| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (c) 2019, Linaro Limited |
| |
| #include <linux/clk.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/mfd/core.h> |
| #include <linux/mfd/wcd934x/registers.h> |
| #include <linux/mfd/wcd934x/wcd934x.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/slimbus.h> |
| |
| #define WCD934X_REGMAP_IRQ_REG(_irq, _off, _mask) \ |
| [_irq] = { \ |
| .reg_offset = (_off), \ |
| .mask = (_mask), \ |
| .type = { \ |
| .type_reg_offset = (_off), \ |
| .types_supported = IRQ_TYPE_EDGE_BOTH, \ |
| .type_reg_mask = (_mask), \ |
| .type_level_low_val = (_mask), \ |
| .type_level_high_val = (_mask), \ |
| .type_falling_val = 0, \ |
| .type_rising_val = 0, \ |
| }, \ |
| } |
| |
| static const struct mfd_cell wcd934x_devices[] = { |
| { |
| .name = "wcd934x-codec", |
| }, { |
| .name = "wcd934x-gpio", |
| .of_compatible = "qcom,wcd9340-gpio", |
| }, { |
| .name = "wcd934x-soundwire", |
| .of_compatible = "qcom,soundwire-v1.3.0", |
| }, |
| }; |
| |
| static const struct regmap_irq wcd934x_irqs[] = { |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_SLIMBUS, 0, BIT(0)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_HPH_PA_OCPL_FAULT, 0, BIT(2)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_HPH_PA_OCPR_FAULT, 0, BIT(3)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_MBHC_SW_DET, 1, BIT(0)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_MBHC_ELECT_INS_REM_DET, 1, BIT(1)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_MBHC_BUTTON_PRESS_DET, 1, BIT(2)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_MBHC_BUTTON_RELEASE_DET, 1, BIT(3)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_MBHC_ELECT_INS_REM_LEG_DET, 1, BIT(4)), |
| WCD934X_REGMAP_IRQ_REG(WCD934X_IRQ_SOUNDWIRE, 2, BIT(4)), |
| }; |
| |
| static const struct regmap_irq_chip wcd934x_regmap_irq_chip = { |
| .name = "wcd934x_irq", |
| .status_base = WCD934X_INTR_PIN1_STATUS0, |
| .mask_base = WCD934X_INTR_PIN1_MASK0, |
| .ack_base = WCD934X_INTR_PIN1_CLEAR0, |
| .type_base = WCD934X_INTR_LEVEL0, |
| .num_type_reg = 4, |
| .type_in_mask = false, |
| .num_regs = 4, |
| .irqs = wcd934x_irqs, |
| .num_irqs = ARRAY_SIZE(wcd934x_irqs), |
| }; |
| |
| static bool wcd934x_is_volatile_register(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case WCD934X_INTR_PIN1_STATUS0...WCD934X_INTR_PIN2_CLEAR3: |
| case WCD934X_SWR_AHB_BRIDGE_RD_DATA_0: |
| case WCD934X_SWR_AHB_BRIDGE_RD_DATA_1: |
| case WCD934X_SWR_AHB_BRIDGE_RD_DATA_2: |
| case WCD934X_SWR_AHB_BRIDGE_RD_DATA_3: |
| case WCD934X_SWR_AHB_BRIDGE_ACCESS_STATUS: |
| case WCD934X_ANA_MBHC_RESULT_3: |
| case WCD934X_ANA_MBHC_RESULT_2: |
| case WCD934X_ANA_MBHC_RESULT_1: |
| case WCD934X_ANA_MBHC_MECH: |
| case WCD934X_ANA_MBHC_ELECT: |
| case WCD934X_ANA_MBHC_ZDET: |
| case WCD934X_ANA_MICB2: |
| case WCD934X_ANA_RCO: |
| case WCD934X_ANA_BIAS: |
| return true; |
| default: |
| return false; |
| } |
| }; |
| |
| static const struct regmap_range_cfg wcd934x_ranges[] = { |
| { .name = "WCD934X", |
| .range_min = 0x0, |
| .range_max = WCD934X_MAX_REGISTER, |
| .selector_reg = WCD934X_SEL_REGISTER, |
| .selector_mask = WCD934X_SEL_MASK, |
| .selector_shift = WCD934X_SEL_SHIFT, |
| .window_start = WCD934X_WINDOW_START, |
| .window_len = WCD934X_WINDOW_LENGTH, |
| }, |
| }; |
| |
| static struct regmap_config wcd934x_regmap_config = { |
| .reg_bits = 16, |
| .val_bits = 8, |
| .cache_type = REGCACHE_RBTREE, |
| .max_register = 0xffff, |
| .can_multi_write = true, |
| .ranges = wcd934x_ranges, |
| .num_ranges = ARRAY_SIZE(wcd934x_ranges), |
| .volatile_reg = wcd934x_is_volatile_register, |
| }; |
| |
| static int wcd934x_bring_up(struct wcd934x_ddata *ddata) |
| { |
| struct regmap *regmap = ddata->regmap; |
| u16 id_minor, id_major; |
| int ret; |
| |
| ret = regmap_bulk_read(regmap, WCD934X_CHIP_TIER_CTRL_CHIP_ID_BYTE0, |
| (u8 *)&id_minor, sizeof(u16)); |
| if (ret) |
| return ret; |
| |
| ret = regmap_bulk_read(regmap, WCD934X_CHIP_TIER_CTRL_CHIP_ID_BYTE2, |
| (u8 *)&id_major, sizeof(u16)); |
| if (ret) |
| return ret; |
| |
| dev_info(ddata->dev, "WCD934x chip id major 0x%x, minor 0x%x\n", |
| id_major, id_minor); |
| |
| regmap_write(regmap, WCD934X_CODEC_RPM_RST_CTL, 0x01); |
| regmap_write(regmap, WCD934X_SIDO_NEW_VOUT_A_STARTUP, 0x19); |
| regmap_write(regmap, WCD934X_SIDO_NEW_VOUT_D_STARTUP, 0x15); |
| /* Add 1msec delay for VOUT to settle */ |
| usleep_range(1000, 1100); |
| regmap_write(regmap, WCD934X_CODEC_RPM_PWR_CDC_DIG_HM_CTL, 0x5); |
| regmap_write(regmap, WCD934X_CODEC_RPM_PWR_CDC_DIG_HM_CTL, 0x7); |
| regmap_write(regmap, WCD934X_CODEC_RPM_RST_CTL, 0x3); |
| regmap_write(regmap, WCD934X_CODEC_RPM_RST_CTL, 0x7); |
| regmap_write(regmap, WCD934X_CODEC_RPM_PWR_CDC_DIG_HM_CTL, 0x3); |
| |
| return 0; |
| } |
| |
| static int wcd934x_slim_status_up(struct slim_device *sdev) |
| { |
| struct device *dev = &sdev->dev; |
| struct wcd934x_ddata *ddata; |
| int ret; |
| |
| ddata = dev_get_drvdata(dev); |
| |
| ddata->regmap = regmap_init_slimbus(sdev, &wcd934x_regmap_config); |
| if (IS_ERR(ddata->regmap)) { |
| dev_err(dev, "Error allocating slim regmap\n"); |
| return PTR_ERR(ddata->regmap); |
| } |
| |
| ret = wcd934x_bring_up(ddata); |
| if (ret) { |
| dev_err(dev, "Failed to bring up WCD934X: err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = devm_regmap_add_irq_chip(dev, ddata->regmap, ddata->irq, |
| IRQF_TRIGGER_HIGH, 0, |
| &wcd934x_regmap_irq_chip, |
| &ddata->irq_data); |
| if (ret) { |
| dev_err(dev, "Failed to add IRQ chip: err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = mfd_add_devices(dev, PLATFORM_DEVID_AUTO, wcd934x_devices, |
| ARRAY_SIZE(wcd934x_devices), NULL, 0, NULL); |
| if (ret) { |
| dev_err(dev, "Failed to add child devices: err = %d\n", |
| ret); |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| static int wcd934x_slim_status(struct slim_device *sdev, |
| enum slim_device_status status) |
| { |
| switch (status) { |
| case SLIM_DEVICE_STATUS_UP: |
| return wcd934x_slim_status_up(sdev); |
| case SLIM_DEVICE_STATUS_DOWN: |
| mfd_remove_devices(&sdev->dev); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int wcd934x_slim_probe(struct slim_device *sdev) |
| { |
| struct device *dev = &sdev->dev; |
| struct device_node *np = dev->of_node; |
| struct wcd934x_ddata *ddata; |
| struct gpio_desc *reset_gpio; |
| int ret; |
| |
| ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL); |
| if (!ddata) |
| return -ENOMEM; |
| |
| ddata->irq = of_irq_get(np, 0); |
| if (ddata->irq < 0) |
| return dev_err_probe(ddata->dev, ddata->irq, |
| "Failed to get IRQ\n"); |
| |
| ddata->extclk = devm_clk_get(dev, "extclk"); |
| if (IS_ERR(ddata->extclk)) { |
| dev_err(dev, "Failed to get extclk"); |
| return PTR_ERR(ddata->extclk); |
| } |
| |
| ddata->supplies[0].supply = "vdd-buck"; |
| ddata->supplies[1].supply = "vdd-buck-sido"; |
| ddata->supplies[2].supply = "vdd-tx"; |
| ddata->supplies[3].supply = "vdd-rx"; |
| ddata->supplies[4].supply = "vdd-io"; |
| |
| ret = regulator_bulk_get(dev, WCD934X_MAX_SUPPLY, ddata->supplies); |
| if (ret) { |
| dev_err(dev, "Failed to get supplies: err = %d\n", ret); |
| return ret; |
| } |
| |
| ret = regulator_bulk_enable(WCD934X_MAX_SUPPLY, ddata->supplies); |
| if (ret) { |
| dev_err(dev, "Failed to enable supplies: err = %d\n", ret); |
| return ret; |
| } |
| |
| /* |
| * For WCD934X, it takes about 600us for the Vout_A and |
| * Vout_D to be ready after BUCK_SIDO is powered up. |
| * SYS_RST_N shouldn't be pulled high during this time |
| */ |
| usleep_range(600, 650); |
| reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); |
| if (IS_ERR(reset_gpio)) { |
| ret = dev_err_probe(dev, PTR_ERR(reset_gpio), |
| "Failed to get reset gpio\n"); |
| goto err_disable_regulators; |
| } |
| msleep(20); |
| gpiod_set_value(reset_gpio, 1); |
| msleep(20); |
| |
| ddata->dev = dev; |
| dev_set_drvdata(dev, ddata); |
| |
| return 0; |
| |
| err_disable_regulators: |
| regulator_bulk_disable(WCD934X_MAX_SUPPLY, ddata->supplies); |
| return ret; |
| } |
| |
| static void wcd934x_slim_remove(struct slim_device *sdev) |
| { |
| struct wcd934x_ddata *ddata = dev_get_drvdata(&sdev->dev); |
| |
| regulator_bulk_disable(WCD934X_MAX_SUPPLY, ddata->supplies); |
| mfd_remove_devices(&sdev->dev); |
| } |
| |
| static const struct slim_device_id wcd934x_slim_id[] = { |
| { SLIM_MANF_ID_QCOM, SLIM_PROD_CODE_WCD9340, |
| SLIM_DEV_IDX_WCD9340, SLIM_DEV_INSTANCE_ID_WCD9340 }, |
| {} |
| }; |
| |
| static struct slim_driver wcd934x_slim_driver = { |
| .driver = { |
| .name = "wcd934x-slim", |
| }, |
| .probe = wcd934x_slim_probe, |
| .remove = wcd934x_slim_remove, |
| .device_status = wcd934x_slim_status, |
| .id_table = wcd934x_slim_id, |
| }; |
| |
| module_slim_driver(wcd934x_slim_driver); |
| MODULE_DESCRIPTION("WCD934X slim driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("slim:217:250:*"); |
| MODULE_AUTHOR("Srinivas Kandagatla <srinivas.kandagatla@linaro.org>"); |