| // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause |
| /* |
| * PWM controller driver for Amlogic Meson SoCs. |
| * |
| * This PWM is only a set of Gates, Dividers and Counters: |
| * PWM output is achieved by calculating a clock that permits calculating |
| * two periods (low and high). The counter then has to be set to switch after |
| * N cycles for the first half period. |
| * The hardware has no "polarity" setting. This driver reverses the period |
| * cycles (the low length is inverted with the high length) for |
| * PWM_POLARITY_INVERSED. This means that .get_state cannot read the polarity |
| * from the hardware. |
| * Setting the duty cycle will disable and re-enable the PWM output. |
| * Disabling the PWM stops the output immediately (without waiting for the |
| * current period to complete first). |
| * |
| * The public S912 (GXM) datasheet contains some documentation for this PWM |
| * controller starting on page 543: |
| * https://dl.khadas.com/Hardware/VIM2/Datasheet/S912_Datasheet_V0.220170314publicversion-Wesion.pdf |
| * An updated version of this IP block is found in S922X (G12B) SoCs. The |
| * datasheet contains the description for this IP block revision starting at |
| * page 1084: |
| * https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf |
| * |
| * Copyright (c) 2016 BayLibre, SAS. |
| * Author: Neil Armstrong <narmstrong@baylibre.com> |
| * Copyright (C) 2014 Amlogic, Inc. |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/err.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/math64.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/pwm.h> |
| #include <linux/slab.h> |
| #include <linux/spinlock.h> |
| |
| #define REG_PWM_A 0x0 |
| #define REG_PWM_B 0x4 |
| #define PWM_LOW_MASK GENMASK(15, 0) |
| #define PWM_HIGH_MASK GENMASK(31, 16) |
| |
| #define REG_MISC_AB 0x8 |
| #define MISC_B_CLK_EN BIT(23) |
| #define MISC_A_CLK_EN BIT(15) |
| #define MISC_CLK_DIV_MASK 0x7f |
| #define MISC_B_CLK_DIV_SHIFT 16 |
| #define MISC_A_CLK_DIV_SHIFT 8 |
| #define MISC_B_CLK_SEL_SHIFT 6 |
| #define MISC_A_CLK_SEL_SHIFT 4 |
| #define MISC_CLK_SEL_MASK 0x3 |
| #define MISC_B_EN BIT(1) |
| #define MISC_A_EN BIT(0) |
| |
| #define MESON_NUM_PWMS 2 |
| |
| static struct meson_pwm_channel_data { |
| u8 reg_offset; |
| u8 clk_sel_shift; |
| u8 clk_div_shift; |
| u32 clk_en_mask; |
| u32 pwm_en_mask; |
| } meson_pwm_per_channel_data[MESON_NUM_PWMS] = { |
| { |
| .reg_offset = REG_PWM_A, |
| .clk_sel_shift = MISC_A_CLK_SEL_SHIFT, |
| .clk_div_shift = MISC_A_CLK_DIV_SHIFT, |
| .clk_en_mask = MISC_A_CLK_EN, |
| .pwm_en_mask = MISC_A_EN, |
| }, |
| { |
| .reg_offset = REG_PWM_B, |
| .clk_sel_shift = MISC_B_CLK_SEL_SHIFT, |
| .clk_div_shift = MISC_B_CLK_DIV_SHIFT, |
| .clk_en_mask = MISC_B_CLK_EN, |
| .pwm_en_mask = MISC_B_EN, |
| } |
| }; |
| |
| struct meson_pwm_channel { |
| unsigned int hi; |
| unsigned int lo; |
| u8 pre_div; |
| |
| struct clk *clk_parent; |
| struct clk_mux mux; |
| struct clk *clk; |
| }; |
| |
| struct meson_pwm_data { |
| const char * const *parent_names; |
| unsigned int num_parents; |
| }; |
| |
| struct meson_pwm { |
| struct pwm_chip chip; |
| const struct meson_pwm_data *data; |
| struct meson_pwm_channel channels[MESON_NUM_PWMS]; |
| void __iomem *base; |
| /* |
| * Protects register (write) access to the REG_MISC_AB register |
| * that is shared between the two PWMs. |
| */ |
| spinlock_t lock; |
| }; |
| |
| static inline struct meson_pwm *to_meson_pwm(struct pwm_chip *chip) |
| { |
| return container_of(chip, struct meson_pwm, chip); |
| } |
| |
| static int meson_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm) |
| { |
| struct meson_pwm *meson = to_meson_pwm(chip); |
| struct meson_pwm_channel *channel; |
| struct device *dev = chip->dev; |
| int err; |
| |
| channel = pwm_get_chip_data(pwm); |
| if (channel) |
| return 0; |
| |
| channel = &meson->channels[pwm->hwpwm]; |
| |
| if (channel->clk_parent) { |
| err = clk_set_parent(channel->clk, channel->clk_parent); |
| if (err < 0) { |
| dev_err(dev, "failed to set parent %s for %s: %d\n", |
| __clk_get_name(channel->clk_parent), |
| __clk_get_name(channel->clk), err); |
| return err; |
| } |
| } |
| |
| err = clk_prepare_enable(channel->clk); |
| if (err < 0) { |
| dev_err(dev, "failed to enable clock %s: %d\n", |
| __clk_get_name(channel->clk), err); |
| return err; |
| } |
| |
| return pwm_set_chip_data(pwm, channel); |
| } |
| |
| static void meson_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm) |
| { |
| struct meson_pwm_channel *channel = pwm_get_chip_data(pwm); |
| |
| if (channel) |
| clk_disable_unprepare(channel->clk); |
| } |
| |
| static int meson_pwm_calc(struct meson_pwm *meson, struct pwm_device *pwm, |
| const struct pwm_state *state) |
| { |
| struct meson_pwm_channel *channel = pwm_get_chip_data(pwm); |
| unsigned int duty, period, pre_div, cnt, duty_cnt; |
| unsigned long fin_freq; |
| |
| duty = state->duty_cycle; |
| period = state->period; |
| |
| if (state->polarity == PWM_POLARITY_INVERSED) |
| duty = period - duty; |
| |
| fin_freq = clk_get_rate(channel->clk); |
| if (fin_freq == 0) { |
| dev_err(meson->chip.dev, "invalid source clock frequency\n"); |
| return -EINVAL; |
| } |
| |
| dev_dbg(meson->chip.dev, "fin_freq: %lu Hz\n", fin_freq); |
| |
| pre_div = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * 0xffffLL); |
| if (pre_div > MISC_CLK_DIV_MASK) { |
| dev_err(meson->chip.dev, "unable to get period pre_div\n"); |
| return -EINVAL; |
| } |
| |
| cnt = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * (pre_div + 1)); |
| if (cnt > 0xffff) { |
| dev_err(meson->chip.dev, "unable to get period cnt\n"); |
| return -EINVAL; |
| } |
| |
| dev_dbg(meson->chip.dev, "period=%u pre_div=%u cnt=%u\n", period, |
| pre_div, cnt); |
| |
| if (duty == period) { |
| channel->pre_div = pre_div; |
| channel->hi = cnt; |
| channel->lo = 0; |
| } else if (duty == 0) { |
| channel->pre_div = pre_div; |
| channel->hi = 0; |
| channel->lo = cnt; |
| } else { |
| /* Then check is we can have the duty with the same pre_div */ |
| duty_cnt = div64_u64(fin_freq * (u64)duty, |
| NSEC_PER_SEC * (pre_div + 1)); |
| if (duty_cnt > 0xffff) { |
| dev_err(meson->chip.dev, "unable to get duty cycle\n"); |
| return -EINVAL; |
| } |
| |
| dev_dbg(meson->chip.dev, "duty=%u pre_div=%u duty_cnt=%u\n", |
| duty, pre_div, duty_cnt); |
| |
| channel->pre_div = pre_div; |
| channel->hi = duty_cnt; |
| channel->lo = cnt - duty_cnt; |
| } |
| |
| return 0; |
| } |
| |
| static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm) |
| { |
| struct meson_pwm_channel *channel = pwm_get_chip_data(pwm); |
| struct meson_pwm_channel_data *channel_data; |
| unsigned long flags; |
| u32 value; |
| |
| channel_data = &meson_pwm_per_channel_data[pwm->hwpwm]; |
| |
| spin_lock_irqsave(&meson->lock, flags); |
| |
| value = readl(meson->base + REG_MISC_AB); |
| value &= ~(MISC_CLK_DIV_MASK << channel_data->clk_div_shift); |
| value |= channel->pre_div << channel_data->clk_div_shift; |
| value |= channel_data->clk_en_mask; |
| writel(value, meson->base + REG_MISC_AB); |
| |
| value = FIELD_PREP(PWM_HIGH_MASK, channel->hi) | |
| FIELD_PREP(PWM_LOW_MASK, channel->lo); |
| writel(value, meson->base + channel_data->reg_offset); |
| |
| value = readl(meson->base + REG_MISC_AB); |
| value |= channel_data->pwm_en_mask; |
| writel(value, meson->base + REG_MISC_AB); |
| |
| spin_unlock_irqrestore(&meson->lock, flags); |
| } |
| |
| static void meson_pwm_disable(struct meson_pwm *meson, struct pwm_device *pwm) |
| { |
| unsigned long flags; |
| u32 value; |
| |
| spin_lock_irqsave(&meson->lock, flags); |
| |
| value = readl(meson->base + REG_MISC_AB); |
| value &= ~meson_pwm_per_channel_data[pwm->hwpwm].pwm_en_mask; |
| writel(value, meson->base + REG_MISC_AB); |
| |
| spin_unlock_irqrestore(&meson->lock, flags); |
| } |
| |
| static int meson_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, |
| const struct pwm_state *state) |
| { |
| struct meson_pwm_channel *channel = pwm_get_chip_data(pwm); |
| struct meson_pwm *meson = to_meson_pwm(chip); |
| int err = 0; |
| |
| if (!state) |
| return -EINVAL; |
| |
| if (!state->enabled) { |
| if (state->polarity == PWM_POLARITY_INVERSED) { |
| /* |
| * This IP block revision doesn't have an "always high" |
| * setting which we can use for "inverted disabled". |
| * Instead we achieve this using the same settings |
| * that we use a pre_div of 0 (to get the shortest |
| * possible duration for one "count") and |
| * "period == duty_cycle". This results in a signal |
| * which is LOW for one "count", while being HIGH for |
| * the rest of the (so the signal is HIGH for slightly |
| * less than 100% of the period, but this is the best |
| * we can achieve). |
| */ |
| channel->pre_div = 0; |
| channel->hi = ~0; |
| channel->lo = 0; |
| |
| meson_pwm_enable(meson, pwm); |
| } else { |
| meson_pwm_disable(meson, pwm); |
| } |
| } else { |
| err = meson_pwm_calc(meson, pwm, state); |
| if (err < 0) |
| return err; |
| |
| meson_pwm_enable(meson, pwm); |
| } |
| |
| return 0; |
| } |
| |
| static unsigned int meson_pwm_cnt_to_ns(struct pwm_chip *chip, |
| struct pwm_device *pwm, u32 cnt) |
| { |
| struct meson_pwm *meson = to_meson_pwm(chip); |
| struct meson_pwm_channel *channel; |
| unsigned long fin_freq; |
| u32 fin_ns; |
| |
| /* to_meson_pwm() can only be used after .get_state() is called */ |
| channel = &meson->channels[pwm->hwpwm]; |
| |
| fin_freq = clk_get_rate(channel->clk); |
| if (fin_freq == 0) |
| return 0; |
| |
| fin_ns = div_u64(NSEC_PER_SEC, fin_freq); |
| |
| return cnt * fin_ns * (channel->pre_div + 1); |
| } |
| |
| static void meson_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm, |
| struct pwm_state *state) |
| { |
| struct meson_pwm *meson = to_meson_pwm(chip); |
| struct meson_pwm_channel_data *channel_data; |
| struct meson_pwm_channel *channel; |
| u32 value, tmp; |
| |
| if (!state) |
| return; |
| |
| channel = &meson->channels[pwm->hwpwm]; |
| channel_data = &meson_pwm_per_channel_data[pwm->hwpwm]; |
| |
| value = readl(meson->base + REG_MISC_AB); |
| |
| tmp = channel_data->pwm_en_mask | channel_data->clk_en_mask; |
| state->enabled = (value & tmp) == tmp; |
| |
| tmp = value >> channel_data->clk_div_shift; |
| channel->pre_div = FIELD_GET(MISC_CLK_DIV_MASK, tmp); |
| |
| value = readl(meson->base + channel_data->reg_offset); |
| |
| channel->lo = FIELD_GET(PWM_LOW_MASK, value); |
| channel->hi = FIELD_GET(PWM_HIGH_MASK, value); |
| |
| if (channel->lo == 0) { |
| state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->hi); |
| state->duty_cycle = state->period; |
| } else if (channel->lo >= channel->hi) { |
| state->period = meson_pwm_cnt_to_ns(chip, pwm, |
| channel->lo + channel->hi); |
| state->duty_cycle = meson_pwm_cnt_to_ns(chip, pwm, |
| channel->hi); |
| } else { |
| state->period = 0; |
| state->duty_cycle = 0; |
| } |
| } |
| |
| static const struct pwm_ops meson_pwm_ops = { |
| .request = meson_pwm_request, |
| .free = meson_pwm_free, |
| .apply = meson_pwm_apply, |
| .get_state = meson_pwm_get_state, |
| .owner = THIS_MODULE, |
| }; |
| |
| static const char * const pwm_meson8b_parent_names[] = { |
| "xtal", "vid_pll", "fclk_div4", "fclk_div3" |
| }; |
| |
| static const struct meson_pwm_data pwm_meson8b_data = { |
| .parent_names = pwm_meson8b_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_meson8b_parent_names), |
| }; |
| |
| static const char * const pwm_gxbb_parent_names[] = { |
| "xtal", "hdmi_pll", "fclk_div4", "fclk_div3" |
| }; |
| |
| static const struct meson_pwm_data pwm_gxbb_data = { |
| .parent_names = pwm_gxbb_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_gxbb_parent_names), |
| }; |
| |
| /* |
| * Only the 2 first inputs of the GXBB AO PWMs are valid |
| * The last 2 are grounded |
| */ |
| static const char * const pwm_gxbb_ao_parent_names[] = { |
| "xtal", "clk81" |
| }; |
| |
| static const struct meson_pwm_data pwm_gxbb_ao_data = { |
| .parent_names = pwm_gxbb_ao_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_gxbb_ao_parent_names), |
| }; |
| |
| static const char * const pwm_axg_ee_parent_names[] = { |
| "xtal", "fclk_div5", "fclk_div4", "fclk_div3" |
| }; |
| |
| static const struct meson_pwm_data pwm_axg_ee_data = { |
| .parent_names = pwm_axg_ee_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_axg_ee_parent_names), |
| }; |
| |
| static const char * const pwm_axg_ao_parent_names[] = { |
| "aoclk81", "xtal", "fclk_div4", "fclk_div5" |
| }; |
| |
| static const struct meson_pwm_data pwm_axg_ao_data = { |
| .parent_names = pwm_axg_ao_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_axg_ao_parent_names), |
| }; |
| |
| static const char * const pwm_g12a_ao_ab_parent_names[] = { |
| "xtal", "aoclk81", "fclk_div4", "fclk_div5" |
| }; |
| |
| static const struct meson_pwm_data pwm_g12a_ao_ab_data = { |
| .parent_names = pwm_g12a_ao_ab_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_g12a_ao_ab_parent_names), |
| }; |
| |
| static const char * const pwm_g12a_ao_cd_parent_names[] = { |
| "xtal", "aoclk81", |
| }; |
| |
| static const struct meson_pwm_data pwm_g12a_ao_cd_data = { |
| .parent_names = pwm_g12a_ao_cd_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_g12a_ao_cd_parent_names), |
| }; |
| |
| static const char * const pwm_g12a_ee_parent_names[] = { |
| "xtal", "hdmi_pll", "fclk_div4", "fclk_div3" |
| }; |
| |
| static const struct meson_pwm_data pwm_g12a_ee_data = { |
| .parent_names = pwm_g12a_ee_parent_names, |
| .num_parents = ARRAY_SIZE(pwm_g12a_ee_parent_names), |
| }; |
| |
| static const struct of_device_id meson_pwm_matches[] = { |
| { |
| .compatible = "amlogic,meson8b-pwm", |
| .data = &pwm_meson8b_data |
| }, |
| { |
| .compatible = "amlogic,meson-gxbb-pwm", |
| .data = &pwm_gxbb_data |
| }, |
| { |
| .compatible = "amlogic,meson-gxbb-ao-pwm", |
| .data = &pwm_gxbb_ao_data |
| }, |
| { |
| .compatible = "amlogic,meson-axg-ee-pwm", |
| .data = &pwm_axg_ee_data |
| }, |
| { |
| .compatible = "amlogic,meson-axg-ao-pwm", |
| .data = &pwm_axg_ao_data |
| }, |
| { |
| .compatible = "amlogic,meson-g12a-ee-pwm", |
| .data = &pwm_g12a_ee_data |
| }, |
| { |
| .compatible = "amlogic,meson-g12a-ao-pwm-ab", |
| .data = &pwm_g12a_ao_ab_data |
| }, |
| { |
| .compatible = "amlogic,meson-g12a-ao-pwm-cd", |
| .data = &pwm_g12a_ao_cd_data |
| }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, meson_pwm_matches); |
| |
| static int meson_pwm_init_channels(struct meson_pwm *meson) |
| { |
| struct device *dev = meson->chip.dev; |
| struct clk_init_data init; |
| unsigned int i; |
| char name[255]; |
| int err; |
| |
| for (i = 0; i < meson->chip.npwm; i++) { |
| struct meson_pwm_channel *channel = &meson->channels[i]; |
| |
| snprintf(name, sizeof(name), "%s#mux%u", dev_name(dev), i); |
| |
| init.name = name; |
| init.ops = &clk_mux_ops; |
| init.flags = 0; |
| init.parent_names = meson->data->parent_names; |
| init.num_parents = meson->data->num_parents; |
| |
| channel->mux.reg = meson->base + REG_MISC_AB; |
| channel->mux.shift = |
| meson_pwm_per_channel_data[i].clk_sel_shift; |
| channel->mux.mask = MISC_CLK_SEL_MASK; |
| channel->mux.flags = 0; |
| channel->mux.lock = &meson->lock; |
| channel->mux.table = NULL; |
| channel->mux.hw.init = &init; |
| |
| channel->clk = devm_clk_register(dev, &channel->mux.hw); |
| if (IS_ERR(channel->clk)) { |
| err = PTR_ERR(channel->clk); |
| dev_err(dev, "failed to register %s: %d\n", name, err); |
| return err; |
| } |
| |
| snprintf(name, sizeof(name), "clkin%u", i); |
| |
| channel->clk_parent = devm_clk_get_optional(dev, name); |
| if (IS_ERR(channel->clk_parent)) |
| return PTR_ERR(channel->clk_parent); |
| } |
| |
| return 0; |
| } |
| |
| static int meson_pwm_probe(struct platform_device *pdev) |
| { |
| struct meson_pwm *meson; |
| struct resource *regs; |
| int err; |
| |
| meson = devm_kzalloc(&pdev->dev, sizeof(*meson), GFP_KERNEL); |
| if (!meson) |
| return -ENOMEM; |
| |
| regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| meson->base = devm_ioremap_resource(&pdev->dev, regs); |
| if (IS_ERR(meson->base)) |
| return PTR_ERR(meson->base); |
| |
| spin_lock_init(&meson->lock); |
| meson->chip.dev = &pdev->dev; |
| meson->chip.ops = &meson_pwm_ops; |
| meson->chip.base = -1; |
| meson->chip.npwm = MESON_NUM_PWMS; |
| meson->chip.of_xlate = of_pwm_xlate_with_flags; |
| meson->chip.of_pwm_n_cells = 3; |
| |
| meson->data = of_device_get_match_data(&pdev->dev); |
| |
| err = meson_pwm_init_channels(meson); |
| if (err < 0) |
| return err; |
| |
| err = pwmchip_add(&meson->chip); |
| if (err < 0) { |
| dev_err(&pdev->dev, "failed to register PWM chip: %d\n", err); |
| return err; |
| } |
| |
| platform_set_drvdata(pdev, meson); |
| |
| return 0; |
| } |
| |
| static int meson_pwm_remove(struct platform_device *pdev) |
| { |
| struct meson_pwm *meson = platform_get_drvdata(pdev); |
| |
| return pwmchip_remove(&meson->chip); |
| } |
| |
| static struct platform_driver meson_pwm_driver = { |
| .driver = { |
| .name = "meson-pwm", |
| .of_match_table = meson_pwm_matches, |
| }, |
| .probe = meson_pwm_probe, |
| .remove = meson_pwm_remove, |
| }; |
| module_platform_driver(meson_pwm_driver); |
| |
| MODULE_DESCRIPTION("Amlogic Meson PWM Generator driver"); |
| MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); |
| MODULE_LICENSE("Dual BSD/GPL"); |