| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * ADMV1013 driver |
| * |
| * Copyright 2021 Analog Devices Inc. |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/device.h> |
| #include <linux/iio/iio.h> |
| #include <linux/module.h> |
| #include <linux/mod_devicetable.h> |
| #include <linux/notifier.h> |
| #include <linux/property.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/spi/spi.h> |
| #include <linux/units.h> |
| |
| #include <asm/unaligned.h> |
| |
| /* ADMV1013 Register Map */ |
| #define ADMV1013_REG_SPI_CONTROL 0x00 |
| #define ADMV1013_REG_ALARM 0x01 |
| #define ADMV1013_REG_ALARM_MASKS 0x02 |
| #define ADMV1013_REG_ENABLE 0x03 |
| #define ADMV1013_REG_LO_AMP_I 0x05 |
| #define ADMV1013_REG_LO_AMP_Q 0x06 |
| #define ADMV1013_REG_OFFSET_ADJUST_I 0x07 |
| #define ADMV1013_REG_OFFSET_ADJUST_Q 0x08 |
| #define ADMV1013_REG_QUAD 0x09 |
| #define ADMV1013_REG_VVA_TEMP_COMP 0x0A |
| |
| /* ADMV1013_REG_SPI_CONTROL Map */ |
| #define ADMV1013_PARITY_EN_MSK BIT(15) |
| #define ADMV1013_SPI_SOFT_RESET_MSK BIT(14) |
| #define ADMV1013_CHIP_ID_MSK GENMASK(11, 4) |
| #define ADMV1013_CHIP_ID 0xA |
| #define ADMV1013_REVISION_ID_MSK GENMASK(3, 0) |
| |
| /* ADMV1013_REG_ALARM Map */ |
| #define ADMV1013_PARITY_ERROR_MSK BIT(15) |
| #define ADMV1013_TOO_FEW_ERRORS_MSK BIT(14) |
| #define ADMV1013_TOO_MANY_ERRORS_MSK BIT(13) |
| #define ADMV1013_ADDRESS_RANGE_ERROR_MSK BIT(12) |
| |
| /* ADMV1013_REG_ENABLE Map */ |
| #define ADMV1013_VGA_PD_MSK BIT(15) |
| #define ADMV1013_MIXER_PD_MSK BIT(14) |
| #define ADMV1013_QUAD_PD_MSK GENMASK(13, 11) |
| #define ADMV1013_BG_PD_MSK BIT(10) |
| #define ADMV1013_MIXER_IF_EN_MSK BIT(7) |
| #define ADMV1013_DET_EN_MSK BIT(5) |
| |
| /* ADMV1013_REG_LO_AMP Map */ |
| #define ADMV1013_LOAMP_PH_ADJ_FINE_MSK GENMASK(13, 7) |
| #define ADMV1013_MIXER_VGATE_MSK GENMASK(6, 0) |
| |
| /* ADMV1013_REG_OFFSET_ADJUST Map */ |
| #define ADMV1013_MIXER_OFF_ADJ_P_MSK GENMASK(15, 9) |
| #define ADMV1013_MIXER_OFF_ADJ_N_MSK GENMASK(8, 2) |
| |
| /* ADMV1013_REG_QUAD Map */ |
| #define ADMV1013_QUAD_SE_MODE_MSK GENMASK(9, 6) |
| #define ADMV1013_QUAD_FILTERS_MSK GENMASK(3, 0) |
| |
| /* ADMV1013_REG_VVA_TEMP_COMP Map */ |
| #define ADMV1013_VVA_TEMP_COMP_MSK GENMASK(15, 0) |
| |
| /* ADMV1013 Miscellaneous Defines */ |
| #define ADMV1013_READ BIT(7) |
| #define ADMV1013_REG_ADDR_READ_MSK GENMASK(6, 1) |
| #define ADMV1013_REG_ADDR_WRITE_MSK GENMASK(22, 17) |
| #define ADMV1013_REG_DATA_MSK GENMASK(16, 1) |
| |
| enum { |
| ADMV1013_IQ_MODE, |
| ADMV1013_IF_MODE |
| }; |
| |
| enum { |
| ADMV1013_RFMOD_I_CALIBPHASE, |
| ADMV1013_RFMOD_Q_CALIBPHASE, |
| }; |
| |
| enum { |
| ADMV1013_SE_MODE_POS = 6, |
| ADMV1013_SE_MODE_NEG = 9, |
| ADMV1013_SE_MODE_DIFF = 12 |
| }; |
| |
| struct admv1013_state { |
| struct spi_device *spi; |
| struct clk *clkin; |
| /* Protect against concurrent accesses to the device and to data */ |
| struct mutex lock; |
| struct regulator *reg; |
| struct notifier_block nb; |
| unsigned int input_mode; |
| unsigned int quad_se_mode; |
| bool det_en; |
| u8 data[3] __aligned(IIO_DMA_MINALIGN); |
| }; |
| |
| static int __admv1013_spi_read(struct admv1013_state *st, unsigned int reg, |
| unsigned int *val) |
| { |
| int ret; |
| struct spi_transfer t = {0}; |
| |
| st->data[0] = ADMV1013_READ | FIELD_PREP(ADMV1013_REG_ADDR_READ_MSK, reg); |
| st->data[1] = 0x0; |
| st->data[2] = 0x0; |
| |
| t.rx_buf = &st->data[0]; |
| t.tx_buf = &st->data[0]; |
| t.len = 3; |
| |
| ret = spi_sync_transfer(st->spi, &t, 1); |
| if (ret) |
| return ret; |
| |
| *val = FIELD_GET(ADMV1013_REG_DATA_MSK, get_unaligned_be24(&st->data[0])); |
| |
| return ret; |
| } |
| |
| static int admv1013_spi_read(struct admv1013_state *st, unsigned int reg, |
| unsigned int *val) |
| { |
| int ret; |
| |
| mutex_lock(&st->lock); |
| ret = __admv1013_spi_read(st, reg, val); |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int __admv1013_spi_write(struct admv1013_state *st, |
| unsigned int reg, |
| unsigned int val) |
| { |
| put_unaligned_be24(FIELD_PREP(ADMV1013_REG_DATA_MSK, val) | |
| FIELD_PREP(ADMV1013_REG_ADDR_WRITE_MSK, reg), &st->data[0]); |
| |
| return spi_write(st->spi, &st->data[0], 3); |
| } |
| |
| static int admv1013_spi_write(struct admv1013_state *st, unsigned int reg, |
| unsigned int val) |
| { |
| int ret; |
| |
| mutex_lock(&st->lock); |
| ret = __admv1013_spi_write(st, reg, val); |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int __admv1013_spi_update_bits(struct admv1013_state *st, unsigned int reg, |
| unsigned int mask, unsigned int val) |
| { |
| int ret; |
| unsigned int data, temp; |
| |
| ret = __admv1013_spi_read(st, reg, &data); |
| if (ret) |
| return ret; |
| |
| temp = (data & ~mask) | (val & mask); |
| |
| return __admv1013_spi_write(st, reg, temp); |
| } |
| |
| static int admv1013_spi_update_bits(struct admv1013_state *st, unsigned int reg, |
| unsigned int mask, unsigned int val) |
| { |
| int ret; |
| |
| mutex_lock(&st->lock); |
| ret = __admv1013_spi_update_bits(st, reg, mask, val); |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int admv1013_read_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int *val, int *val2, long info) |
| { |
| struct admv1013_state *st = iio_priv(indio_dev); |
| unsigned int data, addr; |
| int ret; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_CALIBBIAS: |
| switch (chan->channel) { |
| case IIO_MOD_I: |
| addr = ADMV1013_REG_OFFSET_ADJUST_I; |
| break; |
| case IIO_MOD_Q: |
| addr = ADMV1013_REG_OFFSET_ADJUST_Q; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| ret = admv1013_spi_read(st, addr, &data); |
| if (ret) |
| return ret; |
| |
| if (!chan->channel) |
| *val = FIELD_GET(ADMV1013_MIXER_OFF_ADJ_P_MSK, data); |
| else |
| *val = FIELD_GET(ADMV1013_MIXER_OFF_ADJ_N_MSK, data); |
| |
| return IIO_VAL_INT; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int admv1013_write_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int val, int val2, long info) |
| { |
| struct admv1013_state *st = iio_priv(indio_dev); |
| unsigned int addr, data, msk; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_CALIBBIAS: |
| switch (chan->channel2) { |
| case IIO_MOD_I: |
| addr = ADMV1013_REG_OFFSET_ADJUST_I; |
| break; |
| case IIO_MOD_Q: |
| addr = ADMV1013_REG_OFFSET_ADJUST_Q; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (!chan->channel) { |
| msk = ADMV1013_MIXER_OFF_ADJ_P_MSK; |
| data = FIELD_PREP(ADMV1013_MIXER_OFF_ADJ_P_MSK, val); |
| } else { |
| msk = ADMV1013_MIXER_OFF_ADJ_N_MSK; |
| data = FIELD_PREP(ADMV1013_MIXER_OFF_ADJ_N_MSK, val); |
| } |
| |
| return admv1013_spi_update_bits(st, addr, msk, data); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static ssize_t admv1013_read(struct iio_dev *indio_dev, |
| uintptr_t private, |
| const struct iio_chan_spec *chan, |
| char *buf) |
| { |
| struct admv1013_state *st = iio_priv(indio_dev); |
| unsigned int data, addr; |
| int ret; |
| |
| switch ((u32)private) { |
| case ADMV1013_RFMOD_I_CALIBPHASE: |
| addr = ADMV1013_REG_LO_AMP_I; |
| break; |
| case ADMV1013_RFMOD_Q_CALIBPHASE: |
| addr = ADMV1013_REG_LO_AMP_Q; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| ret = admv1013_spi_read(st, addr, &data); |
| if (ret) |
| return ret; |
| |
| data = FIELD_GET(ADMV1013_LOAMP_PH_ADJ_FINE_MSK, data); |
| |
| return sysfs_emit(buf, "%u\n", data); |
| } |
| |
| static ssize_t admv1013_write(struct iio_dev *indio_dev, |
| uintptr_t private, |
| const struct iio_chan_spec *chan, |
| const char *buf, size_t len) |
| { |
| struct admv1013_state *st = iio_priv(indio_dev); |
| unsigned int data; |
| int ret; |
| |
| ret = kstrtou32(buf, 10, &data); |
| if (ret) |
| return ret; |
| |
| data = FIELD_PREP(ADMV1013_LOAMP_PH_ADJ_FINE_MSK, data); |
| |
| switch ((u32)private) { |
| case ADMV1013_RFMOD_I_CALIBPHASE: |
| ret = admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_I, |
| ADMV1013_LOAMP_PH_ADJ_FINE_MSK, |
| data); |
| if (ret) |
| return ret; |
| break; |
| case ADMV1013_RFMOD_Q_CALIBPHASE: |
| ret = admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_Q, |
| ADMV1013_LOAMP_PH_ADJ_FINE_MSK, |
| data); |
| if (ret) |
| return ret; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return ret ? ret : len; |
| } |
| |
| static int admv1013_update_quad_filters(struct admv1013_state *st) |
| { |
| unsigned int filt_raw; |
| u64 rate = clk_get_rate(st->clkin); |
| |
| if (rate >= (5400 * HZ_PER_MHZ) && rate <= (7000 * HZ_PER_MHZ)) |
| filt_raw = 15; |
| else if (rate >= (5400 * HZ_PER_MHZ) && rate <= (8000 * HZ_PER_MHZ)) |
| filt_raw = 10; |
| else if (rate >= (6600 * HZ_PER_MHZ) && rate <= (9200 * HZ_PER_MHZ)) |
| filt_raw = 5; |
| else |
| filt_raw = 0; |
| |
| return __admv1013_spi_update_bits(st, ADMV1013_REG_QUAD, |
| ADMV1013_QUAD_FILTERS_MSK, |
| FIELD_PREP(ADMV1013_QUAD_FILTERS_MSK, filt_raw)); |
| } |
| |
| static int admv1013_update_mixer_vgate(struct admv1013_state *st) |
| { |
| unsigned int mixer_vgate; |
| int vcm; |
| |
| vcm = regulator_get_voltage(st->reg); |
| if (vcm < 0) |
| return vcm; |
| |
| if (vcm <= 1800000) |
| mixer_vgate = (2389 * vcm / 1000000 + 8100) / 100; |
| else if (vcm > 1800000 && vcm <= 2600000) |
| mixer_vgate = (2375 * vcm / 1000000 + 125) / 100; |
| else |
| return -EINVAL; |
| |
| return __admv1013_spi_update_bits(st, ADMV1013_REG_LO_AMP_I, |
| ADMV1013_MIXER_VGATE_MSK, |
| FIELD_PREP(ADMV1013_MIXER_VGATE_MSK, mixer_vgate)); |
| } |
| |
| static int admv1013_reg_access(struct iio_dev *indio_dev, |
| unsigned int reg, |
| unsigned int write_val, |
| unsigned int *read_val) |
| { |
| struct admv1013_state *st = iio_priv(indio_dev); |
| |
| if (read_val) |
| return admv1013_spi_read(st, reg, read_val); |
| else |
| return admv1013_spi_write(st, reg, write_val); |
| } |
| |
| static const struct iio_info admv1013_info = { |
| .read_raw = admv1013_read_raw, |
| .write_raw = admv1013_write_raw, |
| .debugfs_reg_access = &admv1013_reg_access, |
| }; |
| |
| static const char * const admv1013_vcc_regs[] = { |
| "vcc-drv", "vcc2-drv", "vcc-vva", "vcc-amp1", "vcc-amp2", |
| "vcc-env", "vcc-bg", "vcc-bg2", "vcc-mixer", "vcc-quad" |
| }; |
| |
| static int admv1013_freq_change(struct notifier_block *nb, unsigned long action, void *data) |
| { |
| struct admv1013_state *st = container_of(nb, struct admv1013_state, nb); |
| int ret; |
| |
| if (action == POST_RATE_CHANGE) { |
| mutex_lock(&st->lock); |
| ret = notifier_from_errno(admv1013_update_quad_filters(st)); |
| mutex_unlock(&st->lock); |
| return ret; |
| } |
| |
| return NOTIFY_OK; |
| } |
| |
| #define _ADMV1013_EXT_INFO(_name, _shared, _ident) { \ |
| .name = _name, \ |
| .read = admv1013_read, \ |
| .write = admv1013_write, \ |
| .private = _ident, \ |
| .shared = _shared, \ |
| } |
| |
| static const struct iio_chan_spec_ext_info admv1013_ext_info[] = { |
| _ADMV1013_EXT_INFO("i_calibphase", IIO_SEPARATE, ADMV1013_RFMOD_I_CALIBPHASE), |
| _ADMV1013_EXT_INFO("q_calibphase", IIO_SEPARATE, ADMV1013_RFMOD_Q_CALIBPHASE), |
| { }, |
| }; |
| |
| #define ADMV1013_CHAN_PHASE(_channel, _channel2, _admv1013_ext_info) { \ |
| .type = IIO_ALTVOLTAGE, \ |
| .output = 0, \ |
| .indexed = 1, \ |
| .channel2 = _channel2, \ |
| .channel = _channel, \ |
| .differential = 1, \ |
| .ext_info = _admv1013_ext_info, \ |
| } |
| |
| #define ADMV1013_CHAN_CALIB(_channel, rf_comp) { \ |
| .type = IIO_ALTVOLTAGE, \ |
| .output = 0, \ |
| .indexed = 1, \ |
| .channel = _channel, \ |
| .channel2 = IIO_MOD_##rf_comp, \ |
| .info_mask_separate = BIT(IIO_CHAN_INFO_CALIBBIAS), \ |
| } |
| |
| static const struct iio_chan_spec admv1013_channels[] = { |
| ADMV1013_CHAN_PHASE(0, 1, admv1013_ext_info), |
| ADMV1013_CHAN_CALIB(0, I), |
| ADMV1013_CHAN_CALIB(0, Q), |
| ADMV1013_CHAN_CALIB(1, I), |
| ADMV1013_CHAN_CALIB(1, Q), |
| }; |
| |
| static int admv1013_init(struct admv1013_state *st) |
| { |
| int ret; |
| unsigned int data; |
| struct spi_device *spi = st->spi; |
| |
| /* Perform a software reset */ |
| ret = __admv1013_spi_update_bits(st, ADMV1013_REG_SPI_CONTROL, |
| ADMV1013_SPI_SOFT_RESET_MSK, |
| FIELD_PREP(ADMV1013_SPI_SOFT_RESET_MSK, 1)); |
| if (ret) |
| return ret; |
| |
| ret = __admv1013_spi_update_bits(st, ADMV1013_REG_SPI_CONTROL, |
| ADMV1013_SPI_SOFT_RESET_MSK, |
| FIELD_PREP(ADMV1013_SPI_SOFT_RESET_MSK, 0)); |
| if (ret) |
| return ret; |
| |
| ret = __admv1013_spi_read(st, ADMV1013_REG_SPI_CONTROL, &data); |
| if (ret) |
| return ret; |
| |
| data = FIELD_GET(ADMV1013_CHIP_ID_MSK, data); |
| if (data != ADMV1013_CHIP_ID) { |
| dev_err(&spi->dev, "Invalid Chip ID.\n"); |
| return -EINVAL; |
| } |
| |
| ret = __admv1013_spi_write(st, ADMV1013_REG_VVA_TEMP_COMP, 0xE700); |
| if (ret) |
| return ret; |
| |
| data = FIELD_PREP(ADMV1013_QUAD_SE_MODE_MSK, st->quad_se_mode); |
| |
| ret = __admv1013_spi_update_bits(st, ADMV1013_REG_QUAD, |
| ADMV1013_QUAD_SE_MODE_MSK, data); |
| if (ret) |
| return ret; |
| |
| ret = admv1013_update_mixer_vgate(st); |
| if (ret) |
| return ret; |
| |
| ret = admv1013_update_quad_filters(st); |
| if (ret) |
| return ret; |
| |
| return __admv1013_spi_update_bits(st, ADMV1013_REG_ENABLE, |
| ADMV1013_DET_EN_MSK | |
| ADMV1013_MIXER_IF_EN_MSK, |
| st->det_en | |
| st->input_mode); |
| } |
| |
| static void admv1013_reg_disable(void *data) |
| { |
| regulator_disable(data); |
| } |
| |
| static void admv1013_powerdown(void *data) |
| { |
| unsigned int enable_reg, enable_reg_msk; |
| |
| /* Disable all components in the Enable Register */ |
| enable_reg_msk = ADMV1013_VGA_PD_MSK | |
| ADMV1013_MIXER_PD_MSK | |
| ADMV1013_QUAD_PD_MSK | |
| ADMV1013_BG_PD_MSK | |
| ADMV1013_MIXER_IF_EN_MSK | |
| ADMV1013_DET_EN_MSK; |
| |
| enable_reg = FIELD_PREP(ADMV1013_VGA_PD_MSK, 1) | |
| FIELD_PREP(ADMV1013_MIXER_PD_MSK, 1) | |
| FIELD_PREP(ADMV1013_QUAD_PD_MSK, 7) | |
| FIELD_PREP(ADMV1013_BG_PD_MSK, 1) | |
| FIELD_PREP(ADMV1013_MIXER_IF_EN_MSK, 0) | |
| FIELD_PREP(ADMV1013_DET_EN_MSK, 0); |
| |
| admv1013_spi_update_bits(data, ADMV1013_REG_ENABLE, enable_reg_msk, enable_reg); |
| } |
| |
| static int admv1013_properties_parse(struct admv1013_state *st) |
| { |
| int ret; |
| const char *str; |
| struct spi_device *spi = st->spi; |
| |
| st->det_en = device_property_read_bool(&spi->dev, "adi,detector-enable"); |
| |
| ret = device_property_read_string(&spi->dev, "adi,input-mode", &str); |
| if (ret) |
| st->input_mode = ADMV1013_IQ_MODE; |
| |
| if (!strcmp(str, "iq")) |
| st->input_mode = ADMV1013_IQ_MODE; |
| else if (!strcmp(str, "if")) |
| st->input_mode = ADMV1013_IF_MODE; |
| else |
| return -EINVAL; |
| |
| ret = device_property_read_string(&spi->dev, "adi,quad-se-mode", &str); |
| if (ret) |
| st->quad_se_mode = ADMV1013_SE_MODE_DIFF; |
| |
| if (!strcmp(str, "diff")) |
| st->quad_se_mode = ADMV1013_SE_MODE_DIFF; |
| else if (!strcmp(str, "se-pos")) |
| st->quad_se_mode = ADMV1013_SE_MODE_POS; |
| else if (!strcmp(str, "se-neg")) |
| st->quad_se_mode = ADMV1013_SE_MODE_NEG; |
| else |
| return -EINVAL; |
| |
| st->reg = devm_regulator_get(&spi->dev, "vcm"); |
| if (IS_ERR(st->reg)) |
| return dev_err_probe(&spi->dev, PTR_ERR(st->reg), |
| "failed to get the common-mode voltage\n"); |
| |
| ret = devm_regulator_bulk_get_enable(&st->spi->dev, |
| ARRAY_SIZE(admv1013_vcc_regs), |
| admv1013_vcc_regs); |
| if (ret) { |
| dev_err_probe(&spi->dev, ret, |
| "Failed to request VCC regulators\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int admv1013_probe(struct spi_device *spi) |
| { |
| struct iio_dev *indio_dev; |
| struct admv1013_state *st; |
| int ret; |
| |
| indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); |
| if (!indio_dev) |
| return -ENOMEM; |
| |
| st = iio_priv(indio_dev); |
| |
| indio_dev->info = &admv1013_info; |
| indio_dev->name = "admv1013"; |
| indio_dev->channels = admv1013_channels; |
| indio_dev->num_channels = ARRAY_SIZE(admv1013_channels); |
| |
| st->spi = spi; |
| |
| ret = admv1013_properties_parse(st); |
| if (ret) |
| return ret; |
| |
| ret = regulator_enable(st->reg); |
| if (ret) { |
| dev_err(&spi->dev, "Failed to enable specified Common-Mode Voltage!\n"); |
| return ret; |
| } |
| |
| ret = devm_add_action_or_reset(&spi->dev, admv1013_reg_disable, |
| st->reg); |
| if (ret) |
| return ret; |
| |
| st->clkin = devm_clk_get_enabled(&spi->dev, "lo_in"); |
| if (IS_ERR(st->clkin)) |
| return dev_err_probe(&spi->dev, PTR_ERR(st->clkin), |
| "failed to get the LO input clock\n"); |
| |
| st->nb.notifier_call = admv1013_freq_change; |
| ret = devm_clk_notifier_register(&spi->dev, st->clkin, &st->nb); |
| if (ret) |
| return ret; |
| |
| mutex_init(&st->lock); |
| |
| ret = admv1013_init(st); |
| if (ret) { |
| dev_err(&spi->dev, "admv1013 init failed\n"); |
| return ret; |
| } |
| |
| ret = devm_add_action_or_reset(&spi->dev, admv1013_powerdown, st); |
| if (ret) |
| return ret; |
| |
| return devm_iio_device_register(&spi->dev, indio_dev); |
| } |
| |
| static const struct spi_device_id admv1013_id[] = { |
| { "admv1013", 0 }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(spi, admv1013_id); |
| |
| static const struct of_device_id admv1013_of_match[] = { |
| { .compatible = "adi,admv1013" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, admv1013_of_match); |
| |
| static struct spi_driver admv1013_driver = { |
| .driver = { |
| .name = "admv1013", |
| .of_match_table = admv1013_of_match, |
| }, |
| .probe = admv1013_probe, |
| .id_table = admv1013_id, |
| }; |
| module_spi_driver(admv1013_driver); |
| |
| MODULE_AUTHOR("Antoniu Miclaus <antoniu.miclaus@analog.com"); |
| MODULE_DESCRIPTION("Analog Devices ADMV1013"); |
| MODULE_LICENSE("GPL v2"); |