| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2012 by Alan Stern | |
| */ | |
| /* This file is part of ehci-hcd.c */ | |
| /*-------------------------------------------------------------------------*/ | |
| /* Set a bit in the USBCMD register */ | |
| static void ehci_set_command_bit(struct ehci_hcd *ehci, u32 bit) | |
| { | |
| ehci->command |= bit; | |
| ehci_writel(ehci, ehci->command, &ehci->regs->command); | |
| /* unblock posted write */ | |
| ehci_readl(ehci, &ehci->regs->command); | |
| } | |
| /* Clear a bit in the USBCMD register */ | |
| static void ehci_clear_command_bit(struct ehci_hcd *ehci, u32 bit) | |
| { | |
| ehci->command &= ~bit; | |
| ehci_writel(ehci, ehci->command, &ehci->regs->command); | |
| /* unblock posted write */ | |
| ehci_readl(ehci, &ehci->regs->command); | |
| } | |
| /*-------------------------------------------------------------------------*/ | |
| /* | |
| * EHCI timer support... Now using hrtimers. | |
| * | |
| * Lots of different events are triggered from ehci->hrtimer. Whenever | |
| * the timer routine runs, it checks each possible event; events that are | |
| * currently enabled and whose expiration time has passed get handled. | |
| * The set of enabled events is stored as a collection of bitflags in | |
| * ehci->enabled_hrtimer_events, and they are numbered in order of | |
| * increasing delay values (ranging between 1 ms and 100 ms). | |
| * | |
| * Rather than implementing a sorted list or tree of all pending events, | |
| * we keep track only of the lowest-numbered pending event, in | |
| * ehci->next_hrtimer_event. Whenever ehci->hrtimer gets restarted, its | |
| * expiration time is set to the timeout value for this event. | |
| * | |
| * As a result, events might not get handled right away; the actual delay | |
| * could be anywhere up to twice the requested delay. This doesn't | |
| * matter, because none of the events are especially time-critical. The | |
| * ones that matter most all have a delay of 1 ms, so they will be | |
| * handled after 2 ms at most, which is okay. In addition to this, we | |
| * allow for an expiration range of 1 ms. | |
| */ | |
| /* | |
| * Delay lengths for the hrtimer event types. | |
| * Keep this list sorted by delay length, in the same order as | |
| * the event types indexed by enum ehci_hrtimer_event in ehci.h. | |
| */ | |
| static unsigned event_delays_ns[] = { | |
| 1 * NSEC_PER_MSEC, /* EHCI_HRTIMER_POLL_ASS */ | |
| 1 * NSEC_PER_MSEC, /* EHCI_HRTIMER_POLL_PSS */ | |
| 1 * NSEC_PER_MSEC, /* EHCI_HRTIMER_POLL_DEAD */ | |
| 1125 * NSEC_PER_USEC, /* EHCI_HRTIMER_UNLINK_INTR */ | |
| 2 * NSEC_PER_MSEC, /* EHCI_HRTIMER_FREE_ITDS */ | |
| 2 * NSEC_PER_MSEC, /* EHCI_HRTIMER_ACTIVE_UNLINK */ | |
| 5 * NSEC_PER_MSEC, /* EHCI_HRTIMER_START_UNLINK_INTR */ | |
| 6 * NSEC_PER_MSEC, /* EHCI_HRTIMER_ASYNC_UNLINKS */ | |
| 10 * NSEC_PER_MSEC, /* EHCI_HRTIMER_IAA_WATCHDOG */ | |
| 10 * NSEC_PER_MSEC, /* EHCI_HRTIMER_DISABLE_PERIODIC */ | |
| 15 * NSEC_PER_MSEC, /* EHCI_HRTIMER_DISABLE_ASYNC */ | |
| 100 * NSEC_PER_MSEC, /* EHCI_HRTIMER_IO_WATCHDOG */ | |
| }; | |
| /* Enable a pending hrtimer event */ | |
| static void ehci_enable_event(struct ehci_hcd *ehci, unsigned event, | |
| bool resched) | |
| { | |
| ktime_t *timeout = &ehci->hr_timeouts[event]; | |
| if (resched) | |
| *timeout = ktime_add(ktime_get(), event_delays_ns[event]); | |
| ehci->enabled_hrtimer_events |= (1 << event); | |
| /* Track only the lowest-numbered pending event */ | |
| if (event < ehci->next_hrtimer_event) { | |
| ehci->next_hrtimer_event = event; | |
| hrtimer_start_range_ns(&ehci->hrtimer, *timeout, | |
| NSEC_PER_MSEC, HRTIMER_MODE_ABS); | |
| } | |
| } | |
| /* Poll the STS_ASS status bit; see when it agrees with CMD_ASE */ | |
| static void ehci_poll_ASS(struct ehci_hcd *ehci) | |
| { | |
| unsigned actual, want; | |
| /* Don't enable anything if the controller isn't running (e.g., died) */ | |
| if (ehci->rh_state != EHCI_RH_RUNNING) | |
| return; | |
| want = (ehci->command & CMD_ASE) ? STS_ASS : 0; | |
| actual = ehci_readl(ehci, &ehci->regs->status) & STS_ASS; | |
| if (want != actual) { | |
| /* Poll again later, but give up after about 2-4 ms */ | |
| if (ehci->ASS_poll_count++ < 2) { | |
| ehci_enable_event(ehci, EHCI_HRTIMER_POLL_ASS, true); | |
| return; | |
| } | |
| ehci_dbg(ehci, "Waited too long for the async schedule status (%x/%x), giving up\n", | |
| want, actual); | |
| } | |
| ehci->ASS_poll_count = 0; | |
| /* The status is up-to-date; restart or stop the schedule as needed */ | |
| if (want == 0) { /* Stopped */ | |
| if (ehci->async_count > 0) | |
| ehci_set_command_bit(ehci, CMD_ASE); | |
| } else { /* Running */ | |
| if (ehci->async_count == 0) { | |
| /* Turn off the schedule after a while */ | |
| ehci_enable_event(ehci, EHCI_HRTIMER_DISABLE_ASYNC, | |
| true); | |
| } | |
| } | |
| } | |
| /* Turn off the async schedule after a brief delay */ | |
| static void ehci_disable_ASE(struct ehci_hcd *ehci) | |
| { | |
| ehci_clear_command_bit(ehci, CMD_ASE); | |
| } | |
| /* Poll the STS_PSS status bit; see when it agrees with CMD_PSE */ | |
| static void ehci_poll_PSS(struct ehci_hcd *ehci) | |
| { | |
| unsigned actual, want; | |
| /* Don't do anything if the controller isn't running (e.g., died) */ | |
| if (ehci->rh_state != EHCI_RH_RUNNING) | |
| return; | |
| want = (ehci->command & CMD_PSE) ? STS_PSS : 0; | |
| actual = ehci_readl(ehci, &ehci->regs->status) & STS_PSS; | |
| if (want != actual) { | |
| /* Poll again later, but give up after about 2-4 ms */ | |
| if (ehci->PSS_poll_count++ < 2) { | |
| ehci_enable_event(ehci, EHCI_HRTIMER_POLL_PSS, true); | |
| return; | |
| } | |
| ehci_dbg(ehci, "Waited too long for the periodic schedule status (%x/%x), giving up\n", | |
| want, actual); | |
| } | |
| ehci->PSS_poll_count = 0; | |
| /* The status is up-to-date; restart or stop the schedule as needed */ | |
| if (want == 0) { /* Stopped */ | |
| if (ehci->periodic_count > 0) | |
| ehci_set_command_bit(ehci, CMD_PSE); | |
| } else { /* Running */ | |
| if (ehci->periodic_count == 0) { | |
| /* Turn off the schedule after a while */ | |
| ehci_enable_event(ehci, EHCI_HRTIMER_DISABLE_PERIODIC, | |
| true); | |
| } | |
| } | |
| } | |
| /* Turn off the periodic schedule after a brief delay */ | |
| static void ehci_disable_PSE(struct ehci_hcd *ehci) | |
| { | |
| ehci_clear_command_bit(ehci, CMD_PSE); | |
| } | |
| /* Poll the STS_HALT status bit; see when a dead controller stops */ | |
| static void ehci_handle_controller_death(struct ehci_hcd *ehci) | |
| { | |
| if (!(ehci_readl(ehci, &ehci->regs->status) & STS_HALT)) { | |
| /* Give up after a few milliseconds */ | |
| if (ehci->died_poll_count++ < 5) { | |
| /* Try again later */ | |
| ehci_enable_event(ehci, EHCI_HRTIMER_POLL_DEAD, true); | |
| return; | |
| } | |
| ehci_warn(ehci, "Waited too long for the controller to stop, giving up\n"); | |
| } | |
| /* Clean up the mess */ | |
| ehci->rh_state = EHCI_RH_HALTED; | |
| ehci_writel(ehci, 0, &ehci->regs->configured_flag); | |
| ehci_writel(ehci, 0, &ehci->regs->intr_enable); | |
| ehci_work(ehci); | |
| end_unlink_async(ehci); | |
| /* Not in process context, so don't try to reset the controller */ | |
| } | |
| /* start to unlink interrupt QHs */ | |
| static void ehci_handle_start_intr_unlinks(struct ehci_hcd *ehci) | |
| { | |
| bool stopped = (ehci->rh_state < EHCI_RH_RUNNING); | |
| /* | |
| * Process all the QHs on the intr_unlink list that were added | |
| * before the current unlink cycle began. The list is in | |
| * temporal order, so stop when we reach the first entry in the | |
| * current cycle. But if the root hub isn't running then | |
| * process all the QHs on the list. | |
| */ | |
| while (!list_empty(&ehci->intr_unlink_wait)) { | |
| struct ehci_qh *qh; | |
| qh = list_first_entry(&ehci->intr_unlink_wait, | |
| struct ehci_qh, unlink_node); | |
| if (!stopped && (qh->unlink_cycle == | |
| ehci->intr_unlink_wait_cycle)) | |
| break; | |
| list_del_init(&qh->unlink_node); | |
| qh->unlink_reason |= QH_UNLINK_QUEUE_EMPTY; | |
| start_unlink_intr(ehci, qh); | |
| } | |
| /* Handle remaining entries later */ | |
| if (!list_empty(&ehci->intr_unlink_wait)) { | |
| ehci_enable_event(ehci, EHCI_HRTIMER_START_UNLINK_INTR, true); | |
| ++ehci->intr_unlink_wait_cycle; | |
| } | |
| } | |
| /* Handle unlinked interrupt QHs once they are gone from the hardware */ | |
| static void ehci_handle_intr_unlinks(struct ehci_hcd *ehci) | |
| { | |
| bool stopped = (ehci->rh_state < EHCI_RH_RUNNING); | |
| /* | |
| * Process all the QHs on the intr_unlink list that were added | |
| * before the current unlink cycle began. The list is in | |
| * temporal order, so stop when we reach the first entry in the | |
| * current cycle. But if the root hub isn't running then | |
| * process all the QHs on the list. | |
| */ | |
| ehci->intr_unlinking = true; | |
| while (!list_empty(&ehci->intr_unlink)) { | |
| struct ehci_qh *qh; | |
| qh = list_first_entry(&ehci->intr_unlink, struct ehci_qh, | |
| unlink_node); | |
| if (!stopped && qh->unlink_cycle == ehci->intr_unlink_cycle) | |
| break; | |
| list_del_init(&qh->unlink_node); | |
| end_unlink_intr(ehci, qh); | |
| } | |
| /* Handle remaining entries later */ | |
| if (!list_empty(&ehci->intr_unlink)) { | |
| ehci_enable_event(ehci, EHCI_HRTIMER_UNLINK_INTR, true); | |
| ++ehci->intr_unlink_cycle; | |
| } | |
| ehci->intr_unlinking = false; | |
| } | |
| /* Start another free-iTDs/siTDs cycle */ | |
| static void start_free_itds(struct ehci_hcd *ehci) | |
| { | |
| if (!(ehci->enabled_hrtimer_events & BIT(EHCI_HRTIMER_FREE_ITDS))) { | |
| ehci->last_itd_to_free = list_entry( | |
| ehci->cached_itd_list.prev, | |
| struct ehci_itd, itd_list); | |
| ehci->last_sitd_to_free = list_entry( | |
| ehci->cached_sitd_list.prev, | |
| struct ehci_sitd, sitd_list); | |
| ehci_enable_event(ehci, EHCI_HRTIMER_FREE_ITDS, true); | |
| } | |
| } | |
| /* Wait for controller to stop using old iTDs and siTDs */ | |
| static void end_free_itds(struct ehci_hcd *ehci) | |
| { | |
| struct ehci_itd *itd, *n; | |
| struct ehci_sitd *sitd, *sn; | |
| if (ehci->rh_state < EHCI_RH_RUNNING) { | |
| ehci->last_itd_to_free = NULL; | |
| ehci->last_sitd_to_free = NULL; | |
| } | |
| list_for_each_entry_safe(itd, n, &ehci->cached_itd_list, itd_list) { | |
| list_del(&itd->itd_list); | |
| dma_pool_free(ehci->itd_pool, itd, itd->itd_dma); | |
| if (itd == ehci->last_itd_to_free) | |
| break; | |
| } | |
| list_for_each_entry_safe(sitd, sn, &ehci->cached_sitd_list, sitd_list) { | |
| list_del(&sitd->sitd_list); | |
| dma_pool_free(ehci->sitd_pool, sitd, sitd->sitd_dma); | |
| if (sitd == ehci->last_sitd_to_free) | |
| break; | |
| } | |
| if (!list_empty(&ehci->cached_itd_list) || | |
| !list_empty(&ehci->cached_sitd_list)) | |
| start_free_itds(ehci); | |
| } | |
| /* Handle lost (or very late) IAA interrupts */ | |
| static void ehci_iaa_watchdog(struct ehci_hcd *ehci) | |
| { | |
| u32 cmd, status; | |
| /* | |
| * Lost IAA irqs wedge things badly; seen first with a vt8235. | |
| * So we need this watchdog, but must protect it against both | |
| * (a) SMP races against real IAA firing and retriggering, and | |
| * (b) clean HC shutdown, when IAA watchdog was pending. | |
| */ | |
| if (!ehci->iaa_in_progress || ehci->rh_state != EHCI_RH_RUNNING) | |
| return; | |
| /* If we get here, IAA is *REALLY* late. It's barely | |
| * conceivable that the system is so busy that CMD_IAAD | |
| * is still legitimately set, so let's be sure it's | |
| * clear before we read STS_IAA. (The HC should clear | |
| * CMD_IAAD when it sets STS_IAA.) | |
| */ | |
| cmd = ehci_readl(ehci, &ehci->regs->command); | |
| /* | |
| * If IAA is set here it either legitimately triggered | |
| * after the watchdog timer expired (_way_ late, so we'll | |
| * still count it as lost) ... or a silicon erratum: | |
| * - VIA seems to set IAA without triggering the IRQ; | |
| * - IAAD potentially cleared without setting IAA. | |
| */ | |
| status = ehci_readl(ehci, &ehci->regs->status); | |
| if ((status & STS_IAA) || !(cmd & CMD_IAAD)) { | |
| INCR(ehci->stats.lost_iaa); | |
| ehci_writel(ehci, STS_IAA, &ehci->regs->status); | |
| } | |
| ehci_dbg(ehci, "IAA watchdog: status %x cmd %x\n", status, cmd); | |
| end_iaa_cycle(ehci); | |
| } | |
| /* Enable the I/O watchdog, if appropriate */ | |
| static void turn_on_io_watchdog(struct ehci_hcd *ehci) | |
| { | |
| /* Not needed if the controller isn't running or it's already enabled */ | |
| if (ehci->rh_state != EHCI_RH_RUNNING || | |
| (ehci->enabled_hrtimer_events & | |
| BIT(EHCI_HRTIMER_IO_WATCHDOG))) | |
| return; | |
| /* | |
| * Isochronous transfers always need the watchdog. | |
| * For other sorts we use it only if the flag is set. | |
| */ | |
| if (ehci->isoc_count > 0 || (ehci->need_io_watchdog && | |
| ehci->async_count + ehci->intr_count > 0)) | |
| ehci_enable_event(ehci, EHCI_HRTIMER_IO_WATCHDOG, true); | |
| } | |
| /* | |
| * Handler functions for the hrtimer event types. | |
| * Keep this array in the same order as the event types indexed by | |
| * enum ehci_hrtimer_event in ehci.h. | |
| */ | |
| static void (*event_handlers[])(struct ehci_hcd *) = { | |
| ehci_poll_ASS, /* EHCI_HRTIMER_POLL_ASS */ | |
| ehci_poll_PSS, /* EHCI_HRTIMER_POLL_PSS */ | |
| ehci_handle_controller_death, /* EHCI_HRTIMER_POLL_DEAD */ | |
| ehci_handle_intr_unlinks, /* EHCI_HRTIMER_UNLINK_INTR */ | |
| end_free_itds, /* EHCI_HRTIMER_FREE_ITDS */ | |
| end_unlink_async, /* EHCI_HRTIMER_ACTIVE_UNLINK */ | |
| ehci_handle_start_intr_unlinks, /* EHCI_HRTIMER_START_UNLINK_INTR */ | |
| unlink_empty_async, /* EHCI_HRTIMER_ASYNC_UNLINKS */ | |
| ehci_iaa_watchdog, /* EHCI_HRTIMER_IAA_WATCHDOG */ | |
| ehci_disable_PSE, /* EHCI_HRTIMER_DISABLE_PERIODIC */ | |
| ehci_disable_ASE, /* EHCI_HRTIMER_DISABLE_ASYNC */ | |
| ehci_work, /* EHCI_HRTIMER_IO_WATCHDOG */ | |
| }; | |
| static enum hrtimer_restart ehci_hrtimer_func(struct hrtimer *t) | |
| { | |
| struct ehci_hcd *ehci = container_of(t, struct ehci_hcd, hrtimer); | |
| ktime_t now; | |
| unsigned long events; | |
| unsigned long flags; | |
| unsigned e; | |
| spin_lock_irqsave(&ehci->lock, flags); | |
| events = ehci->enabled_hrtimer_events; | |
| ehci->enabled_hrtimer_events = 0; | |
| ehci->next_hrtimer_event = EHCI_HRTIMER_NO_EVENT; | |
| /* | |
| * Check each pending event. If its time has expired, handle | |
| * the event; otherwise re-enable it. | |
| */ | |
| now = ktime_get(); | |
| for_each_set_bit(e, &events, EHCI_HRTIMER_NUM_EVENTS) { | |
| if (ktime_compare(now, ehci->hr_timeouts[e]) >= 0) | |
| event_handlers[e](ehci); | |
| else | |
| ehci_enable_event(ehci, e, false); | |
| } | |
| spin_unlock_irqrestore(&ehci->lock, flags); | |
| return HRTIMER_NORESTART; | |
| } |