| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Cadence CDNSP DRD Driver. |
| * |
| * Copyright (C) 2020 Cadence. |
| * |
| * Author: Pawel Laszczak <pawell@cadence.com> |
| * |
| */ |
| |
| #include <linux/moduleparam.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/module.h> |
| #include <linux/iopoll.h> |
| #include <linux/delay.h> |
| #include <linux/log2.h> |
| #include <linux/slab.h> |
| #include <linux/pci.h> |
| #include <linux/irq.h> |
| #include <linux/dmi.h> |
| |
| #include "core.h" |
| #include "gadget-export.h" |
| #include "drd.h" |
| #include "cdnsp-gadget.h" |
| #include "cdnsp-trace.h" |
| |
| unsigned int cdnsp_port_speed(unsigned int port_status) |
| { |
| /*Detect gadget speed based on PORTSC register*/ |
| if (DEV_SUPERSPEEDPLUS(port_status)) |
| return USB_SPEED_SUPER_PLUS; |
| else if (DEV_SUPERSPEED(port_status)) |
| return USB_SPEED_SUPER; |
| else if (DEV_HIGHSPEED(port_status)) |
| return USB_SPEED_HIGH; |
| else if (DEV_FULLSPEED(port_status)) |
| return USB_SPEED_FULL; |
| |
| /* If device is detached then speed will be USB_SPEED_UNKNOWN.*/ |
| return USB_SPEED_UNKNOWN; |
| } |
| |
| /* |
| * Given a port state, this function returns a value that would result in the |
| * port being in the same state, if the value was written to the port status |
| * control register. |
| * Save Read Only (RO) bits and save read/write bits where |
| * writing a 0 clears the bit and writing a 1 sets the bit (RWS). |
| * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect. |
| */ |
| u32 cdnsp_port_state_to_neutral(u32 state) |
| { |
| /* Save read-only status and port state. */ |
| return (state & CDNSP_PORT_RO) | (state & CDNSP_PORT_RWS); |
| } |
| |
| /** |
| * cdnsp_find_next_ext_cap - Find the offset of the extended capabilities |
| * with capability ID id. |
| * @base: PCI MMIO registers base address. |
| * @start: Address at which to start looking, (0 or HCC_PARAMS to start at |
| * beginning of list) |
| * @id: Extended capability ID to search for. |
| * |
| * Returns the offset of the next matching extended capability structure. |
| * Some capabilities can occur several times, |
| * e.g., the EXT_CAPS_PROTOCOL, and this provides a way to find them all. |
| */ |
| int cdnsp_find_next_ext_cap(void __iomem *base, u32 start, int id) |
| { |
| u32 offset = start; |
| u32 next; |
| u32 val; |
| |
| if (!start || start == HCC_PARAMS_OFFSET) { |
| val = readl(base + HCC_PARAMS_OFFSET); |
| if (val == ~0) |
| return 0; |
| |
| offset = HCC_EXT_CAPS(val) << 2; |
| if (!offset) |
| return 0; |
| } |
| |
| do { |
| val = readl(base + offset); |
| if (val == ~0) |
| return 0; |
| |
| if (EXT_CAPS_ID(val) == id && offset != start) |
| return offset; |
| |
| next = EXT_CAPS_NEXT(val); |
| offset += next << 2; |
| } while (next); |
| |
| return 0; |
| } |
| |
| void cdnsp_set_link_state(struct cdnsp_device *pdev, |
| __le32 __iomem *port_regs, |
| u32 link_state) |
| { |
| int port_num = 0xFF; |
| u32 temp; |
| |
| temp = readl(port_regs); |
| temp = cdnsp_port_state_to_neutral(temp); |
| temp |= PORT_WKCONN_E | PORT_WKDISC_E; |
| writel(temp, port_regs); |
| |
| temp &= ~PORT_PLS_MASK; |
| temp |= PORT_LINK_STROBE | link_state; |
| |
| if (pdev->active_port) |
| port_num = pdev->active_port->port_num; |
| |
| trace_cdnsp_handle_port_status(port_num, readl(port_regs)); |
| writel(temp, port_regs); |
| trace_cdnsp_link_state_changed(port_num, readl(port_regs)); |
| } |
| |
| static void cdnsp_disable_port(struct cdnsp_device *pdev, |
| __le32 __iomem *port_regs) |
| { |
| u32 temp = cdnsp_port_state_to_neutral(readl(port_regs)); |
| |
| writel(temp | PORT_PED, port_regs); |
| } |
| |
| static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev, |
| __le32 __iomem *port_regs) |
| { |
| u32 portsc = readl(port_regs); |
| |
| writel(cdnsp_port_state_to_neutral(portsc) | |
| (portsc & PORT_CHANGE_BITS), port_regs); |
| } |
| |
| static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit) |
| { |
| __le32 __iomem *reg; |
| void __iomem *base; |
| u32 offset = 0; |
| |
| base = &pdev->cap_regs->hc_capbase; |
| offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP); |
| reg = base + offset + REG_CHICKEN_BITS_2_OFFSET; |
| |
| bit = readl(reg) | bit; |
| writel(bit, reg); |
| } |
| |
| static void cdnsp_clear_chicken_bits_2(struct cdnsp_device *pdev, u32 bit) |
| { |
| __le32 __iomem *reg; |
| void __iomem *base; |
| u32 offset = 0; |
| |
| base = &pdev->cap_regs->hc_capbase; |
| offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP); |
| reg = base + offset + REG_CHICKEN_BITS_2_OFFSET; |
| |
| bit = readl(reg) & ~bit; |
| writel(bit, reg); |
| } |
| |
| /* |
| * Disable interrupts and begin the controller halting process. |
| */ |
| static void cdnsp_quiesce(struct cdnsp_device *pdev) |
| { |
| u32 halted; |
| u32 mask; |
| u32 cmd; |
| |
| mask = ~(u32)(CDNSP_IRQS); |
| |
| halted = readl(&pdev->op_regs->status) & STS_HALT; |
| if (!halted) |
| mask &= ~(CMD_R_S | CMD_DEVEN); |
| |
| cmd = readl(&pdev->op_regs->command); |
| cmd &= mask; |
| writel(cmd, &pdev->op_regs->command); |
| } |
| |
| /* |
| * Force controller into halt state. |
| * |
| * Disable any IRQs and clear the run/stop bit. |
| * Controller will complete any current and actively pipelined transactions, and |
| * should halt within 16 ms of the run/stop bit being cleared. |
| * Read controller Halted bit in the status register to see when the |
| * controller is finished. |
| */ |
| int cdnsp_halt(struct cdnsp_device *pdev) |
| { |
| int ret; |
| u32 val; |
| |
| cdnsp_quiesce(pdev); |
| |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, val, |
| val & STS_HALT, 1, |
| CDNSP_MAX_HALT_USEC); |
| if (ret) { |
| dev_err(pdev->dev, "ERROR: Device halt failed\n"); |
| return ret; |
| } |
| |
| pdev->cdnsp_state |= CDNSP_STATE_HALTED; |
| |
| return 0; |
| } |
| |
| /* |
| * device controller died, register read returns 0xffffffff, or command never |
| * ends. |
| */ |
| void cdnsp_died(struct cdnsp_device *pdev) |
| { |
| dev_err(pdev->dev, "ERROR: CDNSP controller not responding\n"); |
| pdev->cdnsp_state |= CDNSP_STATE_DYING; |
| cdnsp_halt(pdev); |
| } |
| |
| /* |
| * Set the run bit and wait for the device to be running. |
| */ |
| static int cdnsp_start(struct cdnsp_device *pdev) |
| { |
| u32 temp; |
| int ret; |
| |
| temp = readl(&pdev->op_regs->command); |
| temp |= (CMD_R_S | CMD_DEVEN); |
| writel(temp, &pdev->op_regs->command); |
| |
| pdev->cdnsp_state = 0; |
| |
| /* |
| * Wait for the STS_HALT Status bit to be 0 to indicate the device is |
| * running. |
| */ |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp, |
| !(temp & STS_HALT), 1, |
| CDNSP_MAX_HALT_USEC); |
| if (ret) { |
| pdev->cdnsp_state = CDNSP_STATE_DYING; |
| dev_err(pdev->dev, "ERROR: Controller run failed\n"); |
| } |
| |
| return ret; |
| } |
| |
| /* |
| * Reset a halted controller. |
| * |
| * This resets pipelines, timers, counters, state machines, etc. |
| * Transactions will be terminated immediately, and operational registers |
| * will be set to their defaults. |
| */ |
| int cdnsp_reset(struct cdnsp_device *pdev) |
| { |
| u32 command; |
| u32 temp; |
| int ret; |
| |
| temp = readl(&pdev->op_regs->status); |
| |
| if (temp == ~(u32)0) { |
| dev_err(pdev->dev, "Device not accessible, reset failed.\n"); |
| return -ENODEV; |
| } |
| |
| if ((temp & STS_HALT) == 0) { |
| dev_err(pdev->dev, "Controller not halted, aborting reset.\n"); |
| return -EINVAL; |
| } |
| |
| command = readl(&pdev->op_regs->command); |
| command |= CMD_RESET; |
| writel(command, &pdev->op_regs->command); |
| |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->command, temp, |
| !(temp & CMD_RESET), 1, |
| 10 * 1000); |
| if (ret) { |
| dev_err(pdev->dev, "ERROR: Controller reset failed\n"); |
| return ret; |
| } |
| |
| /* |
| * CDNSP cannot write any doorbells or operational registers other |
| * than status until the "Controller Not Ready" flag is cleared. |
| */ |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->status, temp, |
| !(temp & STS_CNR), 1, |
| 10 * 1000); |
| |
| if (ret) { |
| dev_err(pdev->dev, "ERROR: Controller not ready to work\n"); |
| return ret; |
| } |
| |
| dev_dbg(pdev->dev, "Controller ready to work"); |
| |
| return ret; |
| } |
| |
| /* |
| * cdnsp_get_endpoint_index - Find the index for an endpoint given its |
| * descriptor.Use the return value to right shift 1 for the bitmask. |
| * |
| * Index = (epnum * 2) + direction - 1, |
| * where direction = 0 for OUT, 1 for IN. |
| * For control endpoints, the IN index is used (OUT index is unused), so |
| * index = (epnum * 2) + direction - 1 = (epnum * 2) + 1 - 1 = (epnum * 2) |
| */ |
| static unsigned int |
| cdnsp_get_endpoint_index(const struct usb_endpoint_descriptor *desc) |
| { |
| unsigned int index = (unsigned int)usb_endpoint_num(desc); |
| |
| if (usb_endpoint_xfer_control(desc)) |
| return index * 2; |
| |
| return (index * 2) + (usb_endpoint_dir_in(desc) ? 1 : 0) - 1; |
| } |
| |
| /* |
| * Find the flag for this endpoint (for use in the control context). Use the |
| * endpoint index to create a bitmask. The slot context is bit 0, endpoint 0 is |
| * bit 1, etc. |
| */ |
| static unsigned int |
| cdnsp_get_endpoint_flag(const struct usb_endpoint_descriptor *desc) |
| { |
| return 1 << (cdnsp_get_endpoint_index(desc) + 1); |
| } |
| |
| int cdnsp_ep_enqueue(struct cdnsp_ep *pep, struct cdnsp_request *preq) |
| { |
| struct cdnsp_device *pdev = pep->pdev; |
| struct usb_request *request; |
| int ret; |
| |
| if (preq->epnum == 0 && !list_empty(&pep->pending_list)) { |
| trace_cdnsp_request_enqueue_busy(preq); |
| return -EBUSY; |
| } |
| |
| request = &preq->request; |
| request->actual = 0; |
| request->status = -EINPROGRESS; |
| preq->direction = pep->direction; |
| preq->epnum = pep->number; |
| preq->td.drbl = 0; |
| |
| ret = usb_gadget_map_request_by_dev(pdev->dev, request, pep->direction); |
| if (ret) { |
| trace_cdnsp_request_enqueue_error(preq); |
| return ret; |
| } |
| |
| list_add_tail(&preq->list, &pep->pending_list); |
| |
| trace_cdnsp_request_enqueue(preq); |
| |
| switch (usb_endpoint_type(pep->endpoint.desc)) { |
| case USB_ENDPOINT_XFER_CONTROL: |
| ret = cdnsp_queue_ctrl_tx(pdev, preq); |
| break; |
| case USB_ENDPOINT_XFER_BULK: |
| case USB_ENDPOINT_XFER_INT: |
| ret = cdnsp_queue_bulk_tx(pdev, preq); |
| break; |
| case USB_ENDPOINT_XFER_ISOC: |
| ret = cdnsp_queue_isoc_tx_prepare(pdev, preq); |
| } |
| |
| if (ret) |
| goto unmap; |
| |
| return 0; |
| |
| unmap: |
| usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request, |
| pep->direction); |
| list_del(&preq->list); |
| trace_cdnsp_request_enqueue_error(preq); |
| |
| return ret; |
| } |
| |
| /* |
| * Remove the request's TD from the endpoint ring. This may cause the |
| * controller to stop USB transfers, potentially stopping in the middle of a |
| * TRB buffer. The controller should pick up where it left off in the TD, |
| * unless a Set Transfer Ring Dequeue Pointer is issued. |
| * |
| * The TRBs that make up the buffers for the canceled request will be "removed" |
| * from the ring. Since the ring is a contiguous structure, they can't be |
| * physically removed. Instead, there are two options: |
| * |
| * 1) If the controller is in the middle of processing the request to be |
| * canceled, we simply move the ring's dequeue pointer past those TRBs |
| * using the Set Transfer Ring Dequeue Pointer command. This will be |
| * the common case, when drivers timeout on the last submitted request |
| * and attempt to cancel. |
| * |
| * 2) If the controller is in the middle of a different TD, we turn the TRBs |
| * into a series of 1-TRB transfer no-op TDs. No-ops shouldn't be chained. |
| * The controller will need to invalidate the any TRBs it has cached after |
| * the stop endpoint command. |
| * |
| * 3) The TD may have completed by the time the Stop Endpoint Command |
| * completes, so software needs to handle that case too. |
| * |
| */ |
| int cdnsp_ep_dequeue(struct cdnsp_ep *pep, struct cdnsp_request *preq) |
| { |
| struct cdnsp_device *pdev = pep->pdev; |
| int ret_stop = 0; |
| int ret_rem; |
| |
| trace_cdnsp_request_dequeue(preq); |
| |
| if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_RUNNING) |
| ret_stop = cdnsp_cmd_stop_ep(pdev, pep); |
| |
| ret_rem = cdnsp_remove_request(pdev, preq, pep); |
| |
| return ret_rem ? ret_rem : ret_stop; |
| } |
| |
| static void cdnsp_zero_in_ctx(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_input_control_ctx *ctrl_ctx; |
| struct cdnsp_slot_ctx *slot_ctx; |
| struct cdnsp_ep_ctx *ep_ctx; |
| int i; |
| |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); |
| |
| /* |
| * When a device's add flag and drop flag are zero, any subsequent |
| * configure endpoint command will leave that endpoint's state |
| * untouched. Make sure we don't leave any old state in the input |
| * endpoint contexts. |
| */ |
| ctrl_ctx->drop_flags = 0; |
| ctrl_ctx->add_flags = 0; |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); |
| slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK); |
| |
| /* Endpoint 0 is always valid */ |
| slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(1)); |
| for (i = 1; i < CDNSP_ENDPOINTS_NUM; ++i) { |
| ep_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, i); |
| ep_ctx->ep_info = 0; |
| ep_ctx->ep_info2 = 0; |
| ep_ctx->deq = 0; |
| ep_ctx->tx_info = 0; |
| } |
| } |
| |
| /* Issue a configure endpoint command and wait for it to finish. */ |
| static int cdnsp_configure_endpoint(struct cdnsp_device *pdev) |
| { |
| int ret; |
| |
| cdnsp_queue_configure_endpoint(pdev, pdev->cmd.in_ctx->dma); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| if (ret) { |
| dev_err(pdev->dev, |
| "ERR: unexpected command completion code 0x%x.\n", ret); |
| return -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| static void cdnsp_invalidate_ep_events(struct cdnsp_device *pdev, |
| struct cdnsp_ep *pep) |
| { |
| struct cdnsp_segment *segment; |
| union cdnsp_trb *event; |
| u32 cycle_state; |
| u32 data; |
| |
| event = pdev->event_ring->dequeue; |
| segment = pdev->event_ring->deq_seg; |
| cycle_state = pdev->event_ring->cycle_state; |
| |
| while (1) { |
| data = le32_to_cpu(event->trans_event.flags); |
| |
| /* Check the owner of the TRB. */ |
| if ((data & TRB_CYCLE) != cycle_state) |
| break; |
| |
| if (TRB_FIELD_TO_TYPE(data) == TRB_TRANSFER && |
| TRB_TO_EP_ID(data) == (pep->idx + 1)) { |
| data |= TRB_EVENT_INVALIDATE; |
| event->trans_event.flags = cpu_to_le32(data); |
| } |
| |
| if (cdnsp_last_trb_on_seg(segment, event)) { |
| cycle_state ^= 1; |
| segment = pdev->event_ring->deq_seg->next; |
| event = segment->trbs; |
| } else { |
| event++; |
| } |
| } |
| } |
| |
| int cdnsp_wait_for_cmd_compl(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_segment *event_deq_seg; |
| union cdnsp_trb *cmd_trb; |
| dma_addr_t cmd_deq_dma; |
| union cdnsp_trb *event; |
| u32 cycle_state; |
| int ret, val; |
| u64 cmd_dma; |
| u32 flags; |
| |
| cmd_trb = pdev->cmd.command_trb; |
| pdev->cmd.status = 0; |
| |
| trace_cdnsp_cmd_wait_for_compl(pdev->cmd_ring, &cmd_trb->generic); |
| |
| ret = readl_poll_timeout_atomic(&pdev->op_regs->cmd_ring, val, |
| !CMD_RING_BUSY(val), 1, |
| CDNSP_CMD_TIMEOUT); |
| if (ret) { |
| dev_err(pdev->dev, "ERR: Timeout while waiting for command\n"); |
| trace_cdnsp_cmd_timeout(pdev->cmd_ring, &cmd_trb->generic); |
| pdev->cdnsp_state = CDNSP_STATE_DYING; |
| return -ETIMEDOUT; |
| } |
| |
| event = pdev->event_ring->dequeue; |
| event_deq_seg = pdev->event_ring->deq_seg; |
| cycle_state = pdev->event_ring->cycle_state; |
| |
| cmd_deq_dma = cdnsp_trb_virt_to_dma(pdev->cmd_ring->deq_seg, cmd_trb); |
| if (!cmd_deq_dma) |
| return -EINVAL; |
| |
| while (1) { |
| flags = le32_to_cpu(event->event_cmd.flags); |
| |
| /* Check the owner of the TRB. */ |
| if ((flags & TRB_CYCLE) != cycle_state) |
| return -EINVAL; |
| |
| cmd_dma = le64_to_cpu(event->event_cmd.cmd_trb); |
| |
| /* |
| * Check whether the completion event is for last queued |
| * command. |
| */ |
| if (TRB_FIELD_TO_TYPE(flags) != TRB_COMPLETION || |
| cmd_dma != (u64)cmd_deq_dma) { |
| if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) { |
| event++; |
| continue; |
| } |
| |
| if (cdnsp_last_trb_on_ring(pdev->event_ring, |
| event_deq_seg, event)) |
| cycle_state ^= 1; |
| |
| event_deq_seg = event_deq_seg->next; |
| event = event_deq_seg->trbs; |
| continue; |
| } |
| |
| trace_cdnsp_handle_command(pdev->cmd_ring, &cmd_trb->generic); |
| |
| pdev->cmd.status = GET_COMP_CODE(le32_to_cpu(event->event_cmd.status)); |
| if (pdev->cmd.status == COMP_SUCCESS) |
| return 0; |
| |
| return -pdev->cmd.status; |
| } |
| } |
| |
| int cdnsp_halt_endpoint(struct cdnsp_device *pdev, |
| struct cdnsp_ep *pep, |
| int value) |
| { |
| int ret; |
| |
| trace_cdnsp_ep_halt(value ? "Set" : "Clear"); |
| |
| if (value) { |
| ret = cdnsp_cmd_stop_ep(pdev, pep); |
| if (ret) |
| return ret; |
| |
| if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_STOPPED) { |
| cdnsp_queue_halt_endpoint(pdev, pep->idx); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| } |
| |
| pep->ep_state |= EP_HALTED; |
| } else { |
| /* |
| * In device mode driver can call reset endpoint command |
| * from any endpoint state. |
| */ |
| cdnsp_queue_reset_ep(pdev, pep->idx); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| trace_cdnsp_handle_cmd_reset_ep(pep->out_ctx); |
| |
| if (ret) |
| return ret; |
| |
| pep->ep_state &= ~EP_HALTED; |
| |
| if (pep->idx != 0 && !(pep->ep_state & EP_WEDGE)) |
| cdnsp_ring_doorbell_for_active_rings(pdev, pep); |
| |
| pep->ep_state &= ~EP_WEDGE; |
| } |
| |
| return 0; |
| } |
| |
| static int cdnsp_update_eps_configuration(struct cdnsp_device *pdev, |
| struct cdnsp_ep *pep) |
| { |
| struct cdnsp_input_control_ctx *ctrl_ctx; |
| struct cdnsp_slot_ctx *slot_ctx; |
| int ret = 0; |
| u32 ep_sts; |
| int i; |
| |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); |
| |
| /* Don't issue the command if there's no endpoints to update. */ |
| if (ctrl_ctx->add_flags == 0 && ctrl_ctx->drop_flags == 0) |
| return 0; |
| |
| ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG); |
| ctrl_ctx->add_flags &= cpu_to_le32(~EP0_FLAG); |
| ctrl_ctx->drop_flags &= cpu_to_le32(~(SLOT_FLAG | EP0_FLAG)); |
| |
| /* Fix up Context Entries field. Minimum value is EP0 == BIT(1). */ |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); |
| for (i = CDNSP_ENDPOINTS_NUM; i >= 1; i--) { |
| __le32 le32 = cpu_to_le32(BIT(i)); |
| |
| if ((pdev->eps[i - 1].ring && !(ctrl_ctx->drop_flags & le32)) || |
| (ctrl_ctx->add_flags & le32) || i == 1) { |
| slot_ctx->dev_info &= cpu_to_le32(~LAST_CTX_MASK); |
| slot_ctx->dev_info |= cpu_to_le32(LAST_CTX(i)); |
| break; |
| } |
| } |
| |
| ep_sts = GET_EP_CTX_STATE(pep->out_ctx); |
| |
| if ((ctrl_ctx->add_flags != cpu_to_le32(SLOT_FLAG) && |
| ep_sts == EP_STATE_DISABLED) || |
| (ep_sts != EP_STATE_DISABLED && ctrl_ctx->drop_flags)) |
| ret = cdnsp_configure_endpoint(pdev); |
| |
| trace_cdnsp_configure_endpoint(cdnsp_get_slot_ctx(&pdev->out_ctx)); |
| trace_cdnsp_handle_cmd_config_ep(pep->out_ctx); |
| |
| cdnsp_zero_in_ctx(pdev); |
| |
| return ret; |
| } |
| |
| /* |
| * This submits a Reset Device Command, which will set the device state to 0, |
| * set the device address to 0, and disable all the endpoints except the default |
| * control endpoint. The USB core should come back and call |
| * cdnsp_setup_device(), and then re-set up the configuration. |
| */ |
| int cdnsp_reset_device(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_slot_ctx *slot_ctx; |
| int slot_state; |
| int ret, i; |
| |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); |
| slot_ctx->dev_info = 0; |
| pdev->device_address = 0; |
| |
| /* If device is not setup, there is no point in resetting it. */ |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); |
| slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); |
| trace_cdnsp_reset_device(slot_ctx); |
| |
| if (slot_state <= SLOT_STATE_DEFAULT && |
| pdev->eps[0].ep_state & EP_HALTED) { |
| cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0); |
| } |
| |
| /* |
| * During Reset Device command controller shall transition the |
| * endpoint ep0 to the Running State. |
| */ |
| pdev->eps[0].ep_state &= ~(EP_STOPPED | EP_HALTED); |
| pdev->eps[0].ep_state |= EP_ENABLED; |
| |
| if (slot_state <= SLOT_STATE_DEFAULT) |
| return 0; |
| |
| cdnsp_queue_reset_device(pdev); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| |
| /* |
| * After Reset Device command all not default endpoints |
| * are in Disabled state. |
| */ |
| for (i = 1; i < CDNSP_ENDPOINTS_NUM; ++i) |
| pdev->eps[i].ep_state |= EP_STOPPED | EP_UNCONFIGURED; |
| |
| trace_cdnsp_handle_cmd_reset_dev(slot_ctx); |
| |
| if (ret) |
| dev_err(pdev->dev, "Reset device failed with error code %d", |
| ret); |
| |
| return ret; |
| } |
| |
| /* |
| * Sets the MaxPStreams field and the Linear Stream Array field. |
| * Sets the dequeue pointer to the stream context array. |
| */ |
| static void cdnsp_setup_streams_ep_input_ctx(struct cdnsp_device *pdev, |
| struct cdnsp_ep_ctx *ep_ctx, |
| struct cdnsp_stream_info *stream_info) |
| { |
| u32 max_primary_streams; |
| |
| /* MaxPStreams is the number of stream context array entries, not the |
| * number we're actually using. Must be in 2^(MaxPstreams + 1) format. |
| * fls(0) = 0, fls(0x1) = 1, fls(0x10) = 2, fls(0x100) = 3, etc. |
| */ |
| max_primary_streams = fls(stream_info->num_stream_ctxs) - 2; |
| ep_ctx->ep_info &= cpu_to_le32(~EP_MAXPSTREAMS_MASK); |
| ep_ctx->ep_info |= cpu_to_le32(EP_MAXPSTREAMS(max_primary_streams) |
| | EP_HAS_LSA); |
| ep_ctx->deq = cpu_to_le64(stream_info->ctx_array_dma); |
| } |
| |
| /* |
| * The drivers use this function to prepare a bulk endpoints to use streams. |
| * |
| * Don't allow the call to succeed if endpoint only supports one stream |
| * (which means it doesn't support streams at all). |
| */ |
| int cdnsp_alloc_streams(struct cdnsp_device *pdev, struct cdnsp_ep *pep) |
| { |
| unsigned int num_streams = usb_ss_max_streams(pep->endpoint.comp_desc); |
| unsigned int num_stream_ctxs; |
| int ret; |
| |
| if (num_streams == 0) |
| return 0; |
| |
| if (num_streams > STREAM_NUM_STREAMS) |
| return -EINVAL; |
| |
| /* |
| * Add two to the number of streams requested to account for |
| * stream 0 that is reserved for controller usage and one additional |
| * for TASK SET FULL response. |
| */ |
| num_streams += 2; |
| |
| /* The stream context array size must be a power of two */ |
| num_stream_ctxs = roundup_pow_of_two(num_streams); |
| |
| trace_cdnsp_stream_number(pep, num_stream_ctxs, num_streams); |
| |
| ret = cdnsp_alloc_stream_info(pdev, pep, num_stream_ctxs, num_streams); |
| if (ret) |
| return ret; |
| |
| cdnsp_setup_streams_ep_input_ctx(pdev, pep->in_ctx, &pep->stream_info); |
| |
| pep->ep_state |= EP_HAS_STREAMS; |
| pep->stream_info.td_count = 0; |
| pep->stream_info.first_prime_det = 0; |
| |
| /* Subtract 1 for stream 0, which drivers can't use. */ |
| return num_streams - 1; |
| } |
| |
| int cdnsp_disable_slot(struct cdnsp_device *pdev) |
| { |
| int ret; |
| |
| cdnsp_queue_slot_control(pdev, TRB_DISABLE_SLOT); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| |
| pdev->slot_id = 0; |
| pdev->active_port = NULL; |
| |
| trace_cdnsp_handle_cmd_disable_slot(cdnsp_get_slot_ctx(&pdev->out_ctx)); |
| |
| memset(pdev->in_ctx.bytes, 0, CDNSP_CTX_SIZE); |
| memset(pdev->out_ctx.bytes, 0, CDNSP_CTX_SIZE); |
| |
| return ret; |
| } |
| |
| int cdnsp_enable_slot(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_slot_ctx *slot_ctx; |
| int slot_state; |
| int ret; |
| |
| /* If device is not setup, there is no point in resetting it */ |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); |
| slot_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); |
| |
| if (slot_state != SLOT_STATE_DISABLED) |
| return 0; |
| |
| cdnsp_queue_slot_control(pdev, TRB_ENABLE_SLOT); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| if (ret) |
| goto show_trace; |
| |
| pdev->slot_id = 1; |
| |
| show_trace: |
| trace_cdnsp_handle_cmd_enable_slot(cdnsp_get_slot_ctx(&pdev->out_ctx)); |
| |
| return ret; |
| } |
| |
| /* |
| * Issue an Address Device command with BSR=0 if setup is SETUP_CONTEXT_ONLY |
| * or with BSR = 1 if set_address is SETUP_CONTEXT_ADDRESS. |
| */ |
| int cdnsp_setup_device(struct cdnsp_device *pdev, enum cdnsp_setup_dev setup) |
| { |
| struct cdnsp_input_control_ctx *ctrl_ctx; |
| struct cdnsp_slot_ctx *slot_ctx; |
| int dev_state = 0; |
| int ret; |
| |
| if (!pdev->slot_id) { |
| trace_cdnsp_slot_id("incorrect"); |
| return -EINVAL; |
| } |
| |
| if (!pdev->active_port->port_num) |
| return -EINVAL; |
| |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->out_ctx); |
| dev_state = GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)); |
| |
| if (setup == SETUP_CONTEXT_ONLY && dev_state == SLOT_STATE_DEFAULT) { |
| trace_cdnsp_slot_already_in_default(slot_ctx); |
| return 0; |
| } |
| |
| slot_ctx = cdnsp_get_slot_ctx(&pdev->in_ctx); |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); |
| |
| if (!slot_ctx->dev_info || dev_state == SLOT_STATE_DEFAULT) { |
| ret = cdnsp_setup_addressable_priv_dev(pdev); |
| if (ret) |
| return ret; |
| } |
| |
| cdnsp_copy_ep0_dequeue_into_input_ctx(pdev); |
| |
| ctrl_ctx->add_flags = cpu_to_le32(SLOT_FLAG | EP0_FLAG); |
| ctrl_ctx->drop_flags = 0; |
| |
| trace_cdnsp_setup_device_slot(slot_ctx); |
| |
| cdnsp_queue_address_device(pdev, pdev->in_ctx.dma, setup); |
| cdnsp_ring_cmd_db(pdev); |
| ret = cdnsp_wait_for_cmd_compl(pdev); |
| |
| trace_cdnsp_handle_cmd_addr_dev(cdnsp_get_slot_ctx(&pdev->out_ctx)); |
| |
| /* Zero the input context control for later use. */ |
| ctrl_ctx->add_flags = 0; |
| ctrl_ctx->drop_flags = 0; |
| |
| return ret; |
| } |
| |
| void cdnsp_set_usb2_hardware_lpm(struct cdnsp_device *pdev, |
| struct usb_request *req, |
| int enable) |
| { |
| if (pdev->active_port != &pdev->usb2_port || !pdev->gadget.lpm_capable) |
| return; |
| |
| trace_cdnsp_lpm(enable); |
| |
| if (enable) |
| writel(PORT_BESL(CDNSP_DEFAULT_BESL) | PORT_L1S_NYET | PORT_HLE, |
| &pdev->active_port->regs->portpmsc); |
| else |
| writel(PORT_L1S_NYET, &pdev->active_port->regs->portpmsc); |
| } |
| |
| static int cdnsp_get_frame(struct cdnsp_device *pdev) |
| { |
| return readl(&pdev->run_regs->microframe_index) >> 3; |
| } |
| |
| static int cdnsp_gadget_ep_enable(struct usb_ep *ep, |
| const struct usb_endpoint_descriptor *desc) |
| { |
| struct cdnsp_input_control_ctx *ctrl_ctx; |
| struct cdnsp_device *pdev; |
| struct cdnsp_ep *pep; |
| unsigned long flags; |
| u32 added_ctxs; |
| int ret; |
| |
| if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT || |
| !desc->wMaxPacketSize) |
| return -EINVAL; |
| |
| pep = to_cdnsp_ep(ep); |
| pdev = pep->pdev; |
| pep->ep_state &= ~EP_UNCONFIGURED; |
| |
| if (dev_WARN_ONCE(pdev->dev, pep->ep_state & EP_ENABLED, |
| "%s is already enabled\n", pep->name)) |
| return 0; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| |
| added_ctxs = cdnsp_get_endpoint_flag(desc); |
| if (added_ctxs == SLOT_FLAG || added_ctxs == EP0_FLAG) { |
| dev_err(pdev->dev, "ERROR: Bad endpoint number\n"); |
| ret = -EINVAL; |
| goto unlock; |
| } |
| |
| pep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0; |
| |
| if (pdev->gadget.speed == USB_SPEED_FULL) { |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_INT) |
| pep->interval = desc->bInterval << 3; |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) |
| pep->interval = BIT(desc->bInterval - 1) << 3; |
| } |
| |
| if (usb_endpoint_type(desc) == USB_ENDPOINT_XFER_ISOC) { |
| if (pep->interval > BIT(12)) { |
| dev_err(pdev->dev, "bInterval %d not supported\n", |
| desc->bInterval); |
| ret = -EINVAL; |
| goto unlock; |
| } |
| cdnsp_set_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS); |
| } |
| |
| ret = cdnsp_endpoint_init(pdev, pep, GFP_ATOMIC); |
| if (ret) |
| goto unlock; |
| |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); |
| ctrl_ctx->add_flags = cpu_to_le32(added_ctxs); |
| ctrl_ctx->drop_flags = 0; |
| |
| ret = cdnsp_update_eps_configuration(pdev, pep); |
| if (ret) { |
| cdnsp_free_endpoint_rings(pdev, pep); |
| goto unlock; |
| } |
| |
| pep->ep_state |= EP_ENABLED; |
| pep->ep_state &= ~EP_STOPPED; |
| |
| unlock: |
| trace_cdnsp_ep_enable_end(pep, 0); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| static int cdnsp_gadget_ep_disable(struct usb_ep *ep) |
| { |
| struct cdnsp_input_control_ctx *ctrl_ctx; |
| struct cdnsp_request *preq; |
| struct cdnsp_device *pdev; |
| struct cdnsp_ep *pep; |
| unsigned long flags; |
| u32 drop_flag; |
| int ret = 0; |
| |
| if (!ep) |
| return -EINVAL; |
| |
| pep = to_cdnsp_ep(ep); |
| pdev = pep->pdev; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| |
| if (!(pep->ep_state & EP_ENABLED)) { |
| dev_err(pdev->dev, "%s is already disabled\n", pep->name); |
| ret = -EINVAL; |
| goto finish; |
| } |
| |
| pep->ep_state |= EP_DIS_IN_RROGRESS; |
| |
| /* Endpoint was unconfigured by Reset Device command. */ |
| if (!(pep->ep_state & EP_UNCONFIGURED)) { |
| cdnsp_cmd_stop_ep(pdev, pep); |
| cdnsp_cmd_flush_ep(pdev, pep); |
| } |
| |
| /* Remove all queued USB requests. */ |
| while (!list_empty(&pep->pending_list)) { |
| preq = next_request(&pep->pending_list); |
| cdnsp_ep_dequeue(pep, preq); |
| } |
| |
| cdnsp_invalidate_ep_events(pdev, pep); |
| |
| pep->ep_state &= ~EP_DIS_IN_RROGRESS; |
| drop_flag = cdnsp_get_endpoint_flag(pep->endpoint.desc); |
| ctrl_ctx = cdnsp_get_input_control_ctx(&pdev->in_ctx); |
| ctrl_ctx->drop_flags = cpu_to_le32(drop_flag); |
| ctrl_ctx->add_flags = 0; |
| |
| cdnsp_endpoint_zero(pdev, pep); |
| |
| if (!(pep->ep_state & EP_UNCONFIGURED)) |
| ret = cdnsp_update_eps_configuration(pdev, pep); |
| |
| cdnsp_free_endpoint_rings(pdev, pep); |
| |
| pep->ep_state &= ~(EP_ENABLED | EP_UNCONFIGURED); |
| pep->ep_state |= EP_STOPPED; |
| |
| finish: |
| trace_cdnsp_ep_disable_end(pep, 0); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| static struct usb_request *cdnsp_gadget_ep_alloc_request(struct usb_ep *ep, |
| gfp_t gfp_flags) |
| { |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); |
| struct cdnsp_request *preq; |
| |
| preq = kzalloc(sizeof(*preq), gfp_flags); |
| if (!preq) |
| return NULL; |
| |
| preq->epnum = pep->number; |
| preq->pep = pep; |
| |
| trace_cdnsp_alloc_request(preq); |
| |
| return &preq->request; |
| } |
| |
| static void cdnsp_gadget_ep_free_request(struct usb_ep *ep, |
| struct usb_request *request) |
| { |
| struct cdnsp_request *preq = to_cdnsp_request(request); |
| |
| trace_cdnsp_free_request(preq); |
| kfree(preq); |
| } |
| |
| static int cdnsp_gadget_ep_queue(struct usb_ep *ep, |
| struct usb_request *request, |
| gfp_t gfp_flags) |
| { |
| struct cdnsp_request *preq; |
| struct cdnsp_device *pdev; |
| struct cdnsp_ep *pep; |
| unsigned long flags; |
| int ret; |
| |
| if (!request || !ep) |
| return -EINVAL; |
| |
| pep = to_cdnsp_ep(ep); |
| pdev = pep->pdev; |
| |
| if (!(pep->ep_state & EP_ENABLED)) { |
| dev_err(pdev->dev, "%s: can't queue to disabled endpoint\n", |
| pep->name); |
| return -EINVAL; |
| } |
| |
| preq = to_cdnsp_request(request); |
| spin_lock_irqsave(&pdev->lock, flags); |
| ret = cdnsp_ep_enqueue(pep, preq); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| static int cdnsp_gadget_ep_dequeue(struct usb_ep *ep, |
| struct usb_request *request) |
| { |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); |
| struct cdnsp_device *pdev = pep->pdev; |
| unsigned long flags; |
| int ret; |
| |
| if (!pep->endpoint.desc) { |
| dev_err(pdev->dev, |
| "%s: can't dequeue to disabled endpoint\n", |
| pep->name); |
| return -ESHUTDOWN; |
| } |
| |
| /* Requests has been dequeued during disabling endpoint. */ |
| if (!(pep->ep_state & EP_ENABLED)) |
| return 0; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| ret = cdnsp_ep_dequeue(pep, to_cdnsp_request(request)); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| static int cdnsp_gadget_ep_set_halt(struct usb_ep *ep, int value) |
| { |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); |
| struct cdnsp_device *pdev = pep->pdev; |
| struct cdnsp_request *preq; |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| |
| preq = next_request(&pep->pending_list); |
| if (value) { |
| if (preq) { |
| trace_cdnsp_ep_busy_try_halt_again(pep, 0); |
| ret = -EAGAIN; |
| goto done; |
| } |
| } |
| |
| ret = cdnsp_halt_endpoint(pdev, pep, value); |
| |
| done: |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| return ret; |
| } |
| |
| static int cdnsp_gadget_ep_set_wedge(struct usb_ep *ep) |
| { |
| struct cdnsp_ep *pep = to_cdnsp_ep(ep); |
| struct cdnsp_device *pdev = pep->pdev; |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| pep->ep_state |= EP_WEDGE; |
| ret = cdnsp_halt_endpoint(pdev, pep, 1); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| static const struct usb_ep_ops cdnsp_gadget_ep0_ops = { |
| .enable = cdnsp_gadget_ep_enable, |
| .disable = cdnsp_gadget_ep_disable, |
| .alloc_request = cdnsp_gadget_ep_alloc_request, |
| .free_request = cdnsp_gadget_ep_free_request, |
| .queue = cdnsp_gadget_ep_queue, |
| .dequeue = cdnsp_gadget_ep_dequeue, |
| .set_halt = cdnsp_gadget_ep_set_halt, |
| .set_wedge = cdnsp_gadget_ep_set_wedge, |
| }; |
| |
| static const struct usb_ep_ops cdnsp_gadget_ep_ops = { |
| .enable = cdnsp_gadget_ep_enable, |
| .disable = cdnsp_gadget_ep_disable, |
| .alloc_request = cdnsp_gadget_ep_alloc_request, |
| .free_request = cdnsp_gadget_ep_free_request, |
| .queue = cdnsp_gadget_ep_queue, |
| .dequeue = cdnsp_gadget_ep_dequeue, |
| .set_halt = cdnsp_gadget_ep_set_halt, |
| .set_wedge = cdnsp_gadget_ep_set_wedge, |
| }; |
| |
| void cdnsp_gadget_giveback(struct cdnsp_ep *pep, |
| struct cdnsp_request *preq, |
| int status) |
| { |
| struct cdnsp_device *pdev = pep->pdev; |
| |
| list_del(&preq->list); |
| |
| if (preq->request.status == -EINPROGRESS) |
| preq->request.status = status; |
| |
| usb_gadget_unmap_request_by_dev(pdev->dev, &preq->request, |
| preq->direction); |
| |
| trace_cdnsp_request_giveback(preq); |
| |
| if (preq != &pdev->ep0_preq) { |
| spin_unlock(&pdev->lock); |
| usb_gadget_giveback_request(&pep->endpoint, &preq->request); |
| spin_lock(&pdev->lock); |
| } |
| } |
| |
| static struct usb_endpoint_descriptor cdnsp_gadget_ep0_desc = { |
| .bLength = USB_DT_ENDPOINT_SIZE, |
| .bDescriptorType = USB_DT_ENDPOINT, |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, |
| }; |
| |
| static int cdnsp_run(struct cdnsp_device *pdev, |
| enum usb_device_speed speed) |
| { |
| u32 fs_speed = 0; |
| u32 temp; |
| int ret; |
| |
| temp = readl(&pdev->ir_set->irq_control); |
| temp &= ~IMOD_INTERVAL_MASK; |
| temp |= ((IMOD_DEFAULT_INTERVAL / 250) & IMOD_INTERVAL_MASK); |
| writel(temp, &pdev->ir_set->irq_control); |
| |
| temp = readl(&pdev->port3x_regs->mode_addr); |
| |
| switch (speed) { |
| case USB_SPEED_SUPER_PLUS: |
| temp |= CFG_3XPORT_SSP_SUPPORT; |
| break; |
| case USB_SPEED_SUPER: |
| temp &= ~CFG_3XPORT_SSP_SUPPORT; |
| break; |
| case USB_SPEED_HIGH: |
| break; |
| case USB_SPEED_FULL: |
| fs_speed = PORT_REG6_FORCE_FS; |
| break; |
| default: |
| dev_err(pdev->dev, "invalid maximum_speed parameter %d\n", |
| speed); |
| fallthrough; |
| case USB_SPEED_UNKNOWN: |
| /* Default to superspeed. */ |
| speed = USB_SPEED_SUPER; |
| break; |
| } |
| |
| if (speed >= USB_SPEED_SUPER) { |
| writel(temp, &pdev->port3x_regs->mode_addr); |
| cdnsp_set_link_state(pdev, &pdev->usb3_port.regs->portsc, |
| XDEV_RXDETECT); |
| } else { |
| cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc); |
| } |
| |
| cdnsp_set_link_state(pdev, &pdev->usb2_port.regs->portsc, |
| XDEV_RXDETECT); |
| |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512); |
| |
| writel(PORT_REG6_L1_L0_HW_EN | fs_speed, &pdev->port20_regs->port_reg6); |
| |
| ret = cdnsp_start(pdev); |
| if (ret) { |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| temp = readl(&pdev->op_regs->command); |
| temp |= (CMD_INTE); |
| writel(temp, &pdev->op_regs->command); |
| |
| temp = readl(&pdev->ir_set->irq_pending); |
| writel(IMAN_IE_SET(temp), &pdev->ir_set->irq_pending); |
| |
| trace_cdnsp_init("Controller ready to work"); |
| return 0; |
| err: |
| cdnsp_halt(pdev); |
| return ret; |
| } |
| |
| static int cdnsp_gadget_udc_start(struct usb_gadget *g, |
| struct usb_gadget_driver *driver) |
| { |
| enum usb_device_speed max_speed = driver->max_speed; |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| pdev->gadget_driver = driver; |
| |
| /* limit speed if necessary */ |
| max_speed = min(driver->max_speed, g->max_speed); |
| ret = cdnsp_run(pdev, max_speed); |
| |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| /* |
| * Update Event Ring Dequeue Pointer: |
| * - When all events have finished |
| * - To avoid "Event Ring Full Error" condition |
| */ |
| void cdnsp_update_erst_dequeue(struct cdnsp_device *pdev, |
| union cdnsp_trb *event_ring_deq, |
| u8 clear_ehb) |
| { |
| u64 temp_64; |
| dma_addr_t deq; |
| |
| temp_64 = cdnsp_read_64(&pdev->ir_set->erst_dequeue); |
| |
| /* If necessary, update the HW's version of the event ring deq ptr. */ |
| if (event_ring_deq != pdev->event_ring->dequeue) { |
| deq = cdnsp_trb_virt_to_dma(pdev->event_ring->deq_seg, |
| pdev->event_ring->dequeue); |
| temp_64 &= ERST_PTR_MASK; |
| temp_64 |= ((u64)deq & (u64)~ERST_PTR_MASK); |
| } |
| |
| /* Clear the event handler busy flag (RW1C). */ |
| if (clear_ehb) |
| temp_64 |= ERST_EHB; |
| else |
| temp_64 &= ~ERST_EHB; |
| |
| cdnsp_write_64(temp_64, &pdev->ir_set->erst_dequeue); |
| } |
| |
| static void cdnsp_clear_cmd_ring(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_segment *seg; |
| u64 val_64; |
| int i; |
| |
| cdnsp_initialize_ring_info(pdev->cmd_ring); |
| |
| seg = pdev->cmd_ring->first_seg; |
| for (i = 0; i < pdev->cmd_ring->num_segs; i++) { |
| memset(seg->trbs, 0, |
| sizeof(union cdnsp_trb) * (TRBS_PER_SEGMENT - 1)); |
| seg = seg->next; |
| } |
| |
| /* Set the address in the Command Ring Control register. */ |
| val_64 = cdnsp_read_64(&pdev->op_regs->cmd_ring); |
| val_64 = (val_64 & (u64)CMD_RING_RSVD_BITS) | |
| (pdev->cmd_ring->first_seg->dma & (u64)~CMD_RING_RSVD_BITS) | |
| pdev->cmd_ring->cycle_state; |
| cdnsp_write_64(val_64, &pdev->op_regs->cmd_ring); |
| } |
| |
| static void cdnsp_consume_all_events(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_segment *event_deq_seg; |
| union cdnsp_trb *event_ring_deq; |
| union cdnsp_trb *event; |
| u32 cycle_bit; |
| |
| event_ring_deq = pdev->event_ring->dequeue; |
| event_deq_seg = pdev->event_ring->deq_seg; |
| event = pdev->event_ring->dequeue; |
| |
| /* Update ring dequeue pointer. */ |
| while (1) { |
| cycle_bit = (le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE); |
| |
| /* Does the controller or driver own the TRB? */ |
| if (cycle_bit != pdev->event_ring->cycle_state) |
| break; |
| |
| cdnsp_inc_deq(pdev, pdev->event_ring); |
| |
| if (!cdnsp_last_trb_on_seg(event_deq_seg, event)) { |
| event++; |
| continue; |
| } |
| |
| if (cdnsp_last_trb_on_ring(pdev->event_ring, event_deq_seg, |
| event)) |
| cycle_bit ^= 1; |
| |
| event_deq_seg = event_deq_seg->next; |
| event = event_deq_seg->trbs; |
| } |
| |
| cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1); |
| } |
| |
| static void cdnsp_stop(struct cdnsp_device *pdev) |
| { |
| u32 temp; |
| |
| cdnsp_cmd_flush_ep(pdev, &pdev->eps[0]); |
| |
| /* Remove internally queued request for ep0. */ |
| if (!list_empty(&pdev->eps[0].pending_list)) { |
| struct cdnsp_request *req; |
| |
| req = next_request(&pdev->eps[0].pending_list); |
| if (req == &pdev->ep0_preq) |
| cdnsp_ep_dequeue(&pdev->eps[0], req); |
| } |
| |
| cdnsp_disable_port(pdev, &pdev->usb2_port.regs->portsc); |
| cdnsp_disable_port(pdev, &pdev->usb3_port.regs->portsc); |
| cdnsp_disable_slot(pdev); |
| cdnsp_halt(pdev); |
| |
| temp = readl(&pdev->op_regs->status); |
| writel((temp & ~0x1fff) | STS_EINT, &pdev->op_regs->status); |
| temp = readl(&pdev->ir_set->irq_pending); |
| writel(IMAN_IE_CLEAR(temp), &pdev->ir_set->irq_pending); |
| |
| cdnsp_clear_port_change_bit(pdev, &pdev->usb2_port.regs->portsc); |
| cdnsp_clear_port_change_bit(pdev, &pdev->usb3_port.regs->portsc); |
| |
| /* Clear interrupt line */ |
| temp = readl(&pdev->ir_set->irq_pending); |
| temp |= IMAN_IP; |
| writel(temp, &pdev->ir_set->irq_pending); |
| |
| cdnsp_consume_all_events(pdev); |
| cdnsp_clear_cmd_ring(pdev); |
| |
| trace_cdnsp_exit("Controller stopped."); |
| } |
| |
| /* |
| * Stop controller. |
| * This function is called by the gadget core when the driver is removed. |
| * Disable slot, disable IRQs, and quiesce the controller. |
| */ |
| static int cdnsp_gadget_udc_stop(struct usb_gadget *g) |
| { |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| cdnsp_stop(pdev); |
| pdev->gadget_driver = NULL; |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return 0; |
| } |
| |
| static int cdnsp_gadget_get_frame(struct usb_gadget *g) |
| { |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); |
| |
| return cdnsp_get_frame(pdev); |
| } |
| |
| static void __cdnsp_gadget_wakeup(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_port_regs __iomem *port_regs; |
| u32 portpm, portsc; |
| |
| port_regs = pdev->active_port->regs; |
| portsc = readl(&port_regs->portsc) & PORT_PLS_MASK; |
| |
| /* Remote wakeup feature is not enabled by host. */ |
| if (pdev->gadget.speed < USB_SPEED_SUPER && portsc == XDEV_U2) { |
| portpm = readl(&port_regs->portpmsc); |
| |
| if (!(portpm & PORT_RWE)) |
| return; |
| } |
| |
| if (portsc == XDEV_U3 && !pdev->may_wakeup) |
| return; |
| |
| cdnsp_set_link_state(pdev, &port_regs->portsc, XDEV_U0); |
| |
| pdev->cdnsp_state |= CDNSP_WAKEUP_PENDING; |
| } |
| |
| static int cdnsp_gadget_wakeup(struct usb_gadget *g) |
| { |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| __cdnsp_gadget_wakeup(pdev); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return 0; |
| } |
| |
| static int cdnsp_gadget_set_selfpowered(struct usb_gadget *g, |
| int is_selfpowered) |
| { |
| struct cdnsp_device *pdev = gadget_to_cdnsp(g); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| g->is_selfpowered = !!is_selfpowered; |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return 0; |
| } |
| |
| static int cdnsp_gadget_pullup(struct usb_gadget *gadget, int is_on) |
| { |
| struct cdnsp_device *pdev = gadget_to_cdnsp(gadget); |
| struct cdns *cdns = dev_get_drvdata(pdev->dev); |
| unsigned long flags; |
| |
| trace_cdnsp_pullup(is_on); |
| |
| /* |
| * Disable events handling while controller is being |
| * enabled/disabled. |
| */ |
| disable_irq(cdns->dev_irq); |
| spin_lock_irqsave(&pdev->lock, flags); |
| |
| if (!is_on) { |
| cdnsp_reset_device(pdev); |
| cdns_clear_vbus(cdns); |
| } else { |
| cdns_set_vbus(cdns); |
| } |
| |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| enable_irq(cdns->dev_irq); |
| |
| return 0; |
| } |
| |
| static const struct usb_gadget_ops cdnsp_gadget_ops = { |
| .get_frame = cdnsp_gadget_get_frame, |
| .wakeup = cdnsp_gadget_wakeup, |
| .set_selfpowered = cdnsp_gadget_set_selfpowered, |
| .pullup = cdnsp_gadget_pullup, |
| .udc_start = cdnsp_gadget_udc_start, |
| .udc_stop = cdnsp_gadget_udc_stop, |
| }; |
| |
| static void cdnsp_get_ep_buffering(struct cdnsp_device *pdev, |
| struct cdnsp_ep *pep) |
| { |
| void __iomem *reg = &pdev->cap_regs->hc_capbase; |
| int endpoints; |
| |
| reg += cdnsp_find_next_ext_cap(reg, 0, XBUF_CAP_ID); |
| |
| if (!pep->direction) { |
| pep->buffering = readl(reg + XBUF_RX_TAG_MASK_0_OFFSET); |
| pep->buffering_period = readl(reg + XBUF_RX_TAG_MASK_1_OFFSET); |
| pep->buffering = (pep->buffering + 1) / 2; |
| pep->buffering_period = (pep->buffering_period + 1) / 2; |
| return; |
| } |
| |
| endpoints = HCS_ENDPOINTS(pdev->hcs_params1) / 2; |
| |
| /* Set to XBUF_TX_TAG_MASK_0 register. */ |
| reg += XBUF_TX_CMD_OFFSET + (endpoints * 2 + 2) * sizeof(u32); |
| /* Set reg to XBUF_TX_TAG_MASK_N related with this endpoint. */ |
| reg += pep->number * sizeof(u32) * 2; |
| |
| pep->buffering = (readl(reg) + 1) / 2; |
| pep->buffering_period = pep->buffering; |
| } |
| |
| static int cdnsp_gadget_init_endpoints(struct cdnsp_device *pdev) |
| { |
| int max_streams = HCC_MAX_PSA(pdev->hcc_params); |
| struct cdnsp_ep *pep; |
| int i; |
| |
| INIT_LIST_HEAD(&pdev->gadget.ep_list); |
| |
| if (max_streams < STREAM_LOG_STREAMS) { |
| dev_err(pdev->dev, "Stream size %d not supported\n", |
| max_streams); |
| return -EINVAL; |
| } |
| |
| max_streams = STREAM_LOG_STREAMS; |
| |
| for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) { |
| bool direction = !(i & 1); /* Start from OUT endpoint. */ |
| u8 epnum = ((i + 1) >> 1); |
| |
| if (!CDNSP_IF_EP_EXIST(pdev, epnum, direction)) |
| continue; |
| |
| pep = &pdev->eps[i]; |
| pep->pdev = pdev; |
| pep->number = epnum; |
| pep->direction = direction; /* 0 for OUT, 1 for IN. */ |
| |
| /* |
| * Ep0 is bidirectional, so ep0in and ep0out are represented by |
| * pdev->eps[0] |
| */ |
| if (epnum == 0) { |
| snprintf(pep->name, sizeof(pep->name), "ep%d%s", |
| epnum, "BiDir"); |
| |
| pep->idx = 0; |
| usb_ep_set_maxpacket_limit(&pep->endpoint, 512); |
| pep->endpoint.maxburst = 1; |
| pep->endpoint.ops = &cdnsp_gadget_ep0_ops; |
| pep->endpoint.desc = &cdnsp_gadget_ep0_desc; |
| pep->endpoint.comp_desc = NULL; |
| pep->endpoint.caps.type_control = true; |
| pep->endpoint.caps.dir_in = true; |
| pep->endpoint.caps.dir_out = true; |
| |
| pdev->ep0_preq.epnum = pep->number; |
| pdev->ep0_preq.pep = pep; |
| pdev->gadget.ep0 = &pep->endpoint; |
| } else { |
| snprintf(pep->name, sizeof(pep->name), "ep%d%s", |
| epnum, (pep->direction) ? "in" : "out"); |
| |
| pep->idx = (epnum * 2 + (direction ? 1 : 0)) - 1; |
| usb_ep_set_maxpacket_limit(&pep->endpoint, 1024); |
| |
| pep->endpoint.max_streams = max_streams; |
| pep->endpoint.ops = &cdnsp_gadget_ep_ops; |
| list_add_tail(&pep->endpoint.ep_list, |
| &pdev->gadget.ep_list); |
| |
| pep->endpoint.caps.type_iso = true; |
| pep->endpoint.caps.type_bulk = true; |
| pep->endpoint.caps.type_int = true; |
| |
| pep->endpoint.caps.dir_in = direction; |
| pep->endpoint.caps.dir_out = !direction; |
| } |
| |
| pep->endpoint.name = pep->name; |
| pep->in_ctx = cdnsp_get_ep_ctx(&pdev->in_ctx, pep->idx); |
| pep->out_ctx = cdnsp_get_ep_ctx(&pdev->out_ctx, pep->idx); |
| cdnsp_get_ep_buffering(pdev, pep); |
| |
| dev_dbg(pdev->dev, "Init %s, MPS: %04x SupType: " |
| "CTRL: %s, INT: %s, BULK: %s, ISOC %s, " |
| "SupDir IN: %s, OUT: %s\n", |
| pep->name, 1024, |
| (pep->endpoint.caps.type_control) ? "yes" : "no", |
| (pep->endpoint.caps.type_int) ? "yes" : "no", |
| (pep->endpoint.caps.type_bulk) ? "yes" : "no", |
| (pep->endpoint.caps.type_iso) ? "yes" : "no", |
| (pep->endpoint.caps.dir_in) ? "yes" : "no", |
| (pep->endpoint.caps.dir_out) ? "yes" : "no"); |
| |
| INIT_LIST_HEAD(&pep->pending_list); |
| } |
| |
| return 0; |
| } |
| |
| static void cdnsp_gadget_free_endpoints(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_ep *pep; |
| int i; |
| |
| for (i = 0; i < CDNSP_ENDPOINTS_NUM; i++) { |
| pep = &pdev->eps[i]; |
| if (pep->number != 0 && pep->out_ctx) |
| list_del(&pep->endpoint.ep_list); |
| } |
| } |
| |
| void cdnsp_disconnect_gadget(struct cdnsp_device *pdev) |
| { |
| pdev->cdnsp_state |= CDNSP_STATE_DISCONNECT_PENDING; |
| |
| if (pdev->gadget_driver && pdev->gadget_driver->disconnect) { |
| spin_unlock(&pdev->lock); |
| pdev->gadget_driver->disconnect(&pdev->gadget); |
| spin_lock(&pdev->lock); |
| } |
| |
| pdev->gadget.speed = USB_SPEED_UNKNOWN; |
| usb_gadget_set_state(&pdev->gadget, USB_STATE_NOTATTACHED); |
| |
| pdev->cdnsp_state &= ~CDNSP_STATE_DISCONNECT_PENDING; |
| } |
| |
| void cdnsp_suspend_gadget(struct cdnsp_device *pdev) |
| { |
| if (pdev->gadget_driver && pdev->gadget_driver->suspend) { |
| spin_unlock(&pdev->lock); |
| pdev->gadget_driver->suspend(&pdev->gadget); |
| spin_lock(&pdev->lock); |
| } |
| } |
| |
| void cdnsp_resume_gadget(struct cdnsp_device *pdev) |
| { |
| if (pdev->gadget_driver && pdev->gadget_driver->resume) { |
| spin_unlock(&pdev->lock); |
| pdev->gadget_driver->resume(&pdev->gadget); |
| spin_lock(&pdev->lock); |
| } |
| } |
| |
| void cdnsp_irq_reset(struct cdnsp_device *pdev) |
| { |
| struct cdnsp_port_regs __iomem *port_regs; |
| |
| cdnsp_reset_device(pdev); |
| |
| port_regs = pdev->active_port->regs; |
| pdev->gadget.speed = cdnsp_port_speed(readl(port_regs)); |
| |
| spin_unlock(&pdev->lock); |
| usb_gadget_udc_reset(&pdev->gadget, pdev->gadget_driver); |
| spin_lock(&pdev->lock); |
| |
| switch (pdev->gadget.speed) { |
| case USB_SPEED_SUPER_PLUS: |
| case USB_SPEED_SUPER: |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(512); |
| pdev->gadget.ep0->maxpacket = 512; |
| break; |
| case USB_SPEED_HIGH: |
| case USB_SPEED_FULL: |
| cdnsp_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(64); |
| pdev->gadget.ep0->maxpacket = 64; |
| break; |
| default: |
| /* Low speed is not supported. */ |
| dev_err(pdev->dev, "Unknown device speed\n"); |
| break; |
| } |
| |
| cdnsp_clear_chicken_bits_2(pdev, CHICKEN_XDMA_2_TP_CACHE_DIS); |
| cdnsp_setup_device(pdev, SETUP_CONTEXT_ONLY); |
| usb_gadget_set_state(&pdev->gadget, USB_STATE_DEFAULT); |
| } |
| |
| static void cdnsp_get_rev_cap(struct cdnsp_device *pdev) |
| { |
| void __iomem *reg = &pdev->cap_regs->hc_capbase; |
| |
| reg += cdnsp_find_next_ext_cap(reg, 0, RTL_REV_CAP); |
| pdev->rev_cap = reg; |
| |
| dev_info(pdev->dev, "Rev: %08x/%08x, eps: %08x, buff: %08x/%08x\n", |
| readl(&pdev->rev_cap->ctrl_revision), |
| readl(&pdev->rev_cap->rtl_revision), |
| readl(&pdev->rev_cap->ep_supported), |
| readl(&pdev->rev_cap->rx_buff_size), |
| readl(&pdev->rev_cap->tx_buff_size)); |
| } |
| |
| static int cdnsp_gen_setup(struct cdnsp_device *pdev) |
| { |
| int ret; |
| u32 reg; |
| |
| pdev->cap_regs = pdev->regs; |
| pdev->op_regs = pdev->regs + |
| HC_LENGTH(readl(&pdev->cap_regs->hc_capbase)); |
| pdev->run_regs = pdev->regs + |
| (readl(&pdev->cap_regs->run_regs_off) & RTSOFF_MASK); |
| |
| /* Cache read-only capability registers */ |
| pdev->hcs_params1 = readl(&pdev->cap_regs->hcs_params1); |
| pdev->hcc_params = readl(&pdev->cap_regs->hc_capbase); |
| pdev->hci_version = HC_VERSION(pdev->hcc_params); |
| pdev->hcc_params = readl(&pdev->cap_regs->hcc_params); |
| |
| cdnsp_get_rev_cap(pdev); |
| |
| /* Make sure the Device Controller is halted. */ |
| ret = cdnsp_halt(pdev); |
| if (ret) |
| return ret; |
| |
| /* Reset the internal controller memory state and registers. */ |
| ret = cdnsp_reset(pdev); |
| if (ret) |
| return ret; |
| |
| /* |
| * Set dma_mask and coherent_dma_mask to 64-bits, |
| * if controller supports 64-bit addressing. |
| */ |
| if (HCC_64BIT_ADDR(pdev->hcc_params) && |
| !dma_set_mask(pdev->dev, DMA_BIT_MASK(64))) { |
| dev_dbg(pdev->dev, "Enabling 64-bit DMA addresses.\n"); |
| dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(64)); |
| } else { |
| /* |
| * This is to avoid error in cases where a 32-bit USB |
| * controller is used on a 64-bit capable system. |
| */ |
| ret = dma_set_mask(pdev->dev, DMA_BIT_MASK(32)); |
| if (ret) |
| return ret; |
| |
| dev_dbg(pdev->dev, "Enabling 32-bit DMA addresses.\n"); |
| dma_set_coherent_mask(pdev->dev, DMA_BIT_MASK(32)); |
| } |
| |
| spin_lock_init(&pdev->lock); |
| |
| ret = cdnsp_mem_init(pdev); |
| if (ret) |
| return ret; |
| |
| /* |
| * Software workaround for U1: after transition |
| * to U1 the controller starts gating clock, and in some cases, |
| * it causes that controller stack. |
| */ |
| reg = readl(&pdev->port3x_regs->mode_2); |
| reg &= ~CFG_3XPORT_U1_PIPE_CLK_GATE_EN; |
| writel(reg, &pdev->port3x_regs->mode_2); |
| |
| return 0; |
| } |
| |
| static int __cdnsp_gadget_init(struct cdns *cdns) |
| { |
| struct cdnsp_device *pdev; |
| u32 max_speed; |
| int ret = -ENOMEM; |
| |
| cdns_drd_gadget_on(cdns); |
| |
| pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); |
| if (!pdev) |
| return -ENOMEM; |
| |
| pm_runtime_get_sync(cdns->dev); |
| |
| cdns->gadget_dev = pdev; |
| pdev->dev = cdns->dev; |
| pdev->regs = cdns->dev_regs; |
| max_speed = usb_get_maximum_speed(cdns->dev); |
| |
| switch (max_speed) { |
| case USB_SPEED_FULL: |
| case USB_SPEED_HIGH: |
| case USB_SPEED_SUPER: |
| case USB_SPEED_SUPER_PLUS: |
| break; |
| default: |
| dev_err(cdns->dev, "invalid speed parameter %d\n", max_speed); |
| fallthrough; |
| case USB_SPEED_UNKNOWN: |
| /* Default to SSP */ |
| max_speed = USB_SPEED_SUPER_PLUS; |
| break; |
| } |
| |
| pdev->gadget.ops = &cdnsp_gadget_ops; |
| pdev->gadget.name = "cdnsp-gadget"; |
| pdev->gadget.speed = USB_SPEED_UNKNOWN; |
| pdev->gadget.sg_supported = 1; |
| pdev->gadget.max_speed = max_speed; |
| pdev->gadget.lpm_capable = 1; |
| |
| pdev->setup_buf = kzalloc(CDNSP_EP0_SETUP_SIZE, GFP_KERNEL); |
| if (!pdev->setup_buf) |
| goto free_pdev; |
| |
| /* |
| * Controller supports not aligned buffer but it should improve |
| * performance. |
| */ |
| pdev->gadget.quirk_ep_out_aligned_size = true; |
| |
| ret = cdnsp_gen_setup(pdev); |
| if (ret) { |
| dev_err(pdev->dev, "Generic initialization failed %d\n", ret); |
| goto free_setup; |
| } |
| |
| ret = cdnsp_gadget_init_endpoints(pdev); |
| if (ret) { |
| dev_err(pdev->dev, "failed to initialize endpoints\n"); |
| goto halt_pdev; |
| } |
| |
| ret = usb_add_gadget_udc(pdev->dev, &pdev->gadget); |
| if (ret) { |
| dev_err(pdev->dev, "failed to register udc\n"); |
| goto free_endpoints; |
| } |
| |
| ret = devm_request_threaded_irq(pdev->dev, cdns->dev_irq, |
| cdnsp_irq_handler, |
| cdnsp_thread_irq_handler, IRQF_SHARED, |
| dev_name(pdev->dev), pdev); |
| if (ret) |
| goto del_gadget; |
| |
| return 0; |
| |
| del_gadget: |
| usb_del_gadget_udc(&pdev->gadget); |
| free_endpoints: |
| cdnsp_gadget_free_endpoints(pdev); |
| halt_pdev: |
| cdnsp_halt(pdev); |
| cdnsp_reset(pdev); |
| cdnsp_mem_cleanup(pdev); |
| free_setup: |
| kfree(pdev->setup_buf); |
| free_pdev: |
| kfree(pdev); |
| |
| return ret; |
| } |
| |
| static void cdnsp_gadget_exit(struct cdns *cdns) |
| { |
| struct cdnsp_device *pdev = cdns->gadget_dev; |
| |
| devm_free_irq(pdev->dev, cdns->dev_irq, pdev); |
| pm_runtime_mark_last_busy(cdns->dev); |
| pm_runtime_put_autosuspend(cdns->dev); |
| usb_del_gadget_udc(&pdev->gadget); |
| cdnsp_gadget_free_endpoints(pdev); |
| cdnsp_mem_cleanup(pdev); |
| kfree(pdev); |
| cdns->gadget_dev = NULL; |
| cdns_drd_gadget_off(cdns); |
| } |
| |
| static int cdnsp_gadget_suspend(struct cdns *cdns, bool do_wakeup) |
| { |
| struct cdnsp_device *pdev = cdns->gadget_dev; |
| unsigned long flags; |
| |
| if (pdev->link_state == XDEV_U3) |
| return 0; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| cdnsp_disconnect_gadget(pdev); |
| cdnsp_stop(pdev); |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return 0; |
| } |
| |
| static int cdnsp_gadget_resume(struct cdns *cdns, bool hibernated) |
| { |
| struct cdnsp_device *pdev = cdns->gadget_dev; |
| enum usb_device_speed max_speed; |
| unsigned long flags; |
| int ret; |
| |
| if (!pdev->gadget_driver) |
| return 0; |
| |
| spin_lock_irqsave(&pdev->lock, flags); |
| max_speed = pdev->gadget_driver->max_speed; |
| |
| /* Limit speed if necessary. */ |
| max_speed = min(max_speed, pdev->gadget.max_speed); |
| |
| ret = cdnsp_run(pdev, max_speed); |
| |
| if (pdev->link_state == XDEV_U3) |
| __cdnsp_gadget_wakeup(pdev); |
| |
| spin_unlock_irqrestore(&pdev->lock, flags); |
| |
| return ret; |
| } |
| |
| /** |
| * cdnsp_gadget_init - initialize device structure |
| * @cdns: cdnsp instance |
| * |
| * This function initializes the gadget. |
| */ |
| int cdnsp_gadget_init(struct cdns *cdns) |
| { |
| struct cdns_role_driver *rdrv; |
| |
| rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL); |
| if (!rdrv) |
| return -ENOMEM; |
| |
| rdrv->start = __cdnsp_gadget_init; |
| rdrv->stop = cdnsp_gadget_exit; |
| rdrv->suspend = cdnsp_gadget_suspend; |
| rdrv->resume = cdnsp_gadget_resume; |
| rdrv->state = CDNS_ROLE_STATE_INACTIVE; |
| rdrv->name = "gadget"; |
| cdns->roles[USB_ROLE_DEVICE] = rdrv; |
| |
| return 0; |
| } |