drivers/net/wireless/intel/iwlwifi/iwl-prph.h - linux - Git at Google

 /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
  * Copyright (C) 2005-2014, 2018-2022 Intel Corporation
  * Copyright (C) 2013-2015 Intel Mobile Communications GmbH
  * Copyright (C) 2016 Intel Deutschland GmbH
  */
 #ifndef	__iwl_prph_h__
 #define __iwl_prph_h__
 #include <linux/bitfield.h>

 /*
  * Registers in this file are internal, not PCI bus memory mapped.
  * Driver accesses these via HBUS_TARG_PRPH_* registers.
  */
 #define PRPH_BASE	(0x00000)
 #define PRPH_END	(0xFFFFF)

 /* APMG (power management) constants */
 #define APMG_BASE			(PRPH_BASE + 0x3000)
 #define APMG_CLK_CTRL_REG		(APMG_BASE + 0x0000)
 #define APMG_CLK_EN_REG			(APMG_BASE + 0x0004)
 #define APMG_CLK_DIS_REG		(APMG_BASE + 0x0008)
 #define APMG_PS_CTRL_REG		(APMG_BASE + 0x000c)
 #define APMG_PCIDEV_STT_REG		(APMG_BASE + 0x0010)
 #define APMG_RFKILL_REG			(APMG_BASE + 0x0014)
 #define APMG_RTC_INT_STT_REG		(APMG_BASE + 0x001c)
 #define APMG_RTC_INT_MSK_REG		(APMG_BASE + 0x0020)
 #define APMG_DIGITAL_SVR_REG		(APMG_BASE + 0x0058)
 #define APMG_ANALOG_SVR_REG		(APMG_BASE + 0x006C)

 #define APMS_CLK_VAL_MRB_FUNC_MODE	(0x00000001)
 #define APMG_CLK_VAL_DMA_CLK_RQT	(0x00000200)
 #define APMG_CLK_VAL_BSM_CLK_RQT	(0x00000800)

 #define APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS	(0x00400000)
 #define APMG_PS_CTRL_VAL_RESET_REQ		(0x04000000)
 #define APMG_PS_CTRL_MSK_PWR_SRC		(0x03000000)
 #define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN		(0x00000000)
 #define APMG_PS_CTRL_VAL_PWR_SRC_VAUX		(0x02000000)
 #define APMG_SVR_VOLTAGE_CONFIG_BIT_MSK	(0x000001E0) /* bit 8:5 */
 #define APMG_SVR_DIGITAL_VOLTAGE_1_32		(0x00000060)

 #define APMG_PCIDEV_STT_VAL_PERSIST_DIS	(0x00000200)
 #define APMG_PCIDEV_STT_VAL_L1_ACT_DIS	(0x00000800)
 #define APMG_PCIDEV_STT_VAL_WAKE_ME	(0x00004000)

 #define APMG_RTC_INT_STT_RFKILL		(0x10000000)

 /* Device system time */
 #define DEVICE_SYSTEM_TIME_REG 0xA0206C

 /* Device NMI register and value for 8000 family and lower hw's */
 #define DEVICE_SET_NMI_REG 0x00a01c30
 #define DEVICE_SET_NMI_VAL_DRV BIT(7)
 /* Device NMI register and value for 9000 family and above hw's */
 #define UREG_NIC_SET_NMI_DRIVER 0x00a05c10
 #define UREG_NIC_SET_NMI_DRIVER_NMI_FROM_DRIVER BIT(24)
 #define UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE (BIT(24) | BIT(25))

 /* Shared registers (0x0..0x3ff, via target indirect or periphery */
 #define SHR_BASE	0x00a10000

 /* Shared GP1 register */
 #define SHR_APMG_GP1_REG		0x01dc
 #define SHR_APMG_GP1_REG_PRPH		(SHR_BASE + SHR_APMG_GP1_REG)
 #define SHR_APMG_GP1_WF_XTAL_LP_EN	0x00000004
 #define SHR_APMG_GP1_CHICKEN_BIT_SELECT	0x80000000

 /* Shared DL_CFG register */
 #define SHR_APMG_DL_CFG_REG			0x01c4
 #define SHR_APMG_DL_CFG_REG_PRPH		(SHR_BASE + SHR_APMG_DL_CFG_REG)
 #define SHR_APMG_DL_CFG_RTCS_CLK_SELECTOR_MSK	0x000000c0
 #define SHR_APMG_DL_CFG_RTCS_CLK_INTERNAL_XTAL	0x00000080
 #define SHR_APMG_DL_CFG_DL_CLOCK_POWER_UP	0x00000100

 /* Shared APMG_XTAL_CFG register */
 #define SHR_APMG_XTAL_CFG_REG		0x1c0
 #define SHR_APMG_XTAL_CFG_XTAL_ON_REQ	0x80000000

 /*
  * Device reset for family 8000
  * write to bit 24 in order to reset the CPU
 */
 #define RELEASE_CPU_RESET		(0x300C)
 #define RELEASE_CPU_RESET_BIT		BIT(24)

 /*****************************************************************************
  *                        7000/3000 series SHR DTS addresses                 *
  *****************************************************************************/

 #define SHR_MISC_WFM_DTS_EN	(0x00a10024)
 #define DTSC_CFG_MODE		(0x00a10604)
 #define DTSC_VREF_AVG		(0x00a10648)
 #define DTSC_VREF5_AVG		(0x00a1064c)
 #define DTSC_CFG_MODE_PERIODIC	(0x2)
 #define DTSC_PTAT_AVG		(0x00a10650)


 /**
  * Tx Scheduler
  *
  * The Tx Scheduler selects the next frame to be transmitted, choosing TFDs
  * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
  * host DRAM.  It steers each frame's Tx command (which contains the frame
  * data) into one of up to 7 prioritized Tx DMA FIFO channels within the
  * device.  A queue maps to only one (selectable by driver) Tx DMA channel,
  * but one DMA channel may take input from several queues.
  *
  * Tx DMA FIFOs have dedicated purposes.
  *
  * For 5000 series and up, they are used differently
  * (cf. iwl5000_default_queue_to_tx_fifo in iwl-5000.c):
  *
  * 0 -- EDCA BK (background) frames, lowest priority
  * 1 -- EDCA BE (best effort) frames, normal priority
  * 2 -- EDCA VI (video) frames, higher priority
  * 3 -- EDCA VO (voice) and management frames, highest priority
  * 4 -- unused
  * 5 -- unused
  * 6 -- unused
  * 7 -- Commands
  *
  * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
  * In addition, driver can map the remaining queues to Tx DMA/FIFO
  * channels 0-3 to support 11n aggregation via EDCA DMA channels.
  *
  * The driver sets up each queue to work in one of two modes:
  *
  * 1)  Scheduler-Ack, in which the scheduler automatically supports a
  *     block-ack (BA) window of up to 64 TFDs.  In this mode, each queue
  *     contains TFDs for a unique combination of Recipient Address (RA)
  *     and Traffic Identifier (TID), that is, traffic of a given
  *     Quality-Of-Service (QOS) priority, destined for a single station.
  *
  *     In scheduler-ack mode, the scheduler keeps track of the Tx status of
  *     each frame within the BA window, including whether it's been transmitted,
  *     and whether it's been acknowledged by the receiving station.  The device
  *     automatically processes block-acks received from the receiving STA,
  *     and reschedules un-acked frames to be retransmitted (successful
  *     Tx completion may end up being out-of-order).
  *
  *     The driver must maintain the queue's Byte Count table in host DRAM
  *     for this mode.
  *     This mode does not support fragmentation.
  *
  * 2)  FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
  *     The device may automatically retry Tx, but will retry only one frame
  *     at a time, until receiving ACK from receiving station, or reaching
  *     retry limit and giving up.
  *
  *     The command queue (#4/#9) must use this mode!
  *     This mode does not require use of the Byte Count table in host DRAM.
  *
  * Driver controls scheduler operation via 3 means:
  * 1)  Scheduler registers
  * 2)  Shared scheduler data base in internal SRAM
  * 3)  Shared data in host DRAM
  *
  * Initialization:
  *
  * When loading, driver should allocate memory for:
  * 1)  16 TFD circular buffers, each with space for (typically) 256 TFDs.
  * 2)  16 Byte Count circular buffers in 16 KBytes contiguous memory
  *     (1024 bytes for each queue).
  *
  * After receiving "Alive" response from uCode, driver must initialize
  * the scheduler (especially for queue #4/#9, the command queue, otherwise
  * the driver can't issue commands!):
  */
 #define SCD_MEM_LOWER_BOUND		(0x0000)

 /**
  * Max Tx window size is the max number of contiguous TFDs that the scheduler
  * can keep track of at one time when creating block-ack chains of frames.
  * Note that "64" matches the number of ack bits in a block-ack packet.
  */
 #define SCD_WIN_SIZE				64
 #define SCD_FRAME_LIMIT				64

 #define SCD_TXFIFO_POS_TID			(0)
 #define SCD_TXFIFO_POS_RA			(4)
 #define SCD_QUEUE_RA_TID_MAP_RATID_MSK	(0x01FF)

 /* agn SCD */
 #define SCD_QUEUE_STTS_REG_POS_TXF	(0)
 #define SCD_QUEUE_STTS_REG_POS_ACTIVE	(3)
 #define SCD_QUEUE_STTS_REG_POS_WSL	(4)
 #define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (19)
 #define SCD_QUEUE_STTS_REG_MSK		(0x017F0000)

 #define SCD_QUEUE_CTX_REG1_CREDIT		(0x00FFFF00)
 #define SCD_QUEUE_CTX_REG1_SUPER_CREDIT		(0xFF000000)
 #define SCD_QUEUE_CTX_REG1_VAL(_n, _v)		FIELD_PREP(SCD_QUEUE_CTX_REG1_ ## _n, _v)

 #define SCD_QUEUE_CTX_REG2_WIN_SIZE		(0x0000007F)
 #define SCD_QUEUE_CTX_REG2_FRAME_LIMIT		(0x007F0000)
 #define SCD_QUEUE_CTX_REG2_VAL(_n, _v)		FIELD_PREP(SCD_QUEUE_CTX_REG2_ ## _n, _v)

 #define SCD_GP_CTRL_ENABLE_31_QUEUES		BIT(0)
 #define SCD_GP_CTRL_AUTO_ACTIVE_MODE		BIT(18)

 /* Context Data */
 #define SCD_CONTEXT_MEM_LOWER_BOUND	(SCD_MEM_LOWER_BOUND + 0x600)
 #define SCD_CONTEXT_MEM_UPPER_BOUND	(SCD_MEM_LOWER_BOUND + 0x6A0)

 /* Tx status */
 #define SCD_TX_STTS_MEM_LOWER_BOUND	(SCD_MEM_LOWER_BOUND + 0x6A0)
 #define SCD_TX_STTS_MEM_UPPER_BOUND	(SCD_MEM_LOWER_BOUND + 0x7E0)

 /* Translation Data */
 #define SCD_TRANS_TBL_MEM_LOWER_BOUND	(SCD_MEM_LOWER_BOUND + 0x7E0)
 #define SCD_TRANS_TBL_MEM_UPPER_BOUND	(SCD_MEM_LOWER_BOUND + 0x808)

 #define SCD_CONTEXT_QUEUE_OFFSET(x)\
 	(SCD_CONTEXT_MEM_LOWER_BOUND + ((x) * 8))

 #define SCD_TX_STTS_QUEUE_OFFSET(x)\
 	(SCD_TX_STTS_MEM_LOWER_BOUND + ((x) * 16))

 #define SCD_TRANS_TBL_OFFSET_QUEUE(x) \
 	((SCD_TRANS_TBL_MEM_LOWER_BOUND + ((x) * 2)) & 0xfffc)

 #define SCD_BASE			(PRPH_BASE + 0xa02c00)

 #define SCD_SRAM_BASE_ADDR	(SCD_BASE + 0x0)
 #define SCD_DRAM_BASE_ADDR	(SCD_BASE + 0x8)
 #define SCD_AIT			(SCD_BASE + 0x0c)
 #define SCD_TXFACT		(SCD_BASE + 0x10)
 #define SCD_ACTIVE		(SCD_BASE + 0x14)
 #define SCD_QUEUECHAIN_SEL	(SCD_BASE + 0xe8)
 #define SCD_CHAINEXT_EN		(SCD_BASE + 0x244)
 #define SCD_AGGR_SEL		(SCD_BASE + 0x248)
 #define SCD_INTERRUPT_MASK	(SCD_BASE + 0x108)
 #define SCD_GP_CTRL		(SCD_BASE + 0x1a8)
 #define SCD_EN_CTRL		(SCD_BASE + 0x254)

 /*********************** END TX SCHEDULER *************************************/

 /* Oscillator clock */
 #define OSC_CLK				(0xa04068)
 #define OSC_CLK_FORCE_CONTROL		(0x8)

 #define FH_UCODE_LOAD_STATUS		(0x1AF0)

 /*
  * Replacing FH_UCODE_LOAD_STATUS
  * This register is writen by driver and is read by uCode during boot flow.
  * Note this address is cleared after MAC reset.
  */
 #define UREG_UCODE_LOAD_STATUS		(0xa05c40)
 #define UREG_CPU_INIT_RUN		(0xa05c44)

 #define LMPM_SECURE_UCODE_LOAD_CPU1_HDR_ADDR	(0x1E78)
 #define LMPM_SECURE_UCODE_LOAD_CPU2_HDR_ADDR	(0x1E7C)

 #define LMPM_SECURE_CPU1_HDR_MEM_SPACE		(0x420000)
 #define LMPM_SECURE_CPU2_HDR_MEM_SPACE		(0x420400)

 #define LMAC2_PRPH_OFFSET		(0x100000)

 /* Rx FIFO */
 #define RXF_SIZE_ADDR			(0xa00c88)
 #define RXF_RD_D_SPACE			(0xa00c40)
 #define RXF_RD_WR_PTR			(0xa00c50)
 #define RXF_RD_RD_PTR			(0xa00c54)
 #define RXF_RD_FENCE_PTR		(0xa00c4c)
 #define RXF_SET_FENCE_MODE		(0xa00c14)
 #define RXF_LD_WR2FENCE		(0xa00c1c)
 #define RXF_FIFO_RD_FENCE_INC		(0xa00c68)
 #define RXF_SIZE_BYTE_CND_POS		(7)
 #define RXF_SIZE_BYTE_CNT_MSK		(0x3ff << RXF_SIZE_BYTE_CND_POS)
 #define RXF_DIFF_FROM_PREV		(0x200)
 #define RXF2C_DIFF_FROM_PREV		(0x4e00)

 #define RXF_LD_FENCE_OFFSET_ADDR	(0xa00c10)
 #define RXF_FIFO_RD_FENCE_ADDR		(0xa00c0c)

 /* Tx FIFO */
 #define TXF_FIFO_ITEM_CNT		(0xa00438)
 #define TXF_WR_PTR			(0xa00414)
 #define TXF_RD_PTR			(0xa00410)
 #define TXF_FENCE_PTR			(0xa00418)
 #define TXF_LOCK_FENCE			(0xa00424)
 #define TXF_LARC_NUM			(0xa0043c)
 #define TXF_READ_MODIFY_DATA		(0xa00448)
 #define TXF_READ_MODIFY_ADDR		(0xa0044c)

 /* UMAC Internal Tx Fifo */
 #define TXF_CPU2_FIFO_ITEM_CNT		(0xA00538)
 #define TXF_CPU2_WR_PTR		(0xA00514)
 #define TXF_CPU2_RD_PTR		(0xA00510)
 #define TXF_CPU2_FENCE_PTR		(0xA00518)
 #define TXF_CPU2_LOCK_FENCE		(0xA00524)
 #define TXF_CPU2_NUM			(0xA0053C)
 #define TXF_CPU2_READ_MODIFY_DATA	(0xA00548)
 #define TXF_CPU2_READ_MODIFY_ADDR	(0xA0054C)

 /* Radio registers access */
 #define RSP_RADIO_CMD			(0xa02804)
 #define RSP_RADIO_RDDAT			(0xa02814)
 #define RADIO_RSP_ADDR_POS		(6)
 #define RADIO_RSP_RD_CMD		(3)

 /* LTR control (Qu only) */
 #define HPM_MAC_LTR_CSR			0xa0348c
 #define HPM_MAC_LRT_ENABLE_ALL		0xf
 /* also uses CSR_LTR_* for values */
 #define HPM_UMAC_LTR			0xa03480

 /* FW monitor */
 #define MON_BUFF_SAMPLE_CTL		(0xa03c00)
 #define MON_BUFF_BASE_ADDR		(0xa03c1c)
 #define MON_BUFF_END_ADDR		(0xa03c40)
 #define MON_BUFF_WRPTR			(0xa03c44)
 #define MON_BUFF_CYCLE_CNT		(0xa03c48)
 /* FW monitor family 8000 and on */
 #define MON_BUFF_BASE_ADDR_VER2		(0xa03c1c)
 #define MON_BUFF_END_ADDR_VER2		(0xa03c20)
 #define MON_BUFF_WRPTR_VER2		(0xa03c24)
 #define MON_BUFF_CYCLE_CNT_VER2		(0xa03c28)
 #define MON_BUFF_SHIFT_VER2		(0x8)
 /* FW monitor familiy AX210 and on */
 #define DBGC_CUR_DBGBUF_BASE_ADDR_LSB		(0xd03c20)
 #define DBGC_CUR_DBGBUF_BASE_ADDR_MSB		(0xd03c24)
 #define DBGC_CUR_DBGBUF_STATUS			(0xd03c1c)
 #define DBGC_DBGBUF_WRAP_AROUND			(0xd03c2c)
 #define DBGC_CUR_DBGBUF_STATUS_OFFSET_MSK	(0x00ffffff)
 #define DBGC_CUR_DBGBUF_STATUS_IDX_MSK		(0x0f000000)

 #define MON_DMARB_RD_CTL_ADDR		(0xa03c60)
 #define MON_DMARB_RD_DATA_ADDR		(0xa03c5c)

 #define DBGC_IN_SAMPLE			(0xa03c00)
 #define DBGC_OUT_CTRL			(0xa03c0c)

 /* M2S registers */
 #define LDBG_M2S_BUF_WPTR			(0xa0476c)
 #define LDBG_M2S_BUF_WRAP_CNT			(0xa04774)
 #define LDBG_M2S_BUF_WPTR_VAL_MSK		(0x000fffff)
 #define LDBG_M2S_BUF_WRAP_CNT_VAL_MSK		(0x000fffff)

 /* enable the ID buf for read */
 #define WFPM_PS_CTL_CLR			0xA0300C
 #define WFMP_MAC_ADDR_0			0xA03080
 #define WFMP_MAC_ADDR_1			0xA03084
 #define LMPM_PMG_EN			0xA01CEC
 #define RADIO_REG_SYS_MANUAL_DFT_0	0xAD4078
 #define RFIC_REG_RD			0xAD0470
 #define WFPM_CTRL_REG			0xA03030
 #define WFPM_OTP_CFG1_ADDR		0x00a03098
 #define WFPM_OTP_CFG1_IS_JACKET_BIT	BIT(4)
 #define WFPM_OTP_CFG1_IS_CDB_BIT	BIT(5)
 #define WFPM_OTP_BZ_BNJ_JACKET_BIT	5
 #define WFPM_OTP_BZ_BNJ_CDB_BIT		4
 #define WFPM_OTP_CFG1_IS_JACKET(_val)   (((_val) & 0x00000020) >> WFPM_OTP_BZ_BNJ_JACKET_BIT)
 #define WFPM_OTP_CFG1_IS_CDB(_val)      (((_val) & 0x00000010) >> WFPM_OTP_BZ_BNJ_CDB_BIT)


 #define WFPM_GP2			0xA030B4

 /* DBGI SRAM Register details */
 #define DBGI_SRAM_TARGET_ACCESS_RDATA_LSB		0x00A2E154
 #define DBGI_SRAM_TARGET_ACCESS_RDATA_MSB		0x00A2E158
 #define DBGI_SRAM_FIFO_POINTERS				0x00A2E148
 #define DBGI_SRAM_FIFO_POINTERS_WR_PTR_MSK		0x00000FFF

 enum {
 	ENABLE_WFPM = BIT(31),
 	WFPM_AUX_CTL_AUX_IF_MAC_OWNER_MSK	= 0x80000000,
 };

 #define CNVI_AUX_MISC_CHIP				0xA200B0
 #define CNVR_AUX_MISC_CHIP				0xA2B800
 #define CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM		0xA29890
 #define CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR	0xA29938
 #define CNVI_SCU_SEQ_DATA_DW9				0xA27488

 #define PREG_AUX_BUS_WPROT_0		0xA04CC0

 /* device family 9000 WPROT register */
 #define PREG_PRPH_WPROT_9000		0xA04CE0
 /* device family 22000 WPROT register */
 #define PREG_PRPH_WPROT_22000		0xA04D00

 #define SB_MODIFY_CFG_FLAG		0xA03088
 #define SB_CFG_RESIDES_IN_OTP_MASK	0x10
 #define SB_CPU_1_STATUS			0xA01E30
 #define SB_CPU_2_STATUS			0xA01E34
 #define UMAG_SB_CPU_1_STATUS		0xA038C0
 #define UMAG_SB_CPU_2_STATUS		0xA038C4
 #define UMAG_GEN_HW_STATUS		0xA038C8
 #define UREG_UMAC_CURRENT_PC		0xa05c18
 #define UREG_LMAC1_CURRENT_PC		0xa05c1c
 #define UREG_LMAC2_CURRENT_PC		0xa05c20

 #define WFPM_LMAC1_PD_NOTIFICATION      0xa0338c
 #define WFPM_ARC1_PD_NOTIFICATION       0xa03044
 #define HPM_SECONDARY_DEVICE_STATE      0xa03404
 #define WFPM_MAC_OTP_CFG7_ADDR		0xa03338
 #define WFPM_MAC_OTP_CFG7_DATA		0xa0333c


 /* For UMAG_GEN_HW_STATUS reg check */
 enum {
 	UMAG_GEN_HW_IS_FPGA = BIT(1),
 };

 /* FW chicken bits */
 #define LMPM_CHICK			0xA01FF8
 enum {
 	LMPM_CHICK_EXTENDED_ADDR_SPACE = BIT(0),
 };

 /* FW chicken bits */
 #define LMPM_PAGE_PASS_NOTIF			0xA03824
 enum {
 	LMPM_PAGE_PASS_NOTIF_POS = BIT(20),
 };

 /*
  * CRF ID register
  *
  * type: bits 0-11
  * reserved: bits 12-18
  * slave_exist: bit 19
  * dash: bits 20-23
  * step: bits 24-26
  * flavor: bits 27-31
  */
 #define REG_CRF_ID_TYPE(val)		(((val) & 0x00000FFF) >> 0)
 #define REG_CRF_ID_SLAVE(val)		(((val) & 0x00080000) >> 19)
 #define REG_CRF_ID_DASH(val)		(((val) & 0x00F00000) >> 20)
 #define REG_CRF_ID_STEP(val)		(((val) & 0x07000000) >> 24)
 #define REG_CRF_ID_FLAVOR(val)		(((val) & 0xF8000000) >> 27)

 #define UREG_CHICK		(0xA05C00)
 #define UREG_CHICK_MSI_ENABLE	BIT(24)
 #define UREG_CHICK_MSIX_ENABLE	BIT(25)

 #define SD_REG_VER		0xa29600
 #define SD_REG_VER_GEN2		0x00a2b800

 #define REG_CRF_ID_TYPE_JF_1			0x201
 #define REG_CRF_ID_TYPE_JF_2			0x202
 #define REG_CRF_ID_TYPE_HR_CDB			0x503
 #define REG_CRF_ID_TYPE_HR_NONE_CDB		0x504
 #define REG_CRF_ID_TYPE_HR_NONE_CDB_1X1	0x501
 #define REG_CRF_ID_TYPE_HR_NONE_CDB_CCP	0x532
 #define REG_CRF_ID_TYPE_GF			0x410
 #define REG_CRF_ID_TYPE_GF_TC			0xF08
 #define REG_CRF_ID_TYPE_MR			0x810
 #define REG_CRF_ID_TYPE_FM			0x910
 #define REG_CRF_ID_TYPE_FMI			0x930
 #define REG_CRF_ID_TYPE_FMR			0x900

 #define HPM_DEBUG			0xA03440
 #define PERSISTENCE_BIT			BIT(12)
 #define PREG_WFPM_ACCESS		BIT(12)

 #define HPM_HIPM_GEN_CFG			0xA03458
 #define HPM_HIPM_GEN_CFG_CR_PG_EN		BIT(0)
 #define HPM_HIPM_GEN_CFG_CR_SLP_EN		BIT(1)
 #define HPM_HIPM_GEN_CFG_CR_FORCE_ACTIVE	BIT(10)

 #define UREG_DOORBELL_TO_ISR6		0xA05C04
 #define UREG_DOORBELL_TO_ISR6_NMI_BIT	BIT(0)
 #define UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE (BIT(0) | BIT(1))
 #define UREG_DOORBELL_TO_ISR6_SUSPEND	BIT(18)
 #define UREG_DOORBELL_TO_ISR6_RESUME	BIT(19)
 #define UREG_DOORBELL_TO_ISR6_PNVM	BIT(20)

 /*
  * From BZ family driver triggers this bit for suspend and resume
  * The driver should update CSR_IPC_SLEEP_CONTROL before triggering
  * this interrupt with suspend/resume value
  */
 #define UREG_DOORBELL_TO_ISR6_SLEEP_CTRL	BIT(31)

 #define CNVI_MBOX_C			0xA3400C

 #define FSEQ_ERROR_CODE			0xA340C8
 #define FSEQ_TOP_INIT_VERSION		0xA34038
 #define FSEQ_CNVIO_INIT_VERSION		0xA3403C
 #define FSEQ_OTP_VERSION		0xA340FC
 #define FSEQ_TOP_CONTENT_VERSION	0xA340F4
 #define FSEQ_ALIVE_TOKEN		0xA340F0
 #define FSEQ_CNVI_ID			0xA3408C
 #define FSEQ_CNVR_ID			0xA34090

 #define IWL_D3_SLEEP_STATUS_SUSPEND	0xD3
 #define IWL_D3_SLEEP_STATUS_RESUME	0xD0

 #define WMAL_INDRCT_RD_CMD1_OPMOD_POS 28
 #define WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK 0xFFFFF
 #define WMAL_CMD_READ_BURST_ACCESS 2
 #define WMAL_MRSPF_1 0xADFC20
 #define WMAL_INDRCT_RD_CMD1 0xADFD44
 #define WMAL_INDRCT_CMD1 0xADFC14
 #define WMAL_INDRCT_CMD(addr) \
 	((WMAL_CMD_READ_BURST_ACCESS << WMAL_INDRCT_RD_CMD1_OPMOD_POS) | \
 	 ((addr) & WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK))

 #define WFPM_LMAC1_PS_CTL_RW 0xA03380
 #define WFPM_LMAC2_PS_CTL_RW 0xA033C0
 #define WFPM_PS_CTL_RW_PHYRF_PD_FSM_CURSTATE_MSK 0x0000000F
 #define WFPM_PHYRF_STATE_ON 5
 #define HBUS_TIMEOUT 0xA5A5A5A1
 #define WFPM_DPHY_OFF 0xDF10FF

 #define REG_OTP_MINOR 0xA0333C

 #define WFPM_LMAC2_PD_NOTIFICATION 0xA033CC
 #define WFPM_LMAC2_PD_RE_READ BIT(31)

 #endif				/* __iwl_prph_h__ */
	/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
	/*
	* Copyright (C) 2005-2014, 2018-2022 Intel Corporation
	* Copyright (C) 2013-2015 Intel Mobile Communications GmbH
	* Copyright (C) 2016 Intel Deutschland GmbH
	*/
	#ifndef __iwl_prph_h__
	#define __iwl_prph_h__
	#include <linux/bitfield.h>

	/*
	* Registers in this file are internal, not PCI bus memory mapped.
	* Driver accesses these via HBUS_TARG_PRPH_* registers.
	*/
	#define PRPH_BASE (0x00000)
	#define PRPH_END (0xFFFFF)

	/* APMG (power management) constants */
	#define APMG_BASE (PRPH_BASE + 0x3000)
	#define APMG_CLK_CTRL_REG (APMG_BASE + 0x0000)
	#define APMG_CLK_EN_REG (APMG_BASE + 0x0004)
	#define APMG_CLK_DIS_REG (APMG_BASE + 0x0008)
	#define APMG_PS_CTRL_REG (APMG_BASE + 0x000c)
	#define APMG_PCIDEV_STT_REG (APMG_BASE + 0x0010)
	#define APMG_RFKILL_REG (APMG_BASE + 0x0014)
	#define APMG_RTC_INT_STT_REG (APMG_BASE + 0x001c)
	#define APMG_RTC_INT_MSK_REG (APMG_BASE + 0x0020)
	#define APMG_DIGITAL_SVR_REG (APMG_BASE + 0x0058)
	#define APMG_ANALOG_SVR_REG (APMG_BASE + 0x006C)

	#define APMS_CLK_VAL_MRB_FUNC_MODE (0x00000001)
	#define APMG_CLK_VAL_DMA_CLK_RQT (0x00000200)
	#define APMG_CLK_VAL_BSM_CLK_RQT (0x00000800)

	#define APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS (0x00400000)
	#define APMG_PS_CTRL_VAL_RESET_REQ (0x04000000)
	#define APMG_PS_CTRL_MSK_PWR_SRC (0x03000000)
	#define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN (0x00000000)
	#define APMG_PS_CTRL_VAL_PWR_SRC_VAUX (0x02000000)
	#define APMG_SVR_VOLTAGE_CONFIG_BIT_MSK (0x000001E0) /* bit 8:5 */
	#define APMG_SVR_DIGITAL_VOLTAGE_1_32 (0x00000060)

	#define APMG_PCIDEV_STT_VAL_PERSIST_DIS (0x00000200)
	#define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800)
	#define APMG_PCIDEV_STT_VAL_WAKE_ME (0x00004000)

	#define APMG_RTC_INT_STT_RFKILL (0x10000000)

	/* Device system time */
	#define DEVICE_SYSTEM_TIME_REG 0xA0206C

	/* Device NMI register and value for 8000 family and lower hw's */
	#define DEVICE_SET_NMI_REG 0x00a01c30
	#define DEVICE_SET_NMI_VAL_DRV BIT(7)
	/* Device NMI register and value for 9000 family and above hw's */
	#define UREG_NIC_SET_NMI_DRIVER 0x00a05c10
	#define UREG_NIC_SET_NMI_DRIVER_NMI_FROM_DRIVER BIT(24)
	#define UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE (BIT(24) \| BIT(25))

	/* Shared registers (0x0..0x3ff, via target indirect or periphery */
	#define SHR_BASE 0x00a10000

	/* Shared GP1 register */
	#define SHR_APMG_GP1_REG 0x01dc
	#define SHR_APMG_GP1_REG_PRPH (SHR_BASE + SHR_APMG_GP1_REG)
	#define SHR_APMG_GP1_WF_XTAL_LP_EN 0x00000004
	#define SHR_APMG_GP1_CHICKEN_BIT_SELECT 0x80000000

	/* Shared DL_CFG register */
	#define SHR_APMG_DL_CFG_REG 0x01c4
	#define SHR_APMG_DL_CFG_REG_PRPH (SHR_BASE + SHR_APMG_DL_CFG_REG)
	#define SHR_APMG_DL_CFG_RTCS_CLK_SELECTOR_MSK 0x000000c0
	#define SHR_APMG_DL_CFG_RTCS_CLK_INTERNAL_XTAL 0x00000080
	#define SHR_APMG_DL_CFG_DL_CLOCK_POWER_UP 0x00000100

	/* Shared APMG_XTAL_CFG register */
	#define SHR_APMG_XTAL_CFG_REG 0x1c0
	#define SHR_APMG_XTAL_CFG_XTAL_ON_REQ 0x80000000

	/*
	* Device reset for family 8000
	* write to bit 24 in order to reset the CPU
	*/
	#define RELEASE_CPU_RESET (0x300C)
	#define RELEASE_CPU_RESET_BIT BIT(24)

	/*****************************************************************************
	* 7000/3000 series SHR DTS addresses *
	*****************************************************************************/

	#define SHR_MISC_WFM_DTS_EN (0x00a10024)
	#define DTSC_CFG_MODE (0x00a10604)
	#define DTSC_VREF_AVG (0x00a10648)
	#define DTSC_VREF5_AVG (0x00a1064c)
	#define DTSC_CFG_MODE_PERIODIC (0x2)
	#define DTSC_PTAT_AVG (0x00a10650)


	/**
	* Tx Scheduler
	*
	* The Tx Scheduler selects the next frame to be transmitted, choosing TFDs
	* (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
	* host DRAM. It steers each frame's Tx command (which contains the frame
	* data) into one of up to 7 prioritized Tx DMA FIFO channels within the
	* device. A queue maps to only one (selectable by driver) Tx DMA channel,
	* but one DMA channel may take input from several queues.
	*
	* Tx DMA FIFOs have dedicated purposes.
	*
	* For 5000 series and up, they are used differently
	* (cf. iwl5000_default_queue_to_tx_fifo in iwl-5000.c):
	*
	* 0 -- EDCA BK (background) frames, lowest priority
	* 1 -- EDCA BE (best effort) frames, normal priority
	* 2 -- EDCA VI (video) frames, higher priority
	* 3 -- EDCA VO (voice) and management frames, highest priority
	* 4 -- unused
	* 5 -- unused
	* 6 -- unused
	* 7 -- Commands
	*
	* Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
	* In addition, driver can map the remaining queues to Tx DMA/FIFO
	* channels 0-3 to support 11n aggregation via EDCA DMA channels.
	*
	* The driver sets up each queue to work in one of two modes:
	*
	* 1) Scheduler-Ack, in which the scheduler automatically supports a
	* block-ack (BA) window of up to 64 TFDs. In this mode, each queue
	* contains TFDs for a unique combination of Recipient Address (RA)
	* and Traffic Identifier (TID), that is, traffic of a given
	* Quality-Of-Service (QOS) priority, destined for a single station.
	*
	* In scheduler-ack mode, the scheduler keeps track of the Tx status of
	* each frame within the BA window, including whether it's been transmitted,
	* and whether it's been acknowledged by the receiving station. The device
	* automatically processes block-acks received from the receiving STA,
	* and reschedules un-acked frames to be retransmitted (successful
	* Tx completion may end up being out-of-order).
	*
	* The driver must maintain the queue's Byte Count table in host DRAM
	* for this mode.
	* This mode does not support fragmentation.
	*
	* 2) FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
	* The device may automatically retry Tx, but will retry only one frame
	* at a time, until receiving ACK from receiving station, or reaching
	* retry limit and giving up.
	*
	* The command queue (#4/#9) must use this mode!
	* This mode does not require use of the Byte Count table in host DRAM.
	*
	* Driver controls scheduler operation via 3 means:
	* 1) Scheduler registers
	* 2) Shared scheduler data base in internal SRAM
	* 3) Shared data in host DRAM
	*
	* Initialization:
	*
	* When loading, driver should allocate memory for:
	* 1) 16 TFD circular buffers, each with space for (typically) 256 TFDs.
	* 2) 16 Byte Count circular buffers in 16 KBytes contiguous memory
	* (1024 bytes for each queue).
	*
	* After receiving "Alive" response from uCode, driver must initialize
	* the scheduler (especially for queue #4/#9, the command queue, otherwise
	* the driver can't issue commands!):
	*/
	#define SCD_MEM_LOWER_BOUND (0x0000)

	/**
	* Max Tx window size is the max number of contiguous TFDs that the scheduler
	* can keep track of at one time when creating block-ack chains of frames.
	* Note that "64" matches the number of ack bits in a block-ack packet.
	*/
	#define SCD_WIN_SIZE 64
	#define SCD_FRAME_LIMIT 64

	#define SCD_TXFIFO_POS_TID (0)
	#define SCD_TXFIFO_POS_RA (4)
	#define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)

	/* agn SCD */
	#define SCD_QUEUE_STTS_REG_POS_TXF (0)
	#define SCD_QUEUE_STTS_REG_POS_ACTIVE (3)
	#define SCD_QUEUE_STTS_REG_POS_WSL (4)
	#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (19)
	#define SCD_QUEUE_STTS_REG_MSK (0x017F0000)

	#define SCD_QUEUE_CTX_REG1_CREDIT (0x00FFFF00)
	#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT (0xFF000000)
	#define SCD_QUEUE_CTX_REG1_VAL(_n, _v) FIELD_PREP(SCD_QUEUE_CTX_REG1_ ## _n, _v)

	#define SCD_QUEUE_CTX_REG2_WIN_SIZE (0x0000007F)
	#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT (0x007F0000)
	#define SCD_QUEUE_CTX_REG2_VAL(_n, _v) FIELD_PREP(SCD_QUEUE_CTX_REG2_ ## _n, _v)

	#define SCD_GP_CTRL_ENABLE_31_QUEUES BIT(0)
	#define SCD_GP_CTRL_AUTO_ACTIVE_MODE BIT(18)

	/* Context Data */
	#define SCD_CONTEXT_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x600)
	#define SCD_CONTEXT_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x6A0)

	/* Tx status */
	#define SCD_TX_STTS_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x6A0)
	#define SCD_TX_STTS_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x7E0)

	/* Translation Data */
	#define SCD_TRANS_TBL_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x7E0)
	#define SCD_TRANS_TBL_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x808)

	#define SCD_CONTEXT_QUEUE_OFFSET(x)\
	(SCD_CONTEXT_MEM_LOWER_BOUND + ((x) * 8))

	#define SCD_TX_STTS_QUEUE_OFFSET(x)\
	(SCD_TX_STTS_MEM_LOWER_BOUND + ((x) * 16))

	#define SCD_TRANS_TBL_OFFSET_QUEUE(x) \
	((SCD_TRANS_TBL_MEM_LOWER_BOUND + ((x) * 2)) & 0xfffc)

	#define SCD_BASE (PRPH_BASE + 0xa02c00)

	#define SCD_SRAM_BASE_ADDR (SCD_BASE + 0x0)
	#define SCD_DRAM_BASE_ADDR (SCD_BASE + 0x8)
	#define SCD_AIT (SCD_BASE + 0x0c)
	#define SCD_TXFACT (SCD_BASE + 0x10)
	#define SCD_ACTIVE (SCD_BASE + 0x14)
	#define SCD_QUEUECHAIN_SEL (SCD_BASE + 0xe8)
	#define SCD_CHAINEXT_EN (SCD_BASE + 0x244)
	#define SCD_AGGR_SEL (SCD_BASE + 0x248)
	#define SCD_INTERRUPT_MASK (SCD_BASE + 0x108)
	#define SCD_GP_CTRL (SCD_BASE + 0x1a8)
	#define SCD_EN_CTRL (SCD_BASE + 0x254)

	/********************* END TX SCHEDULER ***********************************/

	/* Oscillator clock */
	#define OSC_CLK (0xa04068)
	#define OSC_CLK_FORCE_CONTROL (0x8)

	#define FH_UCODE_LOAD_STATUS (0x1AF0)

	/*
	* Replacing FH_UCODE_LOAD_STATUS
	* This register is writen by driver and is read by uCode during boot flow.
	* Note this address is cleared after MAC reset.
	*/
	#define UREG_UCODE_LOAD_STATUS (0xa05c40)
	#define UREG_CPU_INIT_RUN (0xa05c44)

	#define LMPM_SECURE_UCODE_LOAD_CPU1_HDR_ADDR (0x1E78)
	#define LMPM_SECURE_UCODE_LOAD_CPU2_HDR_ADDR (0x1E7C)

	#define LMPM_SECURE_CPU1_HDR_MEM_SPACE (0x420000)
	#define LMPM_SECURE_CPU2_HDR_MEM_SPACE (0x420400)

	#define LMAC2_PRPH_OFFSET (0x100000)

	/* Rx FIFO */
	#define RXF_SIZE_ADDR (0xa00c88)
	#define RXF_RD_D_SPACE (0xa00c40)
	#define RXF_RD_WR_PTR (0xa00c50)
	#define RXF_RD_RD_PTR (0xa00c54)
	#define RXF_RD_FENCE_PTR (0xa00c4c)
	#define RXF_SET_FENCE_MODE (0xa00c14)
	#define RXF_LD_WR2FENCE (0xa00c1c)
	#define RXF_FIFO_RD_FENCE_INC (0xa00c68)
	#define RXF_SIZE_BYTE_CND_POS (7)
	#define RXF_SIZE_BYTE_CNT_MSK (0x3ff << RXF_SIZE_BYTE_CND_POS)
	#define RXF_DIFF_FROM_PREV (0x200)
	#define RXF2C_DIFF_FROM_PREV (0x4e00)

	#define RXF_LD_FENCE_OFFSET_ADDR (0xa00c10)
	#define RXF_FIFO_RD_FENCE_ADDR (0xa00c0c)

	/* Tx FIFO */
	#define TXF_FIFO_ITEM_CNT (0xa00438)
	#define TXF_WR_PTR (0xa00414)
	#define TXF_RD_PTR (0xa00410)
	#define TXF_FENCE_PTR (0xa00418)
	#define TXF_LOCK_FENCE (0xa00424)
	#define TXF_LARC_NUM (0xa0043c)
	#define TXF_READ_MODIFY_DATA (0xa00448)
	#define TXF_READ_MODIFY_ADDR (0xa0044c)

	/* UMAC Internal Tx Fifo */
	#define TXF_CPU2_FIFO_ITEM_CNT (0xA00538)
	#define TXF_CPU2_WR_PTR (0xA00514)
	#define TXF_CPU2_RD_PTR (0xA00510)
	#define TXF_CPU2_FENCE_PTR (0xA00518)
	#define TXF_CPU2_LOCK_FENCE (0xA00524)
	#define TXF_CPU2_NUM (0xA0053C)
	#define TXF_CPU2_READ_MODIFY_DATA (0xA00548)
	#define TXF_CPU2_READ_MODIFY_ADDR (0xA0054C)

	/* Radio registers access */
	#define RSP_RADIO_CMD (0xa02804)
	#define RSP_RADIO_RDDAT (0xa02814)
	#define RADIO_RSP_ADDR_POS (6)
	#define RADIO_RSP_RD_CMD (3)

	/* LTR control (Qu only) */
	#define HPM_MAC_LTR_CSR 0xa0348c
	#define HPM_MAC_LRT_ENABLE_ALL 0xf
	/* also uses CSR_LTR_* for values */
	#define HPM_UMAC_LTR 0xa03480

	/* FW monitor */
	#define MON_BUFF_SAMPLE_CTL (0xa03c00)
	#define MON_BUFF_BASE_ADDR (0xa03c1c)
	#define MON_BUFF_END_ADDR (0xa03c40)
	#define MON_BUFF_WRPTR (0xa03c44)
	#define MON_BUFF_CYCLE_CNT (0xa03c48)
	/* FW monitor family 8000 and on */
	#define MON_BUFF_BASE_ADDR_VER2 (0xa03c1c)
	#define MON_BUFF_END_ADDR_VER2 (0xa03c20)
	#define MON_BUFF_WRPTR_VER2 (0xa03c24)
	#define MON_BUFF_CYCLE_CNT_VER2 (0xa03c28)
	#define MON_BUFF_SHIFT_VER2 (0x8)
	/* FW monitor familiy AX210 and on */
	#define DBGC_CUR_DBGBUF_BASE_ADDR_LSB (0xd03c20)
	#define DBGC_CUR_DBGBUF_BASE_ADDR_MSB (0xd03c24)
	#define DBGC_CUR_DBGBUF_STATUS (0xd03c1c)
	#define DBGC_DBGBUF_WRAP_AROUND (0xd03c2c)
	#define DBGC_CUR_DBGBUF_STATUS_OFFSET_MSK (0x00ffffff)
	#define DBGC_CUR_DBGBUF_STATUS_IDX_MSK (0x0f000000)

	#define MON_DMARB_RD_CTL_ADDR (0xa03c60)
	#define MON_DMARB_RD_DATA_ADDR (0xa03c5c)

	#define DBGC_IN_SAMPLE (0xa03c00)
	#define DBGC_OUT_CTRL (0xa03c0c)

	/* M2S registers */
	#define LDBG_M2S_BUF_WPTR (0xa0476c)
	#define LDBG_M2S_BUF_WRAP_CNT (0xa04774)
	#define LDBG_M2S_BUF_WPTR_VAL_MSK (0x000fffff)
	#define LDBG_M2S_BUF_WRAP_CNT_VAL_MSK (0x000fffff)

	/* enable the ID buf for read */
	#define WFPM_PS_CTL_CLR 0xA0300C
	#define WFMP_MAC_ADDR_0 0xA03080
	#define WFMP_MAC_ADDR_1 0xA03084
	#define LMPM_PMG_EN 0xA01CEC
	#define RADIO_REG_SYS_MANUAL_DFT_0 0xAD4078
	#define RFIC_REG_RD 0xAD0470
	#define WFPM_CTRL_REG 0xA03030
	#define WFPM_OTP_CFG1_ADDR 0x00a03098
	#define WFPM_OTP_CFG1_IS_JACKET_BIT BIT(4)
	#define WFPM_OTP_CFG1_IS_CDB_BIT BIT(5)
	#define WFPM_OTP_BZ_BNJ_JACKET_BIT 5
	#define WFPM_OTP_BZ_BNJ_CDB_BIT 4
	#define WFPM_OTP_CFG1_IS_JACKET(_val) (((_val) & 0x00000020) >> WFPM_OTP_BZ_BNJ_JACKET_BIT)
	#define WFPM_OTP_CFG1_IS_CDB(_val) (((_val) & 0x00000010) >> WFPM_OTP_BZ_BNJ_CDB_BIT)


	#define WFPM_GP2 0xA030B4

	/* DBGI SRAM Register details */
	#define DBGI_SRAM_TARGET_ACCESS_RDATA_LSB 0x00A2E154
	#define DBGI_SRAM_TARGET_ACCESS_RDATA_MSB 0x00A2E158
	#define DBGI_SRAM_FIFO_POINTERS 0x00A2E148
	#define DBGI_SRAM_FIFO_POINTERS_WR_PTR_MSK 0x00000FFF

	enum {
	ENABLE_WFPM = BIT(31),
	WFPM_AUX_CTL_AUX_IF_MAC_OWNER_MSK = 0x80000000,
	};

	#define CNVI_AUX_MISC_CHIP 0xA200B0
	#define CNVR_AUX_MISC_CHIP 0xA2B800
	#define CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM 0xA29890
	#define CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR 0xA29938
	#define CNVI_SCU_SEQ_DATA_DW9 0xA27488

	#define PREG_AUX_BUS_WPROT_0 0xA04CC0

	/* device family 9000 WPROT register */
	#define PREG_PRPH_WPROT_9000 0xA04CE0
	/* device family 22000 WPROT register */
	#define PREG_PRPH_WPROT_22000 0xA04D00

	#define SB_MODIFY_CFG_FLAG 0xA03088
	#define SB_CFG_RESIDES_IN_OTP_MASK 0x10
	#define SB_CPU_1_STATUS 0xA01E30
	#define SB_CPU_2_STATUS 0xA01E34
	#define UMAG_SB_CPU_1_STATUS 0xA038C0
	#define UMAG_SB_CPU_2_STATUS 0xA038C4
	#define UMAG_GEN_HW_STATUS 0xA038C8
	#define UREG_UMAC_CURRENT_PC 0xa05c18
	#define UREG_LMAC1_CURRENT_PC 0xa05c1c
	#define UREG_LMAC2_CURRENT_PC 0xa05c20

	#define WFPM_LMAC1_PD_NOTIFICATION 0xa0338c
	#define WFPM_ARC1_PD_NOTIFICATION 0xa03044
	#define HPM_SECONDARY_DEVICE_STATE 0xa03404
	#define WFPM_MAC_OTP_CFG7_ADDR 0xa03338
	#define WFPM_MAC_OTP_CFG7_DATA 0xa0333c


	/* For UMAG_GEN_HW_STATUS reg check */
	enum {
	UMAG_GEN_HW_IS_FPGA = BIT(1),
	};

	/* FW chicken bits */
	#define LMPM_CHICK 0xA01FF8
	enum {
	LMPM_CHICK_EXTENDED_ADDR_SPACE = BIT(0),
	};

	/* FW chicken bits */
	#define LMPM_PAGE_PASS_NOTIF 0xA03824
	enum {
	LMPM_PAGE_PASS_NOTIF_POS = BIT(20),
	};

	/*
	* CRF ID register
	*
	* type: bits 0-11
	* reserved: bits 12-18
	* slave_exist: bit 19
	* dash: bits 20-23
	* step: bits 24-26
	* flavor: bits 27-31
	*/
	#define REG_CRF_ID_TYPE(val) (((val) & 0x00000FFF) >> 0)
	#define REG_CRF_ID_SLAVE(val) (((val) & 0x00080000) >> 19)
	#define REG_CRF_ID_DASH(val) (((val) & 0x00F00000) >> 20)
	#define REG_CRF_ID_STEP(val) (((val) & 0x07000000) >> 24)
	#define REG_CRF_ID_FLAVOR(val) (((val) & 0xF8000000) >> 27)

	#define UREG_CHICK (0xA05C00)
	#define UREG_CHICK_MSI_ENABLE BIT(24)
	#define UREG_CHICK_MSIX_ENABLE BIT(25)

	#define SD_REG_VER 0xa29600
	#define SD_REG_VER_GEN2 0x00a2b800

	#define REG_CRF_ID_TYPE_JF_1 0x201
	#define REG_CRF_ID_TYPE_JF_2 0x202
	#define REG_CRF_ID_TYPE_HR_CDB 0x503
	#define REG_CRF_ID_TYPE_HR_NONE_CDB 0x504
	#define REG_CRF_ID_TYPE_HR_NONE_CDB_1X1 0x501
	#define REG_CRF_ID_TYPE_HR_NONE_CDB_CCP 0x532
	#define REG_CRF_ID_TYPE_GF 0x410
	#define REG_CRF_ID_TYPE_GF_TC 0xF08
	#define REG_CRF_ID_TYPE_MR 0x810
	#define REG_CRF_ID_TYPE_FM 0x910
	#define REG_CRF_ID_TYPE_FMI 0x930
	#define REG_CRF_ID_TYPE_FMR 0x900

	#define HPM_DEBUG 0xA03440
	#define PERSISTENCE_BIT BIT(12)
	#define PREG_WFPM_ACCESS BIT(12)

	#define HPM_HIPM_GEN_CFG 0xA03458
	#define HPM_HIPM_GEN_CFG_CR_PG_EN BIT(0)
	#define HPM_HIPM_GEN_CFG_CR_SLP_EN BIT(1)
	#define HPM_HIPM_GEN_CFG_CR_FORCE_ACTIVE BIT(10)

	#define UREG_DOORBELL_TO_ISR6 0xA05C04
	#define UREG_DOORBELL_TO_ISR6_NMI_BIT BIT(0)
	#define UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE (BIT(0) \| BIT(1))
	#define UREG_DOORBELL_TO_ISR6_SUSPEND BIT(18)
	#define UREG_DOORBELL_TO_ISR6_RESUME BIT(19)
	#define UREG_DOORBELL_TO_ISR6_PNVM BIT(20)

	/*
	* From BZ family driver triggers this bit for suspend and resume
	* The driver should update CSR_IPC_SLEEP_CONTROL before triggering
	* this interrupt with suspend/resume value
	*/
	#define UREG_DOORBELL_TO_ISR6_SLEEP_CTRL BIT(31)

	#define CNVI_MBOX_C 0xA3400C

	#define FSEQ_ERROR_CODE 0xA340C8
	#define FSEQ_TOP_INIT_VERSION 0xA34038
	#define FSEQ_CNVIO_INIT_VERSION 0xA3403C
	#define FSEQ_OTP_VERSION 0xA340FC
	#define FSEQ_TOP_CONTENT_VERSION 0xA340F4
	#define FSEQ_ALIVE_TOKEN 0xA340F0
	#define FSEQ_CNVI_ID 0xA3408C
	#define FSEQ_CNVR_ID 0xA34090

	#define IWL_D3_SLEEP_STATUS_SUSPEND 0xD3
	#define IWL_D3_SLEEP_STATUS_RESUME 0xD0

	#define WMAL_INDRCT_RD_CMD1_OPMOD_POS 28
	#define WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK 0xFFFFF
	#define WMAL_CMD_READ_BURST_ACCESS 2
	#define WMAL_MRSPF_1 0xADFC20
	#define WMAL_INDRCT_RD_CMD1 0xADFD44
	#define WMAL_INDRCT_CMD1 0xADFC14
	#define WMAL_INDRCT_CMD(addr) \
	((WMAL_CMD_READ_BURST_ACCESS << WMAL_INDRCT_RD_CMD1_OPMOD_POS) \| \
	((addr) & WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK))

	#define WFPM_LMAC1_PS_CTL_RW 0xA03380
	#define WFPM_LMAC2_PS_CTL_RW 0xA033C0
	#define WFPM_PS_CTL_RW_PHYRF_PD_FSM_CURSTATE_MSK 0x0000000F
	#define WFPM_PHYRF_STATE_ON 5
	#define HBUS_TIMEOUT 0xA5A5A5A1
	#define WFPM_DPHY_OFF 0xDF10FF

	#define REG_OTP_MINOR 0xA0333C

	#define WFPM_LMAC2_PD_NOTIFICATION 0xA033CC
	#define WFPM_LMAC2_PD_RE_READ BIT(31)

	#endif /* __iwl_prph_h__ */