| # SPDX-License-Identifier: GPL-2.0-only |
| menu "IEEE 1394 (FireWire) support" |
| depends on PCI || COMPILE_TEST |
| # firewire-core does not depend on PCI but is |
| # not useful without PCI controller driver |
| |
| config FIREWIRE |
| tristate "FireWire driver stack" |
| select CRC_ITU_T |
| help |
| This is the new-generation IEEE 1394 (FireWire) driver stack |
| a.k.a. Juju, a new implementation designed for robustness and |
| simplicity. |
| See http://ieee1394.wiki.kernel.org/index.php/Juju_Migration |
| for information about migration from the older Linux 1394 stack |
| to the new driver stack. |
| |
| To compile this driver as a module, say M here: the module will be |
| called firewire-core. |
| |
| config FIREWIRE_OHCI |
| tristate "OHCI-1394 controllers" |
| depends on PCI && FIREWIRE && MMU |
| help |
| Enable this driver if you have a FireWire controller based |
| on the OHCI specification. For all practical purposes, this |
| is the only chipset in use, so say Y here. |
| |
| To compile this driver as a module, say M here: The module will be |
| called firewire-ohci. |
| |
| config FIREWIRE_SBP2 |
| tristate "Storage devices (SBP-2 protocol)" |
| depends on FIREWIRE && SCSI |
| help |
| This option enables you to use SBP-2 devices connected to a |
| FireWire bus. SBP-2 devices include storage devices like |
| harddisks and DVD drives, also some other FireWire devices |
| like scanners. |
| |
| To compile this driver as a module, say M here: The module will be |
| called firewire-sbp2. |
| |
| You should also enable support for disks, CD-ROMs, etc. in the SCSI |
| configuration section. |
| |
| config FIREWIRE_NET |
| tristate "IP networking over 1394" |
| depends on FIREWIRE && INET |
| help |
| This enables IPv4/IPv6 over IEEE 1394, providing IP connectivity |
| with other implementations of RFC 2734/3146 as found on several |
| operating systems. Multicast support is currently limited. |
| |
| To compile this driver as a module, say M here: The module will be |
| called firewire-net. |
| |
| config FIREWIRE_NOSY |
| tristate "Nosy - a FireWire traffic sniffer for PCILynx cards" |
| depends on PCI |
| help |
| Nosy is an IEEE 1394 packet sniffer that is used for protocol |
| analysis and in development of IEEE 1394 drivers, applications, |
| or firmwares. |
| |
| This driver lets you use a Texas Instruments PCILynx 1394 to PCI |
| link layer controller TSB12LV21/A/B as a low-budget bus analyzer. |
| PCILynx is a nowadays very rare IEEE 1394 controller which is |
| not OHCI 1394 compliant. |
| |
| The following cards are known to be based on PCILynx or PCILynx-2: |
| IOI IOI-1394TT (PCI card), Unibrain Fireboard 400 PCI Lynx-2 |
| (PCI card), Newer Technology FireWire 2 Go (CardBus card), |
| Apple Power Mac G3 blue & white and G4 with PCI graphics |
| (onboard controller). |
| |
| To compile this driver as a module, say M here: The module will be |
| called nosy. Source code of a userspace interface to nosy, called |
| nosy-dump, can be found in tools/firewire/ of the kernel sources. |
| |
| If unsure, say N. |
| |
| endmenu |
