| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright Altera Corporation (C) 2014. All rights reserved. |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/reset/altr,rst-mgr-a10.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "altr,socfpga-a10-smp"; |
| |
| cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <0>; |
| next-level-cache = <&L2>; |
| }; |
| cpu@1 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <1>; |
| next-level-cache = <&L2>; |
| }; |
| }; |
| |
| intc: intc@ffffd000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0xffffd000 0x1000>, |
| <0xffffc100 0x100>; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| device_type = "soc"; |
| interrupt-parent = <&intc>; |
| ranges; |
| |
| amba { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pdma: pdma@ffda1000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0xffda1000 0x1000>; |
| interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>, |
| <0 84 IRQ_TYPE_LEVEL_HIGH>, |
| <0 85 IRQ_TYPE_LEVEL_HIGH>, |
| <0 86 IRQ_TYPE_LEVEL_HIGH>, |
| <0 87 IRQ_TYPE_LEVEL_HIGH>, |
| <0 88 IRQ_TYPE_LEVEL_HIGH>, |
| <0 89 IRQ_TYPE_LEVEL_HIGH>, |
| <0 90 IRQ_TYPE_LEVEL_HIGH>, |
| <0 91 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| #dma-channels = <8>; |
| #dma-requests = <32>; |
| clocks = <&l4_main_clk>; |
| clock-names = "apb_pclk"; |
| resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>; |
| reset-names = "dma", "dma-ocp"; |
| }; |
| }; |
| |
| base_fpga_region { |
| #address-cells = <0x1>; |
| #size-cells = <0x1>; |
| |
| compatible = "fpga-region"; |
| fpga-mgr = <&fpga_mgr>; |
| }; |
| |
| clkmgr@ffd04000 { |
| compatible = "altr,clk-mgr"; |
| reg = <0xffd04000 0x1000>; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cb_intosc_hs_div2_clk: cb_intosc_hs_div2_clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| cb_intosc_ls_clk: cb_intosc_ls_clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| f2s_free_clk: f2s_free_clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| osc1: osc1 { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| main_pll: main_pll@40 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-pll-clock"; |
| clocks = <&osc1>, <&cb_intosc_ls_clk>, |
| <&f2s_free_clk>; |
| reg = <0x40>; |
| |
| main_mpu_base_clk: main_mpu_base_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| div-reg = <0x140 0 11>; |
| }; |
| |
| main_noc_base_clk: main_noc_base_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| div-reg = <0x144 0 11>; |
| }; |
| |
| main_emaca_clk: main_emaca_clk@68 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x68>; |
| }; |
| |
| main_emacb_clk: main_emacb_clk@6c { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x6C>; |
| }; |
| |
| main_emac_ptp_clk: main_emac_ptp_clk@70 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x70>; |
| }; |
| |
| main_gpio_db_clk: main_gpio_db_clk@74 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x74>; |
| }; |
| |
| main_sdmmc_clk: main_sdmmc_clk@78 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk" |
| ; |
| clocks = <&main_pll>; |
| reg = <0x78>; |
| }; |
| |
| main_s2f_usr0_clk: main_s2f_usr0_clk@7c { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x7C>; |
| }; |
| |
| main_s2f_usr1_clk: main_s2f_usr1_clk@80 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x80>; |
| }; |
| |
| main_hmc_pll_ref_clk: main_hmc_pll_ref_clk@84 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x84>; |
| }; |
| |
| main_periph_ref_clk: main_periph_ref_clk@9c { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_pll>; |
| reg = <0x9C>; |
| }; |
| }; |
| |
| periph_pll: periph_pll@c0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-pll-clock"; |
| clocks = <&osc1>, <&cb_intosc_ls_clk>, |
| <&f2s_free_clk>, <&main_periph_ref_clk>; |
| reg = <0xC0>; |
| |
| peri_mpu_base_clk: peri_mpu_base_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| div-reg = <0x140 16 11>; |
| }; |
| |
| peri_noc_base_clk: peri_noc_base_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| div-reg = <0x144 16 11>; |
| }; |
| |
| peri_emaca_clk: peri_emaca_clk@e8 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xE8>; |
| }; |
| |
| peri_emacb_clk: peri_emacb_clk@ec { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xEC>; |
| }; |
| |
| peri_emac_ptp_clk: peri_emac_ptp_clk@f0 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xF0>; |
| }; |
| |
| peri_gpio_db_clk: peri_gpio_db_clk@f4 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xF4>; |
| }; |
| |
| peri_sdmmc_clk: peri_sdmmc_clk@f8 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xF8>; |
| }; |
| |
| peri_s2f_usr0_clk: peri_s2f_usr0_clk@fc { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0xFC>; |
| }; |
| |
| peri_s2f_usr1_clk: peri_s2f_usr1_clk@100 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0x100>; |
| }; |
| |
| peri_hmc_pll_ref_clk: peri_hmc_pll_ref_clk@104 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&periph_pll>; |
| reg = <0x104>; |
| }; |
| }; |
| |
| mpu_free_clk: mpu_free_clk@60 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_mpu_base_clk>, <&peri_mpu_base_clk>, |
| <&osc1>, <&cb_intosc_hs_div2_clk>, |
| <&f2s_free_clk>; |
| reg = <0x60>; |
| }; |
| |
| noc_free_clk: noc_free_clk@64 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_noc_base_clk>, <&peri_noc_base_clk>, |
| <&osc1>, <&cb_intosc_hs_div2_clk>, |
| <&f2s_free_clk>; |
| reg = <0x64>; |
| }; |
| |
| s2f_user1_free_clk: s2f_user1_free_clk@104 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_s2f_usr1_clk>, <&peri_s2f_usr1_clk>, |
| <&osc1>, <&cb_intosc_hs_div2_clk>, |
| <&f2s_free_clk>; |
| reg = <0x104>; |
| }; |
| |
| sdmmc_free_clk: sdmmc_free_clk@f8 { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&main_sdmmc_clk>, <&peri_sdmmc_clk>, |
| <&osc1>, <&cb_intosc_hs_div2_clk>, |
| <&f2s_free_clk>; |
| fixed-divider = <4>; |
| reg = <0xF8>; |
| }; |
| |
| l4_sys_free_clk: l4_sys_free_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-perip-clk"; |
| clocks = <&noc_free_clk>; |
| fixed-divider = <4>; |
| }; |
| |
| l4_main_clk: l4_main_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&noc_free_clk>; |
| div-reg = <0xA8 0 2>; |
| clk-gate = <0x48 1>; |
| }; |
| |
| l4_mp_clk: l4_mp_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&noc_free_clk>; |
| div-reg = <0xA8 8 2>; |
| clk-gate = <0x48 2>; |
| }; |
| |
| l4_sp_clk: l4_sp_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&noc_free_clk>; |
| div-reg = <0xA8 16 2>; |
| clk-gate = <0x48 3>; |
| }; |
| |
| mpu_periph_clk: mpu_periph_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&mpu_free_clk>; |
| fixed-divider = <4>; |
| clk-gate = <0x48 0>; |
| }; |
| |
| sdmmc_clk: sdmmc_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&sdmmc_free_clk>; |
| clk-gate = <0xC8 5>; |
| clk-phase = <0 135>; |
| }; |
| |
| qspi_clk: qspi_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&l4_main_clk>; |
| clk-gate = <0xC8 11>; |
| }; |
| |
| nand_x_clk: nand_x_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&l4_mp_clk>; |
| clk-gate = <0xC8 10>; |
| }; |
| |
| nand_ecc_clk: nand_ecc_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&nand_x_clk>; |
| clk-gate = <0xC8 10>; |
| }; |
| |
| nand_clk: nand_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&nand_x_clk>; |
| fixed-divider = <4>; |
| clk-gate = <0xC8 10>; |
| }; |
| |
| spi_m_clk: spi_m_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&l4_main_clk>; |
| clk-gate = <0xC8 9>; |
| }; |
| |
| usb_clk: usb_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&l4_mp_clk>; |
| clk-gate = <0xC8 8>; |
| }; |
| |
| s2f_usr1_clk: s2f_usr1_clk { |
| #clock-cells = <0>; |
| compatible = "altr,socfpga-a10-gate-clk"; |
| clocks = <&peri_s2f_usr1_clk>; |
| clk-gate = <0xC8 6>; |
| }; |
| }; |
| }; |
| |
| socfpga_axi_setup: stmmac-axi-config { |
| snps,wr_osr_lmt = <0xf>; |
| snps,rd_osr_lmt = <0xf>; |
| snps,blen = <0 0 0 0 16 0 0>; |
| }; |
| |
| gmac0: ethernet@ff800000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; |
| altr,sysmgr-syscon = <&sysmgr 0x44 0>; |
| reg = <0xff800000 0x2000>; |
| interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| /* Filled in by bootloader */ |
| mac-address = [00 00 00 00 00 00]; |
| snps,multicast-filter-bins = <256>; |
| snps,perfect-filter-entries = <128>; |
| tx-fifo-depth = <4096>; |
| rx-fifo-depth = <16384>; |
| clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| resets = <&rst EMAC0_RESET>, <&rst EMAC0_OCP_RESET>; |
| reset-names = "stmmaceth", "stmmaceth-ocp"; |
| snps,axi-config = <&socfpga_axi_setup>; |
| status = "disabled"; |
| }; |
| |
| gmac1: ethernet@ff802000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; |
| altr,sysmgr-syscon = <&sysmgr 0x48 8>; |
| reg = <0xff802000 0x2000>; |
| interrupts = <0 93 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| /* Filled in by bootloader */ |
| mac-address = [00 00 00 00 00 00]; |
| snps,multicast-filter-bins = <256>; |
| snps,perfect-filter-entries = <128>; |
| tx-fifo-depth = <4096>; |
| rx-fifo-depth = <16384>; |
| clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| resets = <&rst EMAC1_RESET>, <&rst EMAC1_OCP_RESET>; |
| reset-names = "stmmaceth", "stmmaceth-ocp"; |
| snps,axi-config = <&socfpga_axi_setup>; |
| status = "disabled"; |
| }; |
| |
| gmac2: ethernet@ff804000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; |
| altr,sysmgr-syscon = <&sysmgr 0x4C 16>; |
| reg = <0xff804000 0x2000>; |
| interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| /* Filled in by bootloader */ |
| mac-address = [00 00 00 00 00 00]; |
| snps,multicast-filter-bins = <256>; |
| snps,perfect-filter-entries = <128>; |
| tx-fifo-depth = <4096>; |
| rx-fifo-depth = <16384>; |
| clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| resets = <&rst EMAC2_RESET>, <&rst EMAC2_OCP_RESET>; |
| reset-names = "stmmaceth", "stmmaceth-ocp"; |
| snps,axi-config = <&socfpga_axi_setup>; |
| status = "disabled"; |
| }; |
| |
| gpio0: gpio@ffc02900 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dw-apb-gpio"; |
| reg = <0xffc02900 0x100>; |
| resets = <&rst GPIO0_RESET>; |
| status = "disabled"; |
| |
| porta: gpio-controller@0 { |
| compatible = "snps,dw-apb-gpio-port"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| snps,nr-gpios = <29>; |
| reg = <0>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 112 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| gpio1: gpio@ffc02a00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dw-apb-gpio"; |
| reg = <0xffc02a00 0x100>; |
| resets = <&rst GPIO1_RESET>; |
| status = "disabled"; |
| |
| portb: gpio-controller@0 { |
| compatible = "snps,dw-apb-gpio-port"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| snps,nr-gpios = <29>; |
| reg = <0>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| gpio2: gpio@ffc02b00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dw-apb-gpio"; |
| reg = <0xffc02b00 0x100>; |
| resets = <&rst GPIO2_RESET>; |
| status = "disabled"; |
| |
| portc: gpio-controller@0 { |
| compatible = "snps,dw-apb-gpio-port"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| snps,nr-gpios = <27>; |
| reg = <0>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| fpga_mgr: fpga-mgr@ffd03000 { |
| compatible = "altr,socfpga-a10-fpga-mgr"; |
| reg = <0xffd03000 0x100 |
| 0xffcfe400 0x20>; |
| clocks = <&l4_mp_clk>; |
| resets = <&rst FPGAMGR_RESET>; |
| reset-names = "fpgamgr"; |
| }; |
| |
| i2c0: i2c@ffc02200 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02200 0x100>; |
| interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst I2C0_RESET>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@ffc02300 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02300 0x100>; |
| interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst I2C1_RESET>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@ffc02400 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02400 0x100>; |
| interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst I2C2_RESET>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@ffc02500 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02500 0x100>; |
| interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst I2C3_RESET>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@ffc02600 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02600 0x100>; |
| interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst I2C4_RESET>; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@ffda4000 { |
| compatible = "snps,dw-apb-ssi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xffda4000 0x100>; |
| interrupts = <0 101 4>; |
| num-cs = <4>; |
| /*32bit_access;*/ |
| clocks = <&spi_m_clk>; |
| resets = <&rst SPIM0_RESET>; |
| reset-names = "spi"; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@ffda5000 { |
| compatible = "snps,dw-apb-ssi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xffda5000 0x100>; |
| interrupts = <0 102 4>; |
| num-cs = <4>; |
| /*32bit_access;*/ |
| tx-dma-channel = <&pdma 16>; |
| rx-dma-channel = <&pdma 17>; |
| clocks = <&spi_m_clk>; |
| resets = <&rst SPIM1_RESET>; |
| reset-names = "spi"; |
| status = "disabled"; |
| }; |
| |
| sdr: sdr@ffcfb100 { |
| compatible = "altr,sdr-ctl", "syscon"; |
| reg = <0xffcfb100 0x80>; |
| }; |
| |
| L2: cache-controller@fffff000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0xfffff000 0x1000>; |
| interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-level = <2>; |
| prefetch-data = <1>; |
| prefetch-instr = <1>; |
| arm,shared-override; |
| }; |
| |
| mmc: dwmmc0@ff808000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "altr,socfpga-dw-mshc"; |
| reg = <0xff808000 0x1000>; |
| interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; |
| fifo-depth = <0x400>; |
| clocks = <&l4_mp_clk>, <&sdmmc_clk>; |
| clock-names = "biu", "ciu"; |
| resets = <&rst SDMMC_RESET>; |
| status = "disabled"; |
| }; |
| |
| nand: nand@ffb90000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "altr,socfpga-denali-nand"; |
| reg = <0xffb90000 0x72000>, |
| <0xffb80000 0x10000>; |
| reg-names = "nand_data", "denali_reg"; |
| interrupts = <0 99 4>; |
| clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; |
| clock-names = "nand", "nand_x", "ecc"; |
| resets = <&rst NAND_RESET>; |
| status = "disabled"; |
| }; |
| |
| ocram: sram@ffe00000 { |
| compatible = "mmio-sram"; |
| reg = <0xffe00000 0x40000>; |
| }; |
| |
| eccmgr: eccmgr { |
| compatible = "altr,socfpga-a10-ecc-manager"; |
| altr,sysmgr-syscon = <&sysmgr>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ranges; |
| |
| sdramedac { |
| compatible = "altr,sdram-edac-a10"; |
| altr,sdr-syscon = <&sdr>; |
| interrupts = <17 IRQ_TYPE_LEVEL_HIGH>, |
| <49 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| l2-ecc@ffd06010 { |
| compatible = "altr,socfpga-a10-l2-ecc"; |
| reg = <0xffd06010 0x4>; |
| interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, |
| <32 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| ocram-ecc@ff8c3000 { |
| compatible = "altr,socfpga-a10-ocram-ecc"; |
| reg = <0xff8c3000 0x400>; |
| interrupts = <1 IRQ_TYPE_LEVEL_HIGH>, |
| <33 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| emac0-rx-ecc@ff8c0800 { |
| compatible = "altr,socfpga-eth-mac-ecc"; |
| reg = <0xff8c0800 0x400>; |
| altr,ecc-parent = <&gmac0>; |
| interrupts = <4 IRQ_TYPE_LEVEL_HIGH>, |
| <36 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| emac0-tx-ecc@ff8c0c00 { |
| compatible = "altr,socfpga-eth-mac-ecc"; |
| reg = <0xff8c0c00 0x400>; |
| altr,ecc-parent = <&gmac0>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH>, |
| <37 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| dma-ecc@ff8c8000 { |
| compatible = "altr,socfpga-dma-ecc"; |
| reg = <0xff8c8000 0x400>; |
| altr,ecc-parent = <&pdma>; |
| interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, |
| <42 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| usb0-ecc@ff8c8800 { |
| compatible = "altr,socfpga-usb-ecc"; |
| reg = <0xff8c8800 0x400>; |
| altr,ecc-parent = <&usb0>; |
| interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, |
| <34 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| qspi: spi@ff809000 { |
| compatible = "cdns,qspi-nor"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xff809000 0x100>, |
| <0xffa00000 0x100000>; |
| interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; |
| cdns,fifo-depth = <128>; |
| cdns,fifo-width = <4>; |
| cdns,trigger-address = <0x00000000>; |
| clocks = <&qspi_clk>; |
| resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; |
| reset-names = "qspi", "qspi-ocp"; |
| status = "disabled"; |
| }; |
| |
| rst: rstmgr@ffd05000 { |
| #reset-cells = <1>; |
| compatible = "altr,rst-mgr"; |
| reg = <0xffd05000 0x100>; |
| altr,modrst-offset = <0x20>; |
| }; |
| |
| scu: snoop-control-unit@ffffc000 { |
| compatible = "arm,cortex-a9-scu"; |
| reg = <0xffffc000 0x100>; |
| }; |
| |
| sysmgr: sysmgr@ffd06000 { |
| compatible = "altr,sys-mgr", "syscon"; |
| reg = <0xffd06000 0x300>; |
| cpu1-start-addr = <0xffd06230>; |
| }; |
| |
| /* Local timer */ |
| timer@ffffc600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0xffffc600 0x100>; |
| interrupts = <1 13 0xf01>; |
| clocks = <&mpu_periph_clk>; |
| }; |
| |
| timer0: timer0@ffc02700 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 115 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xffc02700 0x100>; |
| clocks = <&l4_sp_clk>; |
| clock-names = "timer"; |
| resets = <&rst SPTIMER0_RESET>; |
| reset-names = "timer"; |
| }; |
| |
| timer1: timer1@ffc02800 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 116 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xffc02800 0x100>; |
| clocks = <&l4_sp_clk>; |
| clock-names = "timer"; |
| resets = <&rst SPTIMER1_RESET>; |
| reset-names = "timer"; |
| }; |
| |
| timer2: timer2@ffd00000 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 117 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xffd00000 0x100>; |
| clocks = <&l4_sys_free_clk>; |
| clock-names = "timer"; |
| resets = <&rst L4SYSTIMER0_RESET>; |
| reset-names = "timer"; |
| }; |
| |
| timer3: timer3@ffd00100 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xffd00100 0x100>; |
| clocks = <&l4_sys_free_clk>; |
| clock-names = "timer"; |
| resets = <&rst L4SYSTIMER1_RESET>; |
| reset-names = "timer"; |
| }; |
| |
| uart0: serial0@ffc02000 { |
| compatible = "snps,dw-apb-uart"; |
| reg = <0xffc02000 0x100>; |
| interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst UART0_RESET>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial1@ffc02100 { |
| compatible = "snps,dw-apb-uart"; |
| reg = <0xffc02100 0x100>; |
| interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clocks = <&l4_sp_clk>; |
| resets = <&rst UART1_RESET>; |
| status = "disabled"; |
| }; |
| |
| usbphy0: usbphy { |
| #phy-cells = <0>; |
| compatible = "usb-nop-xceiv"; |
| status = "okay"; |
| }; |
| |
| usb0: usb@ffb00000 { |
| compatible = "snps,dwc2"; |
| reg = <0xffb00000 0xffff>; |
| interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&usb_clk>; |
| clock-names = "otg"; |
| resets = <&rst USB0_RESET>; |
| reset-names = "dwc2"; |
| phys = <&usbphy0>; |
| phy-names = "usb2-phy"; |
| status = "disabled"; |
| }; |
| |
| usb1: usb@ffb40000 { |
| compatible = "snps,dwc2"; |
| reg = <0xffb40000 0xffff>; |
| interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&usb_clk>; |
| clock-names = "otg"; |
| resets = <&rst USB1_RESET>; |
| reset-names = "dwc2"; |
| phys = <&usbphy0>; |
| phy-names = "usb2-phy"; |
| status = "disabled"; |
| }; |
| |
| watchdog0: watchdog@ffd00200 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00200 0x100>; |
| interrupts = <0 119 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sys_free_clk>; |
| resets = <&rst L4WD0_RESET>; |
| status = "disabled"; |
| }; |
| |
| watchdog1: watchdog@ffd00300 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00300 0x100>; |
| interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l4_sys_free_clk>; |
| resets = <&rst L4WD1_RESET>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
