| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * PCIe host controller driver for Axis ARTPEC-6 SoC |
| * |
| * Author: Niklas Cassel <niklas.cassel@axis.com> |
| * |
| * Based on work done by Phil Edworthy <phil@edworthys.org> |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/of.h> |
| #include <linux/pci.h> |
| #include <linux/platform_device.h> |
| #include <linux/resource.h> |
| #include <linux/signal.h> |
| #include <linux/types.h> |
| #include <linux/interrupt.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/regmap.h> |
| |
| #include "pcie-designware.h" |
| |
| #define to_artpec6_pcie(x) dev_get_drvdata((x)->dev) |
| |
| enum artpec_pcie_variants { |
| ARTPEC6, |
| ARTPEC7, |
| }; |
| |
| struct artpec6_pcie { |
| struct dw_pcie *pci; |
| struct regmap *regmap; /* DT axis,syscon-pcie */ |
| void __iomem *phy_base; /* DT phy */ |
| enum artpec_pcie_variants variant; |
| enum dw_pcie_device_mode mode; |
| }; |
| |
| struct artpec_pcie_of_data { |
| enum artpec_pcie_variants variant; |
| enum dw_pcie_device_mode mode; |
| }; |
| |
| static const struct of_device_id artpec6_pcie_of_match[]; |
| |
| /* ARTPEC-6 specific registers */ |
| #define PCIECFG 0x18 |
| #define PCIECFG_DBG_OEN BIT(24) |
| #define PCIECFG_CORE_RESET_REQ BIT(21) |
| #define PCIECFG_LTSSM_ENABLE BIT(20) |
| #define PCIECFG_DEVICE_TYPE_MASK GENMASK(19, 16) |
| #define PCIECFG_CLKREQ_B BIT(11) |
| #define PCIECFG_REFCLK_ENABLE BIT(10) |
| #define PCIECFG_PLL_ENABLE BIT(9) |
| #define PCIECFG_PCLK_ENABLE BIT(8) |
| #define PCIECFG_RISRCREN BIT(4) |
| #define PCIECFG_MODE_TX_DRV_EN BIT(3) |
| #define PCIECFG_CISRREN BIT(2) |
| #define PCIECFG_MACRO_ENABLE BIT(0) |
| /* ARTPEC-7 specific fields */ |
| #define PCIECFG_REFCLKSEL BIT(23) |
| #define PCIECFG_NOC_RESET BIT(3) |
| |
| #define PCIESTAT 0x1c |
| /* ARTPEC-7 specific fields */ |
| #define PCIESTAT_EXTREFCLK BIT(3) |
| |
| #define NOCCFG 0x40 |
| #define NOCCFG_ENABLE_CLK_PCIE BIT(4) |
| #define NOCCFG_POWER_PCIE_IDLEACK BIT(3) |
| #define NOCCFG_POWER_PCIE_IDLE BIT(2) |
| #define NOCCFG_POWER_PCIE_IDLEREQ BIT(1) |
| |
| #define PHY_STATUS 0x118 |
| #define PHY_COSPLLLOCK BIT(0) |
| |
| #define PHY_TX_ASIC_OUT 0x4040 |
| #define PHY_TX_ASIC_OUT_TX_ACK BIT(0) |
| |
| #define PHY_RX_ASIC_OUT 0x405c |
| #define PHY_RX_ASIC_OUT_ACK BIT(0) |
| |
| static u32 artpec6_pcie_readl(struct artpec6_pcie *artpec6_pcie, u32 offset) |
| { |
| u32 val; |
| |
| regmap_read(artpec6_pcie->regmap, offset, &val); |
| return val; |
| } |
| |
| static void artpec6_pcie_writel(struct artpec6_pcie *artpec6_pcie, u32 offset, u32 val) |
| { |
| regmap_write(artpec6_pcie->regmap, offset, val); |
| } |
| |
| static u64 artpec6_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr) |
| { |
| struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci); |
| struct dw_pcie_rp *pp = &pci->pp; |
| struct dw_pcie_ep *ep = &pci->ep; |
| |
| switch (artpec6_pcie->mode) { |
| case DW_PCIE_RC_TYPE: |
| return pci_addr - pp->cfg0_base; |
| case DW_PCIE_EP_TYPE: |
| return pci_addr - ep->phys_base; |
| default: |
| dev_err(pci->dev, "UNKNOWN device type\n"); |
| } |
| return pci_addr; |
| } |
| |
| static int artpec6_pcie_establish_link(struct dw_pcie *pci) |
| { |
| struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci); |
| u32 val; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val |= PCIECFG_LTSSM_ENABLE; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| |
| return 0; |
| } |
| |
| static void artpec6_pcie_stop_link(struct dw_pcie *pci) |
| { |
| struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci); |
| u32 val; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val &= ~PCIECFG_LTSSM_ENABLE; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| } |
| |
| static const struct dw_pcie_ops dw_pcie_ops = { |
| .cpu_addr_fixup = artpec6_pcie_cpu_addr_fixup, |
| .start_link = artpec6_pcie_establish_link, |
| .stop_link = artpec6_pcie_stop_link, |
| }; |
| |
| static void artpec6_pcie_wait_for_phy_a6(struct artpec6_pcie *artpec6_pcie) |
| { |
| struct dw_pcie *pci = artpec6_pcie->pci; |
| struct device *dev = pci->dev; |
| u32 val; |
| unsigned int retries; |
| |
| retries = 50; |
| do { |
| usleep_range(1000, 2000); |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| retries--; |
| } while (retries && |
| (val & (NOCCFG_POWER_PCIE_IDLEACK | NOCCFG_POWER_PCIE_IDLE))); |
| if (!retries) |
| dev_err(dev, "PCIe clock manager did not leave idle state\n"); |
| |
| retries = 50; |
| do { |
| usleep_range(1000, 2000); |
| val = readl(artpec6_pcie->phy_base + PHY_STATUS); |
| retries--; |
| } while (retries && !(val & PHY_COSPLLLOCK)); |
| if (!retries) |
| dev_err(dev, "PHY PLL did not lock\n"); |
| } |
| |
| static void artpec6_pcie_wait_for_phy_a7(struct artpec6_pcie *artpec6_pcie) |
| { |
| struct dw_pcie *pci = artpec6_pcie->pci; |
| struct device *dev = pci->dev; |
| u32 val; |
| u16 phy_status_tx, phy_status_rx; |
| unsigned int retries; |
| |
| retries = 50; |
| do { |
| usleep_range(1000, 2000); |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| retries--; |
| } while (retries && |
| (val & (NOCCFG_POWER_PCIE_IDLEACK | NOCCFG_POWER_PCIE_IDLE))); |
| if (!retries) |
| dev_err(dev, "PCIe clock manager did not leave idle state\n"); |
| |
| retries = 50; |
| do { |
| usleep_range(1000, 2000); |
| phy_status_tx = readw(artpec6_pcie->phy_base + PHY_TX_ASIC_OUT); |
| phy_status_rx = readw(artpec6_pcie->phy_base + PHY_RX_ASIC_OUT); |
| retries--; |
| } while (retries && ((phy_status_tx & PHY_TX_ASIC_OUT_TX_ACK) || |
| (phy_status_rx & PHY_RX_ASIC_OUT_ACK))); |
| if (!retries) |
| dev_err(dev, "PHY did not enter Pn state\n"); |
| } |
| |
| static void artpec6_pcie_wait_for_phy(struct artpec6_pcie *artpec6_pcie) |
| { |
| switch (artpec6_pcie->variant) { |
| case ARTPEC6: |
| artpec6_pcie_wait_for_phy_a6(artpec6_pcie); |
| break; |
| case ARTPEC7: |
| artpec6_pcie_wait_for_phy_a7(artpec6_pcie); |
| break; |
| } |
| } |
| |
| static void artpec6_pcie_init_phy_a6(struct artpec6_pcie *artpec6_pcie) |
| { |
| u32 val; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val |= PCIECFG_RISRCREN | /* Receiver term. 50 Ohm */ |
| PCIECFG_MODE_TX_DRV_EN | |
| PCIECFG_CISRREN | /* Reference clock term. 100 Ohm */ |
| PCIECFG_MACRO_ENABLE; |
| val |= PCIECFG_REFCLK_ENABLE; |
| val &= ~PCIECFG_DBG_OEN; |
| val &= ~PCIECFG_CLKREQ_B; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| usleep_range(5000, 6000); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| val |= NOCCFG_ENABLE_CLK_PCIE; |
| artpec6_pcie_writel(artpec6_pcie, NOCCFG, val); |
| usleep_range(20, 30); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val |= PCIECFG_PCLK_ENABLE | PCIECFG_PLL_ENABLE; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| usleep_range(6000, 7000); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| val &= ~NOCCFG_POWER_PCIE_IDLEREQ; |
| artpec6_pcie_writel(artpec6_pcie, NOCCFG, val); |
| } |
| |
| static void artpec6_pcie_init_phy_a7(struct artpec6_pcie *artpec6_pcie) |
| { |
| struct dw_pcie *pci = artpec6_pcie->pci; |
| u32 val; |
| bool extrefclk; |
| |
| /* Check if external reference clock is connected */ |
| val = artpec6_pcie_readl(artpec6_pcie, PCIESTAT); |
| extrefclk = !!(val & PCIESTAT_EXTREFCLK); |
| dev_dbg(pci->dev, "Using reference clock: %s\n", |
| extrefclk ? "external" : "internal"); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val |= PCIECFG_RISRCREN | /* Receiver term. 50 Ohm */ |
| PCIECFG_PCLK_ENABLE; |
| if (extrefclk) |
| val |= PCIECFG_REFCLKSEL; |
| else |
| val &= ~PCIECFG_REFCLKSEL; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| usleep_range(10, 20); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| val |= NOCCFG_ENABLE_CLK_PCIE; |
| artpec6_pcie_writel(artpec6_pcie, NOCCFG, val); |
| usleep_range(20, 30); |
| |
| val = artpec6_pcie_readl(artpec6_pcie, NOCCFG); |
| val &= ~NOCCFG_POWER_PCIE_IDLEREQ; |
| artpec6_pcie_writel(artpec6_pcie, NOCCFG, val); |
| } |
| |
| static void artpec6_pcie_init_phy(struct artpec6_pcie *artpec6_pcie) |
| { |
| switch (artpec6_pcie->variant) { |
| case ARTPEC6: |
| artpec6_pcie_init_phy_a6(artpec6_pcie); |
| break; |
| case ARTPEC7: |
| artpec6_pcie_init_phy_a7(artpec6_pcie); |
| break; |
| } |
| } |
| |
| static void artpec6_pcie_assert_core_reset(struct artpec6_pcie *artpec6_pcie) |
| { |
| u32 val; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| switch (artpec6_pcie->variant) { |
| case ARTPEC6: |
| val |= PCIECFG_CORE_RESET_REQ; |
| break; |
| case ARTPEC7: |
| val &= ~PCIECFG_NOC_RESET; |
| break; |
| } |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| } |
| |
| static void artpec6_pcie_deassert_core_reset(struct artpec6_pcie *artpec6_pcie) |
| { |
| u32 val; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| switch (artpec6_pcie->variant) { |
| case ARTPEC6: |
| val &= ~PCIECFG_CORE_RESET_REQ; |
| break; |
| case ARTPEC7: |
| val |= PCIECFG_NOC_RESET; |
| break; |
| } |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| usleep_range(100, 200); |
| } |
| |
| static int artpec6_pcie_host_init(struct dw_pcie_rp *pp) |
| { |
| struct dw_pcie *pci = to_dw_pcie_from_pp(pp); |
| struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci); |
| |
| if (artpec6_pcie->variant == ARTPEC7) { |
| pci->n_fts[0] = 180; |
| pci->n_fts[1] = 180; |
| } |
| artpec6_pcie_assert_core_reset(artpec6_pcie); |
| artpec6_pcie_init_phy(artpec6_pcie); |
| artpec6_pcie_deassert_core_reset(artpec6_pcie); |
| artpec6_pcie_wait_for_phy(artpec6_pcie); |
| |
| return 0; |
| } |
| |
| static const struct dw_pcie_host_ops artpec6_pcie_host_ops = { |
| .init = artpec6_pcie_host_init, |
| }; |
| |
| static void artpec6_pcie_ep_init(struct dw_pcie_ep *ep) |
| { |
| struct dw_pcie *pci = to_dw_pcie_from_ep(ep); |
| struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci); |
| enum pci_barno bar; |
| |
| artpec6_pcie_assert_core_reset(artpec6_pcie); |
| artpec6_pcie_init_phy(artpec6_pcie); |
| artpec6_pcie_deassert_core_reset(artpec6_pcie); |
| artpec6_pcie_wait_for_phy(artpec6_pcie); |
| |
| for (bar = 0; bar < PCI_STD_NUM_BARS; bar++) |
| dw_pcie_ep_reset_bar(pci, bar); |
| } |
| |
| static int artpec6_pcie_raise_irq(struct dw_pcie_ep *ep, u8 func_no, |
| unsigned int type, u16 interrupt_num) |
| { |
| struct dw_pcie *pci = to_dw_pcie_from_ep(ep); |
| |
| switch (type) { |
| case PCI_IRQ_INTX: |
| dev_err(pci->dev, "EP cannot trigger INTx IRQs\n"); |
| return -EINVAL; |
| case PCI_IRQ_MSI: |
| return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num); |
| default: |
| dev_err(pci->dev, "UNKNOWN IRQ type\n"); |
| } |
| |
| return 0; |
| } |
| |
| static const struct dw_pcie_ep_ops pcie_ep_ops = { |
| .init = artpec6_pcie_ep_init, |
| .raise_irq = artpec6_pcie_raise_irq, |
| }; |
| |
| static int artpec6_pcie_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct dw_pcie *pci; |
| struct artpec6_pcie *artpec6_pcie; |
| int ret; |
| const struct artpec_pcie_of_data *data; |
| enum artpec_pcie_variants variant; |
| enum dw_pcie_device_mode mode; |
| u32 val; |
| |
| data = of_device_get_match_data(dev); |
| if (!data) |
| return -EINVAL; |
| |
| variant = (enum artpec_pcie_variants)data->variant; |
| mode = (enum dw_pcie_device_mode)data->mode; |
| |
| artpec6_pcie = devm_kzalloc(dev, sizeof(*artpec6_pcie), GFP_KERNEL); |
| if (!artpec6_pcie) |
| return -ENOMEM; |
| |
| pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL); |
| if (!pci) |
| return -ENOMEM; |
| |
| pci->dev = dev; |
| pci->ops = &dw_pcie_ops; |
| |
| artpec6_pcie->pci = pci; |
| artpec6_pcie->variant = variant; |
| artpec6_pcie->mode = mode; |
| |
| artpec6_pcie->phy_base = |
| devm_platform_ioremap_resource_byname(pdev, "phy"); |
| if (IS_ERR(artpec6_pcie->phy_base)) |
| return PTR_ERR(artpec6_pcie->phy_base); |
| |
| artpec6_pcie->regmap = |
| syscon_regmap_lookup_by_phandle(dev->of_node, |
| "axis,syscon-pcie"); |
| if (IS_ERR(artpec6_pcie->regmap)) |
| return PTR_ERR(artpec6_pcie->regmap); |
| |
| platform_set_drvdata(pdev, artpec6_pcie); |
| |
| switch (artpec6_pcie->mode) { |
| case DW_PCIE_RC_TYPE: |
| if (!IS_ENABLED(CONFIG_PCIE_ARTPEC6_HOST)) |
| return -ENODEV; |
| |
| pci->pp.ops = &artpec6_pcie_host_ops; |
| |
| ret = dw_pcie_host_init(&pci->pp); |
| if (ret < 0) |
| return ret; |
| break; |
| case DW_PCIE_EP_TYPE: |
| if (!IS_ENABLED(CONFIG_PCIE_ARTPEC6_EP)) |
| return -ENODEV; |
| |
| val = artpec6_pcie_readl(artpec6_pcie, PCIECFG); |
| val &= ~PCIECFG_DEVICE_TYPE_MASK; |
| artpec6_pcie_writel(artpec6_pcie, PCIECFG, val); |
| |
| pci->ep.ops = &pcie_ep_ops; |
| |
| return dw_pcie_ep_init(&pci->ep); |
| default: |
| dev_err(dev, "INVALID device type %d\n", artpec6_pcie->mode); |
| } |
| |
| return 0; |
| } |
| |
| static const struct artpec_pcie_of_data artpec6_pcie_rc_of_data = { |
| .variant = ARTPEC6, |
| .mode = DW_PCIE_RC_TYPE, |
| }; |
| |
| static const struct artpec_pcie_of_data artpec6_pcie_ep_of_data = { |
| .variant = ARTPEC6, |
| .mode = DW_PCIE_EP_TYPE, |
| }; |
| |
| static const struct artpec_pcie_of_data artpec7_pcie_rc_of_data = { |
| .variant = ARTPEC7, |
| .mode = DW_PCIE_RC_TYPE, |
| }; |
| |
| static const struct artpec_pcie_of_data artpec7_pcie_ep_of_data = { |
| .variant = ARTPEC7, |
| .mode = DW_PCIE_EP_TYPE, |
| }; |
| |
| static const struct of_device_id artpec6_pcie_of_match[] = { |
| { |
| .compatible = "axis,artpec6-pcie", |
| .data = &artpec6_pcie_rc_of_data, |
| }, |
| { |
| .compatible = "axis,artpec6-pcie-ep", |
| .data = &artpec6_pcie_ep_of_data, |
| }, |
| { |
| .compatible = "axis,artpec7-pcie", |
| .data = &artpec7_pcie_rc_of_data, |
| }, |
| { |
| .compatible = "axis,artpec7-pcie-ep", |
| .data = &artpec7_pcie_ep_of_data, |
| }, |
| {}, |
| }; |
| |
| static struct platform_driver artpec6_pcie_driver = { |
| .probe = artpec6_pcie_probe, |
| .driver = { |
| .name = "artpec6-pcie", |
| .of_match_table = artpec6_pcie_of_match, |
| .suppress_bind_attrs = true, |
| }, |
| }; |
| builtin_platform_driver(artpec6_pcie_driver); |