| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Device Tree Source for common parts of Salvator-X board variants |
| * |
| * Copyright (C) 2015-2016 Renesas Electronics Corp. |
| */ |
| |
| /* |
| * SSI-AK4613 |
| * |
| * This command is required when Playback/Capture |
| * |
| * amixer set "DVC Out" 100% |
| * amixer set "DVC In" 100% |
| * |
| * You can use Mute |
| * |
| * amixer set "DVC Out Mute" on |
| * amixer set "DVC In Mute" on |
| * |
| * You can use Volume Ramp |
| * |
| * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" |
| * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" |
| * amixer set "DVC Out Ramp" on |
| * aplay xxx.wav & |
| * amixer set "DVC Out" 80% // Volume Down |
| * amixer set "DVC Out" 100% // Volume Up |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| aliases { |
| serial0 = &scif2; |
| serial1 = &hscif1; |
| ethernet0 = &avb; |
| mmc0 = &sdhi2; |
| mmc1 = &sdhi0; |
| mmc2 = &sdhi3; |
| }; |
| |
| chosen { |
| bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| audio_clkout: audio-clkout { |
| /* |
| * This is same as <&rcar_sound 0> |
| * but needed to avoid cs2000/rcar_sound probe dead-lock |
| */ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <12288000>; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pwm1 0 50000>; |
| |
| brightness-levels = <256 128 64 16 8 4 0>; |
| default-brightness-level = <6>; |
| |
| power-supply = <®_12v>; |
| enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| cvbs-in { |
| compatible = "composite-video-connector"; |
| label = "CVBS IN"; |
| |
| port { |
| cvbs_con: endpoint { |
| remote-endpoint = <&adv7482_ain7>; |
| }; |
| }; |
| }; |
| |
| hdmi-in { |
| compatible = "hdmi-connector"; |
| label = "HDMI IN"; |
| type = "a"; |
| |
| port { |
| hdmi_in_con: endpoint { |
| remote-endpoint = <&adv7482_hdmi>; |
| }; |
| }; |
| }; |
| |
| hdmi0-out { |
| compatible = "hdmi-connector"; |
| label = "HDMI0 OUT"; |
| type = "a"; |
| |
| port { |
| hdmi0_con: endpoint { |
| }; |
| }; |
| }; |
| |
| hdmi1-out { |
| compatible = "hdmi-connector"; |
| label = "HDMI1 OUT"; |
| type = "a"; |
| |
| port { |
| hdmi1_con: endpoint { |
| }; |
| }; |
| }; |
| |
| keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&keys_pins>; |
| pinctrl-names = "default"; |
| |
| key-1 { |
| gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_1>; |
| label = "SW4-1"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-2 { |
| gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_2>; |
| label = "SW4-2"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-3 { |
| gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_3>; |
| label = "SW4-3"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-4 { |
| gpios = <&gpio5 23 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_4>; |
| label = "SW4-4"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-a { |
| gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_A>; |
| label = "TSW0"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-b { |
| gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_B>; |
| label = "TSW1"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| key-c { |
| gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_C>; |
| label = "TSW2"; |
| wakeup-source; |
| debounce-interval = <20>; |
| }; |
| }; |
| |
| reg_1p8v: regulator0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| reg_3p3v: regulator1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| reg_12v: regulator2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-12V"; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sound_card: sound { |
| compatible = "audio-graph-card"; |
| |
| label = "rcar-sound"; |
| |
| dais = <&rsnd_port0 /* ak4613 */ |
| &rsnd_port1 /* HDMI0 */ |
| #ifdef SOC_HAS_HDMI1 |
| &rsnd_port2 /* HDMI1 */ |
| #endif |
| >; |
| }; |
| |
| vbus0_usb2: regulator-vbus0-usb2 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "USB20_VBUS0"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| |
| gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vcc_sdhi0: regulator-vcc-sdhi0 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "SDHI0 Vcc"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vccq_sdhi0: regulator-vccq-sdhi0 { |
| compatible = "regulator-gpio"; |
| |
| regulator-name = "SDHI0 VccQ"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; |
| gpios-states = <1>; |
| states = <3300000 1>, <1800000 0>; |
| }; |
| |
| vcc_sdhi3: regulator-vcc-sdhi3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "SDHI3 Vcc"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vccq_sdhi3: regulator-vccq-sdhi3 { |
| compatible = "regulator-gpio"; |
| |
| regulator-name = "SDHI3 VccQ"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; |
| gpios-states = <1>; |
| states = <3300000 1>, <1800000 0>; |
| }; |
| |
| vga { |
| compatible = "vga-connector"; |
| |
| port { |
| vga_in: endpoint { |
| remote-endpoint = <&adv7123_out>; |
| }; |
| }; |
| }; |
| |
| vga-encoder { |
| compatible = "adi,adv7123"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| adv7123_in: endpoint { |
| remote-endpoint = <&du_out_rgb>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| adv7123_out: endpoint { |
| remote-endpoint = <&vga_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| x12_clk: x12 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24576000>; |
| }; |
| |
| /* External DU dot clocks */ |
| x21_clk: x21-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <33000000>; |
| }; |
| |
| x22_clk: x22-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <33000000>; |
| }; |
| |
| x23_clk: x23-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <25000000>; |
| }; |
| }; |
| |
| &a57_0 { |
| cpu-supply = <&dvfs>; |
| }; |
| |
| &audio_clk_a { |
| clock-frequency = <22579200>; |
| }; |
| |
| &avb { |
| pinctrl-0 = <&avb_pins>; |
| pinctrl-names = "default"; |
| phy-handle = <&phy0>; |
| tx-internal-delay-ps = <2000>; |
| status = "okay"; |
| |
| phy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-id0022.1622", |
| "ethernet-phy-ieee802.3-c22"; |
| rxc-skew-ps = <1500>; |
| reg = <0>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| &csi20 { |
| status = "okay"; |
| |
| ports { |
| port@0 { |
| csi20_in: endpoint { |
| clock-lanes = <0>; |
| data-lanes = <1>; |
| remote-endpoint = <&adv7482_txb>; |
| }; |
| }; |
| }; |
| }; |
| |
| &csi40 { |
| status = "okay"; |
| |
| ports { |
| port@0 { |
| csi40_in: endpoint { |
| clock-lanes = <0>; |
| data-lanes = <1 2 3 4>; |
| remote-endpoint = <&adv7482_txa>; |
| }; |
| }; |
| }; |
| }; |
| |
| &du { |
| pinctrl-0 = <&du_pins>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| ports { |
| port@0 { |
| endpoint { |
| remote-endpoint = <&adv7123_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &ehci0 { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &ehci1 { |
| status = "okay"; |
| }; |
| |
| &extalr_clk { |
| clock-frequency = <32768>; |
| }; |
| |
| &hdmi0 { |
| status = "okay"; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| rcar_dw_hdmi0_out: endpoint { |
| remote-endpoint = <&hdmi0_con>; |
| }; |
| }; |
| port@2 { |
| reg = <2>; |
| dw_hdmi0_snd_in: endpoint { |
| remote-endpoint = <&rsnd_endpoint1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &hdmi0_con { |
| remote-endpoint = <&rcar_dw_hdmi0_out>; |
| }; |
| |
| #ifdef SOC_HAS_HDMI1 |
| &hdmi1 { |
| status = "okay"; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| rcar_dw_hdmi1_out: endpoint { |
| remote-endpoint = <&hdmi1_con>; |
| }; |
| }; |
| port@2 { |
| reg = <2>; |
| dw_hdmi1_snd_in: endpoint { |
| remote-endpoint = <&rsnd_endpoint2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &hdmi1_con { |
| remote-endpoint = <&rcar_dw_hdmi1_out>; |
| }; |
| #endif /* SOC_HAS_HDMI1 */ |
| |
| &hscif1 { |
| pinctrl-0 = <&hscif1_pins>; |
| pinctrl-names = "default"; |
| |
| uart-has-rtscts; |
| /* Please only enable hscif1 or scif1 */ |
| status = "okay"; |
| }; |
| |
| &hsusb { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| pinctrl-0 = <&i2c2_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| clock-frequency = <100000>; |
| |
| ak4613: codec@10 { |
| compatible = "asahi-kasei,ak4613"; |
| #sound-dai-cells = <0>; |
| reg = <0x10>; |
| clocks = <&rcar_sound 3>; |
| |
| asahi-kasei,in1-single-end; |
| asahi-kasei,in2-single-end; |
| asahi-kasei,out1-single-end; |
| asahi-kasei,out2-single-end; |
| asahi-kasei,out3-single-end; |
| asahi-kasei,out4-single-end; |
| asahi-kasei,out5-single-end; |
| asahi-kasei,out6-single-end; |
| |
| port { |
| ak4613_endpoint: endpoint { |
| remote-endpoint = <&rsnd_endpoint0>; |
| }; |
| }; |
| }; |
| |
| cs2000: clk_multiplier@4f { |
| #clock-cells = <0>; |
| compatible = "cirrus,cs2000-cp"; |
| reg = <0x4f>; |
| clocks = <&audio_clkout>, <&x12_clk>; |
| clock-names = "clk_in", "ref_clk"; |
| |
| assigned-clocks = <&cs2000>; |
| assigned-clock-rates = <24576000>; /* 1/1 divide */ |
| }; |
| }; |
| |
| &i2c4 { |
| status = "okay"; |
| |
| pca9654: gpio@20 { |
| compatible = "onnn,pca9654"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| video-receiver@70 { |
| compatible = "adi,adv7482"; |
| reg = <0x70 0x71 0x72 0x73 0x74 0x75 |
| 0x60 0x61 0x62 0x63 0x64 0x65>; |
| reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", |
| "infoframe", "cbus", "cec", "sdp", "txa", "txb" ; |
| |
| interrupt-parent = <&gpio6>; |
| interrupt-names = "intrq1", "intrq2"; |
| interrupts = <30 IRQ_TYPE_LEVEL_LOW>, |
| <31 IRQ_TYPE_LEVEL_LOW>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@7 { |
| reg = <7>; |
| |
| adv7482_ain7: endpoint { |
| remote-endpoint = <&cvbs_con>; |
| }; |
| }; |
| |
| port@8 { |
| reg = <8>; |
| |
| adv7482_hdmi: endpoint { |
| remote-endpoint = <&hdmi_in_con>; |
| }; |
| }; |
| |
| port@a { |
| reg = <10>; |
| |
| adv7482_txa: endpoint { |
| clock-lanes = <0>; |
| data-lanes = <1 2 3 4>; |
| remote-endpoint = <&csi40_in>; |
| }; |
| }; |
| |
| port@b { |
| reg = <11>; |
| |
| adv7482_txb: endpoint { |
| clock-lanes = <0>; |
| data-lanes = <1>; |
| remote-endpoint = <&csi20_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| csa_vdd: adc@7c { |
| compatible = "maxim,max9611"; |
| reg = <0x7c>; |
| |
| shunt-resistor-micro-ohms = <5000>; |
| }; |
| |
| csa_dvfs: adc@7f { |
| compatible = "maxim,max9611"; |
| reg = <0x7f>; |
| |
| shunt-resistor-micro-ohms = <5000>; |
| }; |
| }; |
| |
| &i2c_dvfs { |
| status = "okay"; |
| |
| clock-frequency = <400000>; |
| |
| pmic: pmic@30 { |
| pinctrl-0 = <&irq0_pins>; |
| pinctrl-names = "default"; |
| |
| compatible = "rohm,bd9571mwv"; |
| reg = <0x30>; |
| interrupt-parent = <&intc_ex>; |
| interrupts = <0 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| rohm,ddr-backup-power = <0xf>; |
| rohm,rstbmode-level; |
| |
| regulators { |
| dvfs: dvfs { |
| regulator-name = "dvfs"; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1030000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| eeprom@50 { |
| compatible = "rohm,br24t01", "atmel,24c01"; |
| reg = <0x50>; |
| pagesize = <8>; |
| }; |
| }; |
| |
| &ohci0 { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &ohci1 { |
| status = "okay"; |
| }; |
| |
| &pcie_bus_clk { |
| clock-frequency = <100000000>; |
| }; |
| |
| &pciec0 { |
| status = "okay"; |
| }; |
| |
| &pciec1 { |
| status = "okay"; |
| }; |
| |
| &pfc { |
| pinctrl-0 = <&scif_clk_pins>; |
| pinctrl-names = "default"; |
| |
| avb_pins: avb { |
| mux { |
| groups = "avb_link", "avb_mdio", "avb_mii"; |
| function = "avb"; |
| }; |
| |
| pins_mdio { |
| groups = "avb_mdio"; |
| drive-strength = <24>; |
| }; |
| |
| pins_mii_tx { |
| pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0", |
| "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3"; |
| drive-strength = <12>; |
| }; |
| }; |
| |
| du_pins: du { |
| groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0"; |
| function = "du"; |
| }; |
| |
| hscif1_pins: hscif1 { |
| groups = "hscif1_data_a", "hscif1_ctrl_a"; |
| function = "hscif1"; |
| }; |
| |
| i2c2_pins: i2c2 { |
| groups = "i2c2_a"; |
| function = "i2c2"; |
| }; |
| |
| irq0_pins: irq0 { |
| groups = "intc_ex_irq0"; |
| function = "intc_ex"; |
| }; |
| |
| keys_pins: keys { |
| pins = "GP_5_17", "GP_5_20", "GP_5_22"; |
| bias-pull-up; |
| }; |
| |
| pwm1_pins: pwm1 { |
| groups = "pwm1_a"; |
| function = "pwm1"; |
| }; |
| |
| scif1_pins: scif1 { |
| groups = "scif1_data_a", "scif1_ctrl"; |
| function = "scif1"; |
| }; |
| |
| scif2_pins: scif2 { |
| groups = "scif2_data_a"; |
| function = "scif2"; |
| }; |
| |
| scif_clk_pins: scif_clk { |
| groups = "scif_clk_a"; |
| function = "scif_clk"; |
| }; |
| |
| sdhi0_pins: sd0 { |
| groups = "sdhi0_data4", "sdhi0_ctrl"; |
| function = "sdhi0"; |
| power-source = <3300>; |
| }; |
| |
| sdhi0_pins_uhs: sd0_uhs { |
| groups = "sdhi0_data4", "sdhi0_ctrl"; |
| function = "sdhi0"; |
| power-source = <1800>; |
| }; |
| |
| sdhi2_pins: sd2 { |
| groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; |
| function = "sdhi2"; |
| power-source = <1800>; |
| }; |
| |
| sdhi3_pins: sd3 { |
| groups = "sdhi3_data4", "sdhi3_ctrl"; |
| function = "sdhi3"; |
| power-source = <3300>; |
| }; |
| |
| sdhi3_pins_uhs: sd3_uhs { |
| groups = "sdhi3_data4", "sdhi3_ctrl"; |
| function = "sdhi3"; |
| power-source = <1800>; |
| }; |
| |
| sound_pins: sound { |
| groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; |
| function = "ssi"; |
| }; |
| |
| sound_clk_pins: sound_clk { |
| groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", |
| "audio_clkout_a", "audio_clkout3_a"; |
| function = "audio_clk"; |
| }; |
| |
| usb0_pins: usb0 { |
| groups = "usb0"; |
| function = "usb0"; |
| }; |
| |
| usb1_pins: usb1 { |
| mux { |
| groups = "usb1"; |
| function = "usb1"; |
| }; |
| |
| ovc { |
| pins = "GP_6_27"; |
| bias-pull-up; |
| }; |
| |
| pwen { |
| pins = "GP_6_26"; |
| bias-pull-down; |
| }; |
| }; |
| |
| usb30_pins: usb30 { |
| groups = "usb30"; |
| function = "usb30"; |
| }; |
| }; |
| |
| &pwm1 { |
| pinctrl-0 = <&pwm1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &rcar_sound { |
| pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; |
| pinctrl-names = "default"; |
| |
| /* Single DAI */ |
| #sound-dai-cells = <0>; |
| |
| /* audio_clkout0/1/2/3 */ |
| #clock-cells = <1>; |
| clock-frequency = <12288000 11289600>; |
| |
| status = "okay"; |
| |
| /* update <audio_clk_b> to <cs2000> */ |
| clocks = <&cpg CPG_MOD 1005>, |
| <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, |
| <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, |
| <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, |
| <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, |
| <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, |
| <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, |
| <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, |
| <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, |
| <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, |
| <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, |
| <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, |
| <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, |
| <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, |
| <&audio_clk_a>, <&cs2000>, |
| <&audio_clk_c>, |
| <&cpg CPG_CORE CPG_AUDIO_CLK_I>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| rsnd_port0: port@0 { |
| reg = <0>; |
| rsnd_endpoint0: endpoint { |
| remote-endpoint = <&ak4613_endpoint>; |
| |
| dai-format = "left_j"; |
| bitclock-master = <&rsnd_endpoint0>; |
| frame-master = <&rsnd_endpoint0>; |
| |
| playback = <&ssi0>, <&src0>, <&dvc0>; |
| capture = <&ssi1>, <&src1>, <&dvc1>; |
| }; |
| }; |
| |
| rsnd_port1: port@1 { |
| reg = <1>; |
| rsnd_endpoint1: endpoint { |
| remote-endpoint = <&dw_hdmi0_snd_in>; |
| |
| dai-format = "i2s"; |
| bitclock-master = <&rsnd_endpoint1>; |
| frame-master = <&rsnd_endpoint1>; |
| |
| playback = <&ssi2>; |
| }; |
| }; |
| |
| #ifdef SOC_HAS_HDMI1 |
| rsnd_port2: port@2 { |
| reg = <2>; |
| rsnd_endpoint2: endpoint { |
| remote-endpoint = <&dw_hdmi1_snd_in>; |
| |
| dai-format = "i2s"; |
| bitclock-master = <&rsnd_endpoint2>; |
| frame-master = <&rsnd_endpoint2>; |
| |
| playback = <&ssi3>; |
| }; |
| }; |
| #endif /* SOC_HAS_HDMI1 */ |
| }; |
| }; |
| |
| &rwdt { |
| timeout-sec = <60>; |
| status = "okay"; |
| }; |
| |
| #ifdef SOC_HAS_SATA |
| &sata { |
| status = "okay"; |
| }; |
| #endif /* SOC_HAS_SATA */ |
| |
| &scif1 { |
| pinctrl-0 = <&scif1_pins>; |
| pinctrl-names = "default"; |
| |
| uart-has-rtscts; |
| /* Please only enable hscif1 or scif1 */ |
| /* status = "okay"; */ |
| }; |
| |
| &scif2 { |
| pinctrl-0 = <&scif2_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &scif_clk { |
| clock-frequency = <14745600>; |
| }; |
| |
| &sdhi0 { |
| pinctrl-0 = <&sdhi0_pins>; |
| pinctrl-1 = <&sdhi0_pins_uhs>; |
| pinctrl-names = "default", "state_uhs"; |
| |
| vmmc-supply = <&vcc_sdhi0>; |
| vqmmc-supply = <&vccq_sdhi0>; |
| cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; |
| bus-width = <4>; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| status = "okay"; |
| }; |
| |
| &sdhi2 { |
| /* used for on-board 8bit eMMC */ |
| pinctrl-0 = <&sdhi2_pins>; |
| pinctrl-1 = <&sdhi2_pins>; |
| pinctrl-names = "default", "state_uhs"; |
| |
| vmmc-supply = <®_3p3v>; |
| vqmmc-supply = <®_1p8v>; |
| bus-width = <8>; |
| mmc-hs200-1_8v; |
| mmc-hs400-1_8v; |
| no-sd; |
| no-sdio; |
| non-removable; |
| fixed-emmc-driver-type = <1>; |
| full-pwr-cycle-in-suspend; |
| status = "okay"; |
| }; |
| |
| &sdhi3 { |
| pinctrl-0 = <&sdhi3_pins>; |
| pinctrl-1 = <&sdhi3_pins_uhs>; |
| pinctrl-names = "default", "state_uhs"; |
| |
| vmmc-supply = <&vcc_sdhi3>; |
| vqmmc-supply = <&vccq_sdhi3>; |
| cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; |
| bus-width = <4>; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| status = "okay"; |
| }; |
| |
| &ssi1 { |
| shared-pin; |
| }; |
| |
| &usb_extal_clk { |
| clock-frequency = <50000000>; |
| }; |
| |
| &usb2_phy0 { |
| pinctrl-0 = <&usb0_pins>; |
| pinctrl-names = "default"; |
| |
| vbus-supply = <&vbus0_usb2>; |
| status = "okay"; |
| }; |
| |
| &usb2_phy1 { |
| pinctrl-0 = <&usb1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &usb3_peri0 { |
| phys = <&usb3_phy0>; |
| phy-names = "usb"; |
| |
| companion = <&xhci0>; |
| |
| status = "okay"; |
| }; |
| |
| &usb3_phy0 { |
| status = "okay"; |
| }; |
| |
| &usb3s0_clk { |
| clock-frequency = <100000000>; |
| }; |
| |
| &vin0 { |
| status = "okay"; |
| }; |
| |
| &vin1 { |
| status = "okay"; |
| }; |
| |
| &vin2 { |
| status = "okay"; |
| }; |
| |
| &vin3 { |
| status = "okay"; |
| }; |
| |
| &vin4 { |
| status = "okay"; |
| }; |
| |
| &vin5 { |
| status = "okay"; |
| }; |
| |
| &vin6 { |
| status = "okay"; |
| }; |
| |
| &vin7 { |
| status = "okay"; |
| }; |
| |
| &xhci0 { |
| pinctrl-0 = <&usb30_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| #ifdef SOC_HAS_USB2_CH2 |
| &ehci2 { |
| status = "okay"; |
| }; |
| |
| &ohci2 { |
| status = "okay"; |
| }; |
| |
| &pfc { |
| usb2_pins: usb2 { |
| groups = "usb2"; |
| function = "usb2"; |
| }; |
| }; |
| |
| &usb2_phy2 { |
| pinctrl-0 = <&usb2_pins>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| #endif /* SOC_HAS_USB2_CH2 */ |
