| # SPDX-License-Identifier: GPL-2.0 |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/mmc/mtk-sd.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: MTK MSDC Storage Host Controller |
| |
| maintainers: |
| - Chaotian Jing <chaotian.jing@mediatek.com> |
| - Wenbin Mei <wenbin.mei@mediatek.com> |
| |
| properties: |
| compatible: |
| oneOf: |
| - enum: |
| - mediatek,mt2701-mmc |
| - mediatek,mt2712-mmc |
| - mediatek,mt6779-mmc |
| - mediatek,mt6795-mmc |
| - mediatek,mt7620-mmc |
| - mediatek,mt7622-mmc |
| - mediatek,mt7986-mmc |
| - mediatek,mt8135-mmc |
| - mediatek,mt8173-mmc |
| - mediatek,mt8183-mmc |
| - mediatek,mt8516-mmc |
| - items: |
| - const: mediatek,mt7623-mmc |
| - const: mediatek,mt2701-mmc |
| - items: |
| - enum: |
| - mediatek,mt8186-mmc |
| - mediatek,mt8188-mmc |
| - mediatek,mt8192-mmc |
| - mediatek,mt8195-mmc |
| - mediatek,mt8365-mmc |
| - const: mediatek,mt8183-mmc |
| |
| reg: |
| minItems: 1 |
| items: |
| - description: base register (required). |
| - description: top base register (required for MT8183). |
| |
| clocks: |
| description: |
| Should contain phandle for the clock feeding the MMC controller. |
| minItems: 2 |
| maxItems: 7 |
| |
| clock-names: |
| minItems: 2 |
| maxItems: 7 |
| |
| interrupts: |
| description: |
| Should at least contain MSDC GIC interrupt. To support SDIO in-band wakeup, an extended |
| interrupt is required and be configured as wakeup source irq. |
| minItems: 1 |
| maxItems: 2 |
| |
| interrupt-names: |
| items: |
| - const: msdc |
| - const: sdio_wakeup |
| |
| pinctrl-names: |
| description: |
| Should at least contain default and state_uhs. To support SDIO in-band wakeup, dat1 pin |
| will be switched between GPIO mode and SDIO DAT1 mode, state_eint is mandatory in this |
| scenario. |
| minItems: 2 |
| items: |
| - const: default |
| - const: state_uhs |
| - const: state_eint |
| |
| pinctrl-0: |
| description: |
| should contain default/high speed pin ctrl. |
| maxItems: 1 |
| |
| pinctrl-1: |
| description: |
| should contain uhs mode pin ctrl. |
| maxItems: 1 |
| |
| pinctrl-2: |
| description: |
| should switch dat1 pin to GPIO mode. |
| maxItems: 1 |
| |
| assigned-clocks: |
| description: |
| PLL of the source clock. |
| maxItems: 1 |
| |
| assigned-clock-parents: |
| description: |
| parent of source clock, used for HS400 mode to get 400Mhz source clock. |
| maxItems: 1 |
| |
| hs400-ds-delay: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| HS400 DS delay setting. |
| minimum: 0 |
| maximum: 0xffffffff |
| |
| mediatek,hs200-cmd-int-delay: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| HS200 command internal delay setting. |
| This field has total 32 stages. |
| The value is an integer from 0 to 31. |
| minimum: 0 |
| maximum: 31 |
| |
| mediatek,hs400-cmd-int-delay: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| HS400 command internal delay setting. |
| This field has total 32 stages. |
| The value is an integer from 0 to 31. |
| minimum: 0 |
| maximum: 31 |
| |
| mediatek,hs400-cmd-resp-sel-rising: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| HS400 command response sample selection. |
| If present, HS400 command responses are sampled on rising edges. |
| If not present, HS400 command responses are sampled on falling edges. |
| |
| mediatek,hs400-ds-dly3: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| Gear of the third delay line for DS for input data latch in data |
| pad macro, there are 32 stages from 0 to 31. |
| For different corner IC, the time is different about one step, it is |
| about 100ps. |
| The value is confirmed by doing scan and calibration to find a best |
| value with corner IC and it is valid only for HS400 mode. |
| minimum: 0 |
| maximum: 31 |
| |
| mediatek,latch-ck: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| Some SoCs do not support enhance_rx, need set correct latch-ck to avoid |
| data crc error caused by stop clock(fifo full) Valid range = [0:0x7]. |
| if not present, default value is 0. |
| applied to compatible "mediatek,mt2701-mmc". |
| minimum: 0 |
| maximum: 7 |
| |
| resets: |
| maxItems: 1 |
| |
| reset-names: |
| const: hrst |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| - clocks |
| - clock-names |
| - pinctrl-names |
| - pinctrl-0 |
| - pinctrl-1 |
| - vmmc-supply |
| - vqmmc-supply |
| |
| allOf: |
| - $ref: mmc-controller.yaml# |
| - if: |
| properties: |
| compatible: |
| enum: |
| - mediatek,mt2701-mmc |
| - mediatek,mt6779-mmc |
| - mediatek,mt6795-mmc |
| - mediatek,mt7620-mmc |
| - mediatek,mt7622-mmc |
| - mediatek,mt7623-mmc |
| - mediatek,mt8135-mmc |
| - mediatek,mt8173-mmc |
| - mediatek,mt8183-mmc |
| - mediatek,mt8186-mmc |
| - mediatek,mt8188-mmc |
| - mediatek,mt8195-mmc |
| - mediatek,mt8516-mmc |
| then: |
| properties: |
| clocks: |
| minItems: 2 |
| items: |
| - description: source clock |
| - description: HCLK which used for host |
| - description: independent source clock gate |
| clock-names: |
| minItems: 2 |
| items: |
| - const: source |
| - const: hclk |
| - const: source_cg |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: mediatek,mt2712-mmc |
| then: |
| properties: |
| clocks: |
| minItems: 3 |
| items: |
| - description: source clock |
| - description: HCLK which used for host |
| - description: independent source clock gate |
| - description: bus clock used for internal register access (required for MSDC0/3). |
| clock-names: |
| minItems: 3 |
| items: |
| - const: source |
| - const: hclk |
| - const: source_cg |
| - const: bus_clk |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: mediatek,mt8183-mmc |
| then: |
| properties: |
| reg: |
| minItems: 2 |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - mediatek,mt7986-mmc |
| then: |
| properties: |
| clocks: |
| minItems: 3 |
| items: |
| - description: source clock |
| - description: HCLK which used for host |
| - description: independent source clock gate |
| - description: bus clock used for internal register access (required for MSDC0/3). |
| - description: msdc subsys clock gate |
| clock-names: |
| minItems: 3 |
| items: |
| - const: source |
| - const: hclk |
| - const: source_cg |
| - const: bus_clk |
| - const: sys_cg |
| |
| - if: |
| properties: |
| compatible: |
| enum: |
| - mediatek,mt8186-mmc |
| - mediatek,mt8188-mmc |
| - mediatek,mt8195-mmc |
| then: |
| properties: |
| clocks: |
| items: |
| - description: source clock |
| - description: HCLK which used for host |
| - description: independent source clock gate |
| - description: crypto clock used for data encrypt/decrypt (optional) |
| clock-names: |
| items: |
| - const: source |
| - const: hclk |
| - const: source_cg |
| - const: crypto |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: mediatek,mt8192-mmc |
| then: |
| properties: |
| clocks: |
| items: |
| - description: source clock |
| - description: HCLK which used for host |
| - description: independent source clock gate |
| - description: msdc subsys clock gate |
| - description: peripheral bus clock gate |
| - description: AXI bus clock gate |
| - description: AHB bus clock gate |
| clock-names: |
| items: |
| - const: source |
| - const: hclk |
| - const: source_cg |
| - const: sys_cg |
| - const: pclk_cg |
| - const: axi_cg |
| - const: ahb_cg |
| |
| unevaluatedProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/mt8173-clk.h> |
| mmc0: mmc@11230000 { |
| compatible = "mediatek,mt8173-mmc"; |
| reg = <0x11230000 0x1000>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; |
| vmmc-supply = <&mt6397_vemc_3v3_reg>; |
| vqmmc-supply = <&mt6397_vio18_reg>; |
| clocks = <&pericfg CLK_PERI_MSDC30_0>, |
| <&topckgen CLK_TOP_MSDC50_0_H_SEL>; |
| clock-names = "source", "hclk"; |
| pinctrl-names = "default", "state_uhs"; |
| pinctrl-0 = <&mmc0_pins_default>; |
| pinctrl-1 = <&mmc0_pins_uhs>; |
| assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; |
| assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; |
| hs400-ds-delay = <0x14015>; |
| mediatek,hs200-cmd-int-delay = <26>; |
| mediatek,hs400-cmd-int-delay = <14>; |
| mediatek,hs400-cmd-resp-sel-rising; |
| }; |
| |
| mmc3: mmc@11260000 { |
| compatible = "mediatek,mt8173-mmc"; |
| reg = <0x11260000 0x1000>; |
| clock-names = "source", "hclk"; |
| clocks = <&pericfg CLK_PERI_MSDC30_3>, |
| <&topckgen CLK_TOP_MSDC50_2_H_SEL>; |
| interrupt-names = "msdc", "sdio_wakeup"; |
| interrupts-extended = <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_LOW 0>, |
| <&pio 23 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default", "state_uhs", "state_eint"; |
| pinctrl-0 = <&mmc2_pins_default>; |
| pinctrl-1 = <&mmc2_pins_uhs>; |
| pinctrl-2 = <&mmc2_pins_eint>; |
| bus-width = <4>; |
| max-frequency = <200000000>; |
| cap-sd-highspeed; |
| sd-uhs-sdr104; |
| keep-power-in-suspend; |
| wakeup-source; |
| cap-sdio-irq; |
| no-mmc; |
| no-sd; |
| non-removable; |
| vmmc-supply = <&sdio_fixed_3v3>; |
| vqmmc-supply = <&mt6397_vgp3_reg>; |
| mmc-pwrseq = <&wifi_pwrseq>; |
| }; |
| |
| ... |
