| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung Exynos5410 SoC device tree source |
| * |
| * Copyright (c) 2013 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| * |
| * Samsung Exynos5410 SoC device nodes are listed in this file. |
| * Exynos5410 based board files can include this file and provide |
| * values for board specfic bindings. |
| */ |
| |
| #include "exynos54xx.dtsi" |
| #include <dt-bindings/clock/exynos5410.h> |
| #include <dt-bindings/clock/exynos-audss-clk.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| / { |
| compatible = "samsung,exynos5410", "samsung,exynos5"; |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| pinctrl0 = &pinctrl_0; |
| pinctrl1 = &pinctrl_1; |
| pinctrl2 = &pinctrl_2; |
| pinctrl3 = &pinctrl_3; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x0>; |
| clock-frequency = <1600000000>; |
| }; |
| |
| cpu1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x1>; |
| clock-frequency = <1600000000>; |
| }; |
| |
| cpu2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x2>; |
| clock-frequency = <1600000000>; |
| }; |
| |
| cpu3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x3>; |
| clock-frequency = <1600000000>; |
| }; |
| }; |
| |
| soc: soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pmu_system_controller: system-controller@10040000 { |
| compatible = "samsung,exynos5410-pmu", "syscon"; |
| reg = <0x10040000 0x5000>; |
| clock-names = "clkout16"; |
| clocks = <&fin_pll>; |
| #clock-cells = <1>; |
| }; |
| |
| clock: clock-controller@10010000 { |
| compatible = "samsung,exynos5410-clock"; |
| reg = <0x10010000 0x30000>; |
| #clock-cells = <1>; |
| }; |
| |
| clock_audss: audss-clock-controller@3810000 { |
| compatible = "samsung,exynos5410-audss-clock"; |
| reg = <0x03810000 0x0C>; |
| #clock-cells = <1>; |
| clocks = <&fin_pll>, <&clock CLK_FOUT_EPLL>; |
| clock-names = "pll_ref", "pll_in"; |
| }; |
| |
| tmu_cpu0: tmu@10060000 { |
| compatible = "samsung,exynos5420-tmu"; |
| reg = <0x10060000 0x100>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_TMU>; |
| clock-names = "tmu_apbif"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| tmu_cpu1: tmu@10064000 { |
| compatible = "samsung,exynos5420-tmu"; |
| reg = <0x10064000 0x100>; |
| interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_TMU>; |
| clock-names = "tmu_apbif"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| tmu_cpu2: tmu@10068000 { |
| compatible = "samsung,exynos5420-tmu"; |
| reg = <0x10068000 0x100>; |
| interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_TMU>; |
| clock-names = "tmu_apbif"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| tmu_cpu3: tmu@1006c000 { |
| compatible = "samsung,exynos5420-tmu"; |
| reg = <0x1006c000 0x100>; |
| interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_TMU>; |
| clock-names = "tmu_apbif"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| mmc_0: mmc@12200000 { |
| compatible = "samsung,exynos5250-dw-mshc"; |
| reg = <0x12200000 0x1000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>; |
| clock-names = "biu", "ciu"; |
| fifo-depth = <0x80>; |
| status = "disabled"; |
| }; |
| |
| mmc_1: mmc@12210000 { |
| compatible = "samsung,exynos5250-dw-mshc"; |
| reg = <0x12210000 0x1000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>; |
| clock-names = "biu", "ciu"; |
| fifo-depth = <0x80>; |
| status = "disabled"; |
| }; |
| |
| mmc_2: mmc@12220000 { |
| compatible = "samsung,exynos5250-dw-mshc"; |
| reg = <0x12220000 0x1000>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>; |
| clock-names = "biu", "ciu"; |
| fifo-depth = <0x80>; |
| status = "disabled"; |
| }; |
| |
| pinctrl_0: pinctrl@13400000 { |
| compatible = "samsung,exynos5410-pinctrl"; |
| reg = <0x13400000 0x1000>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| |
| wakeup-interrupt-controller { |
| compatible = "samsung,exynos4210-wakeup-eint"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| pinctrl_1: pinctrl@14000000 { |
| compatible = "samsung,exynos5410-pinctrl"; |
| reg = <0x14000000 0x1000>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pinctrl_2: pinctrl@10d10000 { |
| compatible = "samsung,exynos5410-pinctrl"; |
| reg = <0x10d10000 0x1000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pinctrl_3: pinctrl@3860000 { |
| compatible = "samsung,exynos5410-pinctrl"; |
| reg = <0x03860000 0x1000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| pdma0: dma-controller@121a0000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x121a0000 0x1000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_PDMA0>; |
| clock-names = "apb_pclk"; |
| #dma-cells = <1>; |
| #dma-channels = <8>; |
| #dma-requests = <32>; |
| }; |
| |
| pdma1: dma-controller@121b0000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x121b0000 0x1000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clock CLK_PDMA1>; |
| clock-names = "apb_pclk"; |
| #dma-cells = <1>; |
| #dma-channels = <8>; |
| #dma-requests = <32>; |
| }; |
| |
| audi2s0: i2s@3830000 { |
| compatible = "samsung,exynos5420-i2s"; |
| reg = <0x03830000 0x100>; |
| dmas = <&pdma0 10>, |
| <&pdma0 9>, |
| <&pdma0 8>; |
| dma-names = "tx", "rx", "tx-sec"; |
| clocks = <&clock_audss EXYNOS_I2S_BUS>, |
| <&clock_audss EXYNOS_I2S_BUS>, |
| <&clock_audss EXYNOS_SCLK_I2S>; |
| clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; |
| #clock-cells = <1>; |
| clock-output-names = "i2s_cdclk0"; |
| #sound-dai-cells = <1>; |
| samsung,idma-addr = <0x03000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&audi2s0_bus>; |
| status = "disabled"; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu0_thermal: cpu0-thermal { |
| thermal-sensors = <&tmu_cpu0>; |
| #include "exynos5420-trip-points.dtsi" |
| }; |
| cpu1_thermal: cpu1-thermal { |
| thermal-sensors = <&tmu_cpu1>; |
| #include "exynos5420-trip-points.dtsi" |
| }; |
| cpu2_thermal: cpu2-thermal { |
| thermal-sensors = <&tmu_cpu2>; |
| #include "exynos5420-trip-points.dtsi" |
| }; |
| cpu3_thermal: cpu3-thermal { |
| thermal-sensors = <&tmu_cpu3>; |
| #include "exynos5420-trip-points.dtsi" |
| }; |
| }; |
| }; |
| |
| &adc { |
| clocks = <&clock CLK_TSADC>; |
| clock-names = "adc"; |
| samsung,syscon-phandle = <&pmu_system_controller>; |
| }; |
| |
| &arm_a15_pmu { |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| status = "okay"; |
| }; |
| |
| &i2c_0 { |
| clocks = <&clock CLK_I2C0>; |
| clock-names = "i2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_bus>; |
| }; |
| |
| &i2c_1 { |
| clocks = <&clock CLK_I2C1>; |
| clock-names = "i2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_bus>; |
| }; |
| |
| &i2c_2 { |
| clocks = <&clock CLK_I2C2>; |
| clock-names = "i2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_bus>; |
| }; |
| |
| &i2c_3 { |
| clocks = <&clock CLK_I2C3>; |
| clock-names = "i2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_bus>; |
| }; |
| |
| &hsi2c_4 { |
| clocks = <&clock CLK_USI0>; |
| clock-names = "hsi2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c4_hs_bus>; |
| }; |
| |
| &hsi2c_5 { |
| clocks = <&clock CLK_USI1>; |
| clock-names = "hsi2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c5_hs_bus>; |
| }; |
| |
| &hsi2c_6 { |
| clocks = <&clock CLK_USI2>; |
| clock-names = "hsi2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c6_hs_bus>; |
| }; |
| |
| &hsi2c_7 { |
| clocks = <&clock CLK_USI3>; |
| clock-names = "hsi2c"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c7_hs_bus>; |
| }; |
| |
| &mct { |
| clocks = <&fin_pll>, <&clock CLK_MCT>; |
| clock-names = "fin_pll", "mct"; |
| }; |
| |
| &prng { |
| clocks = <&clock CLK_SSS>; |
| clock-names = "secss"; |
| }; |
| |
| &pwm { |
| clocks = <&clock CLK_PWM>; |
| clock-names = "timers"; |
| }; |
| |
| &rtc { |
| clocks = <&clock CLK_RTC>; |
| clock-names = "rtc"; |
| status = "disabled"; |
| }; |
| |
| &serial_0 { |
| clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; |
| clock-names = "uart", "clk_uart_baud0"; |
| dmas = <&pdma0 13>, <&pdma0 14>; |
| dma-names = "rx", "tx"; |
| }; |
| |
| &serial_1 { |
| clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; |
| clock-names = "uart", "clk_uart_baud0"; |
| dmas = <&pdma1 15>, <&pdma1 16>; |
| dma-names = "rx", "tx"; |
| }; |
| |
| &serial_2 { |
| clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; |
| clock-names = "uart", "clk_uart_baud0"; |
| dmas = <&pdma0 15>, <&pdma0 16>; |
| dma-names = "rx", "tx"; |
| }; |
| |
| &serial_3 { |
| clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; |
| clock-names = "uart", "clk_uart_baud0"; |
| dmas = <&pdma1 17>, <&pdma1 18>; |
| dma-names = "rx", "tx"; |
| }; |
| |
| &sss { |
| clocks = <&clock CLK_SSS>; |
| clock-names = "secss"; |
| }; |
| |
| &sromc { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| ranges = <0 0 0x04000000 0x20000 |
| 1 0 0x05000000 0x20000 |
| 2 0 0x06000000 0x20000 |
| 3 0 0x07000000 0x20000>; |
| }; |
| |
| &trng { |
| clocks = <&clock CLK_SSS>; |
| clock-names = "secss"; |
| }; |
| |
| &usbdrd3_0 { |
| clocks = <&clock CLK_USBD300>; |
| clock-names = "usbdrd30"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb3_0_oc>, <&usb3_0_vbusctrl>; |
| }; |
| |
| &usbdrd_phy0 { |
| clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>; |
| clock-names = "phy", "ref"; |
| samsung,pmu-syscon = <&pmu_system_controller>; |
| }; |
| |
| &usbdrd3_1 { |
| clocks = <&clock CLK_USBD301>; |
| clock-names = "usbdrd30"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb3_1_oc>, <&usb3_1_vbusctrl>; |
| }; |
| |
| &usbdrd_dwc3_1 { |
| interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| &usbdrd_phy1 { |
| clocks = <&clock CLK_USBD301>, <&clock CLK_SCLK_USBPHY301>; |
| clock-names = "phy", "ref"; |
| samsung,pmu-syscon = <&pmu_system_controller>; |
| }; |
| |
| &usbhost1 { |
| clocks = <&clock CLK_USBH20>; |
| clock-names = "usbhost"; |
| }; |
| |
| &usbhost2 { |
| clocks = <&clock CLK_USBH20>; |
| clock-names = "usbhost"; |
| }; |
| |
| &usb2_phy { |
| clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>; |
| clock-names = "phy", "ref"; |
| samsung,sysreg-phandle = <&sysreg_system_controller>; |
| samsung,pmureg-phandle = <&pmu_system_controller>; |
| }; |
| |
| &watchdog { |
| clocks = <&clock CLK_WDT>; |
| clock-names = "watchdog"; |
| samsung,syscon-phandle = <&pmu_system_controller>; |
| }; |
| |
| #include "exynos5410-pinctrl.dtsi" |
| #include "exynos-syscon-restart.dtsi" |
