| /* |
| * STMicroelectronics st_lsm6dsx i2c controller driver |
| * |
| * i2c controller embedded in lsm6dx series can connect up to four |
| * slave devices using accelerometer sensor as trigger for i2c |
| * read/write operations. Current implementation relies on SLV0 channel |
| * for slave configuration and SLV{1,2,3} to read data and push them into |
| * the hw FIFO |
| * |
| * Copyright (C) 2018 Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| * |
| */ |
| #include <linux/module.h> |
| #include <linux/regmap.h> |
| #include <linux/iio/iio.h> |
| #include <linux/iio/sysfs.h> |
| #include <linux/bitfield.h> |
| |
| #include "st_lsm6dsx.h" |
| |
| #define ST_LSM6DSX_SLV_ADDR(n, base) ((base) + (n) * 3) |
| #define ST_LSM6DSX_SLV_SUB_ADDR(n, base) ((base) + 1 + (n) * 3) |
| #define ST_LSM6DSX_SLV_CONFIG(n, base) ((base) + 2 + (n) * 3) |
| |
| #define ST_LS6DSX_READ_OP_MASK GENMASK(2, 0) |
| |
| static const struct st_lsm6dsx_ext_dev_settings st_lsm6dsx_ext_dev_table[] = { |
| /* LIS2MDL */ |
| { |
| .i2c_addr = { 0x1e }, |
| .wai = { |
| .addr = 0x4f, |
| .val = 0x40, |
| }, |
| .id = ST_LSM6DSX_ID_MAGN, |
| .odr_table = { |
| .reg = { |
| .addr = 0x60, |
| .mask = GENMASK(3, 2), |
| }, |
| .odr_avl[0] = { 10000, 0x0 }, |
| .odr_avl[1] = { 20000, 0x1 }, |
| .odr_avl[2] = { 50000, 0x2 }, |
| .odr_avl[3] = { 100000, 0x3 }, |
| .odr_len = 4, |
| }, |
| .fs_table = { |
| .fs_avl[0] = { |
| .gain = 1500, |
| .val = 0x0, |
| }, /* 1500 uG/LSB */ |
| .fs_len = 1, |
| }, |
| .temp_comp = { |
| .addr = 0x60, |
| .mask = BIT(7), |
| }, |
| .pwr_table = { |
| .reg = { |
| .addr = 0x60, |
| .mask = GENMASK(1, 0), |
| }, |
| .off_val = 0x2, |
| .on_val = 0x0, |
| }, |
| .off_canc = { |
| .addr = 0x61, |
| .mask = BIT(1), |
| }, |
| .bdu = { |
| .addr = 0x62, |
| .mask = BIT(4), |
| }, |
| .out = { |
| .addr = 0x68, |
| .len = 6, |
| }, |
| }, |
| /* LIS3MDL */ |
| { |
| .i2c_addr = { 0x1e }, |
| .wai = { |
| .addr = 0x0f, |
| .val = 0x3d, |
| }, |
| .id = ST_LSM6DSX_ID_MAGN, |
| .odr_table = { |
| .reg = { |
| .addr = 0x20, |
| .mask = GENMASK(4, 2), |
| }, |
| .odr_avl[0] = { 1000, 0x0 }, |
| .odr_avl[1] = { 2000, 0x1 }, |
| .odr_avl[2] = { 3000, 0x2 }, |
| .odr_avl[3] = { 5000, 0x3 }, |
| .odr_avl[4] = { 10000, 0x4 }, |
| .odr_avl[5] = { 20000, 0x5 }, |
| .odr_avl[6] = { 40000, 0x6 }, |
| .odr_avl[7] = { 80000, 0x7 }, |
| .odr_len = 8, |
| }, |
| .fs_table = { |
| .reg = { |
| .addr = 0x21, |
| .mask = GENMASK(6, 5), |
| }, |
| .fs_avl[0] = { |
| .gain = 146, |
| .val = 0x00, |
| }, /* 4000 uG/LSB */ |
| .fs_avl[1] = { |
| .gain = 292, |
| .val = 0x01, |
| }, /* 8000 uG/LSB */ |
| .fs_avl[2] = { |
| .gain = 438, |
| .val = 0x02, |
| }, /* 12000 uG/LSB */ |
| .fs_avl[3] = { |
| .gain = 584, |
| .val = 0x03, |
| }, /* 16000 uG/LSB */ |
| .fs_len = 4, |
| }, |
| .pwr_table = { |
| .reg = { |
| .addr = 0x22, |
| .mask = GENMASK(1, 0), |
| }, |
| .off_val = 0x2, |
| .on_val = 0x0, |
| }, |
| .bdu = { |
| .addr = 0x24, |
| .mask = BIT(6), |
| }, |
| .out = { |
| .addr = 0x28, |
| .len = 6, |
| }, |
| }, |
| }; |
| |
| static void st_lsm6dsx_shub_wait_complete(struct st_lsm6dsx_hw *hw) |
| { |
| struct st_lsm6dsx_sensor *sensor; |
| u32 odr, timeout; |
| |
| sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); |
| odr = (hw->enable_mask & BIT(ST_LSM6DSX_ID_ACC)) ? sensor->odr : 12500; |
| /* set 10ms as minimum timeout for i2c slave configuration */ |
| timeout = max_t(u32, 2000000U / odr + 1, 10); |
| msleep(timeout); |
| } |
| |
| /* |
| * st_lsm6dsx_shub_read_output - read i2c controller register |
| * |
| * Read st_lsm6dsx i2c controller register |
| */ |
| static int |
| st_lsm6dsx_shub_read_output(struct st_lsm6dsx_hw *hw, u8 *data, |
| int len) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| int err; |
| |
| mutex_lock(&hw->page_lock); |
| |
| hub_settings = &hw->settings->shub_settings; |
| if (hub_settings->shub_out.sec_page) { |
| err = st_lsm6dsx_set_page(hw, true); |
| if (err < 0) |
| goto out; |
| } |
| |
| err = regmap_bulk_read(hw->regmap, hub_settings->shub_out.addr, |
| data, len); |
| |
| if (hub_settings->shub_out.sec_page) |
| st_lsm6dsx_set_page(hw, false); |
| out: |
| mutex_unlock(&hw->page_lock); |
| |
| return err; |
| } |
| |
| /* |
| * st_lsm6dsx_shub_write_reg - write i2c controller register |
| * |
| * Write st_lsm6dsx i2c controller register |
| */ |
| static int st_lsm6dsx_shub_write_reg(struct st_lsm6dsx_hw *hw, u8 addr, |
| u8 *data, int len) |
| { |
| int err; |
| |
| mutex_lock(&hw->page_lock); |
| err = st_lsm6dsx_set_page(hw, true); |
| if (err < 0) |
| goto out; |
| |
| err = regmap_bulk_write(hw->regmap, addr, data, len); |
| |
| st_lsm6dsx_set_page(hw, false); |
| out: |
| mutex_unlock(&hw->page_lock); |
| |
| return err; |
| } |
| |
| static int |
| st_lsm6dsx_shub_write_reg_with_mask(struct st_lsm6dsx_hw *hw, u8 addr, |
| u8 mask, u8 val) |
| { |
| int err; |
| |
| mutex_lock(&hw->page_lock); |
| err = st_lsm6dsx_set_page(hw, true); |
| if (err < 0) |
| goto out; |
| |
| err = regmap_update_bits(hw->regmap, addr, mask, val); |
| |
| st_lsm6dsx_set_page(hw, false); |
| out: |
| mutex_unlock(&hw->page_lock); |
| |
| return err; |
| } |
| |
| static int st_lsm6dsx_shub_master_enable(struct st_lsm6dsx_sensor *sensor, |
| bool enable) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| struct st_lsm6dsx_hw *hw = sensor->hw; |
| unsigned int data; |
| int err; |
| |
| /* enable acc sensor as trigger */ |
| err = st_lsm6dsx_sensor_set_enable(sensor, enable); |
| if (err < 0) |
| return err; |
| |
| mutex_lock(&hw->page_lock); |
| |
| hub_settings = &hw->settings->shub_settings; |
| if (hub_settings->master_en.sec_page) { |
| err = st_lsm6dsx_set_page(hw, true); |
| if (err < 0) |
| goto out; |
| } |
| |
| data = ST_LSM6DSX_SHIFT_VAL(enable, hub_settings->master_en.mask); |
| err = regmap_update_bits(hw->regmap, hub_settings->master_en.addr, |
| hub_settings->master_en.mask, data); |
| |
| if (hub_settings->master_en.sec_page) |
| st_lsm6dsx_set_page(hw, false); |
| out: |
| mutex_unlock(&hw->page_lock); |
| |
| return err; |
| } |
| |
| /* |
| * st_lsm6dsx_shub_read - read data from slave device register |
| * |
| * Read data from slave device register. SLV0 is used for |
| * one-shot read operation |
| */ |
| static int |
| st_lsm6dsx_shub_read(struct st_lsm6dsx_sensor *sensor, u8 addr, |
| u8 *data, int len) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| u8 config[3], slv_addr, slv_config = 0; |
| struct st_lsm6dsx_hw *hw = sensor->hw; |
| const struct st_lsm6dsx_reg *aux_sens; |
| int err; |
| |
| hub_settings = &hw->settings->shub_settings; |
| slv_addr = ST_LSM6DSX_SLV_ADDR(0, hub_settings->slv0_addr); |
| aux_sens = &hw->settings->shub_settings.aux_sens; |
| /* do not overwrite aux_sens */ |
| if (slv_addr + 2 == aux_sens->addr) |
| slv_config = ST_LSM6DSX_SHIFT_VAL(3, aux_sens->mask); |
| |
| config[0] = (sensor->ext_info.addr << 1) | 1; |
| config[1] = addr; |
| config[2] = (len & ST_LS6DSX_READ_OP_MASK) | slv_config; |
| |
| err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| if (err < 0) |
| return err; |
| |
| err = st_lsm6dsx_shub_master_enable(sensor, true); |
| if (err < 0) |
| return err; |
| |
| st_lsm6dsx_shub_wait_complete(hw); |
| |
| err = st_lsm6dsx_shub_read_output(hw, data, |
| len & ST_LS6DSX_READ_OP_MASK); |
| if (err < 0) |
| return err; |
| |
| st_lsm6dsx_shub_master_enable(sensor, false); |
| |
| config[0] = hub_settings->pause; |
| config[1] = 0; |
| config[2] = slv_config; |
| return st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| } |
| |
| /* |
| * st_lsm6dsx_shub_write - write data to slave device register |
| * |
| * Write data from slave device register. SLV0 is used for |
| * one-shot write operation |
| */ |
| static int |
| st_lsm6dsx_shub_write(struct st_lsm6dsx_sensor *sensor, u8 addr, |
| u8 *data, int len) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| struct st_lsm6dsx_hw *hw = sensor->hw; |
| u8 config[2], slv_addr; |
| int err, i; |
| |
| hub_settings = &hw->settings->shub_settings; |
| if (hub_settings->wr_once.addr) { |
| unsigned int data; |
| |
| data = ST_LSM6DSX_SHIFT_VAL(1, hub_settings->wr_once.mask); |
| err = st_lsm6dsx_shub_write_reg_with_mask(hw, |
| hub_settings->wr_once.addr, |
| hub_settings->wr_once.mask, |
| data); |
| if (err < 0) |
| return err; |
| } |
| |
| slv_addr = ST_LSM6DSX_SLV_ADDR(0, hub_settings->slv0_addr); |
| config[0] = sensor->ext_info.addr << 1; |
| for (i = 0 ; i < len; i++) { |
| config[1] = addr + i; |
| |
| err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| if (err < 0) |
| return err; |
| |
| err = st_lsm6dsx_shub_write_reg(hw, hub_settings->dw_slv0_addr, |
| &data[i], 1); |
| if (err < 0) |
| return err; |
| |
| err = st_lsm6dsx_shub_master_enable(sensor, true); |
| if (err < 0) |
| return err; |
| |
| st_lsm6dsx_shub_wait_complete(hw); |
| |
| st_lsm6dsx_shub_master_enable(sensor, false); |
| } |
| |
| config[0] = hub_settings->pause; |
| config[1] = 0; |
| return st_lsm6dsx_shub_write_reg(hw, slv_addr, config, sizeof(config)); |
| } |
| |
| static int |
| st_lsm6dsx_shub_write_with_mask(struct st_lsm6dsx_sensor *sensor, |
| u8 addr, u8 mask, u8 val) |
| { |
| int err; |
| u8 data; |
| |
| err = st_lsm6dsx_shub_read(sensor, addr, &data, sizeof(data)); |
| if (err < 0) |
| return err; |
| |
| data = ((data & ~mask) | (val << __ffs(mask) & mask)); |
| |
| return st_lsm6dsx_shub_write(sensor, addr, &data, sizeof(data)); |
| } |
| |
| static int |
| st_lsm6dsx_shub_get_odr_val(struct st_lsm6dsx_sensor *sensor, |
| u32 odr, u16 *val) |
| { |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| int i; |
| |
| settings = sensor->ext_info.settings; |
| for (i = 0; i < settings->odr_table.odr_len; i++) { |
| if (settings->odr_table.odr_avl[i].milli_hz == odr) |
| break; |
| } |
| |
| if (i == settings->odr_table.odr_len) |
| return -EINVAL; |
| |
| *val = settings->odr_table.odr_avl[i].val; |
| return 0; |
| } |
| |
| static int |
| st_lsm6dsx_shub_set_odr(struct st_lsm6dsx_sensor *sensor, u32 odr) |
| { |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| u16 val; |
| int err; |
| |
| err = st_lsm6dsx_shub_get_odr_val(sensor, odr, &val); |
| if (err < 0) |
| return err; |
| |
| settings = sensor->ext_info.settings; |
| return st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->odr_table.reg.addr, |
| settings->odr_table.reg.mask, |
| val); |
| } |
| |
| /* use SLV{1,2,3} for FIFO read operations */ |
| static int |
| st_lsm6dsx_shub_config_channels(struct st_lsm6dsx_sensor *sensor, |
| bool enable) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| u8 config[9] = {}, enable_mask, slv_addr; |
| struct st_lsm6dsx_hw *hw = sensor->hw; |
| struct st_lsm6dsx_sensor *cur_sensor; |
| int i, j = 0; |
| |
| hub_settings = &hw->settings->shub_settings; |
| if (enable) |
| enable_mask = hw->enable_mask | BIT(sensor->id); |
| else |
| enable_mask = hw->enable_mask & ~BIT(sensor->id); |
| |
| for (i = ST_LSM6DSX_ID_EXT0; i <= ST_LSM6DSX_ID_EXT2; i++) { |
| if (!hw->iio_devs[i]) |
| continue; |
| |
| cur_sensor = iio_priv(hw->iio_devs[i]); |
| if (!(enable_mask & BIT(cur_sensor->id))) |
| continue; |
| |
| settings = cur_sensor->ext_info.settings; |
| config[j] = (sensor->ext_info.addr << 1) | 1; |
| config[j + 1] = settings->out.addr; |
| config[j + 2] = (settings->out.len & ST_LS6DSX_READ_OP_MASK) | |
| hub_settings->batch_en; |
| j += 3; |
| } |
| |
| slv_addr = ST_LSM6DSX_SLV_ADDR(1, hub_settings->slv0_addr); |
| return st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| } |
| |
| int st_lsm6dsx_shub_set_enable(struct st_lsm6dsx_sensor *sensor, bool enable) |
| { |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| int err; |
| |
| err = st_lsm6dsx_shub_config_channels(sensor, enable); |
| if (err < 0) |
| return err; |
| |
| settings = sensor->ext_info.settings; |
| if (enable) { |
| err = st_lsm6dsx_shub_set_odr(sensor, |
| sensor->ext_info.slv_odr); |
| if (err < 0) |
| return err; |
| } else { |
| err = st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->odr_table.reg.addr, |
| settings->odr_table.reg.mask, 0); |
| if (err < 0) |
| return err; |
| } |
| |
| if (settings->pwr_table.reg.addr) { |
| u8 val; |
| |
| val = enable ? settings->pwr_table.on_val |
| : settings->pwr_table.off_val; |
| err = st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->pwr_table.reg.addr, |
| settings->pwr_table.reg.mask, val); |
| if (err < 0) |
| return err; |
| } |
| |
| return st_lsm6dsx_shub_master_enable(sensor, enable); |
| } |
| |
| static int |
| st_lsm6dsx_shub_read_oneshot(struct st_lsm6dsx_sensor *sensor, |
| struct iio_chan_spec const *ch, |
| int *val) |
| { |
| int err, delay, len; |
| u8 data[4]; |
| |
| err = st_lsm6dsx_shub_set_enable(sensor, true); |
| if (err < 0) |
| return err; |
| |
| delay = 1000000000 / sensor->ext_info.slv_odr; |
| usleep_range(delay, 2 * delay); |
| |
| len = min_t(int, sizeof(data), ch->scan_type.realbits >> 3); |
| err = st_lsm6dsx_shub_read(sensor, ch->address, data, len); |
| if (err < 0) |
| return err; |
| |
| err = st_lsm6dsx_shub_set_enable(sensor, false); |
| if (err < 0) |
| return err; |
| |
| switch (len) { |
| case 2: |
| *val = (s16)le16_to_cpu(*((__le16 *)data)); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return IIO_VAL_INT; |
| } |
| |
| static int |
| st_lsm6dsx_shub_read_raw(struct iio_dev *iio_dev, |
| struct iio_chan_spec const *ch, |
| int *val, int *val2, long mask) |
| { |
| struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); |
| int ret; |
| |
| switch (mask) { |
| case IIO_CHAN_INFO_RAW: |
| ret = iio_device_claim_direct_mode(iio_dev); |
| if (ret) |
| break; |
| |
| ret = st_lsm6dsx_shub_read_oneshot(sensor, ch, val); |
| iio_device_release_direct_mode(iio_dev); |
| break; |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| *val = sensor->ext_info.slv_odr / 1000; |
| *val2 = (sensor->ext_info.slv_odr % 1000) * 1000; |
| ret = IIO_VAL_INT_PLUS_MICRO; |
| break; |
| case IIO_CHAN_INFO_SCALE: |
| *val = 0; |
| *val2 = sensor->gain; |
| ret = IIO_VAL_INT_PLUS_MICRO; |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static int |
| st_lsm6dsx_shub_set_full_scale(struct st_lsm6dsx_sensor *sensor, |
| u32 gain) |
| { |
| const struct st_lsm6dsx_fs_table_entry *fs_table; |
| int i, err; |
| |
| fs_table = &sensor->ext_info.settings->fs_table; |
| if (!fs_table->reg.addr) |
| return -ENOTSUPP; |
| |
| for (i = 0; i < fs_table->fs_len; i++) { |
| if (fs_table->fs_avl[i].gain == gain) |
| break; |
| } |
| |
| if (i == fs_table->fs_len) |
| return -EINVAL; |
| |
| err = st_lsm6dsx_shub_write_with_mask(sensor, fs_table->reg.addr, |
| fs_table->reg.mask, |
| fs_table->fs_avl[i].val); |
| if (err < 0) |
| return err; |
| |
| sensor->gain = gain; |
| |
| return 0; |
| } |
| |
| static int |
| st_lsm6dsx_shub_write_raw(struct iio_dev *iio_dev, |
| struct iio_chan_spec const *chan, |
| int val, int val2, long mask) |
| { |
| struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev); |
| int err; |
| |
| err = iio_device_claim_direct_mode(iio_dev); |
| if (err) |
| return err; |
| |
| switch (mask) { |
| case IIO_CHAN_INFO_SAMP_FREQ: { |
| u16 data; |
| |
| val = val * 1000 + val2 / 1000; |
| err = st_lsm6dsx_shub_get_odr_val(sensor, val, &data); |
| if (!err) { |
| struct st_lsm6dsx_hw *hw = sensor->hw; |
| struct st_lsm6dsx_sensor *ref_sensor; |
| u8 odr_val; |
| int odr; |
| |
| ref_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); |
| odr = st_lsm6dsx_check_odr(ref_sensor, val, &odr_val); |
| if (odr < 0) { |
| err = odr; |
| goto release; |
| } |
| |
| sensor->ext_info.slv_odr = val; |
| sensor->odr = odr; |
| } |
| break; |
| } |
| case IIO_CHAN_INFO_SCALE: |
| err = st_lsm6dsx_shub_set_full_scale(sensor, val2); |
| break; |
| default: |
| err = -EINVAL; |
| break; |
| } |
| |
| release: |
| iio_device_release_direct_mode(iio_dev); |
| |
| return err; |
| } |
| |
| static ssize_t |
| st_lsm6dsx_shub_sampling_freq_avail(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| struct st_lsm6dsx_sensor *sensor = iio_priv(dev_get_drvdata(dev)); |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| int i, len = 0; |
| |
| settings = sensor->ext_info.settings; |
| for (i = 0; i < settings->odr_table.odr_len; i++) { |
| u32 val = settings->odr_table.odr_avl[i].milli_hz; |
| |
| len += scnprintf(buf + len, PAGE_SIZE - len, "%d.%03d ", |
| val / 1000, val % 1000); |
| } |
| buf[len - 1] = '\n'; |
| |
| return len; |
| } |
| |
| static ssize_t st_lsm6dsx_shub_scale_avail(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| struct st_lsm6dsx_sensor *sensor = iio_priv(dev_get_drvdata(dev)); |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| int i, len = 0; |
| |
| settings = sensor->ext_info.settings; |
| for (i = 0; i < settings->fs_table.fs_len; i++) |
| len += scnprintf(buf + len, PAGE_SIZE - len, "0.%06u ", |
| settings->fs_table.fs_avl[i].gain); |
| buf[len - 1] = '\n'; |
| |
| return len; |
| } |
| |
| static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(st_lsm6dsx_shub_sampling_freq_avail); |
| static IIO_DEVICE_ATTR(in_scale_available, 0444, |
| st_lsm6dsx_shub_scale_avail, NULL, 0); |
| static struct attribute *st_lsm6dsx_ext_attributes[] = { |
| &iio_dev_attr_sampling_frequency_available.dev_attr.attr, |
| &iio_dev_attr_in_scale_available.dev_attr.attr, |
| NULL, |
| }; |
| |
| static const struct attribute_group st_lsm6dsx_ext_attribute_group = { |
| .attrs = st_lsm6dsx_ext_attributes, |
| }; |
| |
| static const struct iio_info st_lsm6dsx_ext_info = { |
| .attrs = &st_lsm6dsx_ext_attribute_group, |
| .read_raw = st_lsm6dsx_shub_read_raw, |
| .write_raw = st_lsm6dsx_shub_write_raw, |
| .hwfifo_set_watermark = st_lsm6dsx_set_watermark, |
| }; |
| |
| static struct iio_dev * |
| st_lsm6dsx_shub_alloc_iiodev(struct st_lsm6dsx_hw *hw, |
| enum st_lsm6dsx_sensor_id id, |
| const struct st_lsm6dsx_ext_dev_settings *info, |
| u8 i2c_addr, const char *name) |
| { |
| enum st_lsm6dsx_sensor_id ref_id = ST_LSM6DSX_ID_ACC; |
| struct iio_chan_spec *ext_channels; |
| struct st_lsm6dsx_sensor *sensor; |
| struct iio_dev *iio_dev; |
| |
| iio_dev = devm_iio_device_alloc(hw->dev, sizeof(*sensor)); |
| if (!iio_dev) |
| return NULL; |
| |
| iio_dev->modes = INDIO_DIRECT_MODE; |
| iio_dev->info = &st_lsm6dsx_ext_info; |
| |
| sensor = iio_priv(iio_dev); |
| sensor->id = id; |
| sensor->hw = hw; |
| sensor->odr = hw->settings->odr_table[ref_id].odr_avl[0].milli_hz; |
| sensor->ext_info.slv_odr = info->odr_table.odr_avl[0].milli_hz; |
| sensor->gain = info->fs_table.fs_avl[0].gain; |
| sensor->ext_info.settings = info; |
| sensor->ext_info.addr = i2c_addr; |
| sensor->watermark = 1; |
| |
| switch (info->id) { |
| case ST_LSM6DSX_ID_MAGN: { |
| const struct iio_chan_spec magn_channels[] = { |
| ST_LSM6DSX_CHANNEL(IIO_MAGN, info->out.addr, |
| IIO_MOD_X, 0), |
| ST_LSM6DSX_CHANNEL(IIO_MAGN, info->out.addr + 2, |
| IIO_MOD_Y, 1), |
| ST_LSM6DSX_CHANNEL(IIO_MAGN, info->out.addr + 4, |
| IIO_MOD_Z, 2), |
| IIO_CHAN_SOFT_TIMESTAMP(3), |
| }; |
| |
| ext_channels = devm_kzalloc(hw->dev, sizeof(magn_channels), |
| GFP_KERNEL); |
| if (!ext_channels) |
| return NULL; |
| |
| memcpy(ext_channels, magn_channels, sizeof(magn_channels)); |
| iio_dev->available_scan_masks = st_lsm6dsx_available_scan_masks; |
| iio_dev->channels = ext_channels; |
| iio_dev->num_channels = ARRAY_SIZE(magn_channels); |
| |
| scnprintf(sensor->name, sizeof(sensor->name), "%s_magn", |
| name); |
| break; |
| } |
| default: |
| return NULL; |
| } |
| iio_dev->name = sensor->name; |
| |
| return iio_dev; |
| } |
| |
| static int st_lsm6dsx_shub_init_device(struct st_lsm6dsx_sensor *sensor) |
| { |
| const struct st_lsm6dsx_ext_dev_settings *settings; |
| int err; |
| |
| settings = sensor->ext_info.settings; |
| if (settings->bdu.addr) { |
| err = st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->bdu.addr, |
| settings->bdu.mask, 1); |
| if (err < 0) |
| return err; |
| } |
| |
| if (settings->temp_comp.addr) { |
| err = st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->temp_comp.addr, |
| settings->temp_comp.mask, 1); |
| if (err < 0) |
| return err; |
| } |
| |
| if (settings->off_canc.addr) { |
| err = st_lsm6dsx_shub_write_with_mask(sensor, |
| settings->off_canc.addr, |
| settings->off_canc.mask, 1); |
| if (err < 0) |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| st_lsm6dsx_shub_check_wai(struct st_lsm6dsx_hw *hw, u8 *i2c_addr, |
| const struct st_lsm6dsx_ext_dev_settings *settings) |
| { |
| const struct st_lsm6dsx_shub_settings *hub_settings; |
| u8 config[3], data, slv_addr, slv_config = 0; |
| const struct st_lsm6dsx_reg *aux_sens; |
| struct st_lsm6dsx_sensor *sensor; |
| bool found = false; |
| int i, err; |
| |
| sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]); |
| hub_settings = &hw->settings->shub_settings; |
| aux_sens = &hw->settings->shub_settings.aux_sens; |
| slv_addr = ST_LSM6DSX_SLV_ADDR(0, hub_settings->slv0_addr); |
| /* do not overwrite aux_sens */ |
| if (slv_addr + 2 == aux_sens->addr) |
| slv_config = ST_LSM6DSX_SHIFT_VAL(3, aux_sens->mask); |
| |
| for (i = 0; i < ARRAY_SIZE(settings->i2c_addr); i++) { |
| if (!settings->i2c_addr[i]) |
| continue; |
| |
| /* read wai slave register */ |
| config[0] = (settings->i2c_addr[i] << 1) | 0x1; |
| config[1] = settings->wai.addr; |
| config[2] = 0x1 | slv_config; |
| |
| err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| if (err < 0) |
| return err; |
| |
| err = st_lsm6dsx_shub_master_enable(sensor, true); |
| if (err < 0) |
| return err; |
| |
| st_lsm6dsx_shub_wait_complete(hw); |
| |
| err = st_lsm6dsx_shub_read_output(hw, &data, sizeof(data)); |
| |
| st_lsm6dsx_shub_master_enable(sensor, false); |
| |
| if (err < 0) |
| return err; |
| |
| if (data != settings->wai.val) |
| continue; |
| |
| *i2c_addr = settings->i2c_addr[i]; |
| found = true; |
| break; |
| } |
| |
| /* reset SLV0 channel */ |
| config[0] = hub_settings->pause; |
| config[1] = 0; |
| config[2] = slv_config; |
| err = st_lsm6dsx_shub_write_reg(hw, slv_addr, config, |
| sizeof(config)); |
| if (err < 0) |
| return err; |
| |
| return found ? 0 : -ENODEV; |
| } |
| |
| int st_lsm6dsx_shub_probe(struct st_lsm6dsx_hw *hw, const char *name) |
| { |
| enum st_lsm6dsx_sensor_id id = ST_LSM6DSX_ID_EXT0; |
| struct st_lsm6dsx_sensor *sensor; |
| int err, i, num_ext_dev = 0; |
| u8 i2c_addr = 0; |
| |
| for (i = 0; i < ARRAY_SIZE(st_lsm6dsx_ext_dev_table); i++) { |
| err = st_lsm6dsx_shub_check_wai(hw, &i2c_addr, |
| &st_lsm6dsx_ext_dev_table[i]); |
| if (err == -ENODEV) |
| continue; |
| else if (err < 0) |
| return err; |
| |
| hw->iio_devs[id] = st_lsm6dsx_shub_alloc_iiodev(hw, id, |
| &st_lsm6dsx_ext_dev_table[i], |
| i2c_addr, name); |
| if (!hw->iio_devs[id]) |
| return -ENOMEM; |
| |
| sensor = iio_priv(hw->iio_devs[id]); |
| err = st_lsm6dsx_shub_init_device(sensor); |
| if (err < 0) |
| return err; |
| |
| if (++num_ext_dev >= hw->settings->shub_settings.num_ext_dev) |
| break; |
| id++; |
| } |
| |
| return 0; |
| } |