| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # 1-wire bus master configuration |
| # |
| |
| menu "1-wire Bus Masters" |
| |
| config W1_MASTER_AMD_AXI |
| tristate "AMD AXI 1-wire bus host" |
| help |
| Say Y here is you want to support the AMD AXI 1-wire IP core. |
| This driver makes use of the programmable logic IP to perform |
| correctly timed 1 wire transactions without relying on GPIO timing |
| through the kernel. |
| |
| This driver can also be built as a module. If so, the module will be |
| called amd_w1_axi. |
| |
| config W1_MASTER_MATROX |
| tristate "Matrox G400 transport layer for 1-wire" |
| depends on PCI |
| help |
| Say Y here if you want to communicate with your 1-wire devices |
| using Matrox's G400 GPIO pins. |
| |
| This support is also available as a module. If so, the module |
| will be called matrox_w1. |
| |
| config W1_MASTER_DS2490 |
| tristate "DS2490 USB <-> W1 transport layer for 1-wire" |
| depends on USB |
| help |
| Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges, |
| for example DS9490*. |
| |
| This support is also available as a module. If so, the module |
| will be called ds2490. |
| |
| config W1_MASTER_DS2482 |
| tristate "Maxim DS2482 I2C to 1-Wire bridge" |
| depends on I2C |
| help |
| If you say yes here you get support for the Maxim DS2482 |
| I2C to 1-Wire bridge. |
| |
| This driver can also be built as a module. If so, the module |
| will be called ds2482. |
| |
| config W1_MASTER_MXC |
| tristate "Freescale MXC 1-wire busmaster" |
| depends on ARCH_MXC || COMPILE_TEST |
| help |
| Say Y here to enable MXC 1-wire host |
| |
| config W1_MASTER_GPIO |
| tristate "GPIO 1-wire busmaster" |
| depends on GPIOLIB || COMPILE_TEST |
| help |
| Say Y here if you want to communicate with your 1-wire devices using |
| GPIO pins. This driver uses the GPIO API to control the wire. |
| |
| This support is also available as a module. If so, the module |
| will be called w1-gpio. |
| |
| config HDQ_MASTER_OMAP |
| tristate "OMAP HDQ driver" |
| depends on ARCH_OMAP || COMPILE_TEST |
| help |
| Say Y here if you want support for the 1-wire or HDQ Interface |
| on an OMAP processor. |
| |
| config W1_MASTER_SGI |
| tristate "SGI ASIC driver" |
| help |
| Say Y here if you want support for your 1-wire devices using |
| SGI ASIC 1-Wire interface |
| |
| This support is also available as a module. If so, the module |
| will be called sgi_w1. |
| |
| config W1_MASTER_UART |
| tristate "UART 1-wire driver" |
| depends on SERIAL_DEV_BUS |
| help |
| Say Y here if you want to communicate with your 1-wire devices using |
| UART interface. |
| |
| This support is also available as a module. If so, the module |
| will be called w1-uart. |
| |
| endmenu |
| |