| # |
| # Phy drivers for Broadcom platforms |
| # |
| config PHY_CYGNUS_PCIE |
| tristate "Broadcom Cygnus PCIe PHY driver" |
| depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST) |
| select GENERIC_PHY |
| default ARCH_BCM_CYGNUS |
| help |
| Enable this to support the Broadcom Cygnus PCIe PHY. |
| If unsure, say N. |
| |
| config PHY_BCM_SR_USB |
| tristate "Broadcom Stingray USB PHY driver" |
| depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST) |
| select GENERIC_PHY |
| default ARCH_BCM_IPROC |
| help |
| Enable this to support the Broadcom Stingray USB PHY |
| driver. It supports all versions of Superspeed and |
| Highspeed PHYs. |
| If unsure, say N. |
| |
| config BCM_KONA_USB2_PHY |
| tristate "Broadcom Kona USB2 PHY Driver" |
| depends on HAS_IOMEM |
| select GENERIC_PHY |
| help |
| Enable this to support the Broadcom Kona USB 2.0 PHY. |
| |
| config PHY_BCM_NS_USB2 |
| tristate "Broadcom Northstar USB 2.0 PHY Driver" |
| depends on ARCH_BCM_IPROC || COMPILE_TEST |
| depends on HAS_IOMEM && OF |
| select GENERIC_PHY |
| help |
| Enable this to support Broadcom USB 2.0 PHY connected to the USB |
| controller on Northstar family. |
| |
| config PHY_BCM_NS_USB3 |
| tristate "Broadcom Northstar USB 3.0 PHY Driver" |
| depends on ARCH_BCM_IPROC || COMPILE_TEST |
| depends on HAS_IOMEM && OF |
| depends on MDIO_BUS |
| select GENERIC_PHY |
| help |
| Enable this to support Broadcom USB 3.0 PHY connected to the USB |
| controller on Northstar family. |
| |
| config PHY_NS2_PCIE |
| tristate "Broadcom Northstar2 PCIe PHY driver" |
| depends on OF && MDIO_BUS_MUX_BCM_IPROC |
| select GENERIC_PHY |
| default ARCH_BCM_IPROC |
| help |
| Enable this to support the Broadcom Northstar2 PCIe PHY. |
| If unsure, say N. |
| |
| config PHY_NS2_USB_DRD |
| tristate "Broadcom Northstar2 USB DRD PHY support" |
| depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST) |
| select GENERIC_PHY |
| select EXTCON |
| default ARCH_BCM_IPROC |
| help |
| Enable this to support the Broadcom Northstar2 USB DRD PHY. |
| This driver initializes the PHY in either HOST or DEVICE mode. |
| The host or device configuration is read from device tree. |
| |
| If unsure, say N. |
| |
| config PHY_BRCM_SATA |
| tristate "Broadcom SATA PHY driver" |
| depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || \ |
| ARCH_BCM_63XX || COMPILE_TEST |
| depends on OF |
| select GENERIC_PHY |
| default ARCH_BCM_IPROC |
| help |
| Enable this to support the Broadcom SATA PHY. |
| If unsure, say N. |
| |
| config PHY_BRCM_USB |
| tristate "Broadcom STB USB PHY driver" |
| depends on ARCH_BRCMSTB |
| depends on OF |
| select GENERIC_PHY |
| select SOC_BRCMSTB |
| default ARCH_BRCMSTB |
| help |
| Enable this to support the Broadcom STB USB PHY. |
| This driver is required by the USB XHCI, EHCI and OHCI |
| drivers. |
| If unsure, say N. |
| |
| config PHY_BCM_SR_PCIE |
| tristate "Broadcom Stingray PCIe PHY driver" |
| depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST) |
| select GENERIC_PHY |
| select MFD_SYSCON |
| default ARCH_BCM_IPROC |
| help |
| Enable this to support the Broadcom Stingray PCIe PHY |
| If unsure, say N. |
