drivers/hwmon/pmbus/ucd9000.c - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * Hardware monitoring driver for UCD90xxx Sequencer and System Health
  * Controller series
  *
  * Copyright (C) 2011 Ericsson AB.
  */

 #include <linux/debugfs.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/init.h>
 #include <linux/err.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
 #include <linux/pmbus.h>
 #include <linux/gpio/driver.h>
 #include "pmbus.h"

 enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd90320, ucd9090,
 	     ucd90910 };

 #define UCD9000_MONITOR_CONFIG		0xd5
 #define UCD9000_NUM_PAGES		0xd6
 #define UCD9000_FAN_CONFIG_INDEX	0xe7
 #define UCD9000_FAN_CONFIG		0xe8
 #define UCD9000_MFR_STATUS		0xf3
 #define UCD9000_GPIO_SELECT		0xfa
 #define UCD9000_GPIO_CONFIG		0xfb
 #define UCD9000_DEVICE_ID		0xfd

 /* GPIO CONFIG bits */
 #define UCD9000_GPIO_CONFIG_ENABLE	BIT(0)
 #define UCD9000_GPIO_CONFIG_OUT_ENABLE	BIT(1)
 #define UCD9000_GPIO_CONFIG_OUT_VALUE	BIT(2)
 #define UCD9000_GPIO_CONFIG_STATUS	BIT(3)
 #define UCD9000_GPIO_INPUT		0
 #define UCD9000_GPIO_OUTPUT		1

 #define UCD9000_MON_TYPE(x)	(((x) >> 5) & 0x07)
 #define UCD9000_MON_PAGE(x)	((x) & 0x1f)

 #define UCD9000_MON_VOLTAGE	1
 #define UCD9000_MON_TEMPERATURE	2
 #define UCD9000_MON_CURRENT	3
 #define UCD9000_MON_VOLTAGE_HW	4

 #define UCD9000_NUM_FAN		4

 #define UCD9000_GPIO_NAME_LEN	16
 #define UCD9090_NUM_GPIOS	23
 #define UCD901XX_NUM_GPIOS	26
 #define UCD90320_NUM_GPIOS	84
 #define UCD90910_NUM_GPIOS	26

 #define UCD9000_DEBUGFS_NAME_LEN	24
 #define UCD9000_GPI_COUNT		8
 #define UCD90320_GPI_COUNT		32

 struct ucd9000_data {
 	u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
 	struct pmbus_driver_info info;
 #ifdef CONFIG_GPIOLIB
 	struct gpio_chip gpio;
 #endif
 	struct dentry *debugfs;
 };
 #define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)

 struct ucd9000_debugfs_entry {
 	struct i2c_client *client;
 	u8 index;
 };

 static int ucd9000_get_fan_config(struct i2c_client *client, int fan)
 {
 	int fan_config = 0;
 	struct ucd9000_data *data
 	  = to_ucd9000_data(pmbus_get_driver_info(client));

 	if (data->fan_data[fan][3] & 1)
 		fan_config |= PB_FAN_2_INSTALLED;   /* Use lower bit position */

 	/* Pulses/revolution */
 	fan_config |= (data->fan_data[fan][3] & 0x06) >> 1;

 	return fan_config;
 }

 static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg)
 {
 	int ret = 0;
 	int fan_config;

 	switch (reg) {
 	case PMBUS_FAN_CONFIG_12:
 		if (page > 0)
 			return -ENXIO;

 		ret = ucd9000_get_fan_config(client, 0);
 		if (ret < 0)
 			return ret;
 		fan_config = ret << 4;
 		ret = ucd9000_get_fan_config(client, 1);
 		if (ret < 0)
 			return ret;
 		fan_config |= ret;
 		ret = fan_config;
 		break;
 	case PMBUS_FAN_CONFIG_34:
 		if (page > 0)
 			return -ENXIO;

 		ret = ucd9000_get_fan_config(client, 2);
 		if (ret < 0)
 			return ret;
 		fan_config = ret << 4;
 		ret = ucd9000_get_fan_config(client, 3);
 		if (ret < 0)
 			return ret;
 		fan_config |= ret;
 		ret = fan_config;
 		break;
 	default:
 		ret = -ENODATA;
 		break;
 	}
 	return ret;
 }

 static const struct i2c_device_id ucd9000_id[] = {
 	{"ucd9000", ucd9000},
 	{"ucd90120", ucd90120},
 	{"ucd90124", ucd90124},
 	{"ucd90160", ucd90160},
 	{"ucd90320", ucd90320},
 	{"ucd9090", ucd9090},
 	{"ucd90910", ucd90910},
 	{}
 };
 MODULE_DEVICE_TABLE(i2c, ucd9000_id);

 static const struct of_device_id __maybe_unused ucd9000_of_match[] = {
 	{
 		.compatible = "ti,ucd9000",
 		.data = (void *)ucd9000
 	},
 	{
 		.compatible = "ti,ucd90120",
 		.data = (void *)ucd90120
 	},
 	{
 		.compatible = "ti,ucd90124",
 		.data = (void *)ucd90124
 	},
 	{
 		.compatible = "ti,ucd90160",
 		.data = (void *)ucd90160
 	},
 	{
 		.compatible = "ti,ucd90320",
 		.data = (void *)ucd90320
 	},
 	{
 		.compatible = "ti,ucd9090",
 		.data = (void *)ucd9090
 	},
 	{
 		.compatible = "ti,ucd90910",
 		.data = (void *)ucd90910
 	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, ucd9000_of_match);

 #ifdef CONFIG_GPIOLIB
 static int ucd9000_gpio_read_config(struct i2c_client *client,
 				    unsigned int offset)
 {
 	int ret;

 	/* No page set required */
 	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT, offset);
 	if (ret < 0)
 		return ret;

 	return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
 }

 static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
 {
 	struct i2c_client *client  = gpiochip_get_data(gc);
 	int ret;

 	ret = ucd9000_gpio_read_config(client, offset);
 	if (ret < 0)
 		return ret;

 	return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
 }

 static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
 			     int value)
 {
 	struct i2c_client *client = gpiochip_get_data(gc);
 	int ret;

 	ret = ucd9000_gpio_read_config(client, offset);
 	if (ret < 0) {
 		dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
 			offset, ret);
 		return;
 	}

 	if (value) {
 		if (ret & UCD9000_GPIO_CONFIG_STATUS)
 			return;

 		ret |= UCD9000_GPIO_CONFIG_STATUS;
 	} else {
 		if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
 			return;

 		ret &= ~UCD9000_GPIO_CONFIG_STATUS;
 	}

 	ret |= UCD9000_GPIO_CONFIG_ENABLE;

 	/* Page set not required */
 	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
 	if (ret < 0) {
 		dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
 			offset, ret);
 		return;
 	}

 	ret &= ~UCD9000_GPIO_CONFIG_ENABLE;

 	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
 	if (ret < 0)
 		dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
 			offset, ret);
 }

 static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
 				      unsigned int offset)
 {
 	struct i2c_client *client = gpiochip_get_data(gc);
 	int ret;

 	ret = ucd9000_gpio_read_config(client, offset);
 	if (ret < 0)
 		return ret;

 	return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
 }

 static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
 				      unsigned int offset, bool direction_out,
 				      int requested_out)
 {
 	struct i2c_client *client = gpiochip_get_data(gc);
 	int ret, config, out_val;

 	ret = ucd9000_gpio_read_config(client, offset);
 	if (ret < 0)
 		return ret;

 	if (direction_out) {
 		out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;

 		if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
 			if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
 				return 0;
 		} else {
 			ret |= UCD9000_GPIO_CONFIG_OUT_ENABLE;
 		}

 		if (out_val)
 			ret |= UCD9000_GPIO_CONFIG_OUT_VALUE;
 		else
 			ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;

 	} else {
 		if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
 			return 0;

 		ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
 	}

 	ret |= UCD9000_GPIO_CONFIG_ENABLE;
 	config = ret;

 	/* Page set not required */
 	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
 	if (ret < 0)
 		return ret;

 	config &= ~UCD9000_GPIO_CONFIG_ENABLE;

 	return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
 }

 static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
 					unsigned int offset)
 {
 	return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT, 0);
 }

 static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
 					 unsigned int offset, int val)
 {
 	return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
 					  val);
 }

 static void ucd9000_probe_gpio(struct i2c_client *client,
 			       const struct i2c_device_id *mid,
 			       struct ucd9000_data *data)
 {
 	int rc;

 	switch (mid->driver_data) {
 	case ucd9090:
 		data->gpio.ngpio = UCD9090_NUM_GPIOS;
 		break;
 	case ucd90120:
 	case ucd90124:
 	case ucd90160:
 		data->gpio.ngpio = UCD901XX_NUM_GPIOS;
 		break;
 	case ucd90320:
 		data->gpio.ngpio = UCD90320_NUM_GPIOS;
 		break;
 	case ucd90910:
 		data->gpio.ngpio = UCD90910_NUM_GPIOS;
 		break;
 	default:
 		return; /* GPIO support is optional. */
 	}

 	/*
 	 * Pinmux support has not been added to the new gpio_chip.
 	 * This support should be added when possible given the mux
 	 * behavior of these IO devices.
 	 */
 	data->gpio.label = client->name;
 	data->gpio.get_direction = ucd9000_gpio_get_direction;
 	data->gpio.direction_input = ucd9000_gpio_direction_input;
 	data->gpio.direction_output = ucd9000_gpio_direction_output;
 	data->gpio.get = ucd9000_gpio_get;
 	data->gpio.set = ucd9000_gpio_set;
 	data->gpio.can_sleep = true;
 	data->gpio.base = -1;
 	data->gpio.parent = &client->dev;

 	rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
 	if (rc)
 		dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
 }
 #else
 static void ucd9000_probe_gpio(struct i2c_client *client,
 			       const struct i2c_device_id *mid,
 			       struct ucd9000_data *data)
 {
 }
 #endif /* CONFIG_GPIOLIB */

 #ifdef CONFIG_DEBUG_FS
 static int ucd9000_get_mfr_status(struct i2c_client *client, u8 *buffer)
 {
 	int ret = pmbus_set_page(client, 0, 0xff);

 	if (ret < 0)
 		return ret;

 	return i2c_smbus_read_block_data(client, UCD9000_MFR_STATUS, buffer);
 }

 static int ucd9000_debugfs_show_mfr_status_bit(void *data, u64 *val)
 {
 	struct ucd9000_debugfs_entry *entry = data;
 	struct i2c_client *client = entry->client;
 	u8 buffer[I2C_SMBUS_BLOCK_MAX];
 	int ret, i;

 	ret = ucd9000_get_mfr_status(client, buffer);
 	if (ret < 0)
 		return ret;

 	/*
 	 * GPI fault bits are in sets of 8, two bytes from end of response.
 	 */
 	i = ret - 3 - entry->index / 8;
 	if (i >= 0)
 		*val = !!(buffer[i] & BIT(entry->index % 8));

 	return 0;
 }
 DEFINE_DEBUGFS_ATTRIBUTE(ucd9000_debugfs_mfr_status_bit,
 			 ucd9000_debugfs_show_mfr_status_bit, NULL, "%1lld\n");

 static ssize_t ucd9000_debugfs_read_mfr_status(struct file *file,
 					       char __user *buf, size_t count,
 					       loff_t *ppos)
 {
 	struct i2c_client *client = file->private_data;
 	u8 buffer[I2C_SMBUS_BLOCK_MAX];
 	char str[(I2C_SMBUS_BLOCK_MAX * 2) + 2];
 	char *res;
 	int rc;

 	rc = ucd9000_get_mfr_status(client, buffer);
 	if (rc < 0)
 		return rc;

 	res = bin2hex(str, buffer, min(rc, I2C_SMBUS_BLOCK_MAX));
 	*res++ = '\n';
 	*res = 0;

 	return simple_read_from_buffer(buf, count, ppos, str, res - str);
 }

 static const struct file_operations ucd9000_debugfs_show_mfr_status_fops = {
 	.llseek = noop_llseek,
 	.read = ucd9000_debugfs_read_mfr_status,
 	.open = simple_open,
 };

 static int ucd9000_init_debugfs(struct i2c_client *client,
 				const struct i2c_device_id *mid,
 				struct ucd9000_data *data)
 {
 	struct dentry *debugfs;
 	struct ucd9000_debugfs_entry *entries;
 	int i, gpi_count;
 	char name[UCD9000_DEBUGFS_NAME_LEN];

 	debugfs = pmbus_get_debugfs_dir(client);
 	if (!debugfs)
 		return -ENOENT;

 	data->debugfs = debugfs_create_dir(client->name, debugfs);
 	if (!data->debugfs)
 		return -ENOENT;

 	/*
 	 * Of the chips this driver supports, only the UCD9090, UCD90160,
 	 * UCD90320, and UCD90910 report GPI faults in their MFR_STATUS
 	 * register, so only create the GPI fault debugfs attributes for those
 	 * chips.
 	 */
 	if (mid->driver_data == ucd9090 || mid->driver_data == ucd90160 ||
 	    mid->driver_data == ucd90320 || mid->driver_data == ucd90910) {
 		gpi_count = mid->driver_data == ucd90320 ? UCD90320_GPI_COUNT
 							 : UCD9000_GPI_COUNT;
 		entries = devm_kcalloc(&client->dev,
 				       gpi_count, sizeof(*entries),
 				       GFP_KERNEL);
 		if (!entries)
 			return -ENOMEM;

 		for (i = 0; i < gpi_count; i++) {
 			entries[i].client = client;
 			entries[i].index = i;
 			scnprintf(name, UCD9000_DEBUGFS_NAME_LEN,
 				  "gpi%d_alarm", i + 1);
 			debugfs_create_file(name, 0444, data->debugfs,
 					    &entries[i],
 					    &ucd9000_debugfs_mfr_status_bit);
 		}
 	}

 	scnprintf(name, UCD9000_DEBUGFS_NAME_LEN, "mfr_status");
 	debugfs_create_file(name, 0444, data->debugfs, client,
 			    &ucd9000_debugfs_show_mfr_status_fops);

 	return 0;
 }
 #else
 static int ucd9000_init_debugfs(struct i2c_client *client,
 				const struct i2c_device_id *mid,
 				struct ucd9000_data *data)
 {
 	return 0;
 }
 #endif /* CONFIG_DEBUG_FS */

 static int ucd9000_probe(struct i2c_client *client)
 {
 	u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
 	struct ucd9000_data *data;
 	struct pmbus_driver_info *info;
 	const struct i2c_device_id *mid;
 	enum chips chip;
 	int i, ret;

 	if (!i2c_check_functionality(client->adapter,
 				     I2C_FUNC_SMBUS_BYTE_DATA |
 				     I2C_FUNC_SMBUS_BLOCK_DATA))
 		return -ENODEV;

 	ret = i2c_smbus_read_block_data(client, UCD9000_DEVICE_ID,
 					block_buffer);
 	if (ret < 0) {
 		dev_err(&client->dev, "Failed to read device ID\n");
 		return ret;
 	}
 	block_buffer[ret] = '\0';
 	dev_info(&client->dev, "Device ID %s\n", block_buffer);

 	for (mid = ucd9000_id; mid->name[0]; mid++) {
 		if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
 			break;
 	}
 	if (!mid->name[0]) {
 		dev_err(&client->dev, "Unsupported device\n");
 		return -ENODEV;
 	}

 	if (client->dev.of_node)
 		chip = (enum chips)of_device_get_match_data(&client->dev);
 	else
 		chip = mid->driver_data;

 	if (chip != ucd9000 && strcmp(client->name, mid->name) != 0)
 		dev_notice(&client->dev,
 			   "Device mismatch: Configured %s, detected %s\n",
 			   client->name, mid->name);

 	data = devm_kzalloc(&client->dev, sizeof(struct ucd9000_data),
 			    GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 	info = &data->info;

 	ret = i2c_smbus_read_byte_data(client, UCD9000_NUM_PAGES);
 	if (ret < 0) {
 		dev_err(&client->dev,
 			"Failed to read number of active pages\n");
 		return ret;
 	}
 	info->pages = ret;
 	if (!info->pages) {
 		dev_err(&client->dev, "No pages configured\n");
 		return -ENODEV;
 	}

 	/* The internal temperature sensor is always active */
 	info->func[0] = PMBUS_HAVE_TEMP;

 	/* Everything else is configurable */
 	ret = i2c_smbus_read_block_data(client, UCD9000_MONITOR_CONFIG,
 					block_buffer);
 	if (ret <= 0) {
 		dev_err(&client->dev, "Failed to read configuration data\n");
 		return -ENODEV;
 	}
 	for (i = 0; i < ret; i++) {
 		int page = UCD9000_MON_PAGE(block_buffer[i]);

 		if (page >= info->pages)
 			continue;

 		switch (UCD9000_MON_TYPE(block_buffer[i])) {
 		case UCD9000_MON_VOLTAGE:
 		case UCD9000_MON_VOLTAGE_HW:
 			info->func[page] |= PMBUS_HAVE_VOUT
 			  | PMBUS_HAVE_STATUS_VOUT;
 			break;
 		case UCD9000_MON_TEMPERATURE:
 			info->func[page] |= PMBUS_HAVE_TEMP2
 			  | PMBUS_HAVE_STATUS_TEMP;
 			break;
 		case UCD9000_MON_CURRENT:
 			info->func[page] |= PMBUS_HAVE_IOUT
 			  | PMBUS_HAVE_STATUS_IOUT;
 			break;
 		default:
 			break;
 		}
 	}

 	/* Fan configuration */
 	if (mid->driver_data == ucd90124) {
 		for (i = 0; i < UCD9000_NUM_FAN; i++) {
 			i2c_smbus_write_byte_data(client,
 						  UCD9000_FAN_CONFIG_INDEX, i);
 			ret = i2c_smbus_read_block_data(client,
 							UCD9000_FAN_CONFIG,
 							data->fan_data[i]);
 			if (ret < 0)
 				return ret;
 		}
 		i2c_smbus_write_byte_data(client, UCD9000_FAN_CONFIG_INDEX, 0);

 		info->read_byte_data = ucd9000_read_byte_data;
 		info->func[0] |= PMBUS_HAVE_FAN12 | PMBUS_HAVE_STATUS_FAN12
 		  | PMBUS_HAVE_FAN34 | PMBUS_HAVE_STATUS_FAN34;
 	}

 	ucd9000_probe_gpio(client, mid, data);

 	ret = pmbus_do_probe(client, info);
 	if (ret)
 		return ret;

 	ret = ucd9000_init_debugfs(client, mid, data);
 	if (ret)
 		dev_warn(&client->dev, "Failed to register debugfs: %d\n",
 			 ret);

 	return 0;
 }

 /* This is the driver that will be inserted */
 static struct i2c_driver ucd9000_driver = {
 	.driver = {
 		.name = "ucd9000",
 		.of_match_table = of_match_ptr(ucd9000_of_match),
 	},
 	.probe_new = ucd9000_probe,
 	.remove = pmbus_do_remove,
 	.id_table = ucd9000_id,
 };

 module_i2c_driver(ucd9000_driver);

 MODULE_AUTHOR("Guenter Roeck");
 MODULE_DESCRIPTION("PMBus driver for TI UCD90xxx");
 MODULE_LICENSE("GPL");
	// SPDX-License-Identifier: GPL-2.0-or-later
	/*
	* Hardware monitoring driver for UCD90xxx Sequencer and System Health
	* Controller series
	*
	* Copyright (C) 2011 Ericsson AB.
	*/

	#include <linux/debugfs.h>
	#include <linux/kernel.h>
	#include <linux/module.h>
	#include <linux/of_device.h>
	#include <linux/init.h>
	#include <linux/err.h>
	#include <linux/slab.h>
	#include <linux/i2c.h>
	#include <linux/pmbus.h>
	#include <linux/gpio/driver.h>
	#include "pmbus.h"

	enum chips { ucd9000, ucd90120, ucd90124, ucd90160, ucd90320, ucd9090,
	ucd90910 };

	#define UCD9000_MONITOR_CONFIG 0xd5
	#define UCD9000_NUM_PAGES 0xd6
	#define UCD9000_FAN_CONFIG_INDEX 0xe7
	#define UCD9000_FAN_CONFIG 0xe8
	#define UCD9000_MFR_STATUS 0xf3
	#define UCD9000_GPIO_SELECT 0xfa
	#define UCD9000_GPIO_CONFIG 0xfb
	#define UCD9000_DEVICE_ID 0xfd

	/* GPIO CONFIG bits */
	#define UCD9000_GPIO_CONFIG_ENABLE BIT(0)
	#define UCD9000_GPIO_CONFIG_OUT_ENABLE BIT(1)
	#define UCD9000_GPIO_CONFIG_OUT_VALUE BIT(2)
	#define UCD9000_GPIO_CONFIG_STATUS BIT(3)
	#define UCD9000_GPIO_INPUT 0
	#define UCD9000_GPIO_OUTPUT 1

	#define UCD9000_MON_TYPE(x) (((x) >> 5) & 0x07)
	#define UCD9000_MON_PAGE(x) ((x) & 0x1f)

	#define UCD9000_MON_VOLTAGE 1
	#define UCD9000_MON_TEMPERATURE 2
	#define UCD9000_MON_CURRENT 3
	#define UCD9000_MON_VOLTAGE_HW 4

	#define UCD9000_NUM_FAN 4

	#define UCD9000_GPIO_NAME_LEN 16
	#define UCD9090_NUM_GPIOS 23
	#define UCD901XX_NUM_GPIOS 26
	#define UCD90320_NUM_GPIOS 84
	#define UCD90910_NUM_GPIOS 26

	#define UCD9000_DEBUGFS_NAME_LEN 24
	#define UCD9000_GPI_COUNT 8
	#define UCD90320_GPI_COUNT 32

	struct ucd9000_data {
	u8 fan_data[UCD9000_NUM_FAN][I2C_SMBUS_BLOCK_MAX];
	struct pmbus_driver_info info;
	#ifdef CONFIG_GPIOLIB
	struct gpio_chip gpio;
	#endif
	struct dentry *debugfs;
	};
	#define to_ucd9000_data(_info) container_of(_info, struct ucd9000_data, info)

	struct ucd9000_debugfs_entry {
	struct i2c_client *client;
	u8 index;
	};

	static int ucd9000_get_fan_config(struct i2c_client *client, int fan)
	{
	int fan_config = 0;
	struct ucd9000_data *data
	= to_ucd9000_data(pmbus_get_driver_info(client));

	if (data->fan_data[fan][3] & 1)
	fan_config \|= PB_FAN_2_INSTALLED; /* Use lower bit position */

	/* Pulses/revolution */
	fan_config \|= (data->fan_data[fan][3] & 0x06) >> 1;

	return fan_config;
	}

	static int ucd9000_read_byte_data(struct i2c_client *client, int page, int reg)
	{
	int ret = 0;
	int fan_config;

	switch (reg) {
	case PMBUS_FAN_CONFIG_12:
	if (page > 0)
	return -ENXIO;

	ret = ucd9000_get_fan_config(client, 0);
	if (ret < 0)
	return ret;
	fan_config = ret << 4;
	ret = ucd9000_get_fan_config(client, 1);
	if (ret < 0)
	return ret;
	fan_config \|= ret;
	ret = fan_config;
	break;
	case PMBUS_FAN_CONFIG_34:
	if (page > 0)
	return -ENXIO;

	ret = ucd9000_get_fan_config(client, 2);
	if (ret < 0)
	return ret;
	fan_config = ret << 4;
	ret = ucd9000_get_fan_config(client, 3);
	if (ret < 0)
	return ret;
	fan_config \|= ret;
	ret = fan_config;
	break;
	default:
	ret = -ENODATA;
	break;
	}
	return ret;
	}

	static const struct i2c_device_id ucd9000_id[] = {
	{"ucd9000", ucd9000},
	{"ucd90120", ucd90120},
	{"ucd90124", ucd90124},
	{"ucd90160", ucd90160},
	{"ucd90320", ucd90320},
	{"ucd9090", ucd9090},
	{"ucd90910", ucd90910},
	{}
	};
	MODULE_DEVICE_TABLE(i2c, ucd9000_id);

	static const struct of_device_id __maybe_unused ucd9000_of_match[] = {
	{
	.compatible = "ti,ucd9000",
	.data = (void *)ucd9000
	},
	{
	.compatible = "ti,ucd90120",
	.data = (void *)ucd90120
	},
	{
	.compatible = "ti,ucd90124",
	.data = (void *)ucd90124
	},
	{
	.compatible = "ti,ucd90160",
	.data = (void *)ucd90160
	},
	{
	.compatible = "ti,ucd90320",
	.data = (void *)ucd90320
	},
	{
	.compatible = "ti,ucd9090",
	.data = (void *)ucd9090
	},
	{
	.compatible = "ti,ucd90910",
	.data = (void *)ucd90910
	},
	{ },
	};
	MODULE_DEVICE_TABLE(of, ucd9000_of_match);

	#ifdef CONFIG_GPIOLIB
	static int ucd9000_gpio_read_config(struct i2c_client *client,
	unsigned int offset)
	{
	int ret;

	/* No page set required */
	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_SELECT, offset);
	if (ret < 0)
	return ret;

	return i2c_smbus_read_byte_data(client, UCD9000_GPIO_CONFIG);
	}

	static int ucd9000_gpio_get(struct gpio_chip *gc, unsigned int offset)
	{
	struct i2c_client *client = gpiochip_get_data(gc);
	int ret;

	ret = ucd9000_gpio_read_config(client, offset);
	if (ret < 0)
	return ret;

	return !!(ret & UCD9000_GPIO_CONFIG_STATUS);
	}

	static void ucd9000_gpio_set(struct gpio_chip *gc, unsigned int offset,
	int value)
	{
	struct i2c_client *client = gpiochip_get_data(gc);
	int ret;

	ret = ucd9000_gpio_read_config(client, offset);
	if (ret < 0) {
	dev_dbg(&client->dev, "failed to read GPIO %d config: %d\n",
	offset, ret);
	return;
	}

	if (value) {
	if (ret & UCD9000_GPIO_CONFIG_STATUS)
	return;

	ret \|= UCD9000_GPIO_CONFIG_STATUS;
	} else {
	if (!(ret & UCD9000_GPIO_CONFIG_STATUS))
	return;

	ret &= ~UCD9000_GPIO_CONFIG_STATUS;
	}

	ret \|= UCD9000_GPIO_CONFIG_ENABLE;

	/* Page set not required */
	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
	if (ret < 0) {
	dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
	offset, ret);
	return;
	}

	ret &= ~UCD9000_GPIO_CONFIG_ENABLE;

	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, ret);
	if (ret < 0)
	dev_dbg(&client->dev, "Failed to write GPIO %d config: %d\n",
	offset, ret);
	}

	static int ucd9000_gpio_get_direction(struct gpio_chip *gc,
	unsigned int offset)
	{
	struct i2c_client *client = gpiochip_get_data(gc);
	int ret;

	ret = ucd9000_gpio_read_config(client, offset);
	if (ret < 0)
	return ret;

	return !(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE);
	}

	static int ucd9000_gpio_set_direction(struct gpio_chip *gc,
	unsigned int offset, bool direction_out,
	int requested_out)
	{
	struct i2c_client *client = gpiochip_get_data(gc);
	int ret, config, out_val;

	ret = ucd9000_gpio_read_config(client, offset);
	if (ret < 0)
	return ret;

	if (direction_out) {
	out_val = requested_out ? UCD9000_GPIO_CONFIG_OUT_VALUE : 0;

	if (ret & UCD9000_GPIO_CONFIG_OUT_ENABLE) {
	if ((ret & UCD9000_GPIO_CONFIG_OUT_VALUE) == out_val)
	return 0;
	} else {
	ret \|= UCD9000_GPIO_CONFIG_OUT_ENABLE;
	}

	if (out_val)
	ret \|= UCD9000_GPIO_CONFIG_OUT_VALUE;
	else
	ret &= ~UCD9000_GPIO_CONFIG_OUT_VALUE;

	} else {
	if (!(ret & UCD9000_GPIO_CONFIG_OUT_ENABLE))
	return 0;

	ret &= ~UCD9000_GPIO_CONFIG_OUT_ENABLE;
	}

	ret \|= UCD9000_GPIO_CONFIG_ENABLE;
	config = ret;

	/* Page set not required */
	ret = i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
	if (ret < 0)
	return ret;

	config &= ~UCD9000_GPIO_CONFIG_ENABLE;

	return i2c_smbus_write_byte_data(client, UCD9000_GPIO_CONFIG, config);
	}

	static int ucd9000_gpio_direction_input(struct gpio_chip *gc,
	unsigned int offset)
	{
	return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_INPUT, 0);
	}

	static int ucd9000_gpio_direction_output(struct gpio_chip *gc,
	unsigned int offset, int val)
	{
	return ucd9000_gpio_set_direction(gc, offset, UCD9000_GPIO_OUTPUT,
	val);
	}

	static void ucd9000_probe_gpio(struct i2c_client *client,
	const struct i2c_device_id *mid,
	struct ucd9000_data *data)
	{
	int rc;

	switch (mid->driver_data) {
	case ucd9090:
	data->gpio.ngpio = UCD9090_NUM_GPIOS;
	break;
	case ucd90120:
	case ucd90124:
	case ucd90160:
	data->gpio.ngpio = UCD901XX_NUM_GPIOS;
	break;
	case ucd90320:
	data->gpio.ngpio = UCD90320_NUM_GPIOS;
	break;
	case ucd90910:
	data->gpio.ngpio = UCD90910_NUM_GPIOS;
	break;
	default:
	return; /* GPIO support is optional. */
	}

	/*
	* Pinmux support has not been added to the new gpio_chip.
	* This support should be added when possible given the mux
	* behavior of these IO devices.
	*/
	data->gpio.label = client->name;
	data->gpio.get_direction = ucd9000_gpio_get_direction;
	data->gpio.direction_input = ucd9000_gpio_direction_input;
	data->gpio.direction_output = ucd9000_gpio_direction_output;
	data->gpio.get = ucd9000_gpio_get;
	data->gpio.set = ucd9000_gpio_set;
	data->gpio.can_sleep = true;
	data->gpio.base = -1;
	data->gpio.parent = &client->dev;

	rc = devm_gpiochip_add_data(&client->dev, &data->gpio, client);
	if (rc)
	dev_warn(&client->dev, "Could not add gpiochip: %d\n", rc);
	}
	#else
	static void ucd9000_probe_gpio(struct i2c_client *client,
	const struct i2c_device_id *mid,
	struct ucd9000_data *data)
	{
	}
	#endif /* CONFIG_GPIOLIB */

	#ifdef CONFIG_DEBUG_FS
	static int ucd9000_get_mfr_status(struct i2c_client client, u8 buffer)
	{
	int ret = pmbus_set_page(client, 0, 0xff);

	if (ret < 0)
	return ret;

	return i2c_smbus_read_block_data(client, UCD9000_MFR_STATUS, buffer);
	}

	static int ucd9000_debugfs_show_mfr_status_bit(void data, u64 val)
	{
	struct ucd9000_debugfs_entry *entry = data;
	struct i2c_client *client = entry->client;
	u8 buffer[I2C_SMBUS_BLOCK_MAX];
	int ret, i;

	ret = ucd9000_get_mfr_status(client, buffer);
	if (ret < 0)
	return ret;

	/*
	* GPI fault bits are in sets of 8, two bytes from end of response.
	*/
	i = ret - 3 - entry->index / 8;
	if (i >= 0)
	*val = !!(buffer[i] & BIT(entry->index % 8));

	return 0;
	}
	DEFINE_DEBUGFS_ATTRIBUTE(ucd9000_debugfs_mfr_status_bit,
	ucd9000_debugfs_show_mfr_status_bit, NULL, "%1lld\n");

	static ssize_t ucd9000_debugfs_read_mfr_status(struct file *file,
	char __user *buf, size_t count,
	loff_t *ppos)
	{
	struct i2c_client *client = file->private_data;
	u8 buffer[I2C_SMBUS_BLOCK_MAX];
	char str[(I2C_SMBUS_BLOCK_MAX * 2) + 2];
	char *res;
	int rc;

	rc = ucd9000_get_mfr_status(client, buffer);
	if (rc < 0)
	return rc;

	res = bin2hex(str, buffer, min(rc, I2C_SMBUS_BLOCK_MAX));
	*res++ = '\n';
	*res = 0;

	return simple_read_from_buffer(buf, count, ppos, str, res - str);
	}

	static const struct file_operations ucd9000_debugfs_show_mfr_status_fops = {
	.llseek = noop_llseek,
	.read = ucd9000_debugfs_read_mfr_status,
	.open = simple_open,
	};

	static int ucd9000_init_debugfs(struct i2c_client *client,
	const struct i2c_device_id *mid,
	struct ucd9000_data *data)
	{
	struct dentry *debugfs;
	struct ucd9000_debugfs_entry *entries;
	int i, gpi_count;
	char name[UCD9000_DEBUGFS_NAME_LEN];

	debugfs = pmbus_get_debugfs_dir(client);
	if (!debugfs)
	return -ENOENT;

	data->debugfs = debugfs_create_dir(client->name, debugfs);
	if (!data->debugfs)
	return -ENOENT;

	/*
	* Of the chips this driver supports, only the UCD9090, UCD90160,
	* UCD90320, and UCD90910 report GPI faults in their MFR_STATUS
	* register, so only create the GPI fault debugfs attributes for those
	* chips.
	*/
	if (mid->driver_data == ucd9090 \|\| mid->driver_data == ucd90160 \|\|
	mid->driver_data == ucd90320 \|\| mid->driver_data == ucd90910) {
	gpi_count = mid->driver_data == ucd90320 ? UCD90320_GPI_COUNT
	: UCD9000_GPI_COUNT;
	entries = devm_kcalloc(&client->dev,
	gpi_count, sizeof(*entries),
	GFP_KERNEL);
	if (!entries)
	return -ENOMEM;

	for (i = 0; i < gpi_count; i++) {
	entries[i].client = client;
	entries[i].index = i;
	scnprintf(name, UCD9000_DEBUGFS_NAME_LEN,
	"gpi%d_alarm", i + 1);
	debugfs_create_file(name, 0444, data->debugfs,
	&entries[i],
	&ucd9000_debugfs_mfr_status_bit);
	}
	}

	scnprintf(name, UCD9000_DEBUGFS_NAME_LEN, "mfr_status");
	debugfs_create_file(name, 0444, data->debugfs, client,
	&ucd9000_debugfs_show_mfr_status_fops);

	return 0;
	}
	#else
	static int ucd9000_init_debugfs(struct i2c_client *client,
	const struct i2c_device_id *mid,
	struct ucd9000_data *data)
	{
	return 0;
	}
	#endif /* CONFIG_DEBUG_FS */

	static int ucd9000_probe(struct i2c_client *client)
	{
	u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
	struct ucd9000_data *data;
	struct pmbus_driver_info *info;
	const struct i2c_device_id *mid;
	enum chips chip;
	int i, ret;

	if (!i2c_check_functionality(client->adapter,
	I2C_FUNC_SMBUS_BYTE_DATA \|
	I2C_FUNC_SMBUS_BLOCK_DATA))
	return -ENODEV;

	ret = i2c_smbus_read_block_data(client, UCD9000_DEVICE_ID,
	block_buffer);
	if (ret < 0) {
	dev_err(&client->dev, "Failed to read device ID\n");
	return ret;
	}
	block_buffer[ret] = '\0';
	dev_info(&client->dev, "Device ID %s\n", block_buffer);

	for (mid = ucd9000_id; mid->name[0]; mid++) {
	if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
	break;
	}
	if (!mid->name[0]) {
	dev_err(&client->dev, "Unsupported device\n");
	return -ENODEV;
	}

	if (client->dev.of_node)
	chip = (enum chips)of_device_get_match_data(&client->dev);
	else
	chip = mid->driver_data;

	if (chip != ucd9000 && strcmp(client->name, mid->name) != 0)
	dev_notice(&client->dev,
	"Device mismatch: Configured %s, detected %s\n",
	client->name, mid->name);

	data = devm_kzalloc(&client->dev, sizeof(struct ucd9000_data),
	GFP_KERNEL);
	if (!data)
	return -ENOMEM;
	info = &data->info;

	ret = i2c_smbus_read_byte_data(client, UCD9000_NUM_PAGES);
	if (ret < 0) {
	dev_err(&client->dev,
	"Failed to read number of active pages\n");
	return ret;
	}
	info->pages = ret;
	if (!info->pages) {
	dev_err(&client->dev, "No pages configured\n");
	return -ENODEV;
	}

	/* The internal temperature sensor is always active */
	info->func[0] = PMBUS_HAVE_TEMP;

	/* Everything else is configurable */
	ret = i2c_smbus_read_block_data(client, UCD9000_MONITOR_CONFIG,
	block_buffer);
	if (ret <= 0) {
	dev_err(&client->dev, "Failed to read configuration data\n");
	return -ENODEV;
	}
	for (i = 0; i < ret; i++) {
	int page = UCD9000_MON_PAGE(block_buffer[i]);

	if (page >= info->pages)
	continue;

	switch (UCD9000_MON_TYPE(block_buffer[i])) {
	case UCD9000_MON_VOLTAGE:
	case UCD9000_MON_VOLTAGE_HW:
	info->func[page] \|= PMBUS_HAVE_VOUT
	\| PMBUS_HAVE_STATUS_VOUT;
	break;
	case UCD9000_MON_TEMPERATURE:
	info->func[page] \|= PMBUS_HAVE_TEMP2
	\| PMBUS_HAVE_STATUS_TEMP;
	break;
	case UCD9000_MON_CURRENT:
	info->func[page] \|= PMBUS_HAVE_IOUT
	\| PMBUS_HAVE_STATUS_IOUT;
	break;
	default:
	break;
	}
	}

	/* Fan configuration */
	if (mid->driver_data == ucd90124) {
	for (i = 0; i < UCD9000_NUM_FAN; i++) {
	i2c_smbus_write_byte_data(client,
	UCD9000_FAN_CONFIG_INDEX, i);
	ret = i2c_smbus_read_block_data(client,
	UCD9000_FAN_CONFIG,
	data->fan_data[i]);
	if (ret < 0)
	return ret;
	}
	i2c_smbus_write_byte_data(client, UCD9000_FAN_CONFIG_INDEX, 0);

	info->read_byte_data = ucd9000_read_byte_data;
	info->func[0] \|= PMBUS_HAVE_FAN12 \| PMBUS_HAVE_STATUS_FAN12
	\| PMBUS_HAVE_FAN34 \| PMBUS_HAVE_STATUS_FAN34;
	}

	ucd9000_probe_gpio(client, mid, data);

	ret = pmbus_do_probe(client, info);
	if (ret)
	return ret;

	ret = ucd9000_init_debugfs(client, mid, data);
	if (ret)
	dev_warn(&client->dev, "Failed to register debugfs: %d\n",
	ret);

	return 0;
	}

	/* This is the driver that will be inserted */
	static struct i2c_driver ucd9000_driver = {
	.driver = {
	.name = "ucd9000",
	.of_match_table = of_match_ptr(ucd9000_of_match),
	},
	.probe_new = ucd9000_probe,
	.remove = pmbus_do_remove,
	.id_table = ucd9000_id,
	};

	module_i2c_driver(ucd9000_driver);

	MODULE_AUTHOR("Guenter Roeck");
	MODULE_DESCRIPTION("PMBus driver for TI UCD90xxx");
	MODULE_LICENSE("GPL");