| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2021 NXP |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/mfd/syscon/imx7-iomuxc-gpr.h> |
| #include <linux/module.h> |
| #include <linux/phy/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| |
| #include <dt-bindings/phy/phy-imx8-pcie.h> |
| |
| #define IMX8MM_PCIE_PHY_CMN_REG061 0x184 |
| #define ANA_PLL_CLK_OUT_TO_EXT_IO_EN BIT(0) |
| #define IMX8MM_PCIE_PHY_CMN_REG062 0x188 |
| #define ANA_PLL_CLK_OUT_TO_EXT_IO_SEL BIT(3) |
| #define IMX8MM_PCIE_PHY_CMN_REG063 0x18C |
| #define AUX_PLL_REFCLK_SEL_SYS_PLL GENMASK(7, 6) |
| #define IMX8MM_PCIE_PHY_CMN_REG064 0x190 |
| #define ANA_AUX_RX_TX_SEL_TX BIT(7) |
| #define ANA_AUX_RX_TERM_GND_EN BIT(3) |
| #define ANA_AUX_TX_TERM BIT(2) |
| #define IMX8MM_PCIE_PHY_CMN_REG065 0x194 |
| #define ANA_AUX_RX_TERM (BIT(7) | BIT(4)) |
| #define ANA_AUX_TX_LVL GENMASK(3, 0) |
| #define IMX8MM_PCIE_PHY_CMN_REG75 0x1D4 |
| #define PCIE_PHY_CMN_REG75_PLL_DONE 0x3 |
| #define PCIE_PHY_TRSV_REG5 0x414 |
| #define PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D |
| #define PCIE_PHY_TRSV_REG6 0x418 |
| #define PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF |
| |
| #define IMX8MM_GPR_PCIE_REF_CLK_SEL GENMASK(25, 24) |
| #define IMX8MM_GPR_PCIE_REF_CLK_PLL FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x3) |
| #define IMX8MM_GPR_PCIE_REF_CLK_EXT FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x2) |
| #define IMX8MM_GPR_PCIE_AUX_EN BIT(19) |
| #define IMX8MM_GPR_PCIE_CMN_RST BIT(18) |
| #define IMX8MM_GPR_PCIE_POWER_OFF BIT(17) |
| #define IMX8MM_GPR_PCIE_SSC_EN BIT(16) |
| #define IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE BIT(9) |
| |
| struct imx8_pcie_phy { |
| void __iomem *base; |
| struct clk *clk; |
| struct phy *phy; |
| struct regmap *iomuxc_gpr; |
| struct reset_control *reset; |
| u32 refclk_pad_mode; |
| u32 tx_deemph_gen1; |
| u32 tx_deemph_gen2; |
| bool clkreq_unused; |
| }; |
| |
| static int imx8_pcie_phy_init(struct phy *phy) |
| { |
| int ret; |
| u32 val, pad_mode; |
| struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy); |
| |
| reset_control_assert(imx8_phy->reset); |
| |
| pad_mode = imx8_phy->refclk_pad_mode; |
| /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */ |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE, |
| imx8_phy->clkreq_unused ? |
| 0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE); |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_AUX_EN, |
| IMX8MM_GPR_PCIE_AUX_EN); |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_POWER_OFF, 0); |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_SSC_EN, 0); |
| |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_REF_CLK_SEL, |
| pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ? |
| IMX8MM_GPR_PCIE_REF_CLK_EXT : |
| IMX8MM_GPR_PCIE_REF_CLK_PLL); |
| usleep_range(100, 200); |
| |
| /* Do the PHY common block reset */ |
| regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, |
| IMX8MM_GPR_PCIE_CMN_RST, |
| IMX8MM_GPR_PCIE_CMN_RST); |
| usleep_range(200, 500); |
| |
| if (pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT || |
| pad_mode == IMX8_PCIE_REFCLK_PAD_UNUSED) { |
| /* Configure the pad as input */ |
| val = readl(imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061); |
| writel(val & ~ANA_PLL_CLK_OUT_TO_EXT_IO_EN, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061); |
| } else { |
| /* Configure the PHY to output the refclock via pad */ |
| writel(ANA_PLL_CLK_OUT_TO_EXT_IO_EN, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061); |
| } |
| |
| if (pad_mode == IMX8_PCIE_REFCLK_PAD_OUTPUT || |
| pad_mode == IMX8_PCIE_REFCLK_PAD_UNUSED) { |
| /* Source clock from SoC internal PLL */ |
| writel(ANA_PLL_CLK_OUT_TO_EXT_IO_SEL, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG062); |
| writel(AUX_PLL_REFCLK_SEL_SYS_PLL, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG063); |
| val = ANA_AUX_RX_TX_SEL_TX | ANA_AUX_TX_TERM; |
| writel(val | ANA_AUX_RX_TERM_GND_EN, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG064); |
| writel(ANA_AUX_RX_TERM | ANA_AUX_TX_LVL, |
| imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG065); |
| } |
| |
| /* Tune PHY de-emphasis setting to pass PCIe compliance. */ |
| if (imx8_phy->tx_deemph_gen1) |
| writel(imx8_phy->tx_deemph_gen1, |
| imx8_phy->base + PCIE_PHY_TRSV_REG5); |
| if (imx8_phy->tx_deemph_gen2) |
| writel(imx8_phy->tx_deemph_gen2, |
| imx8_phy->base + PCIE_PHY_TRSV_REG6); |
| |
| reset_control_deassert(imx8_phy->reset); |
| |
| /* Polling to check the phy is ready or not. */ |
| ret = readl_poll_timeout(imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG75, |
| val, val == PCIE_PHY_CMN_REG75_PLL_DONE, |
| 10, 20000); |
| return ret; |
| } |
| |
| static int imx8_pcie_phy_power_on(struct phy *phy) |
| { |
| struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy); |
| |
| return clk_prepare_enable(imx8_phy->clk); |
| } |
| |
| static int imx8_pcie_phy_power_off(struct phy *phy) |
| { |
| struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy); |
| |
| clk_disable_unprepare(imx8_phy->clk); |
| |
| return 0; |
| } |
| |
| static const struct phy_ops imx8_pcie_phy_ops = { |
| .init = imx8_pcie_phy_init, |
| .power_on = imx8_pcie_phy_power_on, |
| .power_off = imx8_pcie_phy_power_off, |
| .owner = THIS_MODULE, |
| }; |
| |
| static int imx8_pcie_phy_probe(struct platform_device *pdev) |
| { |
| struct phy_provider *phy_provider; |
| struct device *dev = &pdev->dev; |
| struct device_node *np = dev->of_node; |
| struct imx8_pcie_phy *imx8_phy; |
| struct resource *res; |
| |
| imx8_phy = devm_kzalloc(dev, sizeof(*imx8_phy), GFP_KERNEL); |
| if (!imx8_phy) |
| return -ENOMEM; |
| |
| /* get PHY refclk pad mode */ |
| of_property_read_u32(np, "fsl,refclk-pad-mode", |
| &imx8_phy->refclk_pad_mode); |
| |
| if (of_property_read_u32(np, "fsl,tx-deemph-gen1", |
| &imx8_phy->tx_deemph_gen1)) |
| imx8_phy->tx_deemph_gen1 = 0; |
| |
| if (of_property_read_u32(np, "fsl,tx-deemph-gen2", |
| &imx8_phy->tx_deemph_gen2)) |
| imx8_phy->tx_deemph_gen2 = 0; |
| |
| if (of_property_read_bool(np, "fsl,clkreq-unsupported")) |
| imx8_phy->clkreq_unused = true; |
| else |
| imx8_phy->clkreq_unused = false; |
| |
| imx8_phy->clk = devm_clk_get(dev, "ref"); |
| if (IS_ERR(imx8_phy->clk)) { |
| dev_err(dev, "failed to get imx pcie phy clock\n"); |
| return PTR_ERR(imx8_phy->clk); |
| } |
| |
| /* Grab GPR config register range */ |
| imx8_phy->iomuxc_gpr = |
| syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr"); |
| if (IS_ERR(imx8_phy->iomuxc_gpr)) { |
| dev_err(dev, "unable to find iomuxc registers\n"); |
| return PTR_ERR(imx8_phy->iomuxc_gpr); |
| } |
| |
| imx8_phy->reset = devm_reset_control_get_exclusive(dev, "pciephy"); |
| if (IS_ERR(imx8_phy->reset)) { |
| dev_err(dev, "Failed to get PCIEPHY reset control\n"); |
| return PTR_ERR(imx8_phy->reset); |
| } |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| imx8_phy->base = devm_ioremap_resource(dev, res); |
| if (IS_ERR(imx8_phy->base)) |
| return PTR_ERR(imx8_phy->base); |
| |
| imx8_phy->phy = devm_phy_create(dev, NULL, &imx8_pcie_phy_ops); |
| if (IS_ERR(imx8_phy->phy)) |
| return PTR_ERR(imx8_phy->phy); |
| |
| phy_set_drvdata(imx8_phy->phy, imx8_phy); |
| |
| phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); |
| |
| return PTR_ERR_OR_ZERO(phy_provider); |
| } |
| |
| static const struct of_device_id imx8_pcie_phy_of_match[] = { |
| {.compatible = "fsl,imx8mm-pcie-phy",}, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match); |
| |
| static struct platform_driver imx8_pcie_phy_driver = { |
| .probe = imx8_pcie_phy_probe, |
| .driver = { |
| .name = "imx8-pcie-phy", |
| .of_match_table = imx8_pcie_phy_of_match, |
| } |
| }; |
| module_platform_driver(imx8_pcie_phy_driver); |
| |
| MODULE_DESCRIPTION("FSL IMX8 PCIE PHY driver"); |
| MODULE_LICENSE("GPL v2"); |