| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2020, The Linux Foundation. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/qcom,gcc-msm8974.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/reset/qcom,gcc-msm8974.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| |
| chosen { }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0>; |
| }; |
| |
| clocks { |
| xo_board: xo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <19200000>; |
| }; |
| |
| sleep_clk: sleep_clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-msm8226", "qcom,scm"; |
| clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>; |
| clock-names = "core", "bus", "iface"; |
| }; |
| }; |
| |
| tcsr_mutex: hwlock { |
| compatible = "qcom,tcsr-mutex"; |
| syscon = <&tcsr_mutex_block 0 0x80>; |
| |
| #hwlock-cells = <1>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| smem_region: smem@3000000 { |
| reg = <0x3000000 0x100000>; |
| no-map; |
| }; |
| }; |
| |
| smd { |
| compatible = "qcom,smd"; |
| |
| rpm { |
| interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; |
| qcom,ipc = <&apcs 8 0>; |
| qcom,smd-edge = <15>; |
| |
| rpm_requests: rpm-requests { |
| compatible = "qcom,rpm-msm8226"; |
| qcom,smd-channels = "rpm_requests"; |
| |
| rpmpd: power-controller { |
| compatible = "qcom,msm8226-rpmpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmpd_opp_table>; |
| |
| rpmpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmpd_opp_ret: opp1 { |
| opp-level = <1>; |
| }; |
| rpmpd_opp_svs_krait: opp2 { |
| opp-level = <2>; |
| }; |
| rpmpd_opp_svs_soc: opp3 { |
| opp-level = <3>; |
| }; |
| rpmpd_opp_nom: opp4 { |
| opp-level = <4>; |
| }; |
| rpmpd_opp_turbo: opp5 { |
| opp-level = <5>; |
| }; |
| rpmpd_opp_super_turbo: opp6 { |
| opp-level = <6>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| smem { |
| compatible = "qcom,smem"; |
| |
| memory-region = <&smem_region>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| soc: soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| intc: interrupt-controller@f9000000 { |
| compatible = "qcom,msm-qgic2"; |
| reg = <0xf9000000 0x1000>, |
| <0xf9002000 0x1000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| }; |
| |
| apcs: syscon@f9011000 { |
| compatible = "syscon"; |
| reg = <0xf9011000 0x1000>; |
| }; |
| |
| sdhc_1: sdhci@f9824900 { |
| compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0xf9824900 0x11c>, <0xf9824000 0x800>; |
| reg-names = "hc_mem", "core_mem"; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| clocks = <&gcc GCC_SDCC1_APPS_CLK>, |
| <&gcc GCC_SDCC1_AHB_CLK>, |
| <&xo_board>; |
| clock-names = "core", "iface", "xo"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc1_default_state>; |
| status = "disabled"; |
| }; |
| |
| sdhc_2: sdhci@f98a4900 { |
| compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>; |
| reg-names = "hc_mem", "core_mem"; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| clocks = <&gcc GCC_SDCC2_APPS_CLK>, |
| <&gcc GCC_SDCC2_AHB_CLK>, |
| <&xo_board>; |
| clock-names = "core", "iface", "xo"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc2_default_state>; |
| status = "disabled"; |
| }; |
| |
| sdhc_3: sdhci@f9864900 { |
| compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0xf9864900 0x11c>, <0xf9864000 0x800>; |
| reg-names = "hc_mem", "core_mem"; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| clocks = <&gcc GCC_SDCC3_APPS_CLK>, |
| <&gcc GCC_SDCC3_AHB_CLK>, |
| <&xo_board>; |
| clock-names = "core", "iface", "xo"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc3_default_state>; |
| status = "disabled"; |
| }; |
| |
| blsp1_uart3: serial@f991f000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0xf991f000 0x1000>; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| blsp1_uart4: serial@f9920000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0xf9920000 0x1000>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| blsp1_i2c1: i2c@f9923000 { |
| status = "disabled"; |
| compatible = "qcom,i2c-qup-v2.1.1"; |
| reg = <0xf9923000 0x1000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_i2c1_pins>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| blsp1_i2c2: i2c@f9924000 { |
| status = "disabled"; |
| compatible = "qcom,i2c-qup-v2.1.1"; |
| reg = <0xf9924000 0x1000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_i2c2_pins>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| blsp1_i2c3: i2c@f9925000 { |
| status = "disabled"; |
| compatible = "qcom,i2c-qup-v2.1.1"; |
| reg = <0xf9925000 0x1000>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_i2c3_pins>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| blsp1_i2c4: i2c@f9926000 { |
| status = "disabled"; |
| compatible = "qcom,i2c-qup-v2.1.1"; |
| reg = <0xf9926000 0x1000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_i2c4_pins>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| blsp1_i2c5: i2c@f9927000 { |
| status = "disabled"; |
| compatible = "qcom,i2c-qup-v2.1.1"; |
| reg = <0xf9927000 0x1000>; |
| interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_i2c5_pins>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| usb: usb@f9a55000 { |
| compatible = "qcom,ci-hdrc"; |
| reg = <0xf9a55000 0x200>, |
| <0xf9a55200 0x200>; |
| interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_USB_HS_AHB_CLK>, |
| <&gcc GCC_USB_HS_SYSTEM_CLK>; |
| clock-names = "iface", "core"; |
| assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>; |
| assigned-clock-rates = <75000000>; |
| resets = <&gcc GCC_USB_HS_BCR>; |
| reset-names = "core"; |
| phy_type = "ulpi"; |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| ahb-burst-config = <0>; |
| phy-names = "usb-phy"; |
| phys = <&usb_hs_phy>; |
| status = "disabled"; |
| #reset-cells = <1>; |
| |
| ulpi { |
| usb_hs_phy: phy { |
| compatible = "qcom,usb-hs-phy-msm8226", |
| "qcom,usb-hs-phy"; |
| #phy-cells = <0>; |
| clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>; |
| clock-names = "ref", "sleep"; |
| resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>; |
| reset-names = "phy", "por"; |
| qcom,init-seq = /bits/ 8 <0x0 0x44 |
| 0x1 0x68 0x2 0x24 0x3 0x13>; |
| }; |
| }; |
| }; |
| |
| gcc: clock-controller@fc400000 { |
| compatible = "qcom,gcc-msm8226"; |
| reg = <0xfc400000 0x4000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| tlmm: pinctrl@fd510000 { |
| compatible = "qcom,msm8226-pinctrl"; |
| reg = <0xfd510000 0x4000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&tlmm 0 0 117>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| |
| blsp1_i2c1_pins: blsp1-i2c1 { |
| pins = "gpio2", "gpio3"; |
| function = "blsp_i2c1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c2_pins: blsp1-i2c2 { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c3_pins: blsp1-i2c3 { |
| pins = "gpio10", "gpio11"; |
| function = "blsp_i2c3"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c4_pins: blsp1-i2c4 { |
| pins = "gpio14", "gpio15"; |
| function = "blsp_i2c4"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c5_pins: blsp1-i2c5 { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_i2c5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdhc1_default_state: sdhc1-default-state { |
| clk { |
| pins = "sdc1_clk"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc2_default_state: sdhc2-default-state { |
| clk { |
| pins = "sdc2_clk"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc3_default_state: sdhc3-default-state { |
| clk { |
| pins = "gpio44"; |
| function = "sdc3"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| cmd { |
| pins = "gpio43"; |
| function = "sdc3"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| data { |
| pins = "gpio39", "gpio40", "gpio41", "gpio42"; |
| function = "sdc3"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| restart@fc4ab000 { |
| compatible = "qcom,pshold"; |
| reg = <0xfc4ab000 0x4>; |
| }; |
| |
| spmi_bus: spmi@fc4cf000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg-names = "core", "intr", "cnfg"; |
| reg = <0xfc4cf000 0x1000>, |
| <0xfc4cb000 0x1000>, |
| <0xfc4ca000 0x1000>; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| rng@f9bff000 { |
| compatible = "qcom,prng"; |
| reg = <0xf9bff000 0x200>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| timer@f9020000 { |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0xf9020000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| frame@f9021000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9021000 0x1000>, |
| <0xf9022000 0x1000>; |
| }; |
| |
| frame@f9023000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9023000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9024000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9024000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9025000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9025000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9026000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9026000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9027000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9027000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@f9028000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0xf9028000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| rpm_msg_ram: memory@fc428000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0xfc428000 0x4000>; |
| }; |
| |
| tcsr_mutex_block: syscon@fd484000 { |
| compatible = "syscon"; |
| reg = <0xfd484000 0x2000>; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 2 |
| (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 |
| (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 4 |
| (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 1 |
| (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| }; |
