Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge

maintainers:
  - Benjamin Mugnier <benjamin.mugnier@foss.st.com>
  - Sylvain Petinot <sylvain.petinot@foss.st.com>

description:
  MIPID02 has two CSI-2 input ports, only one of those ports can be
  active at a time. Active port input stream will be de-serialized
  and its content outputted through PARALLEL output port.
  CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2
  second input port is a single lane 800Mbps. Both ports support clock
  and data lane polarity swap. First port also supports data lane swap.
  PARALLEL output port has a maximum width of 12 bits.
  Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888,
  RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.

properties:
  compatible:
    const: st,st-mipid02

  reg:
    maxItems: 1

  clocks:
    maxItems: 1

  clock-names:
    const: xclk

  VDDE-supply:
    description:
      Sensor digital IO supply. Must be 1.8 volts.

  VDDIN-supply:
    description:
      Sensor internal regulator supply. Must be 1.8 volts.

  reset-gpios:
    description:
      Reference to the GPIO connected to the xsdn pin, if any.
      This is an active low signal to the mipid02.

  ports:
    $ref: /schemas/graph.yaml#/properties/ports
    properties:
      port@0:
        $ref: /schemas/graph.yaml#/$defs/port-base
        unevaluatedProperties: false
        description: CSI-2 first input port
        properties:
          endpoint:
            $ref: /schemas/media/video-interfaces.yaml#
            unevaluatedProperties: false

            properties:
              data-lanes:
                description:
                  Single-lane operation shall be <1> or <2> .
                  Dual-lane operation shall be <1 2> or <2 1> .
                minItems: 1
                maxItems: 2

              lane-polarities:
                description:
                  Any lane can be inverted or not.
                minItems: 1
                maxItems: 2

            required:
              - data-lanes

      port@1:
        $ref: /schemas/graph.yaml#/$defs/port-base
        unevaluatedProperties: false
        description: CSI-2 second input port
        properties:
          endpoint:
            $ref: /schemas/media/video-interfaces.yaml#
            unevaluatedProperties: false

            properties:
              data-lanes:
                description:
                  Single-lane operation shall be <1> or <2> .
                maxItems: 1

              lane-polarities:
                description:
                  Any lane can be inverted or not.
                maxItems: 1

            required:
              - data-lanes

      port@2:
        $ref: /schemas/graph.yaml#/$defs/port-base
        unevaluatedProperties: false
        description: Output port
        properties:
          endpoint:
            $ref: /schemas/media/video-interfaces.yaml#
            unevaluatedProperties: false

            properties:
              bus-width:
                enum: [6, 7, 8, 10, 12]

            required:
              - bus-width

    anyOf:
      - required:
          - port@0
      - required:
          - port@1

    required:
      - port@2

additionalProperties: false

required:
  - compatible
  - reg
  - clocks
  - clock-names
  - VDDE-supply
  - VDDIN-supply
  - ports

examples:
  - |
    i2c {
        #address-cells = <1>;
        #size-cells = <0>;
        mipid02: csi2rx@14 {
            compatible = "st,st-mipid02";
            reg = <0x14>;
            status = "okay";
            clocks = <&clk_ext_camera_12>;
            clock-names = "xclk";
            VDDE-supply = <&vdd>;
            VDDIN-supply = <&vdd>;
            ports {
                #address-cells = <1>;
                #size-cells = <0>;
                port@0 {
                    reg = <0>;

                    ep0: endpoint {
                        data-lanes = <1 2>;
                        remote-endpoint = <&mipi_csi2_in>;
                    };
                };
                port@2 {
                    reg = <2>;

                    ep2: endpoint {
                        bus-width = <8>;
                        hsync-active = <0>;
                        vsync-active = <0>;
                        remote-endpoint = <&parallel_out>;
                    };
                };
            };
        };
    };

...