| // SPDX-License-Identifier: GPL-2.0-only OR MIT |
| /* |
| * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/ |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| |
| #include "k3-j7200.dtsi" |
| |
| / { |
| memory@80000000 { |
| device_type = "memory"; |
| /* 4G RAM */ |
| reg = <0x00 0x80000000 0x00 0x80000000>, |
| <0x08 0x80000000 0x00 0x80000000>; |
| }; |
| |
| reserved_memory: reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| secure_ddr: optee@9e800000 { |
| reg = <0x00 0x9e800000 0x00 0x01800000>; |
| alignment = <0x1000>; |
| no-map; |
| }; |
| |
| mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa0000000 0x00 0x100000>; |
| no-map; |
| }; |
| |
| mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa0100000 0x00 0xf00000>; |
| no-map; |
| }; |
| |
| mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa1000000 0x00 0x100000>; |
| no-map; |
| }; |
| |
| mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa1100000 0x00 0xf00000>; |
| no-map; |
| }; |
| |
| main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa2000000 0x00 0x100000>; |
| no-map; |
| }; |
| |
| main_r5fss0_core0_memory_region: r5f-memory@a2100000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa2100000 0x00 0xf00000>; |
| no-map; |
| }; |
| |
| main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa3000000 0x00 0x100000>; |
| no-map; |
| }; |
| |
| main_r5fss0_core1_memory_region: r5f-memory@a3100000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x00 0xa3100000 0x00 0xf00000>; |
| no-map; |
| }; |
| |
| rtos_ipc_memory_region: ipc-memories@a4000000 { |
| reg = <0x00 0xa4000000 0x00 0x00800000>; |
| alignment = <0x1000>; |
| no-map; |
| }; |
| }; |
| |
| mux0: mux-controller { |
| compatible = "gpio-mux"; |
| #mux-state-cells = <1>; |
| mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| mux1: mux-controller { |
| compatible = "gpio-mux"; |
| #mux-state-cells = <1>; |
| mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| transceiver0: can-phy0 { |
| /* standby pin has been grounded by default */ |
| compatible = "ti,tcan1042"; |
| #phy-cells = <0>; |
| max-bitrate = <5000000>; |
| }; |
| }; |
| |
| &wkup_pmx0 { |
| mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (B6) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */ |
| J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C8) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */ |
| J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (D6) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */ |
| J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (D7) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */ |
| J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (B7) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */ |
| J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D8) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */ |
| J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (C7) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */ |
| J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (C5) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */ |
| J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (A5) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */ |
| J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (A6) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */ |
| J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */ |
| J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */ |
| J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ |
| >; |
| }; |
| |
| mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */ |
| J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */ |
| J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */ |
| J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */ |
| J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */ |
| J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */ |
| J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */ |
| J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */ |
| J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */ |
| J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */ |
| J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */ |
| >; |
| }; |
| }; |
| |
| &wkup_pmx2 { |
| wkup_i2c0_pins_default: wkup-i2c0-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */ |
| J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */ |
| >; |
| }; |
| }; |
| |
| &wkup_pmx3 { |
| pmic_irq_pins_default: pmic-irq-default-pins { |
| pinctrl-single,pins = < |
| J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */ |
| >; |
| }; |
| }; |
| |
| &main_pmx0 { |
| main_i2c0_pins_default: main-i2c0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ |
| J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ |
| >; |
| }; |
| |
| main_mcan0_pins_default: main-mcan0-default-pins { |
| pinctrl-single,pins = < |
| J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */ |
| J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */ |
| >; |
| }; |
| }; |
| |
| &hbmc { |
| /* OSPI and HBMC are muxed inside FSS, Bootloader will enable |
| * appropriate node based on board detection |
| */ |
| status = "disabled"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_fss0_hpb0_pins_default>; |
| ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */ |
| <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */ |
| |
| flash@0,0 { |
| compatible = "cypress,hyperflash", "cfi-flash"; |
| reg = <0x00 0x00 0x4000000>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "hbmc.tiboot3"; |
| reg = <0x0 0x100000>; |
| }; |
| |
| partition@100000 { |
| label = "hbmc.tispl"; |
| reg = <0x100000 0x200000>; |
| }; |
| |
| partition@300000 { |
| label = "hbmc.u-boot"; |
| reg = <0x300000 0x400000>; |
| }; |
| |
| partition@700000 { |
| label = "hbmc.env"; |
| reg = <0x700000 0x40000>; |
| }; |
| |
| partition@800000 { |
| label = "hbmc.rootfs"; |
| reg = <0x800000 0x3800000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mailbox0_cluster0 { |
| status = "okay"; |
| interrupts = <436>; |
| |
| mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 { |
| ti,mbox-rx = <0 0 0>; |
| ti,mbox-tx = <1 0 0>; |
| }; |
| |
| mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 { |
| ti,mbox-rx = <2 0 0>; |
| ti,mbox-tx = <3 0 0>; |
| }; |
| }; |
| |
| &mailbox0_cluster1 { |
| status = "okay"; |
| interrupts = <432>; |
| |
| mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { |
| ti,mbox-rx = <0 0 0>; |
| ti,mbox-tx = <1 0 0>; |
| }; |
| |
| mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { |
| ti,mbox-rx = <2 0 0>; |
| ti,mbox-tx = <3 0 0>; |
| }; |
| }; |
| |
| &mcu_r5fss0_core0 { |
| mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; |
| memory-region = <&mcu_r5fss0_core0_dma_memory_region>, |
| <&mcu_r5fss0_core0_memory_region>; |
| }; |
| |
| &mcu_r5fss0_core1 { |
| mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; |
| memory-region = <&mcu_r5fss0_core1_dma_memory_region>, |
| <&mcu_r5fss0_core1_memory_region>; |
| }; |
| |
| &main_r5fss0_core0 { |
| mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; |
| memory-region = <&main_r5fss0_core0_dma_memory_region>, |
| <&main_r5fss0_core0_memory_region>; |
| }; |
| |
| &main_r5fss0_core1 { |
| mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; |
| memory-region = <&main_r5fss0_core1_dma_memory_region>, |
| <&main_r5fss0_core1_memory_region>; |
| }; |
| |
| &main_i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&main_i2c0_pins_default>; |
| clock-frequency = <400000>; |
| |
| exp_som: gpio@21 { |
| compatible = "ti,tca6408"; |
| reg = <0x21>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0", |
| "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1", |
| "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL", |
| "GPIO_LIN_EN", "CAN_STB"; |
| }; |
| }; |
| |
| &wkup_i2c0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wkup_i2c0_pins_default>; |
| clock-frequency = <400000>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c256"; |
| reg = <0x50>; |
| }; |
| |
| tps659414: pmic@48 { |
| compatible = "ti,tps6594-q1"; |
| reg = <0x48>; |
| system-power-controller; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_irq_pins_default>; |
| interrupt-parent = <&wkup_gpio0>; |
| interrupts = <84 IRQ_TYPE_EDGE_FALLING>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| ti,primary-pmic; |
| buck1-supply = <&vsys_3v3>; |
| buck2-supply = <&vsys_3v3>; |
| buck3-supply = <&vsys_3v3>; |
| buck4-supply = <&vsys_3v3>; |
| buck5-supply = <&vsys_3v3>; |
| ldo1-supply = <&vsys_3v3>; |
| ldo2-supply = <&vsys_3v3>; |
| ldo3-supply = <&vsys_3v3>; |
| ldo4-supply = <&vsys_3v3>; |
| |
| regulators { |
| bucka1: buck1 { |
| regulator-name = "vda_mcu_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| bucka2: buck2 { |
| regulator-name = "vdd_mcuio_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| bucka3: buck3 { |
| regulator-name = "vdd_mcu_0v85"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| bucka4: buck4 { |
| regulator-name = "vdd_ddr_1v1"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| bucka5: buck5 { |
| regulator-name = "vdd_phyio_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldoa1: ldo1 { |
| regulator-name = "vdd1_lpddr4_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldoa2: ldo2 { |
| regulator-name = "vda_dll_0v8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldoa3: ldo3 { |
| regulator-name = "vdd_wk_0v8"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldoa4: ldo4 { |
| regulator-name = "vda_pll_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| lp876441: pmic@4c { |
| compatible = "ti,lp8764-q1"; |
| reg = <0x4c>; |
| system-power-controller; |
| interrupt-parent = <&wkup_gpio0>; |
| interrupts = <84 IRQ_TYPE_EDGE_FALLING>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| buck1-supply = <&vsys_3v3>; |
| buck2-supply = <&vsys_3v3>; |
| buck3-supply = <&vsys_3v3>; |
| buck4-supply = <&vsys_3v3>; |
| |
| regulators: regulators { |
| buckb1: buck1 { |
| regulator-name = "vdd_cpu_avs"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <900000>; |
| regulator-always-on; |
| regulator-boot-on; |
| bootph-pre-ram; |
| }; |
| |
| buckb2: buck2 { |
| regulator-name = "vdd_ram_0v85"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buckb3: buck3 { |
| regulator-name = "vdd_core_0v85"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buckb4: buck4 { |
| regulator-name = "vdd_io_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &ospi0 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0x0>; |
| spi-tx-bus-width = <8>; |
| spi-rx-bus-width = <8>; |
| spi-max-frequency = <25000000>; |
| cdns,tshsl-ns = <60>; |
| cdns,tsd2d-ns = <60>; |
| cdns,tchsh-ns = <60>; |
| cdns,tslch-ns = <60>; |
| cdns,read-delay = <4>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "ospi.tiboot3"; |
| reg = <0x0 0x100000>; |
| }; |
| |
| partition@100000 { |
| label = "ospi.tispl"; |
| reg = <0x100000 0x200000>; |
| }; |
| |
| partition@300000 { |
| label = "ospi.u-boot"; |
| reg = <0x300000 0x400000>; |
| }; |
| |
| partition@700000 { |
| label = "ospi.env"; |
| reg = <0x700000 0x40000>; |
| }; |
| |
| partition@740000 { |
| label = "ospi.env.backup"; |
| reg = <0x740000 0x40000>; |
| }; |
| |
| partition@800000 { |
| label = "ospi.rootfs"; |
| reg = <0x800000 0x37c0000>; |
| }; |
| |
| partition@3fc0000 { |
| label = "ospi.phypattern"; |
| reg = <0x3fc0000 0x40000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &main_mcan0 { |
| status = "okay"; |
| pinctrl-0 = <&main_mcan0_pins_default>; |
| pinctrl-names = "default"; |
| phys = <&transceiver0>; |
| }; |
