blob: 636ea430fbffaf0edfa246e8f51571c878c5dd4c [file] [log] [blame]
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: "http://devicetree.org/schemas/phy/qcom,qusb2-phy.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: Qualcomm QUSB2 phy controller
maintainers:
- Wesley Cheng <quic_wcheng@quicinc.com>
description:
QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
properties:
compatible:
oneOf:
- items:
- enum:
- qcom,ipq8074-qusb2-phy
- qcom,msm8953-qusb2-phy
- qcom,msm8996-qusb2-phy
- qcom,msm8998-qusb2-phy
- qcom,qcm2290-qusb2-phy
- qcom,sdm660-qusb2-phy
- qcom,ipq6018-qusb2-phy
- qcom,sm4250-qusb2-phy
- qcom,sm6115-qusb2-phy
- items:
- enum:
- qcom,sc7180-qusb2-phy
- qcom,sdm670-qusb2-phy
- qcom,sdm845-qusb2-phy
- qcom,sm6350-qusb2-phy
- const: qcom,qusb2-v2-phy
reg:
maxItems: 1
"#phy-cells":
const: 0
clocks:
minItems: 2
items:
- description: phy config clock
- description: 19.2 MHz ref clk
- description: phy interface clock (Optional)
clock-names:
minItems: 2
items:
- const: cfg_ahb
- const: ref
- const: iface
vdd-supply:
description:
Phandle to 0.9V regulator supply to PHY digital circuit.
vdda-pll-supply:
description:
Phandle to 1.8V regulator supply to PHY refclk pll block.
vdda-phy-dpdm-supply:
description:
Phandle to 3.1V regulator supply to Dp/Dm port signals.
resets:
maxItems: 1
description:
Phandle to reset to phy block.
nvmem-cells:
maxItems: 1
description:
Phandle to nvmem cell that contains 'HS Tx trim'
tuning parameter value for qusb2 phy.
qcom,tcsr-syscon:
description:
Phandle to TCSR syscon register region.
$ref: /schemas/types.yaml#/definitions/phandle
if:
properties:
compatible:
contains:
const: qcom,qusb2-v2-phy
then:
properties:
qcom,imp-res-offset-value:
description:
It is a 6 bit value that specifies offset to be
added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
tuning parameter that may vary for different boards of same SOC.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 63
default: 0
qcom,bias-ctrl-value:
description:
It is a 6 bit value that specifies bias-ctrl-value. It is a PHY
tuning parameter that may vary for different boards of same SOC.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 63
default: 32
qcom,charge-ctrl-value:
description:
It is a 2 bit value that specifies charge-ctrl-value. It is a PHY
tuning parameter that may vary for different boards of same SOC.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
default: 0
qcom,hstx-trim-value:
description:
It is a 4 bit value that specifies tuning for HSTX
output current.
Possible range is - 15mA to 24mA (stepsize of 600 uA).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 15
default: 3
qcom,preemphasis-level:
description:
It is a 2 bit value that specifies pre-emphasis level.
Possible range is 0 to 15% (stepsize of 5%).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
default: 2
qcom,preemphasis-width:
description:
It is a 1 bit value that specifies how long the HSTX
pre-emphasis (specified using qcom,preemphasis-level) must be in
effect. Duration could be half-bit of full-bit.
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 1
default: 0
qcom,hsdisc-trim-value:
description:
It is a 2 bit value tuning parameter that control disconnect
threshold and may vary for different boards of same SOC.
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
default: 0
required:
- compatible
- reg
- "#phy-cells"
- clocks
- clock-names
- vdd-supply
- vdda-pll-supply
- vdda-phy-dpdm-supply
- resets
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
hsusb_phy: phy@7411000 {
compatible = "qcom,msm8996-qusb2-phy";
reg = <0x7411000 0x180>;
#phy-cells = <0>;
clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
<&gcc GCC_RX1_USB2_CLKREF_CLK>;
clock-names = "cfg_ahb", "ref";
vdd-supply = <&pm8994_l28>;
vdda-pll-supply = <&pm8994_l12>;
vdda-phy-dpdm-supply = <&pm8994_l24>;
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
nvmem-cells = <&qusb2p_hstx_trim>;
};