| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # Pressure drivers |
| # |
| # When adding new entries keep the list in alphabetical order |
| |
| menu "Pressure sensors" |
| |
| config ABP060MG |
| tristate "Honeywell ABP pressure sensor driver" |
| depends on I2C |
| help |
| Say yes here to build support for the Honeywell ABP pressure |
| sensors. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called abp060mg. |
| |
| config BMP280 |
| tristate "Bosch Sensortec BMP180/BMP280 pressure sensor I2C driver" |
| depends on (I2C || SPI_MASTER) |
| select REGMAP |
| select BMP280_I2C if (I2C) |
| select BMP280_SPI if (SPI_MASTER) |
| help |
| Say yes here to build support for Bosch Sensortec BMP180 and BMP280 |
| pressure and temperature sensors. Also supports the BME280 with |
| an additional humidity sensor channel. |
| |
| To compile this driver as a module, choose M here: the core module |
| will be called bmp280 and you will also get bmp280-i2c for I2C |
| and/or bmp280-spi for SPI support. |
| |
| config BMP280_I2C |
| tristate |
| depends on BMP280 |
| depends on I2C |
| select REGMAP_I2C |
| |
| config BMP280_SPI |
| tristate |
| depends on BMP280 |
| depends on SPI_MASTER |
| select REGMAP |
| |
| config IIO_CROS_EC_BARO |
| tristate "ChromeOS EC Barometer Sensor" |
| depends on IIO_CROS_EC_SENSORS_CORE |
| help |
| Say yes here to build support for the Barometer sensor when |
| presented by the ChromeOS EC Sensor hub. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called cros_ec_baro. |
| |
| config DPS310 |
| tristate "Infineon DPS310 pressure and temperature sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Support for the Infineon DPS310 digital barometric pressure sensor. |
| It can be accessed over I2C bus. |
| |
| This driver can also be built as a module. If so, the module will be |
| called dps310. |
| |
| config HID_SENSOR_PRESS |
| depends on HID_SENSOR_HUB |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select HID_SENSOR_IIO_COMMON |
| select HID_SENSOR_IIO_TRIGGER |
| tristate "HID PRESS" |
| help |
| Say yes here to build support for the HID SENSOR |
| Pressure driver |
| |
| To compile this driver as a module, choose M here: the module |
| will be called hid-sensor-press. |
| |
| config HP03 |
| tristate "Hope RF HP03 temperature and pressure sensor driver" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say yes here to build support for Hope RF HP03 pressure and |
| temperature sensor. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called hp03. |
| |
| config MPL115 |
| tristate |
| |
| config MPL115_I2C |
| tristate "Freescale MPL115A2 pressure sensor driver" |
| depends on I2C |
| select MPL115 |
| help |
| Say yes here to build support for the Freescale MPL115A2 |
| pressure sensor connected via I2C. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called mpl115_i2c. |
| |
| config MPL115_SPI |
| tristate "Freescale MPL115A1 pressure sensor driver" |
| depends on SPI_MASTER |
| select MPL115 |
| help |
| Say yes here to build support for the Freescale MPL115A1 |
| pressure sensor connected via SPI. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called mpl115_spi. |
| |
| config MPL3115 |
| tristate "Freescale MPL3115A2 pressure sensor driver" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say yes here to build support for the Freescale MPL3115A2 |
| pressure sensor / altimeter. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called mpl3115. |
| |
| config MS5611 |
| tristate "Measurement Specialties MS5611 pressure sensor driver" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here to build support for the Measurement Specialties |
| MS5611, MS5607 pressure and temperature sensors. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called ms5611_core. |
| |
| config MS5611_I2C |
| tristate "support I2C bus connection" |
| depends on I2C && MS5611 |
| help |
| Say Y here to build I2C bus support for MS5611. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called ms5611_i2c. |
| |
| config MS5611_SPI |
| tristate "support SPI bus connection" |
| depends on SPI_MASTER && MS5611 |
| help |
| Say Y here to build SPI bus support for MS5611. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called ms5611_spi. |
| |
| config MS5637 |
| tristate "Measurement Specialties MS5637 pressure & temperature sensor" |
| depends on I2C |
| select IIO_MS_SENSORS_I2C |
| help |
| If you say yes here you get support for the Measurement Specialties |
| MS5637 pressure and temperature sensor. |
| This driver is also used for MS8607 temperature, pressure & humidity |
| sensor |
| |
| This driver can also be built as a module. If so, the module will |
| be called ms5637. |
| |
| config IIO_ST_PRESS |
| tristate "STMicroelectronics pressure sensor Driver" |
| depends on (I2C || SPI_MASTER) && SYSFS |
| select IIO_ST_SENSORS_CORE |
| select IIO_ST_PRESS_I2C if (I2C) |
| select IIO_ST_PRESS_SPI if (SPI_MASTER) |
| select IIO_TRIGGERED_BUFFER if (IIO_BUFFER) |
| help |
| Say yes here to build support for STMicroelectronics pressure |
| sensors: LPS001WP, LPS25H, LPS331AP, LPS22HB, LPS22HH. |
| |
| This driver can also be built as a module. If so, these modules |
| will be created: |
| - st_pressure (core functions for the driver [it is mandatory]); |
| - st_pressure_i2c (necessary for the I2C devices [optional*]); |
| - st_pressure_spi (necessary for the SPI devices [optional*]); |
| |
| (*) one of these is necessary to do something. |
| |
| config IIO_ST_PRESS_I2C |
| tristate |
| depends on IIO_ST_PRESS |
| depends on IIO_ST_SENSORS_I2C |
| |
| config IIO_ST_PRESS_SPI |
| tristate |
| depends on IIO_ST_PRESS |
| depends on IIO_ST_SENSORS_SPI |
| |
| config T5403 |
| tristate "EPCOS T5403 digital barometric pressure sensor driver" |
| depends on I2C |
| help |
| Say yes here to build support for the EPCOS T5403 pressure sensor |
| connected via I2C. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called t5403. |
| |
| config HP206C |
| tristate "HOPERF HP206C precision barometer and altimeter sensor" |
| depends on I2C |
| help |
| Say yes here to build support for the HOPREF HP206C precision |
| barometer and altimeter sensor. |
| |
| This driver can also be built as a module. If so, the module will |
| be called hp206c. |
| |
| config ZPA2326 |
| tristate "Murata ZPA2326 pressure sensor driver" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select REGMAP |
| select ZPA2326_I2C if I2C |
| select ZPA2326_SPI if SPI_MASTER |
| help |
| Say Y here to build support for the Murata ZPA2326 pressure and |
| temperature sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called zpa2326. |
| |
| config ZPA2326_I2C |
| tristate |
| select REGMAP_I2C |
| |
| config ZPA2326_SPI |
| tristate |
| select REGMAP_SPI |
| |
| endmenu |
