| * Freescale i.MX6 PCIe interface |
| |
| This PCIe host controller is based on the Synopsis Designware PCIe IP |
| and thus inherits all the common properties defined in designware-pcie.txt. |
| |
| Required properties: |
| - compatible: |
| - "fsl,imx6q-pcie" |
| - "fsl,imx6sx-pcie", |
| - "fsl,imx6qp-pcie" |
| - "fsl,imx7d-pcie" |
| - reg: base address and length of the PCIe controller |
| - interrupts: A list of interrupt outputs of the controller. Must contain an |
| entry for each entry in the interrupt-names property. |
| - interrupt-names: Must include the following entries: |
| - "msi": The interrupt that is asserted when an MSI is received |
| - clock-names: Must include the following additional entries: |
| - "pcie_phy" |
| |
| Optional properties: |
| - fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 |
| - fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 |
| - fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 |
| - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 |
| - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 |
| - fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for |
| gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs |
| do not meet gen2 jitter requirements and thus for gen2 capability a gen2 |
| compliant clock generator should be used and configured. |
| - reset-gpio: Should specify the GPIO for controlling the PCI bus device reset |
| signal. It's not polarity aware and defaults to active-low reset sequence |
| (L=reset state, H=operation state). |
| - reset-gpio-active-high: If present then the reset sequence using the GPIO |
| specified in the "reset-gpio" property is reversed (H=reset state, |
| L=operation state). |
| - vpcie-supply: Should specify the regulator in charge of PCIe port power. |
| The regulator will be enabled when initializing the PCIe host and |
| disabled either as part of the init process or when shutting down the |
| host. |
| |
| Additional required properties for imx6sx-pcie: |
| - clock names: Must include the following additional entries: |
| - "pcie_inbound_axi" |
| |
| Additional required properties for imx7d-pcie: |
| - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain |
| - resets: Must contain phandles to PCIe-related reset lines exposed by SRC |
| IP block |
| - reset-names: Must contain the following entires: |
| - "pciephy" |
| - "apps" |
| |
| Example: |
| |
| pcie@0x01000000 { |
| compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; |
| reg = <0x01ffc000 0x04000>, |
| <0x01f00000 0x80000>; |
| reg-names = "dbi", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 |
| 0x81000000 0 0 0x01f80000 0 0x00010000 |
| 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks 144>, <&clks 206>, <&clks 189>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy"; |
| }; |