| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * AD5758 Digital to analog converters driver |
| * |
| * Copyright 2018 Analog Devices Inc. |
| * |
| * TODO: Currently CRC is not supported in this driver |
| */ |
| #include <linux/bsearch.h> |
| #include <linux/delay.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/property.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/spi/spi.h> |
| #include <linux/gpio/consumer.h> |
| |
| #include <linux/iio/iio.h> |
| #include <linux/iio/sysfs.h> |
| |
| /* AD5758 registers definition */ |
| #define AD5758_NOP 0x00 |
| #define AD5758_DAC_INPUT 0x01 |
| #define AD5758_DAC_OUTPUT 0x02 |
| #define AD5758_CLEAR_CODE 0x03 |
| #define AD5758_USER_GAIN 0x04 |
| #define AD5758_USER_OFFSET 0x05 |
| #define AD5758_DAC_CONFIG 0x06 |
| #define AD5758_SW_LDAC 0x07 |
| #define AD5758_KEY 0x08 |
| #define AD5758_GP_CONFIG1 0x09 |
| #define AD5758_GP_CONFIG2 0x0A |
| #define AD5758_DCDC_CONFIG1 0x0B |
| #define AD5758_DCDC_CONFIG2 0x0C |
| #define AD5758_WDT_CONFIG 0x0F |
| #define AD5758_DIGITAL_DIAG_CONFIG 0x10 |
| #define AD5758_ADC_CONFIG 0x11 |
| #define AD5758_FAULT_PIN_CONFIG 0x12 |
| #define AD5758_TWO_STAGE_READBACK_SELECT 0x13 |
| #define AD5758_DIGITAL_DIAG_RESULTS 0x14 |
| #define AD5758_ANALOG_DIAG_RESULTS 0x15 |
| #define AD5758_STATUS 0x16 |
| #define AD5758_CHIP_ID 0x17 |
| #define AD5758_FREQ_MONITOR 0x18 |
| #define AD5758_DEVICE_ID_0 0x19 |
| #define AD5758_DEVICE_ID_1 0x1A |
| #define AD5758_DEVICE_ID_2 0x1B |
| #define AD5758_DEVICE_ID_3 0x1C |
| |
| /* AD5758_DAC_CONFIG */ |
| #define AD5758_DAC_CONFIG_RANGE_MSK GENMASK(3, 0) |
| #define AD5758_DAC_CONFIG_RANGE_MODE(x) (((x) & 0xF) << 0) |
| #define AD5758_DAC_CONFIG_INT_EN_MSK BIT(5) |
| #define AD5758_DAC_CONFIG_INT_EN_MODE(x) (((x) & 0x1) << 5) |
| #define AD5758_DAC_CONFIG_OUT_EN_MSK BIT(6) |
| #define AD5758_DAC_CONFIG_OUT_EN_MODE(x) (((x) & 0x1) << 6) |
| #define AD5758_DAC_CONFIG_SR_EN_MSK BIT(8) |
| #define AD5758_DAC_CONFIG_SR_EN_MODE(x) (((x) & 0x1) << 8) |
| #define AD5758_DAC_CONFIG_SR_CLOCK_MSK GENMASK(12, 9) |
| #define AD5758_DAC_CONFIG_SR_CLOCK_MODE(x) (((x) & 0xF) << 9) |
| #define AD5758_DAC_CONFIG_SR_STEP_MSK GENMASK(15, 13) |
| #define AD5758_DAC_CONFIG_SR_STEP_MODE(x) (((x) & 0x7) << 13) |
| |
| /* AD5758_KEY */ |
| #define AD5758_KEY_CODE_RESET_1 0x15FA |
| #define AD5758_KEY_CODE_RESET_2 0xAF51 |
| #define AD5758_KEY_CODE_SINGLE_ADC_CONV 0x1ADC |
| #define AD5758_KEY_CODE_RESET_WDT 0x0D06 |
| #define AD5758_KEY_CODE_CALIB_MEM_REFRESH 0xFCBA |
| |
| /* AD5758_DCDC_CONFIG1 */ |
| #define AD5758_DCDC_CONFIG1_DCDC_VPROG_MSK GENMASK(4, 0) |
| #define AD5758_DCDC_CONFIG1_DCDC_VPROG_MODE(x) (((x) & 0x1F) << 0) |
| #define AD5758_DCDC_CONFIG1_DCDC_MODE_MSK GENMASK(6, 5) |
| #define AD5758_DCDC_CONFIG1_DCDC_MODE_MODE(x) (((x) & 0x3) << 5) |
| |
| /* AD5758_DCDC_CONFIG2 */ |
| #define AD5758_DCDC_CONFIG2_ILIMIT_MSK GENMASK(3, 1) |
| #define AD5758_DCDC_CONFIG2_ILIMIT_MODE(x) (((x) & 0x7) << 1) |
| #define AD5758_DCDC_CONFIG2_INTR_SAT_3WI_MSK BIT(11) |
| #define AD5758_DCDC_CONFIG2_BUSY_3WI_MSK BIT(12) |
| |
| /* AD5758_DIGITAL_DIAG_RESULTS */ |
| #define AD5758_CAL_MEM_UNREFRESHED_MSK BIT(15) |
| |
| /* AD5758_ADC_CONFIG */ |
| #define AD5758_ADC_CONFIG_PPC_BUF_EN(x) (((x) & 0x1) << 11) |
| #define AD5758_ADC_CONFIG_PPC_BUF_MSK BIT(11) |
| |
| #define AD5758_WR_FLAG_MSK(x) (0x80 | ((x) & 0x1F)) |
| |
| #define AD5758_FULL_SCALE_MICRO 65535000000ULL |
| |
| /** |
| * struct ad5758_state - driver instance specific data |
| * @spi: spi_device |
| * @lock: mutex lock |
| * @out_range: struct which stores the output range |
| * @dc_dc_mode: variable which stores the mode of operation |
| * @dc_dc_ilim: variable which stores the dc-to-dc converter current limit |
| * @slew_time: variable which stores the target slew time |
| * @pwr_down: variable which contains whether a channel is powered down or not |
| * @data: spi transfer buffers |
| */ |
| |
| struct ad5758_range { |
| int reg; |
| int min; |
| int max; |
| }; |
| |
| struct ad5758_state { |
| struct spi_device *spi; |
| struct mutex lock; |
| struct gpio_desc *gpio_reset; |
| struct ad5758_range out_range; |
| unsigned int dc_dc_mode; |
| unsigned int dc_dc_ilim; |
| unsigned int slew_time; |
| bool pwr_down; |
| __be32 d32[3]; |
| }; |
| |
| /** |
| * Output ranges corresponding to bits [3:0] from DAC_CONFIG register |
| * 0000: 0 V to 5 V voltage range |
| * 0001: 0 V to 10 V voltage range |
| * 0010: ±5 V voltage range |
| * 0011: ±10 V voltage range |
| * 1000: 0 mA to 20 mA current range |
| * 1001: 0 mA to 24 mA current range |
| * 1010: 4 mA to 20 mA current range |
| * 1011: ±20 mA current range |
| * 1100: ±24 mA current range |
| * 1101: -1 mA to +22 mA current range |
| */ |
| enum ad5758_output_range { |
| AD5758_RANGE_0V_5V, |
| AD5758_RANGE_0V_10V, |
| AD5758_RANGE_PLUSMINUS_5V, |
| AD5758_RANGE_PLUSMINUS_10V, |
| AD5758_RANGE_0mA_20mA = 8, |
| AD5758_RANGE_0mA_24mA, |
| AD5758_RANGE_4mA_24mA, |
| AD5758_RANGE_PLUSMINUS_20mA, |
| AD5758_RANGE_PLUSMINUS_24mA, |
| AD5758_RANGE_MINUS_1mA_PLUS_22mA, |
| }; |
| |
| enum ad5758_dc_dc_mode { |
| AD5758_DCDC_MODE_POWER_OFF, |
| AD5758_DCDC_MODE_DPC_CURRENT, |
| AD5758_DCDC_MODE_DPC_VOLTAGE, |
| AD5758_DCDC_MODE_PPC_CURRENT, |
| }; |
| |
| static const struct ad5758_range ad5758_voltage_range[] = { |
| { AD5758_RANGE_0V_5V, 0, 5000000 }, |
| { AD5758_RANGE_0V_10V, 0, 10000000 }, |
| { AD5758_RANGE_PLUSMINUS_5V, -5000000, 5000000 }, |
| { AD5758_RANGE_PLUSMINUS_10V, -10000000, 10000000 } |
| }; |
| |
| static const struct ad5758_range ad5758_current_range[] = { |
| { AD5758_RANGE_0mA_20mA, 0, 20000}, |
| { AD5758_RANGE_0mA_24mA, 0, 24000 }, |
| { AD5758_RANGE_4mA_24mA, 4, 24000 }, |
| { AD5758_RANGE_PLUSMINUS_20mA, -20000, 20000 }, |
| { AD5758_RANGE_PLUSMINUS_24mA, -24000, 24000 }, |
| { AD5758_RANGE_MINUS_1mA_PLUS_22mA, -1000, 22000 }, |
| }; |
| |
| static const int ad5758_sr_clk[16] = { |
| 240000, 200000, 150000, 128000, 64000, 32000, 16000, 8000, 4000, 2000, |
| 1000, 512, 256, 128, 64, 16 |
| }; |
| |
| static const int ad5758_sr_step[8] = { |
| 4, 12, 64, 120, 256, 500, 1820, 2048 |
| }; |
| |
| static const int ad5758_dc_dc_ilim[6] = { |
| 150000, 200000, 250000, 300000, 350000, 400000 |
| }; |
| |
| static int ad5758_spi_reg_read(struct ad5758_state *st, unsigned int addr) |
| { |
| struct spi_transfer t[] = { |
| { |
| .tx_buf = &st->d32[0], |
| .len = 4, |
| .cs_change = 1, |
| }, { |
| .tx_buf = &st->d32[1], |
| .rx_buf = &st->d32[2], |
| .len = 4, |
| }, |
| }; |
| int ret; |
| |
| st->d32[0] = cpu_to_be32( |
| (AD5758_WR_FLAG_MSK(AD5758_TWO_STAGE_READBACK_SELECT) << 24) | |
| (addr << 8)); |
| st->d32[1] = cpu_to_be32(AD5758_WR_FLAG_MSK(AD5758_NOP) << 24); |
| |
| ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t)); |
| if (ret < 0) |
| return ret; |
| |
| return (be32_to_cpu(st->d32[2]) >> 8) & 0xFFFF; |
| } |
| |
| static int ad5758_spi_reg_write(struct ad5758_state *st, |
| unsigned int addr, |
| unsigned int val) |
| { |
| st->d32[0] = cpu_to_be32((AD5758_WR_FLAG_MSK(addr) << 24) | |
| ((val & 0xFFFF) << 8)); |
| |
| return spi_write(st->spi, &st->d32[0], sizeof(st->d32[0])); |
| } |
| |
| static int ad5758_spi_write_mask(struct ad5758_state *st, |
| unsigned int addr, |
| unsigned long int mask, |
| unsigned int val) |
| { |
| int regval; |
| |
| regval = ad5758_spi_reg_read(st, addr); |
| if (regval < 0) |
| return regval; |
| |
| regval &= ~mask; |
| regval |= val; |
| |
| return ad5758_spi_reg_write(st, addr, regval); |
| } |
| |
| static int cmpfunc(const void *a, const void *b) |
| { |
| return *(int *)a - *(int *)b; |
| } |
| |
| static int ad5758_find_closest_match(const int *array, |
| unsigned int size, int val) |
| { |
| int i; |
| |
| for (i = 0; i < size; i++) { |
| if (val <= array[i]) |
| return i; |
| } |
| |
| return size - 1; |
| } |
| |
| static int ad5758_wait_for_task_complete(struct ad5758_state *st, |
| unsigned int reg, |
| unsigned int mask) |
| { |
| unsigned int timeout; |
| int ret; |
| |
| timeout = 10; |
| do { |
| ret = ad5758_spi_reg_read(st, reg); |
| if (ret < 0) |
| return ret; |
| |
| if (!(ret & mask)) |
| return 0; |
| |
| usleep_range(100, 1000); |
| } while (--timeout); |
| |
| dev_err(&st->spi->dev, |
| "Error reading bit 0x%x in 0x%x register\n", mask, reg); |
| |
| return -EIO; |
| } |
| |
| static int ad5758_calib_mem_refresh(struct ad5758_state *st) |
| { |
| int ret; |
| |
| ret = ad5758_spi_reg_write(st, AD5758_KEY, |
| AD5758_KEY_CODE_CALIB_MEM_REFRESH); |
| if (ret < 0) { |
| dev_err(&st->spi->dev, |
| "Failed to initiate a calibration memory refresh\n"); |
| return ret; |
| } |
| |
| /* Wait to allow time for the internal calibrations to complete */ |
| return ad5758_wait_for_task_complete(st, AD5758_DIGITAL_DIAG_RESULTS, |
| AD5758_CAL_MEM_UNREFRESHED_MSK); |
| } |
| |
| static int ad5758_soft_reset(struct ad5758_state *st) |
| { |
| int ret; |
| |
| ret = ad5758_spi_reg_write(st, AD5758_KEY, AD5758_KEY_CODE_RESET_1); |
| if (ret < 0) |
| return ret; |
| |
| ret = ad5758_spi_reg_write(st, AD5758_KEY, AD5758_KEY_CODE_RESET_2); |
| |
| /* Perform a software reset and wait at least 100us */ |
| usleep_range(100, 1000); |
| |
| return ret; |
| } |
| |
| static int ad5758_set_dc_dc_conv_mode(struct ad5758_state *st, |
| enum ad5758_dc_dc_mode mode) |
| { |
| int ret; |
| |
| /* |
| * The ENABLE_PPC_BUFFERS bit must be set prior to enabling PPC current |
| * mode. |
| */ |
| if (mode == AD5758_DCDC_MODE_PPC_CURRENT) { |
| ret = ad5758_spi_write_mask(st, AD5758_ADC_CONFIG, |
| AD5758_ADC_CONFIG_PPC_BUF_MSK, |
| AD5758_ADC_CONFIG_PPC_BUF_EN(1)); |
| if (ret < 0) |
| return ret; |
| } |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DCDC_CONFIG1, |
| AD5758_DCDC_CONFIG1_DCDC_MODE_MSK, |
| AD5758_DCDC_CONFIG1_DCDC_MODE_MODE(mode)); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Poll the BUSY_3WI bit in the DCDC_CONFIG2 register until it is 0. |
| * This allows the 3-wire interface communication to complete. |
| */ |
| ret = ad5758_wait_for_task_complete(st, AD5758_DCDC_CONFIG2, |
| AD5758_DCDC_CONFIG2_BUSY_3WI_MSK); |
| if (ret < 0) |
| return ret; |
| |
| st->dc_dc_mode = mode; |
| |
| return ret; |
| } |
| |
| static int ad5758_set_dc_dc_ilim(struct ad5758_state *st, unsigned int ilim) |
| { |
| int ret; |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DCDC_CONFIG2, |
| AD5758_DCDC_CONFIG2_ILIMIT_MSK, |
| AD5758_DCDC_CONFIG2_ILIMIT_MODE(ilim)); |
| if (ret < 0) |
| return ret; |
| /* |
| * Poll the BUSY_3WI bit in the DCDC_CONFIG2 register until it is 0. |
| * This allows the 3-wire interface communication to complete. |
| */ |
| return ad5758_wait_for_task_complete(st, AD5758_DCDC_CONFIG2, |
| AD5758_DCDC_CONFIG2_BUSY_3WI_MSK); |
| } |
| |
| static int ad5758_slew_rate_set(struct ad5758_state *st, |
| unsigned int sr_clk_idx, |
| unsigned int sr_step_idx) |
| { |
| unsigned int mode; |
| unsigned long int mask; |
| int ret; |
| |
| mask = AD5758_DAC_CONFIG_SR_EN_MSK | |
| AD5758_DAC_CONFIG_SR_CLOCK_MSK | |
| AD5758_DAC_CONFIG_SR_STEP_MSK; |
| mode = AD5758_DAC_CONFIG_SR_EN_MODE(1) | |
| AD5758_DAC_CONFIG_SR_STEP_MODE(sr_step_idx) | |
| AD5758_DAC_CONFIG_SR_CLOCK_MODE(sr_clk_idx); |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DAC_CONFIG, mask, mode); |
| if (ret < 0) |
| return ret; |
| |
| /* Wait to allow time for the internal calibrations to complete */ |
| return ad5758_wait_for_task_complete(st, AD5758_DIGITAL_DIAG_RESULTS, |
| AD5758_CAL_MEM_UNREFRESHED_MSK); |
| } |
| |
| static int ad5758_slew_rate_config(struct ad5758_state *st) |
| { |
| unsigned int sr_clk_idx, sr_step_idx; |
| int i, res; |
| s64 diff_new, diff_old; |
| u64 sr_step, calc_slew_time; |
| |
| sr_clk_idx = 0; |
| sr_step_idx = 0; |
| diff_old = S64_MAX; |
| /* |
| * The slew time can be determined by using the formula: |
| * Slew Time = (Full Scale Out / (Step Size x Update Clk Freq)) |
| * where Slew time is expressed in microseconds |
| * Given the desired slew time, the following algorithm determines the |
| * best match for the step size and the update clock frequency. |
| */ |
| for (i = 0; i < ARRAY_SIZE(ad5758_sr_clk); i++) { |
| /* |
| * Go through each valid update clock freq and determine a raw |
| * value for the step size by using the formula: |
| * Step Size = Full Scale Out / (Update Clk Freq * Slew Time) |
| */ |
| sr_step = AD5758_FULL_SCALE_MICRO; |
| do_div(sr_step, ad5758_sr_clk[i]); |
| do_div(sr_step, st->slew_time); |
| /* |
| * After a raw value for step size was determined, find the |
| * closest valid match |
| */ |
| res = ad5758_find_closest_match(ad5758_sr_step, |
| ARRAY_SIZE(ad5758_sr_step), |
| sr_step); |
| /* Calculate the slew time */ |
| calc_slew_time = AD5758_FULL_SCALE_MICRO; |
| do_div(calc_slew_time, ad5758_sr_step[res]); |
| do_div(calc_slew_time, ad5758_sr_clk[i]); |
| /* |
| * Determine with how many microseconds the calculated slew time |
| * is different from the desired slew time and store the diff |
| * for the next iteration |
| */ |
| diff_new = abs(st->slew_time - calc_slew_time); |
| if (diff_new < diff_old) { |
| diff_old = diff_new; |
| sr_clk_idx = i; |
| sr_step_idx = res; |
| } |
| } |
| |
| return ad5758_slew_rate_set(st, sr_clk_idx, sr_step_idx); |
| } |
| |
| static int ad5758_set_out_range(struct ad5758_state *st, int range) |
| { |
| int ret; |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DAC_CONFIG, |
| AD5758_DAC_CONFIG_RANGE_MSK, |
| AD5758_DAC_CONFIG_RANGE_MODE(range)); |
| if (ret < 0) |
| return ret; |
| |
| /* Wait to allow time for the internal calibrations to complete */ |
| return ad5758_wait_for_task_complete(st, AD5758_DIGITAL_DIAG_RESULTS, |
| AD5758_CAL_MEM_UNREFRESHED_MSK); |
| } |
| |
| static int ad5758_internal_buffers_en(struct ad5758_state *st, bool enable) |
| { |
| int ret; |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DAC_CONFIG, |
| AD5758_DAC_CONFIG_INT_EN_MSK, |
| AD5758_DAC_CONFIG_INT_EN_MODE(enable)); |
| if (ret < 0) |
| return ret; |
| |
| /* Wait to allow time for the internal calibrations to complete */ |
| return ad5758_wait_for_task_complete(st, AD5758_DIGITAL_DIAG_RESULTS, |
| AD5758_CAL_MEM_UNREFRESHED_MSK); |
| } |
| |
| static int ad5758_reset(struct ad5758_state *st) |
| { |
| if (st->gpio_reset) { |
| gpiod_set_value(st->gpio_reset, 0); |
| usleep_range(100, 1000); |
| gpiod_set_value(st->gpio_reset, 1); |
| usleep_range(100, 1000); |
| |
| return 0; |
| } else { |
| /* Perform a software reset */ |
| return ad5758_soft_reset(st); |
| } |
| } |
| |
| static int ad5758_reg_access(struct iio_dev *indio_dev, |
| unsigned int reg, |
| unsigned int writeval, |
| unsigned int *readval) |
| { |
| struct ad5758_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| mutex_lock(&st->lock); |
| if (readval) { |
| ret = ad5758_spi_reg_read(st, reg); |
| if (ret < 0) { |
| mutex_unlock(&st->lock); |
| return ret; |
| } |
| |
| *readval = ret; |
| ret = 0; |
| } else { |
| ret = ad5758_spi_reg_write(st, reg, writeval); |
| } |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int ad5758_read_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int *val, int *val2, long info) |
| { |
| struct ad5758_state *st = iio_priv(indio_dev); |
| int max, min, ret; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_RAW: |
| mutex_lock(&st->lock); |
| ret = ad5758_spi_reg_read(st, AD5758_DAC_INPUT); |
| mutex_unlock(&st->lock); |
| if (ret < 0) |
| return ret; |
| |
| *val = ret; |
| return IIO_VAL_INT; |
| case IIO_CHAN_INFO_SCALE: |
| min = st->out_range.min; |
| max = st->out_range.max; |
| *val = (max - min) / 1000; |
| *val2 = 16; |
| return IIO_VAL_FRACTIONAL_LOG2; |
| case IIO_CHAN_INFO_OFFSET: |
| min = st->out_range.min; |
| max = st->out_range.max; |
| *val = ((min * (1 << 16)) / (max - min)) / 1000; |
| return IIO_VAL_INT; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad5758_write_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int val, int val2, long info) |
| { |
| struct ad5758_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_RAW: |
| mutex_lock(&st->lock); |
| ret = ad5758_spi_reg_write(st, AD5758_DAC_INPUT, val); |
| mutex_unlock(&st->lock); |
| return ret; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static ssize_t ad5758_read_powerdown(struct iio_dev *indio_dev, |
| uintptr_t priv, |
| const struct iio_chan_spec *chan, |
| char *buf) |
| { |
| struct ad5758_state *st = iio_priv(indio_dev); |
| |
| return sprintf(buf, "%d\n", st->pwr_down); |
| } |
| |
| static ssize_t ad5758_write_powerdown(struct iio_dev *indio_dev, |
| uintptr_t priv, |
| struct iio_chan_spec const *chan, |
| const char *buf, size_t len) |
| { |
| struct ad5758_state *st = iio_priv(indio_dev); |
| bool pwr_down; |
| unsigned int dac_config_mode, val; |
| unsigned long int dac_config_msk; |
| int ret; |
| |
| ret = kstrtobool(buf, &pwr_down); |
| if (ret) |
| return ret; |
| |
| mutex_lock(&st->lock); |
| if (pwr_down) |
| val = 0; |
| else |
| val = 1; |
| |
| dac_config_mode = AD5758_DAC_CONFIG_OUT_EN_MODE(val) | |
| AD5758_DAC_CONFIG_INT_EN_MODE(val); |
| dac_config_msk = AD5758_DAC_CONFIG_OUT_EN_MSK | |
| AD5758_DAC_CONFIG_INT_EN_MSK; |
| |
| ret = ad5758_spi_write_mask(st, AD5758_DAC_CONFIG, |
| dac_config_msk, |
| dac_config_mode); |
| if (ret < 0) |
| goto err_unlock; |
| |
| st->pwr_down = pwr_down; |
| |
| err_unlock: |
| mutex_unlock(&st->lock); |
| |
| return ret ? ret : len; |
| } |
| |
| static const struct iio_info ad5758_info = { |
| .read_raw = ad5758_read_raw, |
| .write_raw = ad5758_write_raw, |
| .debugfs_reg_access = &ad5758_reg_access, |
| }; |
| |
| static const struct iio_chan_spec_ext_info ad5758_ext_info[] = { |
| { |
| .name = "powerdown", |
| .read = ad5758_read_powerdown, |
| .write = ad5758_write_powerdown, |
| .shared = IIO_SHARED_BY_TYPE, |
| }, |
| { } |
| }; |
| |
| #define AD5758_DAC_CHAN(_chan_type) { \ |
| .type = (_chan_type), \ |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_RAW) | \ |
| BIT(IIO_CHAN_INFO_SCALE) | \ |
| BIT(IIO_CHAN_INFO_OFFSET), \ |
| .indexed = 1, \ |
| .output = 1, \ |
| .ext_info = ad5758_ext_info, \ |
| } |
| |
| static const struct iio_chan_spec ad5758_voltage_ch[] = { |
| AD5758_DAC_CHAN(IIO_VOLTAGE) |
| }; |
| |
| static const struct iio_chan_spec ad5758_current_ch[] = { |
| AD5758_DAC_CHAN(IIO_CURRENT) |
| }; |
| |
| static bool ad5758_is_valid_mode(enum ad5758_dc_dc_mode mode) |
| { |
| switch (mode) { |
| case AD5758_DCDC_MODE_DPC_CURRENT: |
| case AD5758_DCDC_MODE_DPC_VOLTAGE: |
| case AD5758_DCDC_MODE_PPC_CURRENT: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static int ad5758_crc_disable(struct ad5758_state *st) |
| { |
| unsigned int mask; |
| |
| mask = (AD5758_WR_FLAG_MSK(AD5758_DIGITAL_DIAG_CONFIG) << 24) | 0x5C3A; |
| st->d32[0] = cpu_to_be32(mask); |
| |
| return spi_write(st->spi, &st->d32[0], 4); |
| } |
| |
| static int ad5758_find_out_range(struct ad5758_state *st, |
| const struct ad5758_range *range, |
| unsigned int size, |
| int min, int max) |
| { |
| int i; |
| |
| for (i = 0; i < size; i++) { |
| if ((min == range[i].min) && (max == range[i].max)) { |
| st->out_range.reg = range[i].reg; |
| st->out_range.min = range[i].min; |
| st->out_range.max = range[i].max; |
| |
| return 0; |
| } |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int ad5758_parse_dt(struct ad5758_state *st) |
| { |
| unsigned int tmp, tmparray[2], size; |
| const struct ad5758_range *range; |
| int *index, ret; |
| |
| st->dc_dc_ilim = 0; |
| ret = device_property_read_u32(&st->spi->dev, |
| "adi,dc-dc-ilim-microamp", &tmp); |
| if (ret) { |
| dev_dbg(&st->spi->dev, |
| "Missing \"dc-dc-ilim-microamp\" property\n"); |
| } else { |
| index = bsearch(&tmp, ad5758_dc_dc_ilim, |
| ARRAY_SIZE(ad5758_dc_dc_ilim), |
| sizeof(int), cmpfunc); |
| if (!index) |
| dev_dbg(&st->spi->dev, "dc-dc-ilim out of range\n"); |
| else |
| st->dc_dc_ilim = index - ad5758_dc_dc_ilim; |
| } |
| |
| ret = device_property_read_u32(&st->spi->dev, "adi,dc-dc-mode", |
| &st->dc_dc_mode); |
| if (ret) { |
| dev_err(&st->spi->dev, "Missing \"dc-dc-mode\" property\n"); |
| return ret; |
| } |
| |
| if (!ad5758_is_valid_mode(st->dc_dc_mode)) |
| return -EINVAL; |
| |
| if (st->dc_dc_mode == AD5758_DCDC_MODE_DPC_VOLTAGE) { |
| ret = device_property_read_u32_array(&st->spi->dev, |
| "adi,range-microvolt", |
| tmparray, 2); |
| if (ret) { |
| dev_err(&st->spi->dev, |
| "Missing \"range-microvolt\" property\n"); |
| return ret; |
| } |
| range = ad5758_voltage_range; |
| size = ARRAY_SIZE(ad5758_voltage_range); |
| } else { |
| ret = device_property_read_u32_array(&st->spi->dev, |
| "adi,range-microamp", |
| tmparray, 2); |
| if (ret) { |
| dev_err(&st->spi->dev, |
| "Missing \"range-microamp\" property\n"); |
| return ret; |
| } |
| range = ad5758_current_range; |
| size = ARRAY_SIZE(ad5758_current_range); |
| } |
| |
| ret = ad5758_find_out_range(st, range, size, tmparray[0], tmparray[1]); |
| if (ret) { |
| dev_err(&st->spi->dev, "range invalid\n"); |
| return ret; |
| } |
| |
| ret = device_property_read_u32(&st->spi->dev, "adi,slew-time-us", &tmp); |
| if (ret) { |
| dev_dbg(&st->spi->dev, "Missing \"slew-time-us\" property\n"); |
| st->slew_time = 0; |
| } else { |
| st->slew_time = tmp; |
| } |
| |
| return 0; |
| } |
| |
| static int ad5758_init(struct ad5758_state *st) |
| { |
| int regval, ret; |
| |
| st->gpio_reset = devm_gpiod_get_optional(&st->spi->dev, "reset", |
| GPIOD_OUT_HIGH); |
| if (IS_ERR(st->gpio_reset)) |
| return PTR_ERR(st->gpio_reset); |
| |
| /* Disable CRC checks */ |
| ret = ad5758_crc_disable(st); |
| if (ret < 0) |
| return ret; |
| |
| /* Perform a reset */ |
| ret = ad5758_reset(st); |
| if (ret < 0) |
| return ret; |
| |
| /* Disable CRC checks */ |
| ret = ad5758_crc_disable(st); |
| if (ret < 0) |
| return ret; |
| |
| /* Perform a calibration memory refresh */ |
| ret = ad5758_calib_mem_refresh(st); |
| if (ret < 0) |
| return ret; |
| |
| regval = ad5758_spi_reg_read(st, AD5758_DIGITAL_DIAG_RESULTS); |
| if (regval < 0) |
| return regval; |
| |
| /* Clear all the error flags */ |
| ret = ad5758_spi_reg_write(st, AD5758_DIGITAL_DIAG_RESULTS, regval); |
| if (ret < 0) |
| return ret; |
| |
| /* Set the dc-to-dc current limit */ |
| ret = ad5758_set_dc_dc_ilim(st, st->dc_dc_ilim); |
| if (ret < 0) |
| return ret; |
| |
| /* Configure the dc-to-dc controller mode */ |
| ret = ad5758_set_dc_dc_conv_mode(st, st->dc_dc_mode); |
| if (ret < 0) |
| return ret; |
| |
| /* Configure the output range */ |
| ret = ad5758_set_out_range(st, st->out_range.reg); |
| if (ret < 0) |
| return ret; |
| |
| /* Enable Slew Rate Control, set the slew rate clock and step */ |
| if (st->slew_time) { |
| ret = ad5758_slew_rate_config(st); |
| if (ret < 0) |
| return ret; |
| } |
| |
| /* Power up the DAC and internal (INT) amplifiers */ |
| ret = ad5758_internal_buffers_en(st, 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Enable VIOUT */ |
| return ad5758_spi_write_mask(st, AD5758_DAC_CONFIG, |
| AD5758_DAC_CONFIG_OUT_EN_MSK, |
| AD5758_DAC_CONFIG_OUT_EN_MODE(1)); |
| } |
| |
| static int ad5758_probe(struct spi_device *spi) |
| { |
| struct ad5758_state *st; |
| struct iio_dev *indio_dev; |
| int ret; |
| |
| indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); |
| if (!indio_dev) |
| return -ENOMEM; |
| |
| st = iio_priv(indio_dev); |
| spi_set_drvdata(spi, indio_dev); |
| |
| st->spi = spi; |
| |
| mutex_init(&st->lock); |
| |
| indio_dev->dev.parent = &spi->dev; |
| indio_dev->name = spi_get_device_id(spi)->name; |
| indio_dev->info = &ad5758_info; |
| indio_dev->modes = INDIO_DIRECT_MODE; |
| indio_dev->num_channels = 1; |
| |
| ret = ad5758_parse_dt(st); |
| if (ret < 0) |
| return ret; |
| |
| if (st->dc_dc_mode == AD5758_DCDC_MODE_DPC_VOLTAGE) |
| indio_dev->channels = ad5758_voltage_ch; |
| else |
| indio_dev->channels = ad5758_current_ch; |
| |
| ret = ad5758_init(st); |
| if (ret < 0) { |
| dev_err(&spi->dev, "AD5758 init failed\n"); |
| return ret; |
| } |
| |
| return devm_iio_device_register(&st->spi->dev, indio_dev); |
| } |
| |
| static const struct spi_device_id ad5758_id[] = { |
| { "ad5758", 0 }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(spi, ad5758_id); |
| |
| static const struct of_device_id ad5758_of_match[] = { |
| { .compatible = "adi,ad5758" }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, ad5758_of_match); |
| |
| static struct spi_driver ad5758_driver = { |
| .driver = { |
| .name = KBUILD_MODNAME, |
| .of_match_table = ad5758_of_match, |
| }, |
| .probe = ad5758_probe, |
| .id_table = ad5758_id, |
| }; |
| |
| module_spi_driver(ad5758_driver); |
| |
| MODULE_AUTHOR("Stefan Popa <stefan.popa@analog.com>"); |
| MODULE_DESCRIPTION("Analog Devices AD5758 DAC"); |
| MODULE_LICENSE("GPL v2"); |