) |
| #define P2C_FORCE_XCVRSEL BIT(19) |
| #define P2C_FORCE_SUSPENDM BIT(18) |
| #define P2C_FORCE_TERMSEL BIT(17) |
| #define P2C_RG_DATAIN GENMASK(13, 10) |
| #define P2C_RG_DMPULLDOWN BIT(7) |
| #define P2C_RG_DPPULLDOWN BIT(6) |
| #define P2C_RG_XCVRSEL GENMASK(5, 4) |
| #define P2C_RG_SUSPENDM BIT(3) |
| #define P2C_RG_TERMSEL BIT(2) |
| #define P2C_DTM0_PART_MASK \ |
| (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \ |
| P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \ |
| P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \ |
| P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL) |
| |
| #define U3P_U2PHYDTM1 0x06C |
| #define P2C_RG_UART_EN BIT(16) |
| #define P2C_FORCE_IDDIG BIT(9) |
| #define P2C_RG_VBUSVALID BIT(5) |
| #define P2C_RG_SESSEND BIT(4) |
| #define P2C_RG_AVALID BIT(2) |
| #define P2C_RG_IDDIG BIT(1) |
| |
| #define U3P_U2PHYBC12C 0x080 |
| #define P2C_RG_CHGDT_EN BIT(0) |
| |
| #define U3P_U3_CHIP_GPIO_CTLD 0x0c |
| #define P3C_REG_IP_SW_RST BIT(31) |
| #define P3C_MCU_BUS_CK_GATE_EN BIT(30) |
| #define P3C_FORCE_IP_SW_RST BIT(29) |
| |
| #define U3P_U3_CHIP_GPIO_CTLE 0x10 |
| #define P3C_RG_SWRST_U3_PHYD BIT(25) |
| #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) |
| |
| #define U3P_U3_PHYA_REG0 0x000 |
| #define P3A_RG_IEXT_INTR GENMASK(15, 10) |
| #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) |
| |
| #define U3P_U3_PHYA_REG1 0x004 |
| #define P3A_RG_CLKDRV_AMP GENMASK(31, 29) |
| |
| #define U3P_U3_PHYA_REG6 0x018 |
| #define P3A_RG_TX_EIDLE_CM GENMASK(31, 28) |
| |
| #define U3P_U3_PHYA_REG9 0x024 |
| #define P3A_RG_RX_DAC_MUX GENMASK(5, 1) |
| |
| #define U3P_U3_PHYA_DA_REG0 0x100 |
| #define P3A_RG_XTAL_EXT_PE2H GENMASK(17, 16) |
| #define P3A_RG_XTAL_EXT_PE1H GENMASK(13, 12) |
| #define P3A_RG_XTAL_EXT_EN_U3 GENMASK(11, 10) |
| |
| #define U3P_U3_PHYA_DA_REG4 0x108 |
| #define P3A_RG_PLL_DIVEN_PE2H GENMASK(21, 19) |
| #define P3A_RG_PLL_BC_PE2H GENMASK(7, 6) |
| |
| #define U3P_U3_PHYA_DA_REG5 0x10c |
| #define P3A_RG_PLL_BR_PE2H GENMASK(29, 28) |
| #define P3A_RG_PLL_IC_PE2H GENMASK(15, 12) |
| |
| #define U3P_U3_PHYA_DA_REG6 0x110 |
| #define P3A_RG_PLL_IR_PE2H GENMASK(19, 16) |
| |
| #define U3P_U3_PHYA_DA_REG7 0x114 |
| #define P3A_RG_PLL_BP_PE2H GENMASK(19, 16) |
| |
| #define U3P_U3_PHYA_DA_REG20 0x13c |
| #define P3A_RG_PLL_DELTA1_PE2H GENMASK(31, 16) |
| |
| #define U3P_U3_PHYA_DA_REG25 0x148 |
| #define P3A_RG_PLL_DELTA_PE2H GENMASK(15, 0) |
| |
| #define U3P_U3_PHYD_LFPS1 0x00c |
| #define P3D_RG_FWAKE_TH GENMASK(21, 16) |
| |
| #define U3P_U3_PHYD_IMPCAL0 0x010 |
| #define P3D_RG_FORCE_TX_IMPEL BIT(31) |
| #define P3D_RG_TX_IMPEL GENMASK(28, 24) |
| |
| #define U3P_U3_PHYD_IMPCAL1 0x014 |
| #define P3D_RG_FORCE_RX_IMPEL BIT(31) |
| #define P3D_RG_RX_IMPEL GENMASK(28, 24) |
| |
| #define U3P_U3_PHYD_RSV 0x054 |
| #define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) |
| |
| #define U3P_U3_PHYD_CDR1 0x05c |
| #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) |
| #define P3D_RG_CDR_BIR_LTD0 GENMASK(12, 8) |
| |
| #define U3P_U3_PHYD_TOP1 0x100 |
| #define P3D_RG_PHY_MODE GENMASK(2, 1) |
| #define P3D_RG_FORCE_PHY_MODE BIT(0) |
| |
| #define U3P_U3_PHYD_RXDET1 0x128 |
| #define P3D_RG_RXDET_STB2_SET GENMASK(17, 9) |
| |
| #define U3P_U3_PHYD_RXDET2 0x12c |
| #define P3D_RG_RXDET_STB2_SET_P3 GENMASK(8, 0) |
| |
| #define U3P_SPLLC_XTALCTL3 0x018 |
| #define XC3_RG_U3_XTAL_RX_PWD BIT(9) |
| #define XC3_RG_U3_FRC_XTAL_RX_PWD BIT(8) |
| |
| #define U3P_U2FREQ_FMCR0 0x00 |
| #define P2F_RG_MONCLK_SEL GENMASK(27, 26) |
| #define P2F_RG_FREQDET_EN BIT(24) |
| #define P2F_RG_CYCLECNT GENMASK(23, 0) |
| |
| #define U3P_U2FREQ_VALUE 0x0c |
| |
| #define U3P_U2FREQ_FMMONR1 0x10 |
| #define P2F_USB_FM_VALID BIT(0) |
| #define P2F_RG_FRCK_EN BIT(8) |
| |
| #define U3P_REF_CLK 26 /* MHZ */ |
| #define U3P_SLEW_RATE_COEF 28 |
| #define U3P_SR_COEF_DIVISOR 1000 |
| #define U3P_FM_DET_CYCLE_CNT 1024 |
| |
| /* SATA register setting */ |
| #define PHYD_CTRL_SIGNAL_MODE4 0x1c |
| /* CDR Charge Pump P-path current adjustment */ |
| #define RG_CDR_BICLTD1_GEN1_MSK GENMASK(23, 20) |
| #define RG_CDR_BICLTD0_GEN1_MSK GENMASK(11, 8) |
| |
| #define PHYD_DESIGN_OPTION2 0x24 |
| /* Symbol lock count selection */ |
| #define RG_LOCK_CNT_SEL_MSK GENMASK(5, 4) |
| |
| #define PHYD_DESIGN_OPTION9 0x40 |
| /* COMWAK GAP width window */ |
| #define RG_TG_MAX_MSK GENMASK(20, 16) |
| /* COMINIT GAP width window */ |
| #define RG_T2_MAX_MSK GENMASK(13, 8) |
| /* COMWAK GAP width window */ |
| #define RG_TG_MIN_MSK GENMASK(7, 5) |
| /* COMINIT GAP width window */ |
| #define RG_T2_MIN_MSK GENMASK(4, 0) |
| |
| #define ANA_RG_CTRL_SIGNAL1 0x4c |
| /* TX driver tail current control for 0dB de-empahsis mdoe for Gen1 speed */ |
| #define RG_IDRV_0DB_GEN1_MSK GENMASK(13, 8) |
| |
| #define ANA_RG_CTRL_SIGNAL4 0x58 |
| #define RG_CDR_BICLTR_GEN1_MSK GENMASK(23, 20) |
| /* Loop filter R1 resistance adjustment for Gen1 speed */ |
| #define RG_CDR_BR_GEN2_MSK GENMASK(10, 8) |
| |
| #define ANA_RG_CTRL_SIGNAL6 0x60 |
| /* I-path capacitance adjustment for Gen1 */ |
| #define RG_CDR_BC_GEN1_MSK GENMASK(28, 24) |
| #define RG_CDR_BIRLTR_GEN1_MSK GENMASK(4, 0) |
| |
| #define ANA_EQ_EYE_CTRL_SIGNAL1 0x6c |
| /* RX Gen1 LEQ tuning step */ |
| #define RG_EQ_DLEQ_LFI_GEN1_MSK GENMASK(11, 8) |
| |
| #define ANA_EQ_EYE_CTRL_SIGNAL4 0xd8 |
| #define RG_CDR_BIRLTD0_GEN1_MSK GENMASK(20, 16) |
| |
| #define ANA_EQ_EYE_CTRL_SIGNAL5 0xdc |
| #define RG_CDR_BIRLTD0_GEN3_MSK GENMASK(4, 0) |
| |
| /* PHY switch between pcie/usb3/sgmii/sata */ |
| #define USB_PHY_SWITCH_CTRL 0x0 |
| #define RG_PHY_SW_TYPE GENMASK(3, 0) |
| #define RG_PHY_SW_PCIE 0x0 |
| #define RG_PHY_SW_USB3 0x1 |
| #define RG_PHY_SW_SGMII 0x2 |
| #define RG_PHY_SW_SATA 0x3 |
| |
| #define TPHY_CLKS_CNT 2 |
| |
| #define USER_BUF_LEN(count) min_t(size_t, 8, (count)) |
| |
| enum mtk_phy_version { |
| MTK_PHY_V1 = 1, |
| MTK_PHY_V2, |
| MTK_PHY_V3, |
| }; |
| |
| struct mtk_phy_pdata { |
| /* avoid RX sensitivity level degradation only for mt8173 */ |
| bool avoid_rx_sen_degradation; |
| /* |
| * workaround only for mt8195, HW fix it for others of V3, |
| * u2phy should use integer mode instead of fractional mode of |
| * 48M PLL, fix it by switching PLL to 26M from default 48M |
| */ |
| bool sw_pll_48m_to_26m; |
| /* |
| * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse, |
| * support sw way, also support it for v2/v3 optionally. |
| */ |
| bool sw_efuse_supported; |
| enum mtk_phy_version version; |
| }; |
| |
| struct u2phy_banks { |
| void __iomem *misc; |
| void __iomem *fmreg; |
| void __iomem *com; |
| }; |
| |
| struct u3phy_banks { |
| void __iomem *spllc; |
| void __iomem *chip; |
| void __iomem *phyd; /* include u3phyd_bank2 */ |
| void __iomem *phya; /* include u3phya_da */ |
| }; |
| |
| struct mtk_phy_instance { |
| struct phy *phy; |
| void __iomem *port_base; |
| union { |
| struct u2phy_banks u2_banks; |
| struct u3phy_banks u3_banks; |
| }; |
| struct clk_bulk_data clks[TPHY_CLKS_CNT]; |
| u32 index; |
| u32 type; |
| struct regmap *type_sw; |
| u32 type_sw_reg; |
| u32 type_sw_index; |
| u32 efuse_sw_en; |
| u32 efuse_intr; |
| u32 efuse_tx_imp; |
| u32 efuse_rx_imp; |
| int eye_src; |
| int eye_vrt; |
| int eye_term; |
| int intr; |
| int discth; |
| int pre_emphasis; |
| bool bc12_en; |
| bool type_force_mode; |
| }; |
| |
| struct mtk_tphy { |
| struct device *dev; |
| void __iomem *sif_base; /* only shared sif */ |
| const struct mtk_phy_pdata *pdata; |
| struct mtk_phy_instance **phys; |
| int nphys; |
| int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */ |
| int src_coef; /* coefficient for slew rate calibrate */ |
| }; |
| |
| #if IS_ENABLED(CONFIG_DEBUG_FS) |
| |
| enum u2_phy_params { |
| U2P_EYE_VRT = 0, |
| U2P_EYE_TERM, |
| U2P_EFUSE_EN, |
| U2P_EFUSE_INTR, |
| U2P_DISCTH, |
| U2P_PRE_EMPHASIS, |
| }; |
| |
| enum u3_phy_params { |
| U3P_EFUSE_EN = 0, |
| U3P_EFUSE_INTR, |
| U3P_EFUSE_TX_IMP, |
| U3P_EFUSE_RX_IMP, |
| }; |
| |
| static const char *const u2_phy_files[] = { |
| [U2P_EYE_VRT] = "vrt", |
| [U2P_EYE_TERM] = "term", |
| [U2P_EFUSE_EN] = "efuse", |
| [U2P_EFUSE_INTR] = "intr", |
| [U2P_DISCTH] = "discth", |
| [U2P_PRE_EMPHASIS] = "preemph", |
| }; |
| |
| static const char *const u3_phy_files[] = { |
| [U3P_EFUSE_EN] = "efuse", |
| [U3P_EFUSE_INTR] = "intr", |
| [U3P_EFUSE_TX_IMP] = "tx-imp", |
| [U3P_EFUSE_RX_IMP] = "rx-imp", |
| }; |
| |
| static int u2_phy_params_show(struct seq_file *sf, void *unused) |
| { |
| struct mtk_phy_instance *inst = sf->private; |
| const char *fname = file_dentry(sf->file)->d_iname; |
| struct u2phy_banks *u2_banks = &inst->u2_banks; |
| void __iomem *com = u2_banks->com; |
| u32 max = 0; |
| u32 tmp = 0; |
| u32 val = 0; |
| int ret; |
| |
| ret = match_string(u2_phy_files, ARRAY_SIZE(u2_phy_files), fname); |
| if (ret < 0) |
| return ret; |
| |
| switch (ret) { |
| case U2P_EYE_VRT: |
| tmp = readl(com + U3P_USBPHYACR1); |
| val = FIELD_GET(PA1_RG_VRT_SEL, tmp); |
| max = FIELD_MAX(PA1_RG_VRT_SEL); |
| break; |
| |
| case U2P_EYE_TERM: |
| tmp = readl(com + U3P_USBPHYACR1); |
| val = FIELD_GET(PA1_RG_TERM_SEL, tmp); |
| max = FIELD_MAX(PA1_RG_TERM_SEL); |
| break; |
| |
| case U2P_EFUSE_EN: |
| if (u2_banks->misc) { |
| tmp = readl(u2_banks->misc + U3P_MISC_REG1); |
| max = 1; |
| } |
| |
| val = !!(tmp & MR1_EFUSE_AUTO_LOAD_DIS); |
| break; |
| |
| case U2P_EFUSE_INTR: |
| tmp = readl(com + U3P_USBPHYACR1); |
| val = FIELD_GET(PA1_RG_INTR_CAL, tmp); |
| max = FIELD_MAX(PA1_RG_INTR_CAL); |
| break; |
| |
| case U2P_DISCTH: |
| tmp = readl(com + U3P_USBPHYACR6); |
| val = FIELD_GET(PA6_RG_U2_DISCTH, tmp); |
| max = FIELD_MAX(PA6_RG_U2_DISCTH); |
| break; |
| |
| case U2P_PRE_EMPHASIS: |
| tmp = readl(com + U3P_USBPHYACR6); |
| val = FIELD_GET(PA6_RG_U2_PRE_EMP, tmp); |
| max = FIELD_MAX(PA6_RG_U2_PRE_EMP); |
| break; |
| |
| default: |
| seq_printf(sf, "invalid, %d\n", ret); |
| break; |
| } |
| |
| seq_printf(sf, "%s : %d [0, %d]\n", fname, val, max); |
| |
| return 0; |
| } |
| |
| static int u2_phy_params_open(struct inode *inode, struct file *file) |
| { |
| return single_open(file, u2_phy_params_show, inode->i_private); |
| } |
| |
| static ssize_t u2_phy_params_write(struct file *file, const char __user *ubuf, |
| size_t count, loff_t *ppos) |
| { |
| const char *fname = file_dentry(file)->d_iname; |
| struct seq_file *sf = file->private_data; |
| struct mtk_phy_instance *inst = sf->private; |
| struct u2phy_banks *u2_banks = &inst->u2_banks; |
| void __iomem *com = u2_banks->com; |
| ssize_t rc; |
| u32 val; |
| int ret; |
| |
| rc = kstrtouint_from_user(ubuf, USER_BUF_LEN(count), 0, &val); |
| if (rc) |
| return rc; |
| |
| ret = match_string(u2_phy_files, ARRAY_SIZE(u2_phy_files), fname); |
| if (ret < 0) |
| return (ssize_t)ret; |
| |
| switch (ret) { |
| case U2P_EYE_VRT: |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL, val); |
| break; |
| |
| case U2P_EYE_TERM: |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL, val); |
| break; |
| |
| case U2P_EFUSE_EN: |
| if (u2_banks->misc) |
| mtk_phy_update_field(u2_banks->misc + U3P_MISC_REG1, |
| MR1_EFUSE_AUTO_LOAD_DIS, !!val); |
| break; |
| |
| case U2P_EFUSE_INTR: |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL, val); |
| break; |
| |
| case U2P_DISCTH: |
| mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH, val); |
| break; |
| |
| case U2P_PRE_EMPHASIS: |
| mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_PRE_EMP, val); |
| break; |
| |
| default: |
| break; |
| } |
| |
| return count; |
| } |
| |
| static const struct file_operations u2_phy_fops = { |
| .open = u2_phy_params_open, |
| .write = u2_phy_params_write, |
| .read = seq_read, |
| .llseek = seq_lseek, |
| .release = single_release, |
| }; |
| |
| static void u2_phy_dbgfs_files_create(struct mtk_phy_instance *inst) |
| { |
| u32 count = ARRAY_SIZE(u2_phy_files); |
| int i; |
| |
| for (i = 0; i < count; i++) |
| debugfs_create_file(u2_phy_files[i], 0644, inst->phy->debugfs, |
| inst, &u2_phy_fops); |
| } |
| |
| static int u3_phy_params_show(struct seq_file *sf, void *unused) |
| { |
| struct mtk_phy_instance *inst = sf->private; |
| const char *fname = file_dentry(sf->file)->d_iname; |
| struct u3phy_banks *u3_banks = &inst->u3_banks; |
| u32 val = 0; |
| u32 max = 0; |
| u32 tmp; |
| int ret; |
| |
| ret = match_string(u3_phy_files, ARRAY_SIZE(u3_phy_files), fname); |
| if (ret < 0) |
| return ret; |
| |
| switch (ret) { |
| case U3P_EFUSE_EN: |
| tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); |
| val = !!(tmp & P3D_RG_EFUSE_AUTO_LOAD_DIS); |
| max = 1; |
| break; |
| |
| case U3P_EFUSE_INTR: |
| tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0); |
| val = FIELD_GET(P3A_RG_IEXT_INTR, tmp); |
| max = FIELD_MAX(P3A_RG_IEXT_INTR); |
| break; |
| |
| case U3P_EFUSE_TX_IMP: |
| tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0); |
| val = FIELD_GET(P3D_RG_TX_IMPEL, tmp); |
| max = FIELD_MAX(P3D_RG_TX_IMPEL); |
| break; |
| |
| case U3P_EFUSE_RX_IMP: |
| tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1); |
| val = FIELD_GET(P3D_RG_RX_IMPEL, tmp); |
| max = FIELD_MAX(P3D_RG_RX_IMPEL); |
| break; |
| |
| default: |
| seq_printf(sf, "invalid, %d\n", ret); |
| break; |
| } |
| |
| seq_printf(sf, "%s : %d [0, %d]\n", fname, val, max); |
| |
| return 0; |
| } |
| |
| static int u3_phy_params_open(struct inode *inode, struct file *file) |
| { |
| return single_open(file, u3_phy_params_show, inode->i_private); |
| } |
| |
| static ssize_t u3_phy_params_write(struct file *file, const char __user *ubuf, |
| size_t count, loff_t *ppos) |
| { |
| const char *fname = file_dentry(file)->d_iname; |
| struct seq_file *sf = file->private_data; |
| struct mtk_phy_instance *inst = sf->private; |
| struct u3phy_banks *u3_banks = &inst->u3_banks; |
| void __iomem *phyd = u3_banks->phyd; |
| ssize_t rc; |
| u32 val; |
| int ret; |
| |
| rc = kstrtouint_from_user(ubuf, USER_BUF_LEN(count), 0, &val); |
| if (rc) |
| return rc; |
| |
| ret = match_string(u3_phy_files, ARRAY_SIZE(u3_phy_files), fname); |
| if (ret < 0) |
| return (ssize_t)ret; |
| |
| switch (ret) { |
| case U3P_EFUSE_EN: |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_RSV, |
| P3D_RG_EFUSE_AUTO_LOAD_DIS, !!val); |
| break; |
| |
| case U3P_EFUSE_INTR: |
| mtk_phy_update_field(u3_banks->phya + U3P_U3_PHYA_REG0, |
| P3A_RG_IEXT_INTR, val); |
| break; |
| |
| case U3P_EFUSE_TX_IMP: |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL, val); |
| mtk_phy_set_bits(phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL); |
| break; |
| |
| case U3P_EFUSE_RX_IMP: |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL, val); |
| mtk_phy_set_bits(phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL); |
| break; |
| |
| default: |
| break; |
| } |
| |
| return count; |
| } |
| |
| static const struct file_operations u3_phy_fops = { |
| .open = u3_phy_params_open, |
| .write = u3_phy_params_write, |
| .read = seq_read, |
| .llseek = seq_lseek, |
| .release = single_release, |
| }; |
| |
| static void u3_phy_dbgfs_files_create(struct mtk_phy_instance *inst) |
| { |
| u32 count = ARRAY_SIZE(u3_phy_files); |
| int i; |
| |
| for (i = 0; i < count; i++) |
| debugfs_create_file(u3_phy_files[i], 0644, inst->phy->debugfs, |
| inst, &u3_phy_fops); |
| } |
| |
| static int phy_type_show(struct seq_file *sf, void *unused) |
| { |
| struct mtk_phy_instance *inst = sf->private; |
| const char *type; |
| |
| switch (inst->type) { |
| case PHY_TYPE_USB2: |
| type = "USB2"; |
| break; |
| case PHY_TYPE_USB3: |
| type = "USB3"; |
| break; |
| case PHY_TYPE_PCIE: |
| type = "PCIe"; |
| break; |
| case PHY_TYPE_SGMII: |
| type = "SGMII"; |
| break; |
| case PHY_TYPE_SATA: |
| type = "SATA"; |
| break; |
| default: |
| type = ""; |
| } |
| |
| seq_printf(sf, "%s\n", type); |
| |
| return 0; |
| } |
| DEFINE_SHOW_ATTRIBUTE(phy_type); |
| |
| /* these files will be removed when phy is released by phy core */ |
| static void phy_debugfs_init(struct mtk_phy_instance *inst) |
| { |
| debugfs_create_file("type", 0444, inst->phy->debugfs, inst, &phy_type_fops); |
| |
| switch (inst->type) { |
| case PHY_TYPE_USB2: |
| u2_phy_dbgfs_files_create(inst); |
| break; |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_PCIE: |
| u3_phy_dbgfs_files_create(inst); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| #else |
| |
| static void phy_debugfs_init(struct mtk_phy_instance *inst) |
| {} |
| |
| #endif |
| |
| static void hs_slew_rate_calibrate(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *fmreg = u2_banks->fmreg; |
| void __iomem *com = u2_banks->com; |
| int calibration_val; |
| int fm_out; |
| u32 tmp; |
| |
| /* HW V3 doesn't support slew rate cal anymore */ |
| if (tphy->pdata->version == MTK_PHY_V3) |
| return; |
| |
| /* use force value */ |
| if (instance->eye_src) |
| return; |
| |
| /* enable USB ring oscillator */ |
| mtk_phy_set_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN); |
| udelay(1); |
| |
| /*enable free run clock */ |
| mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN); |
| |
| /* set cycle count as 1024, and select u2 channel */ |
| tmp = readl(fmreg + U3P_U2FREQ_FMCR0); |
| tmp &= ~(P2F_RG_CYCLECNT | P2F_RG_MONCLK_SEL); |
| tmp |= FIELD_PREP(P2F_RG_CYCLECNT, U3P_FM_DET_CYCLE_CNT); |
| if (tphy->pdata->version == MTK_PHY_V1) |
| tmp |= FIELD_PREP(P2F_RG_MONCLK_SEL, instance->index >> 1); |
| |
| writel(tmp, fmreg + U3P_U2FREQ_FMCR0); |
| |
| /* enable frequency meter */ |
| mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN); |
| |
| /* ignore return value */ |
| readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp, |
| (tmp & P2F_USB_FM_VALID), 10, 200); |
| |
| fm_out = readl(fmreg + U3P_U2FREQ_VALUE); |
| |
| /* disable frequency meter */ |
| mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN); |
| |
| /*disable free run clock */ |
| mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN); |
| |
| if (fm_out) { |
| /* ( 1024 / FM_OUT ) x reference clock frequency x coef */ |
| tmp = tphy->src_ref_clk * tphy->src_coef; |
| tmp = (tmp * U3P_FM_DET_CYCLE_CNT) / fm_out; |
| calibration_val = DIV_ROUND_CLOSEST(tmp, U3P_SR_COEF_DIVISOR); |
| } else { |
| /* if FM detection fail, set default value */ |
| calibration_val = 4; |
| } |
| dev_dbg(tphy->dev, "phy:%d, fm_out:%d, calib:%d (clk:%d, coef:%d)\n", |
| instance->index, fm_out, calibration_val, |
| tphy->src_ref_clk, tphy->src_coef); |
| |
| /* set HS slew rate */ |
| mtk_phy_update_field(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL, |
| calibration_val); |
| |
| /* disable USB ring oscillator */ |
| mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN); |
| } |
| |
| static void u3_phy_instance_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| void __iomem *phya = u3_banks->phya; |
| void __iomem *phyd = u3_banks->phyd; |
| |
| if (instance->type_force_mode) { |
| /* force phy as usb mode, default is pcie rc mode */ |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_TOP1, P3D_RG_PHY_MODE, 1); |
| mtk_phy_set_bits(phyd + U3P_U3_PHYD_TOP1, P3D_RG_FORCE_PHY_MODE); |
| /* power down phy by ip and pipe reset */ |
| mtk_phy_set_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLD, |
| P3C_FORCE_IP_SW_RST | P3C_MCU_BUS_CK_GATE_EN); |
| mtk_phy_set_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLE, |
| P3C_RG_SWRST_U3_PHYD | P3C_RG_SWRST_U3_PHYD_FORCE_EN); |
| udelay(10); |
| /* power on phy again */ |
| mtk_phy_clear_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLD, |
| P3C_FORCE_IP_SW_RST | P3C_MCU_BUS_CK_GATE_EN); |
| mtk_phy_clear_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLE, |
| P3C_RG_SWRST_U3_PHYD | P3C_RG_SWRST_U3_PHYD_FORCE_EN); |
| } |
| |
| /* gating PCIe Analog XTAL clock */ |
| mtk_phy_set_bits(u3_banks->spllc + U3P_SPLLC_XTALCTL3, |
| XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD); |
| |
| /* gating XSQ */ |
| mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG0, P3A_RG_XTAL_EXT_EN_U3, 2); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_REG9, P3A_RG_RX_DAC_MUX, 4); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_REG6, P3A_RG_TX_EIDLE_CM, 0xe); |
| |
| mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_CDR1, |
| P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1, |
| FIELD_PREP(P3D_RG_CDR_BIR_LTD0, 0xc) | |
| FIELD_PREP(P3D_RG_CDR_BIR_LTD1, 0x3)); |
| |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_LFPS1, P3D_RG_FWAKE_TH, 0x34); |
| |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_RXDET1, P3D_RG_RXDET_STB2_SET, 0x10); |
| |
| mtk_phy_update_field(phyd + U3P_U3_PHYD_RXDET2, P3D_RG_RXDET_STB2_SET_P3, 0x10); |
| |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index); |
| } |
| |
| static void u2_phy_pll_26m_set(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| |
| if (!tphy->pdata->sw_pll_48m_to_26m) |
| return; |
| |
| mtk_phy_update_field(com + U3P_USBPHYACR0, PA0_USB20_PLL_PREDIV, 0); |
| |
| mtk_phy_update_field(com + U3P_USBPHYACR2, PA2_RG_U2PLL_BW, 3); |
| |
| writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV); |
| |
| mtk_phy_set_bits(com + U3P_U2PHYA_RESV1, |
| P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL); |
| } |
| |
| static void u2_phy_instance_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| u32 index = instance->index; |
| |
| /* switch to USB function, and enable usb pll */ |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM0, |
| P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_UART_EN); |
| |
| mtk_phy_set_bits(com + U3P_USBPHYACR0, PA0_RG_USB20_INTR_EN); |
| |
| /* disable switch 100uA current to SSUSB */ |
| mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK); |
| |
| if (tphy->pdata->avoid_rx_sen_degradation) { |
| if (!index) { |
| mtk_phy_set_bits(com + U3P_USBPHYACR2, PA2_RG_SIF_U2PLL_FORCE_EN); |
| |
| mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON); |
| } else { |
| mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON); |
| |
| mtk_phy_set_bits(com + U3P_U2PHYDTM0, |
| P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM); |
| } |
| } |
| |
| /* DP/DM BC1.1 path Disable */ |
| mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN); |
| |
| mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_SQTH, 2); |
| |
| /* Workaround only for mt8195, HW fix it for others (V3) */ |
| u2_phy_pll_26m_set(tphy, instance); |
| |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, index); |
| } |
| |
| static void u2_phy_instance_power_on(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| u32 index = instance->index; |
| |
| /* OTG Enable */ |
| mtk_phy_set_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN); |
| |
| mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND); |
| |
| if (tphy->pdata->avoid_rx_sen_degradation && index) { |
| mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON); |
| |
| mtk_phy_set_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM); |
| } |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, index); |
| } |
| |
| static void u2_phy_instance_power_off(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| u32 index = instance->index; |
| |
| /* OTG Disable */ |
| mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID); |
| |
| mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND); |
| |
| if (tphy->pdata->avoid_rx_sen_degradation && index) { |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM); |
| |
| mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON); |
| } |
| |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, index); |
| } |
| |
| static void u2_phy_instance_exit(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| u32 index = instance->index; |
| |
| if (tphy->pdata->avoid_rx_sen_degradation && index) { |
| mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON); |
| |
| mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM); |
| } |
| } |
| |
| static void u2_phy_instance_set_mode(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance, |
| enum phy_mode mode) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| u32 tmp; |
| |
| tmp = readl(u2_banks->com + U3P_U2PHYDTM1); |
| switch (mode) { |
| case PHY_MODE_USB_DEVICE: |
| tmp |= P2C_FORCE_IDDIG | P2C_RG_IDDIG; |
| break; |
| case PHY_MODE_USB_HOST: |
| tmp |= P2C_FORCE_IDDIG; |
| tmp &= ~P2C_RG_IDDIG; |
| break; |
| case PHY_MODE_USB_OTG: |
| tmp &= ~(P2C_FORCE_IDDIG | P2C_RG_IDDIG); |
| break; |
| default: |
| return; |
| } |
| writel(tmp, u2_banks->com + U3P_U2PHYDTM1); |
| } |
| |
| static void pcie_phy_instance_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| void __iomem *phya = u3_banks->phya; |
| |
| if (tphy->pdata->version != MTK_PHY_V1) |
| return; |
| |
| mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG0, |
| P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H, |
| FIELD_PREP(P3A_RG_XTAL_EXT_PE1H, 0x2) | |
| FIELD_PREP(P3A_RG_XTAL_EXT_PE2H, 0x2)); |
| |
| /* ref clk drive */ |
| mtk_phy_update_field(phya + U3P_U3_PHYA_REG1, P3A_RG_CLKDRV_AMP, 0x4); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_REG0, P3A_RG_CLKDRV_OFF, 0x1); |
| |
| /* SSC delta -5000ppm */ |
| mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG20, P3A_RG_PLL_DELTA1_PE2H, 0x3c); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG25, P3A_RG_PLL_DELTA_PE2H, 0x36); |
| |
| /* change pll BW 0.6M */ |
| mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG5, |
| P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H, |
| FIELD_PREP(P3A_RG_PLL_BR_PE2H, 0x1) | |
| FIELD_PREP(P3A_RG_PLL_IC_PE2H, 0x1)); |
| |
| mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG4, |
| P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H, |
| FIELD_PREP(P3A_RG_PLL_BC_PE2H, 0x3)); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG6, P3A_RG_PLL_IR_PE2H, 0x2); |
| |
| mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG7, P3A_RG_PLL_BP_PE2H, 0xa); |
| |
| /* Tx Detect Rx Timing: 10us -> 5us */ |
| mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_RXDET1, |
| P3D_RG_RXDET_STB2_SET, 0x10); |
| |
| mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_RXDET2, |
| P3D_RG_RXDET_STB2_SET_P3, 0x10); |
| |
| /* wait for PCIe subsys register to active */ |
| usleep_range(2500, 3000); |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index); |
| } |
| |
| static void pcie_phy_instance_power_on(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u3phy_banks *bank = &instance->u3_banks; |
| |
| mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD, |
| P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST); |
| |
| mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE, |
| P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD); |
| } |
| |
| static void pcie_phy_instance_power_off(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| |
| { |
| struct u3phy_banks *bank = &instance->u3_banks; |
| |
| mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD, |
| P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST); |
| |
| mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE, |
| P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD); |
| } |
| |
| static void sata_phy_instance_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| void __iomem *phyd = u3_banks->phyd; |
| |
| /* charge current adjustment */ |
| mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL6, |
| RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK, |
| FIELD_PREP(RG_CDR_BIRLTR_GEN1_MSK, 0x6) | |
| FIELD_PREP(RG_CDR_BC_GEN1_MSK, 0x1a)); |
| |
| mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL4, RG_CDR_BIRLTD0_GEN1_MSK, 0x18); |
| |
| mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL5, RG_CDR_BIRLTD0_GEN3_MSK, 0x06); |
| |
| mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL4, |
| RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK, |
| FIELD_PREP(RG_CDR_BICLTR_GEN1_MSK, 0x0c) | |
| FIELD_PREP(RG_CDR_BR_GEN2_MSK, 0x07)); |
| |
| mtk_phy_update_bits(phyd + PHYD_CTRL_SIGNAL_MODE4, |
| RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK, |
| FIELD_PREP(RG_CDR_BICLTD0_GEN1_MSK, 0x08) | |
| FIELD_PREP(RG_CDR_BICLTD1_GEN1_MSK, 0x02)); |
| |
| mtk_phy_update_field(phyd + PHYD_DESIGN_OPTION2, RG_LOCK_CNT_SEL_MSK, 0x02); |
| |
| mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9, |
| RG_T2_MIN_MSK | RG_TG_MIN_MSK, |
| FIELD_PREP(RG_T2_MIN_MSK, 0x12) | |
| FIELD_PREP(RG_TG_MIN_MSK, 0x04)); |
| |
| mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9, |
| RG_T2_MAX_MSK | RG_TG_MAX_MSK, |
| FIELD_PREP(RG_T2_MAX_MSK, 0x31) | |
| FIELD_PREP(RG_TG_MAX_MSK, 0x0e)); |
| |
| mtk_phy_update_field(phyd + ANA_RG_CTRL_SIGNAL1, RG_IDRV_0DB_GEN1_MSK, 0x20); |
| |
| mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL1, RG_EQ_DLEQ_LFI_GEN1_MSK, 0x03); |
| |
| dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index); |
| } |
| |
| static void phy_v1_banks_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB2: |
| u2_banks->misc = NULL; |
| u2_banks->fmreg = tphy->sif_base + SSUSB_SIFSLV_V1_U2FREQ; |
| u2_banks->com = instance->port_base + SSUSB_SIFSLV_V1_U2PHY_COM; |
| break; |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_PCIE: |
| u3_banks->spllc = tphy->sif_base + SSUSB_SIFSLV_V1_SPLLC; |
| u3_banks->chip = tphy->sif_base + SSUSB_SIFSLV_V1_CHIP; |
| u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD; |
| u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA; |
| break; |
| case PHY_TYPE_SATA: |
| u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD; |
| break; |
| default: |
| dev_err(tphy->dev, "incompatible PHY type\n"); |
| return; |
| } |
| } |
| |
| static void phy_v2_banks_init(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB2: |
| u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC; |
| u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ; |
| u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM; |
| break; |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_PCIE: |
| u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC; |
| u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP; |
| u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD; |
| u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA; |
| break; |
| default: |
| dev_err(tphy->dev, "incompatible PHY type\n"); |
| return; |
| } |
| } |
| |
| static void phy_parse_property(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct device *dev = &instance->phy->dev; |
| |
| if (instance->type == PHY_TYPE_USB3) |
| instance->type_force_mode = device_property_read_bool(dev, "mediatek,force-mode"); |
| |
| if (instance->type != PHY_TYPE_USB2) |
| return; |
| |
| instance->bc12_en = device_property_read_bool(dev, "mediatek,bc12"); |
| device_property_read_u32(dev, "mediatek,eye-src", |
| &instance->eye_src); |
| device_property_read_u32(dev, "mediatek,eye-vrt", |
| &instance->eye_vrt); |
| device_property_read_u32(dev, "mediatek,eye-term", |
| &instance->eye_term); |
| device_property_read_u32(dev, "mediatek,intr", |
| &instance->intr); |
| device_property_read_u32(dev, "mediatek,discth", |
| &instance->discth); |
| device_property_read_u32(dev, "mediatek,pre-emphasis", |
| &instance->pre_emphasis); |
| dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d, intr:%d, disc:%d\n", |
| instance->bc12_en, instance->eye_src, |
| instance->eye_vrt, instance->eye_term, |
| instance->intr, instance->discth); |
| dev_dbg(dev, "pre-emp:%d\n", instance->pre_emphasis); |
| } |
| |
| static void u2_phy_props_set(struct mtk_tphy *tphy, |
| struct mtk_phy_instance *instance) |
| { |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| void __iomem *com = u2_banks->com; |
| |
| if (instance->bc12_en) /* BC1.2 path Enable */ |
| mtk_phy_set_bits(com + U3P_U2PHYBC12C, P2C_RG_CHGDT_EN); |
| |
| if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) |
| mtk_phy_update_field(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL, |
| instance->eye_src); |
| |
| if (instance->eye_vrt) |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL, |
| instance->eye_vrt); |
| |
| if (instance->eye_term) |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL, |
| instance->eye_term); |
| |
| if (instance->intr) { |
| if (u2_banks->misc) |
| mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1, |
| MR1_EFUSE_AUTO_LOAD_DIS); |
| |
| mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL, |
| instance->intr); |
| } |
| |
| if (instance->discth) |
| mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH, |
| instance->discth); |
| |
| if (instance->pre_emphasis) |
| mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_PRE_EMP, |
| instance->pre_emphasis); |
| } |
| |
| /* type switch for usb3/pcie/sgmii/sata */ |
| static int phy_type_syscon_get(struct mtk_phy_instance *instance, |
| struct device_node *dn) |
| { |
| struct of_phandle_args args; |
| int ret; |
| |
| /* type switch function is optional */ |
| if (!of_property_read_bool(dn, "mediatek,syscon-type")) |
| return 0; |
| |
| ret = of_parse_phandle_with_fixed_args(dn, "mediatek,syscon-type", |
| 2, 0, &args); |
| if (ret) |
| return ret; |
| |
| instance->type_sw_reg = args.args[0]; |
| instance->type_sw_index = args.args[1] & 0x3; /* <=3 */ |
| instance->type_sw = syscon_node_to_regmap(args.np); |
| of_node_put(args.np); |
| dev_info(&instance->phy->dev, "type_sw - reg %#x, index %d\n", |
| instance->type_sw_reg, instance->type_sw_index); |
| |
| return PTR_ERR_OR_ZERO(instance->type_sw); |
| } |
| |
| static int phy_type_set(struct mtk_phy_instance *instance) |
| { |
| int type; |
| u32 offset; |
| |
| if (!instance->type_sw) |
| return 0; |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB3: |
| type = RG_PHY_SW_USB3; |
| break; |
| case PHY_TYPE_PCIE: |
| type = RG_PHY_SW_PCIE; |
| break; |
| case PHY_TYPE_SGMII: |
| type = RG_PHY_SW_SGMII; |
| break; |
| case PHY_TYPE_SATA: |
| type = RG_PHY_SW_SATA; |
| break; |
| case PHY_TYPE_USB2: |
| default: |
| return 0; |
| } |
| |
| offset = instance->type_sw_index * BITS_PER_BYTE; |
| regmap_update_bits(instance->type_sw, instance->type_sw_reg, |
| RG_PHY_SW_TYPE << offset, type << offset); |
| |
| return 0; |
| } |
| |
| static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance) |
| { |
| struct device *dev = &instance->phy->dev; |
| int ret = 0; |
| |
| /* tphy v1 doesn't support sw efuse, skip it */ |
| if (!tphy->pdata->sw_efuse_supported) { |
| instance->efuse_sw_en = 0; |
| return 0; |
| } |
| |
| /* software efuse is optional */ |
| instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells"); |
| if (!instance->efuse_sw_en) |
| return 0; |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB2: |
| ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); |
| if (ret) { |
| dev_err(dev, "fail to get u2 intr efuse, %d\n", ret); |
| break; |
| } |
| |
| /* no efuse, ignore it */ |
| if (!instance->efuse_intr) { |
| dev_warn(dev, "no u2 intr efuse, but dts enable it\n"); |
| instance->efuse_sw_en = 0; |
| break; |
| } |
| |
| dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr); |
| break; |
| |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_PCIE: |
| ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); |
| if (ret) { |
| dev_err(dev, "fail to get u3 intr efuse, %d\n", ret); |
| break; |
| } |
| |
| ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp); |
| if (ret) { |
| dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret); |
| break; |
| } |
| |
| ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp); |
| if (ret) { |
| dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret); |
| break; |
| } |
| |
| /* no efuse, ignore it */ |
| if (!instance->efuse_intr && |
| !instance->efuse_rx_imp && |
| !instance->efuse_tx_imp) { |
| dev_warn(dev, "no u3 intr efuse, but dts enable it\n"); |
| instance->efuse_sw_en = 0; |
| break; |
| } |
| |
| dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n", |
| instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp); |
| break; |
| default: |
| dev_err(dev, "no sw efuse for type %d\n", instance->type); |
| ret = -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| static void phy_efuse_set(struct mtk_phy_instance *instance) |
| { |
| struct device *dev = &instance->phy->dev; |
| struct u2phy_banks *u2_banks = &instance->u2_banks; |
| struct u3phy_banks *u3_banks = &instance->u3_banks; |
| |
| if (!instance->efuse_sw_en) |
| return; |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB2: |
| mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1, MR1_EFUSE_AUTO_LOAD_DIS); |
| |
| mtk_phy_update_field(u2_banks->com + U3P_USBPHYACR1, PA1_RG_INTR_CAL, |
| instance->efuse_intr); |
| break; |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_PCIE: |
| mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_RSV, P3D_RG_EFUSE_AUTO_LOAD_DIS); |
| |
| mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL, |
| instance->efuse_tx_imp); |
| mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL); |
| |
| mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL, |
| instance->efuse_rx_imp); |
| mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL); |
| |
| mtk_phy_update_field(u3_banks->phya + U3P_U3_PHYA_REG0, P3A_RG_IEXT_INTR, |
| instance->efuse_intr); |
| break; |
| default: |
| dev_warn(dev, "no sw efuse for type %d\n", instance->type); |
| break; |
| } |
| } |
| |
| static int mtk_phy_init(struct phy *phy) |
| { |
| struct mtk_phy_instance *instance = phy_get_drvdata(phy); |
| struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent); |
| int ret; |
| |
| ret = clk_bulk_prepare_enable(TPHY_CLKS_CNT, instance->clks); |
| if (ret) |
| return ret; |
| |
| phy_efuse_set(instance); |
| |
| switch (instance->type) { |
| case PHY_TYPE_USB2: |
| u2_phy_instance_init(tphy, instance); |
| u2_phy_props_set(tphy, instance); |
| break; |
| case PHY_TYPE_USB3: |
| u3_phy_instance_init(tphy, instance); |
| break; |
| case PHY_TYPE_PCIE: |
| pcie_phy_instance_init(tphy, instance); |
| break; |
| case PHY_TYPE_SATA: |
| sata_phy_instance_init(tphy, instance); |
| break; |
| case PHY_TYPE_SGMII: |
| /* nothing to do, only used to set type */ |
| break; |
| default: |
| dev_err(tphy->dev, "incompatible PHY type\n"); |
| clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int mtk_phy_power_on(struct phy *phy) |
| { |
| struct mtk_phy_instance *instance = phy_get_drvdata(phy); |
| struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent); |
| |
| if (instance->type == PHY_TYPE_USB2) { |
| u2_phy_instance_power_on(tphy, instance); |
| hs_slew_rate_calibrate(tphy, instance); |
| } else if (instance->type == PHY_TYPE_PCIE) { |
| pcie_phy_instance_power_on(tphy, instance); |
| } |
| |
| return 0; |
| } |
| |
| static int mtk_phy_power_off(struct phy *phy) |
| { |
| struct mtk_phy_instance *instance = phy_get_drvdata(phy); |
| struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent); |
| |
| if (instance->type == PHY_TYPE_USB2) |
| u2_phy_instance_power_off(tphy, instance); |
| else if (instance->type == PHY_TYPE_PCIE) |
| pcie_phy_instance_power_off(tphy, instance); |
| |
| return 0; |
| } |
| |
| static int mtk_phy_exit(struct phy *phy) |
| { |
| struct mtk_phy_instance *instance = phy_get_drvdata(phy); |
| struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent); |
| |
| if (instance->type == PHY_TYPE_USB2) |
| u2_phy_instance_exit(tphy, instance); |
| |
| clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks); |
| return 0; |
| } |
| |
| static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode) |
| { |
| struct mtk_phy_instance *instance = phy_get_drvdata(phy); |
| struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent); |
| |
| if (instance->type == PHY_TYPE_USB2) |
| u2_phy_instance_set_mode(tphy, instance, mode); |
| |
| return 0; |
| } |
| |
| static struct phy *mtk_phy_xlate(struct device *dev, |
| const struct of_phandle_args *args) |
| { |
| struct mtk_tphy *tphy = dev_get_drvdata(dev); |
| struct mtk_phy_instance *instance = NULL; |
| struct device_node *phy_np = args->np; |
| int index; |
| int ret; |
| |
| if (args->args_count != 1) { |
| dev_err(dev, "invalid number of cells in 'phy' property\n"); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| for (index = 0; index < tphy->nphys; index++) |
| if (phy_np == tphy->phys[index]->phy->dev.of_node) { |
| instance = tphy->phys[index]; |
| break; |
| } |
| |
| if (!instance) { |
| dev_err(dev, "failed to find appropriate phy\n"); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| instance->type = args->args[0]; |
| if (!(instance->type == PHY_TYPE_USB2 || |
| instance->type == PHY_TYPE_USB3 || |
| instance->type == PHY_TYPE_PCIE || |
| instance->type == PHY_TYPE_SATA || |
| instance->type == PHY_TYPE_SGMII)) { |
| dev_err(dev, "unsupported device type: %d\n", instance->type); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| switch (tphy->pdata->version) { |
| case MTK_PHY_V1: |
| phy_v1_banks_init(tphy, instance); |
| break; |
| case MTK_PHY_V2: |
| case MTK_PHY_V3: |
| phy_v2_banks_init(tphy, instance); |
| break; |
| default: |
| dev_err(dev, "phy version is not supported\n"); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| ret = phy_efuse_get(tphy, instance); |
| if (ret) |
| return ERR_PTR(ret); |
| |
| phy_parse_property(tphy, instance); |
| phy_type_set(instance); |
| phy_debugfs_init(instance); |
| |
| return instance->phy; |
| } |
| |
| static const struct phy_ops mtk_tphy_ops = { |
| .init = mtk_phy_init, |
| .exit = mtk_phy_exit, |
| .power_on = mtk_phy_power_on, |
| .power_off = mtk_phy_power_off, |
| .set_mode = mtk_phy_set_mode, |
| .owner = THIS_MODULE, |
| }; |
| |
| static const struct mtk_phy_pdata tphy_v1_pdata = { |
| .avoid_rx_sen_degradation = false, |
| .version = MTK_PHY_V1, |
| }; |
| |
| static const struct mtk_phy_pdata tphy_v2_pdata = { |
| .avoid_rx_sen_degradation = false, |
| .sw_efuse_supported = true, |
| .version = MTK_PHY_V2, |
| }; |
| |
| static const struct mtk_phy_pdata tphy_v3_pdata = { |
| .sw_efuse_supported = true, |
| .version = MTK_PHY_V3, |
| }; |
| |
| static const struct mtk_phy_pdata mt8173_pdata = { |
| .avoid_rx_sen_degradation = true, |
| .version = MTK_PHY_V1, |
| }; |
| |
| static const struct mtk_phy_pdata mt8195_pdata = { |
| .sw_pll_48m_to_26m = true, |
| .sw_efuse_supported = true, |
| .version = MTK_PHY_V3, |
| }; |
| |
| static const struct of_device_id mtk_tphy_id_table[] = { |
| { .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata }, |
| { .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata }, |
| { .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata }, |
| { .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata }, |
| { .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata }, |
| { .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata }, |
| { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, mtk_tphy_id_table); |
| |
| static int mtk_tphy_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct device_node *np = dev->of_node; |
| struct phy_provider *provider; |
| struct resource *sif_res; |
| struct mtk_tphy *tphy; |
| struct resource res; |
| int port; |
| |
| tphy = devm_kzalloc(dev, sizeof(*tphy), GFP_KERNEL); |
| if (!tphy) |
| return -ENOMEM; |
| |
| tphy->pdata = of_device_get_match_data(dev); |
| if (!tphy->pdata) |
| return -EINVAL; |
| |
| tphy->nphys = of_get_child_count(np); |
| tphy->phys = devm_kcalloc(dev, tphy->nphys, |
| sizeof(*tphy->phys), GFP_KERNEL); |
| if (!tphy->phys) |
| return -ENOMEM; |
| |
| tphy->dev = dev; |
| platform_set_drvdata(pdev, tphy); |
| |
| sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| /* SATA phy of V1 needn't it if not shared with PCIe or USB */ |
| if (sif_res && tphy->pdata->version == MTK_PHY_V1) { |
| /* get banks shared by multiple phys */ |
| tphy->sif_base = devm_ioremap_resource(dev, sif_res); |
| if (IS_ERR(tphy->sif_base)) { |
| dev_err(dev, "failed to remap sif regs\n"); |
| return PTR_ERR(tphy->sif_base); |
| } |
| } |
| |
| if (tphy->pdata->version < MTK_PHY_V3) { |
| tphy->src_ref_clk = U3P_REF_CLK; |
| tphy->src_coef = U3P_SLEW_RATE_COEF; |
| /* update parameters of slew rate calibrate if exist */ |
| device_property_read_u32(dev, "mediatek,src-ref-clk-mhz", |
| &tphy->src_ref_clk); |
| device_property_read_u32(dev, "mediatek,src-coef", |
| &tphy->src_coef); |
| } |
| |
| port = 0; |
| for_each_child_of_node_scoped(np, child_np) { |
| struct mtk_phy_instance *instance; |
| struct clk_bulk_data *clks; |
| struct device *subdev; |
| struct phy *phy; |
| int retval; |
| |
| instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL); |
| if (!instance) |
| return -ENOMEM; |
| |
| tphy->phys[port] = instance; |
| |
| phy = devm_phy_create(dev, child_np, &mtk_tphy_ops); |
| if (IS_ERR(phy)) { |
| dev_err(dev, "failed to create phy\n"); |
| return PTR_ERR(phy); |
| } |
| |
| subdev = &phy->dev; |
| retval = of_address_to_resource(child_np, 0, &res); |
| if (retval) { |
| dev_err(subdev, "failed to get address resource(id-%d)\n", |
| port); |
| return retval; |
| } |
| |
| instance->port_base = devm_ioremap_resource(subdev, &res); |
| if (IS_ERR(instance->port_base)) |
| return PTR_ERR(instance->port_base); |
| |
| instance->phy = phy; |
| instance->index = port; |
| phy_set_drvdata(phy, instance); |
| port++; |
| |
| clks = instance->clks; |
| clks[0].id = "ref"; /* digital (& analog) clock */ |
| clks[1].id = "da_ref"; /* analog clock */ |
| retval = devm_clk_bulk_get_optional(subdev, TPHY_CLKS_CNT, clks); |
| if (retval) |
| return retval; |
| |
| retval = phy_type_syscon_get(instance, child_np); |
| if (retval) |
| return retval; |
| } |
| |
| provider = devm_of_phy_provider_register(dev, mtk_phy_xlate); |
| |
| return PTR_ERR_OR_ZERO(provider); |
| } |
| |
| static struct platform_driver mtk_tphy_driver = { |
| .probe = mtk_tphy_probe, |
| .driver = { |
| .name = "mtk-tphy", |
| .of_match_table = mtk_tphy_id_table, |
| }, |
| }; |
| |
| module_platform_driver(mtk_tphy_driver); |
| |
| MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>"); |
| MODULE_DESCRIPTION("MediaTek T-PHY driver"); |
| MODULE_LICENSE("GPL v2"); |