| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| /* |
| * Copyright (c) 2014 Protonic Holland |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| chosen { |
| stdout-path = &uart4; |
| }; |
| |
| reg_3v3: regulator-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| reg_usb_h1_vbus: regulator-h1-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "h1-vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_usb_otg_vbus: regulator-otg-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "otg-vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &can1 { |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| temperature-sensor@70 { |
| compatible = "ti,tmp103"; |
| reg = <0x70>; |
| }; |
| }; |
| |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_h1_vbus>; |
| phy_type = "utmi"; |
| dr_mode = "host"; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| phy_type = "utmi"; |
| dr_mode = "host"; |
| over-current-active-low; |
| status = "okay"; |
| }; |
| |
| &usbphynop1 { |
| status = "disabled"; |
| }; |
| |
| &usbphynop2 { |
| status = "disabled"; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| bus-width = <8>; |
| non-removable; |
| no-1-8-v; |
| no-sd; |
| no-sdio; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_can1: can1grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b008 |
| MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b008 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 |
| MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_uart4: uart4grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 |
| MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 |
| MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 |
| MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 |
| MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 |
| MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 |
| MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 |
| MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 |
| MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 |
| MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 |
| MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 |
| MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 |
| MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 |
| >; |
| }; |
| }; |
