| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright 2018-2020 Broadcom. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/firmware.h> |
| #include <linux/fs.h> |
| #include <linux/idr.h> |
| #include <linux/interrupt.h> |
| #include <linux/panic_notifier.h> |
| #include <linux/kref.h> |
| #include <linux/module.h> |
| #include <linux/mutex.h> |
| #include <linux/pci.h> |
| #include <linux/pci_regs.h> |
| #include <uapi/linux/misc/bcm_vk.h> |
| |
| #include "bcm_vk.h" |
| |
| #define PCI_DEVICE_ID_VALKYRIE 0x5e87 |
| #define PCI_DEVICE_ID_VIPER 0x5e88 |
| |
| static DEFINE_IDA(bcm_vk_ida); |
| |
| enum soc_idx { |
| VALKYRIE_A0 = 0, |
| VALKYRIE_B0, |
| VIPER, |
| VK_IDX_INVALID |
| }; |
| |
| enum img_idx { |
| IMG_PRI = 0, |
| IMG_SEC, |
| IMG_PER_TYPE_MAX |
| }; |
| |
| struct load_image_entry { |
| const u32 image_type; |
| const char *image_name[IMG_PER_TYPE_MAX]; |
| }; |
| |
| #define NUM_BOOT_STAGES 2 |
| /* default firmware images names */ |
| static const struct load_image_entry image_tab[][NUM_BOOT_STAGES] = { |
| [VALKYRIE_A0] = { |
| {VK_IMAGE_TYPE_BOOT1, {"vk_a0-boot1.bin", "vk-boot1.bin"}}, |
| {VK_IMAGE_TYPE_BOOT2, {"vk_a0-boot2.bin", "vk-boot2.bin"}} |
| }, |
| [VALKYRIE_B0] = { |
| {VK_IMAGE_TYPE_BOOT1, {"vk_b0-boot1.bin", "vk-boot1.bin"}}, |
| {VK_IMAGE_TYPE_BOOT2, {"vk_b0-boot2.bin", "vk-boot2.bin"}} |
| }, |
| |
| [VIPER] = { |
| {VK_IMAGE_TYPE_BOOT1, {"vp-boot1.bin", ""}}, |
| {VK_IMAGE_TYPE_BOOT2, {"vp-boot2.bin", ""}} |
| }, |
| }; |
| |
| /* Location of memory base addresses of interest in BAR1 */ |
| /* Load Boot1 to start of ITCM */ |
| #define BAR1_CODEPUSH_BASE_BOOT1 0x100000 |
| |
| /* Allow minimum 1s for Load Image timeout responses */ |
| #define LOAD_IMAGE_TIMEOUT_MS (1 * MSEC_PER_SEC) |
| |
| /* Image startup timeouts */ |
| #define BOOT1_STARTUP_TIMEOUT_MS (5 * MSEC_PER_SEC) |
| #define BOOT2_STARTUP_TIMEOUT_MS (10 * MSEC_PER_SEC) |
| |
| /* 1ms wait for checking the transfer complete status */ |
| #define TXFR_COMPLETE_TIMEOUT_MS 1 |
| |
| /* MSIX usages */ |
| #define VK_MSIX_MSGQ_MAX 3 |
| #define VK_MSIX_NOTF_MAX 1 |
| #define VK_MSIX_TTY_MAX BCM_VK_NUM_TTY |
| #define VK_MSIX_IRQ_MAX (VK_MSIX_MSGQ_MAX + VK_MSIX_NOTF_MAX + \ |
| VK_MSIX_TTY_MAX) |
| #define VK_MSIX_IRQ_MIN_REQ (VK_MSIX_MSGQ_MAX + VK_MSIX_NOTF_MAX) |
| |
| /* Number of bits set in DMA mask*/ |
| #define BCM_VK_DMA_BITS 64 |
| |
| /* Ucode boot wait time */ |
| #define BCM_VK_UCODE_BOOT_US (100 * USEC_PER_MSEC) |
| /* 50% margin */ |
| #define BCM_VK_UCODE_BOOT_MAX_US ((BCM_VK_UCODE_BOOT_US * 3) >> 1) |
| |
| /* deinit time for the card os after receiving doorbell */ |
| #define BCM_VK_DEINIT_TIME_MS (2 * MSEC_PER_SEC) |
| |
| /* |
| * module parameters |
| */ |
| static bool auto_load = true; |
| module_param(auto_load, bool, 0444); |
| MODULE_PARM_DESC(auto_load, |
| "Load images automatically at PCIe probe time.\n"); |
| static uint nr_scratch_pages = VK_BAR1_SCRATCH_DEF_NR_PAGES; |
| module_param(nr_scratch_pages, uint, 0444); |
| MODULE_PARM_DESC(nr_scratch_pages, |
| "Number of pre allocated DMAable coherent pages.\n"); |
| static uint nr_ib_sgl_blk = BCM_VK_DEF_IB_SGL_BLK_LEN; |
| module_param(nr_ib_sgl_blk, uint, 0444); |
| MODULE_PARM_DESC(nr_ib_sgl_blk, |
| "Number of in-band msg blks for short SGL.\n"); |
| |
| /* |
| * alerts that could be generated from peer |
| */ |
| const struct bcm_vk_entry bcm_vk_peer_err[BCM_VK_PEER_ERR_NUM] = { |
| {ERR_LOG_UECC, ERR_LOG_UECC, "uecc"}, |
| {ERR_LOG_SSIM_BUSY, ERR_LOG_SSIM_BUSY, "ssim_busy"}, |
| {ERR_LOG_AFBC_BUSY, ERR_LOG_AFBC_BUSY, "afbc_busy"}, |
| {ERR_LOG_HIGH_TEMP_ERR, ERR_LOG_HIGH_TEMP_ERR, "high_temp"}, |
| {ERR_LOG_WDOG_TIMEOUT, ERR_LOG_WDOG_TIMEOUT, "wdog_timeout"}, |
| {ERR_LOG_SYS_FAULT, ERR_LOG_SYS_FAULT, "sys_fault"}, |
| {ERR_LOG_RAMDUMP, ERR_LOG_RAMDUMP, "ramdump"}, |
| {ERR_LOG_COP_WDOG_TIMEOUT, ERR_LOG_COP_WDOG_TIMEOUT, |
| "cop_wdog_timeout"}, |
| {ERR_LOG_MEM_ALLOC_FAIL, ERR_LOG_MEM_ALLOC_FAIL, "malloc_fail warn"}, |
| {ERR_LOG_LOW_TEMP_WARN, ERR_LOG_LOW_TEMP_WARN, "low_temp warn"}, |
| {ERR_LOG_ECC, ERR_LOG_ECC, "ecc"}, |
| {ERR_LOG_IPC_DWN, ERR_LOG_IPC_DWN, "ipc_down"}, |
| }; |
| |
| /* alerts detected by the host */ |
| const struct bcm_vk_entry bcm_vk_host_err[BCM_VK_HOST_ERR_NUM] = { |
| {ERR_LOG_HOST_PCIE_DWN, ERR_LOG_HOST_PCIE_DWN, "PCIe_down"}, |
| {ERR_LOG_HOST_HB_FAIL, ERR_LOG_HOST_HB_FAIL, "hb_fail"}, |
| {ERR_LOG_HOST_INTF_V_FAIL, ERR_LOG_HOST_INTF_V_FAIL, "intf_ver_fail"}, |
| }; |
| |
| irqreturn_t bcm_vk_notf_irqhandler(int irq, void *dev_id) |
| { |
| struct bcm_vk *vk = dev_id; |
| |
| if (!bcm_vk_drv_access_ok(vk)) { |
| dev_err(&vk->pdev->dev, |
| "Interrupt %d received when msgq not inited\n", irq); |
| goto skip_schedule_work; |
| } |
| |
| /* if notification is not pending, set bit and schedule work */ |
| if (test_and_set_bit(BCM_VK_WQ_NOTF_PEND, vk->wq_offload) == 0) |
| queue_work(vk->wq_thread, &vk->wq_work); |
| |
| skip_schedule_work: |
| return IRQ_HANDLED; |
| } |
| |
| static int bcm_vk_intf_ver_chk(struct bcm_vk *vk) |
| { |
| struct device *dev = &vk->pdev->dev; |
| u32 reg; |
| u16 major, minor; |
| int ret = 0; |
| |
| /* read interface register */ |
| reg = vkread32(vk, BAR_0, BAR_INTF_VER); |
| major = (reg >> BAR_INTF_VER_MAJOR_SHIFT) & BAR_INTF_VER_MASK; |
| minor = reg & BAR_INTF_VER_MASK; |
| |
| /* |
| * if major number is 0, it is pre-release and it would be allowed |
| * to continue, else, check versions accordingly |
| */ |
| if (!major) { |
| dev_warn(dev, "Pre-release major.minor=%d.%d - drv %d.%d\n", |
| major, minor, SEMANTIC_MAJOR, SEMANTIC_MINOR); |
| } else if (major != SEMANTIC_MAJOR) { |
| dev_err(dev, |
| "Intf major.minor=%d.%d rejected - drv %d.%d\n", |
| major, minor, SEMANTIC_MAJOR, SEMANTIC_MINOR); |
| bcm_vk_set_host_alert(vk, ERR_LOG_HOST_INTF_V_FAIL); |
| ret = -EPFNOSUPPORT; |
| } else { |
| dev_dbg(dev, |
| "Intf major.minor=%d.%d passed - drv %d.%d\n", |
| major, minor, SEMANTIC_MAJOR, SEMANTIC_MINOR); |
| } |
| return ret; |
| } |
| |
| static void bcm_vk_log_notf(struct bcm_vk *vk, |
| struct bcm_vk_alert *alert, |
| struct bcm_vk_entry const *entry_tab, |
| const u32 table_size) |
| { |
| u32 i; |
| u32 masked_val, latched_val; |
| struct bcm_vk_entry const *entry; |
| u32 reg; |
| u16 ecc_mem_err, uecc_mem_err; |
| struct device *dev = &vk->pdev->dev; |
| |
| for (i = 0; i < table_size; i++) { |
| entry = &entry_tab[i]; |
| masked_val = entry->mask & alert->notfs; |
| latched_val = entry->mask & alert->flags; |
| |
| if (masked_val == ERR_LOG_UECC) { |
| /* |
| * if there is difference between stored cnt and it |
| * is greater than threshold, log it. |
| */ |
| reg = vkread32(vk, BAR_0, BAR_CARD_ERR_MEM); |
| BCM_VK_EXTRACT_FIELD(uecc_mem_err, reg, |
| BCM_VK_MEM_ERR_FIELD_MASK, |
| BCM_VK_UECC_MEM_ERR_SHIFT); |
| if ((uecc_mem_err != vk->alert_cnts.uecc) && |
| (uecc_mem_err >= BCM_VK_UECC_THRESHOLD)) |
| dev_info(dev, |
| "ALERT! %s.%d uecc RAISED - ErrCnt %d\n", |
| DRV_MODULE_NAME, vk->devid, |
| uecc_mem_err); |
| vk->alert_cnts.uecc = uecc_mem_err; |
| } else if (masked_val == ERR_LOG_ECC) { |
| reg = vkread32(vk, BAR_0, BAR_CARD_ERR_MEM); |
| BCM_VK_EXTRACT_FIELD(ecc_mem_err, reg, |
| BCM_VK_MEM_ERR_FIELD_MASK, |
| BCM_VK_ECC_MEM_ERR_SHIFT); |
| if ((ecc_mem_err != vk->alert_cnts.ecc) && |
| (ecc_mem_err >= BCM_VK_ECC_THRESHOLD)) |
| dev_info(dev, "ALERT! %s.%d ecc RAISED - ErrCnt %d\n", |
| DRV_MODULE_NAME, vk->devid, |
| ecc_mem_err); |
| vk->alert_cnts.ecc = ecc_mem_err; |
| } else if (masked_val != latched_val) { |
| /* print a log as info */ |
| dev_info(dev, "ALERT! %s.%d %s %s\n", |
| DRV_MODULE_NAME, vk->devid, entry->str, |
| masked_val ? "RAISED" : "CLEARED"); |
| } |
| } |
| } |
| |
| static void bcm_vk_dump_peer_log(struct bcm_vk *vk) |
| { |
| struct bcm_vk_peer_log log; |
| struct bcm_vk_peer_log *log_info = &vk->peerlog_info; |
| char loc_buf[BCM_VK_PEER_LOG_LINE_MAX]; |
| int cnt; |
| struct device *dev = &vk->pdev->dev; |
| unsigned int data_offset; |
| |
| memcpy_fromio(&log, vk->bar[BAR_2] + vk->peerlog_off, sizeof(log)); |
| |
| dev_dbg(dev, "Peer PANIC: Size 0x%x(0x%x), [Rd Wr] = [%d %d]\n", |
| log.buf_size, log.mask, log.rd_idx, log.wr_idx); |
| |
| if (!log_info->buf_size) { |
| dev_err(dev, "Peer log dump disabled - skipped!\n"); |
| return; |
| } |
| |
| /* perform range checking for rd/wr idx */ |
| if ((log.rd_idx > log_info->mask) || |
| (log.wr_idx > log_info->mask) || |
| (log.buf_size != log_info->buf_size) || |
| (log.mask != log_info->mask)) { |
| dev_err(dev, |
| "Corrupted Ptrs: Size 0x%x(0x%x) Mask 0x%x(0x%x) [Rd Wr] = [%d %d], skip log dump.\n", |
| log_info->buf_size, log.buf_size, |
| log_info->mask, log.mask, |
| log.rd_idx, log.wr_idx); |
| return; |
| } |
| |
| cnt = 0; |
| data_offset = vk->peerlog_off + sizeof(struct bcm_vk_peer_log); |
| loc_buf[BCM_VK_PEER_LOG_LINE_MAX - 1] = '\0'; |
| while (log.rd_idx != log.wr_idx) { |
| loc_buf[cnt] = vkread8(vk, BAR_2, data_offset + log.rd_idx); |
| |
| if ((loc_buf[cnt] == '\0') || |
| (cnt == (BCM_VK_PEER_LOG_LINE_MAX - 1))) { |
| dev_err(dev, "%s", loc_buf); |
| cnt = 0; |
| } else { |
| cnt++; |
| } |
| log.rd_idx = (log.rd_idx + 1) & log.mask; |
| } |
| /* update rd idx at the end */ |
| vkwrite32(vk, log.rd_idx, BAR_2, |
| vk->peerlog_off + offsetof(struct bcm_vk_peer_log, rd_idx)); |
| } |
| |
| void bcm_vk_handle_notf(struct bcm_vk *vk) |
| { |
| u32 reg; |
| struct bcm_vk_alert alert; |
| bool intf_down; |
| unsigned long flags; |
| |
| /* handle peer alerts and then locally detected ones */ |
| reg = vkread32(vk, BAR_0, BAR_CARD_ERR_LOG); |
| intf_down = BCM_VK_INTF_IS_DOWN(reg); |
| if (!intf_down) { |
| vk->peer_alert.notfs = reg; |
| bcm_vk_log_notf(vk, &vk->peer_alert, bcm_vk_peer_err, |
| ARRAY_SIZE(bcm_vk_peer_err)); |
| vk->peer_alert.flags = vk->peer_alert.notfs; |
| } else { |
| /* turn off access */ |
| bcm_vk_blk_drv_access(vk); |
| } |
| |
| /* check and make copy of alert with lock and then free lock */ |
| spin_lock_irqsave(&vk->host_alert_lock, flags); |
| if (intf_down) |
| vk->host_alert.notfs |= ERR_LOG_HOST_PCIE_DWN; |
| |
| alert = vk->host_alert; |
| vk->host_alert.flags = vk->host_alert.notfs; |
| spin_unlock_irqrestore(&vk->host_alert_lock, flags); |
| |
| /* call display with copy */ |
| bcm_vk_log_notf(vk, &alert, bcm_vk_host_err, |
| ARRAY_SIZE(bcm_vk_host_err)); |
| |
| /* |
| * If it is a sys fault or heartbeat timeout, we would like extract |
| * log msg from the card so that we would know what is the last fault |
| */ |
| if (!intf_down && |
| ((vk->host_alert.flags & ERR_LOG_HOST_HB_FAIL) || |
| (vk->peer_alert.flags & ERR_LOG_SYS_FAULT))) |
| bcm_vk_dump_peer_log(vk); |
| } |
| |
| static inline int bcm_vk_wait(struct bcm_vk *vk, enum pci_barno bar, |
| u64 offset, u32 mask, u32 value, |
| unsigned long timeout_ms) |
| { |
| struct device *dev = &vk->pdev->dev; |
| unsigned long start_time; |
| unsigned long timeout; |
| u32 rd_val, boot_status; |
| |
| start_time = jiffies; |
| timeout = start_time + msecs_to_jiffies(timeout_ms); |
| |
| do { |
| rd_val = vkread32(vk, bar, offset); |
| dev_dbg(dev, "BAR%d Offset=0x%llx: 0x%x\n", |
| bar, offset, rd_val); |
| |
| /* check for any boot err condition */ |
| boot_status = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| if (boot_status & BOOT_ERR_MASK) { |
| dev_err(dev, "Boot Err 0x%x, progress 0x%x after %d ms\n", |
| (boot_status & BOOT_ERR_MASK) >> BOOT_ERR_SHIFT, |
| boot_status & BOOT_PROG_MASK, |
| jiffies_to_msecs(jiffies - start_time)); |
| return -EFAULT; |
| } |
| |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| |
| cpu_relax(); |
| cond_resched(); |
| } while ((rd_val & mask) != value); |
| |
| return 0; |
| } |
| |
| static void bcm_vk_get_card_info(struct bcm_vk *vk) |
| { |
| struct device *dev = &vk->pdev->dev; |
| u32 offset; |
| int i; |
| u8 *dst; |
| struct bcm_vk_card_info *info = &vk->card_info; |
| |
| /* first read the offset from spare register */ |
| offset = vkread32(vk, BAR_0, BAR_CARD_STATIC_INFO); |
| offset &= (pci_resource_len(vk->pdev, BAR_2 * 2) - 1); |
| |
| /* based on the offset, read info to internal card info structure */ |
| dst = (u8 *)info; |
| for (i = 0; i < sizeof(*info); i++) |
| *dst++ = vkread8(vk, BAR_2, offset++); |
| |
| #define CARD_INFO_LOG_FMT "version : %x\n" \ |
| "os_tag : %s\n" \ |
| "cmpt_tag : %s\n" \ |
| "cpu_freq : %d MHz\n" \ |
| "cpu_scale : %d full, %d lowest\n" \ |
| "ddr_freq : %d MHz\n" \ |
| "ddr_size : %d MB\n" \ |
| "video_freq: %d MHz\n" |
| dev_dbg(dev, CARD_INFO_LOG_FMT, info->version, info->os_tag, |
| info->cmpt_tag, info->cpu_freq_mhz, info->cpu_scale[0], |
| info->cpu_scale[MAX_OPP - 1], info->ddr_freq_mhz, |
| info->ddr_size_MB, info->video_core_freq_mhz); |
| |
| /* |
| * get the peer log pointer, only need the offset, and get record |
| * of the log buffer information which would be used for checking |
| * before dump, in case the BAR2 memory has been corrupted. |
| */ |
| vk->peerlog_off = offset; |
| memcpy_fromio(&vk->peerlog_info, vk->bar[BAR_2] + vk->peerlog_off, |
| sizeof(vk->peerlog_info)); |
| |
| /* |
| * Do a range checking and if out of bound, the record will be zeroed |
| * which guarantees that nothing would be dumped. In other words, |
| * peer dump is disabled. |
| */ |
| if ((vk->peerlog_info.buf_size > BCM_VK_PEER_LOG_BUF_MAX) || |
| (vk->peerlog_info.mask != (vk->peerlog_info.buf_size - 1)) || |
| (vk->peerlog_info.rd_idx > vk->peerlog_info.mask) || |
| (vk->peerlog_info.wr_idx > vk->peerlog_info.mask)) { |
| dev_err(dev, "Peer log disabled - range error: Size 0x%x(0x%x), [Rd Wr] = [%d %d]\n", |
| vk->peerlog_info.buf_size, |
| vk->peerlog_info.mask, |
| vk->peerlog_info.rd_idx, |
| vk->peerlog_info.wr_idx); |
| memset(&vk->peerlog_info, 0, sizeof(vk->peerlog_info)); |
| } else { |
| dev_dbg(dev, "Peer log: Size 0x%x(0x%x), [Rd Wr] = [%d %d]\n", |
| vk->peerlog_info.buf_size, |
| vk->peerlog_info.mask, |
| vk->peerlog_info.rd_idx, |
| vk->peerlog_info.wr_idx); |
| } |
| } |
| |
| static void bcm_vk_get_proc_mon_info(struct bcm_vk *vk) |
| { |
| struct device *dev = &vk->pdev->dev; |
| struct bcm_vk_proc_mon_info *mon = &vk->proc_mon_info; |
| u32 num, entry_size, offset, buf_size; |
| u8 *dst; |
| |
| /* calculate offset which is based on peerlog offset */ |
| buf_size = vkread32(vk, BAR_2, |
| vk->peerlog_off |
| + offsetof(struct bcm_vk_peer_log, buf_size)); |
| offset = vk->peerlog_off + sizeof(struct bcm_vk_peer_log) |
| + buf_size; |
| |
| /* first read the num and entry size */ |
| num = vkread32(vk, BAR_2, offset); |
| entry_size = vkread32(vk, BAR_2, offset + sizeof(num)); |
| |
| /* check for max allowed */ |
| if (num > BCM_VK_PROC_MON_MAX) { |
| dev_err(dev, "Processing monitoring entry %d exceeds max %d\n", |
| num, BCM_VK_PROC_MON_MAX); |
| return; |
| } |
| mon->num = num; |
| mon->entry_size = entry_size; |
| |
| vk->proc_mon_off = offset; |
| |
| /* read it once that will capture those static info */ |
| dst = (u8 *)&mon->entries[0]; |
| offset += sizeof(num) + sizeof(entry_size); |
| memcpy_fromio(dst, vk->bar[BAR_2] + offset, num * entry_size); |
| } |
| |
| static int bcm_vk_sync_card_info(struct bcm_vk *vk) |
| { |
| u32 rdy_marker = vkread32(vk, BAR_1, VK_BAR1_MSGQ_DEF_RDY); |
| |
| /* check for marker, but allow diags mode to skip sync */ |
| if (!bcm_vk_msgq_marker_valid(vk)) |
| return (rdy_marker == VK_BAR1_DIAG_RDY_MARKER ? 0 : -EINVAL); |
| |
| /* |
| * Write down scratch addr which is used for DMA. For |
| * signed part, BAR1 is accessible only after boot2 has come |
| * up |
| */ |
| if (vk->tdma_addr) { |
| vkwrite32(vk, (u64)vk->tdma_addr >> 32, BAR_1, |
| VK_BAR1_SCRATCH_OFF_HI); |
| vkwrite32(vk, (u32)vk->tdma_addr, BAR_1, |
| VK_BAR1_SCRATCH_OFF_LO); |
| vkwrite32(vk, nr_scratch_pages * PAGE_SIZE, BAR_1, |
| VK_BAR1_SCRATCH_SZ_ADDR); |
| } |
| |
| /* get static card info, only need to read once */ |
| bcm_vk_get_card_info(vk); |
| |
| /* get the proc mon info once */ |
| bcm_vk_get_proc_mon_info(vk); |
| |
| return 0; |
| } |
| |
| void bcm_vk_blk_drv_access(struct bcm_vk *vk) |
| { |
| int i; |
| |
| /* |
| * kill all the apps except for the process that is resetting. |
| * If not called during reset, reset_pid will be 0, and all will be |
| * killed. |
| */ |
| spin_lock(&vk->ctx_lock); |
| |
| /* set msgq_inited to 0 so that all rd/wr will be blocked */ |
| atomic_set(&vk->msgq_inited, 0); |
| |
| for (i = 0; i < VK_PID_HT_SZ; i++) { |
| struct bcm_vk_ctx *ctx; |
| |
| list_for_each_entry(ctx, &vk->pid_ht[i].head, node) { |
| if (ctx->pid != vk->reset_pid) { |
| dev_dbg(&vk->pdev->dev, |
| "Send kill signal to pid %d\n", |
| ctx->pid); |
| kill_pid(find_vpid(ctx->pid), SIGKILL, 1); |
| } |
| } |
| } |
| bcm_vk_tty_terminate_tty_user(vk); |
| spin_unlock(&vk->ctx_lock); |
| } |
| |
| static void bcm_vk_buf_notify(struct bcm_vk *vk, void *bufp, |
| dma_addr_t host_buf_addr, u32 buf_size) |
| { |
| /* update the dma address to the card */ |
| vkwrite32(vk, (u64)host_buf_addr >> 32, BAR_1, |
| VK_BAR1_DMA_BUF_OFF_HI); |
| vkwrite32(vk, (u32)host_buf_addr, BAR_1, |
| VK_BAR1_DMA_BUF_OFF_LO); |
| vkwrite32(vk, buf_size, BAR_1, VK_BAR1_DMA_BUF_SZ); |
| } |
| |
| static int bcm_vk_load_image_by_type(struct bcm_vk *vk, u32 load_type, |
| const char *filename) |
| { |
| struct device *dev = &vk->pdev->dev; |
| const struct firmware *fw = NULL; |
| void *bufp = NULL; |
| size_t max_buf, offset; |
| int ret; |
| u64 offset_codepush; |
| u32 codepush; |
| u32 value; |
| dma_addr_t boot_dma_addr; |
| bool is_stdalone; |
| |
| if (load_type == VK_IMAGE_TYPE_BOOT1) { |
| /* |
| * After POR, enable VK soft BOOTSRC so bootrom do not clear |
| * the pushed image (the TCM memories). |
| */ |
| value = vkread32(vk, BAR_0, BAR_BOOTSRC_SELECT); |
| value |= BOOTSRC_SOFT_ENABLE; |
| vkwrite32(vk, value, BAR_0, BAR_BOOTSRC_SELECT); |
| |
| codepush = CODEPUSH_BOOTSTART + CODEPUSH_BOOT1_ENTRY; |
| offset_codepush = BAR_CODEPUSH_SBL; |
| |
| /* Write a 1 to request SRAM open bit */ |
| vkwrite32(vk, CODEPUSH_BOOTSTART, BAR_0, offset_codepush); |
| |
| /* Wait for VK to respond */ |
| ret = bcm_vk_wait(vk, BAR_0, BAR_BOOT_STATUS, SRAM_OPEN, |
| SRAM_OPEN, LOAD_IMAGE_TIMEOUT_MS); |
| if (ret < 0) { |
| dev_err(dev, "boot1 wait SRAM err - ret(%d)\n", ret); |
| goto err_buf_out; |
| } |
| |
| max_buf = SZ_256K; |
| bufp = dma_alloc_coherent(dev, |
| max_buf, |
| &boot_dma_addr, GFP_KERNEL); |
| if (!bufp) { |
| dev_err(dev, "Error allocating 0x%zx\n", max_buf); |
| ret = -ENOMEM; |
| goto err_buf_out; |
| } |
| } else if (load_type == VK_IMAGE_TYPE_BOOT2) { |
| codepush = CODEPUSH_BOOT2_ENTRY; |
| offset_codepush = BAR_CODEPUSH_SBI; |
| |
| /* Wait for VK to respond */ |
| ret = bcm_vk_wait(vk, BAR_0, BAR_BOOT_STATUS, DDR_OPEN, |
| DDR_OPEN, LOAD_IMAGE_TIMEOUT_MS); |
| if (ret < 0) { |
| dev_err(dev, "boot2 wait DDR open error - ret(%d)\n", |
| ret); |
| goto err_buf_out; |
| } |
| |
| max_buf = SZ_4M; |
| bufp = dma_alloc_coherent(dev, |
| max_buf, |
| &boot_dma_addr, GFP_KERNEL); |
| if (!bufp) { |
| dev_err(dev, "Error allocating 0x%zx\n", max_buf); |
| ret = -ENOMEM; |
| goto err_buf_out; |
| } |
| |
| bcm_vk_buf_notify(vk, bufp, boot_dma_addr, max_buf); |
| } else { |
| dev_err(dev, "Error invalid image type 0x%x\n", load_type); |
| ret = -EINVAL; |
| goto err_buf_out; |
| } |
| |
| offset = 0; |
| ret = request_partial_firmware_into_buf(&fw, filename, dev, |
| bufp, max_buf, offset); |
| if (ret) { |
| dev_err(dev, "Error %d requesting firmware file: %s\n", |
| ret, filename); |
| goto err_firmware_out; |
| } |
| dev_dbg(dev, "size=0x%zx\n", fw->size); |
| if (load_type == VK_IMAGE_TYPE_BOOT1) |
| memcpy_toio(vk->bar[BAR_1] + BAR1_CODEPUSH_BASE_BOOT1, |
| bufp, |
| fw->size); |
| |
| dev_dbg(dev, "Signaling 0x%x to 0x%llx\n", codepush, offset_codepush); |
| vkwrite32(vk, codepush, BAR_0, offset_codepush); |
| |
| if (load_type == VK_IMAGE_TYPE_BOOT1) { |
| u32 boot_status; |
| |
| /* wait until done */ |
| ret = bcm_vk_wait(vk, BAR_0, BAR_BOOT_STATUS, |
| BOOT1_RUNNING, |
| BOOT1_RUNNING, |
| BOOT1_STARTUP_TIMEOUT_MS); |
| |
| boot_status = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| is_stdalone = !BCM_VK_INTF_IS_DOWN(boot_status) && |
| (boot_status & BOOT_STDALONE_RUNNING); |
| if (ret && !is_stdalone) { |
| dev_err(dev, |
| "Timeout %ld ms waiting for boot1 to come up - ret(%d)\n", |
| BOOT1_STARTUP_TIMEOUT_MS, ret); |
| goto err_firmware_out; |
| } else if (is_stdalone) { |
| u32 reg; |
| |
| reg = vkread32(vk, BAR_0, BAR_BOOT1_STDALONE_PROGRESS); |
| if ((reg & BOOT1_STDALONE_PROGRESS_MASK) == |
| BOOT1_STDALONE_SUCCESS) { |
| dev_info(dev, "Boot1 standalone success\n"); |
| ret = 0; |
| } else { |
| dev_err(dev, "Timeout %ld ms - Boot1 standalone failure\n", |
| BOOT1_STARTUP_TIMEOUT_MS); |
| ret = -EINVAL; |
| goto err_firmware_out; |
| } |
| } |
| } else if (load_type == VK_IMAGE_TYPE_BOOT2) { |
| unsigned long timeout; |
| |
| timeout = jiffies + msecs_to_jiffies(LOAD_IMAGE_TIMEOUT_MS); |
| |
| /* To send more data to VK than max_buf allowed at a time */ |
| do { |
| /* |
| * Check for ack from card. when Ack is received, |
| * it means all the data is received by card. |
| * Exit the loop after ack is received. |
| */ |
| ret = bcm_vk_wait(vk, BAR_0, BAR_BOOT_STATUS, |
| FW_LOADER_ACK_RCVD_ALL_DATA, |
| FW_LOADER_ACK_RCVD_ALL_DATA, |
| TXFR_COMPLETE_TIMEOUT_MS); |
| if (ret == 0) { |
| dev_dbg(dev, "Exit boot2 download\n"); |
| break; |
| } else if (ret == -EFAULT) { |
| dev_err(dev, "Error detected during ACK waiting"); |
| goto err_firmware_out; |
| } |
| |
| /* exit the loop, if there is no response from card */ |
| if (time_after(jiffies, timeout)) { |
| dev_err(dev, "Error. No reply from card\n"); |
| ret = -ETIMEDOUT; |
| goto err_firmware_out; |
| } |
| |
| /* Wait for VK to open BAR space to copy new data */ |
| ret = bcm_vk_wait(vk, BAR_0, offset_codepush, |
| codepush, 0, |
| TXFR_COMPLETE_TIMEOUT_MS); |
| if (ret == 0) { |
| offset += max_buf; |
| ret = request_partial_firmware_into_buf |
| (&fw, |
| filename, |
| dev, bufp, |
| max_buf, |
| offset); |
| if (ret) { |
| dev_err(dev, |
| "Error %d requesting firmware file: %s offset: 0x%zx\n", |
| ret, filename, offset); |
| goto err_firmware_out; |
| } |
| dev_dbg(dev, "size=0x%zx\n", fw->size); |
| dev_dbg(dev, "Signaling 0x%x to 0x%llx\n", |
| codepush, offset_codepush); |
| vkwrite32(vk, codepush, BAR_0, offset_codepush); |
| /* reload timeout after every codepush */ |
| timeout = jiffies + |
| msecs_to_jiffies(LOAD_IMAGE_TIMEOUT_MS); |
| } else if (ret == -EFAULT) { |
| dev_err(dev, "Error detected waiting for transfer\n"); |
| goto err_firmware_out; |
| } |
| } while (1); |
| |
| /* wait for fw status bits to indicate app ready */ |
| ret = bcm_vk_wait(vk, BAR_0, VK_BAR_FWSTS, |
| VK_FWSTS_READY, |
| VK_FWSTS_READY, |
| BOOT2_STARTUP_TIMEOUT_MS); |
| if (ret < 0) { |
| dev_err(dev, "Boot2 not ready - ret(%d)\n", ret); |
| goto err_firmware_out; |
| } |
| |
| is_stdalone = vkread32(vk, BAR_0, BAR_BOOT_STATUS) & |
| BOOT_STDALONE_RUNNING; |
| if (!is_stdalone) { |
| ret = bcm_vk_intf_ver_chk(vk); |
| if (ret) { |
| dev_err(dev, "failure in intf version check\n"); |
| goto err_firmware_out; |
| } |
| |
| /* |
| * Next, initialize Message Q if we are loading boot2. |
| * Do a force sync |
| */ |
| ret = bcm_vk_sync_msgq(vk, true); |
| if (ret) { |
| dev_err(dev, "Boot2 Error reading comm msg Q info\n"); |
| ret = -EIO; |
| goto err_firmware_out; |
| } |
| |
| /* sync & channel other info */ |
| ret = bcm_vk_sync_card_info(vk); |
| if (ret) { |
| dev_err(dev, "Syncing Card Info failure\n"); |
| goto err_firmware_out; |
| } |
| } |
| } |
| |
| err_firmware_out: |
| release_firmware(fw); |
| |
| err_buf_out: |
| if (bufp) |
| dma_free_coherent(dev, max_buf, bufp, boot_dma_addr); |
| |
| return ret; |
| } |
| |
| static u32 bcm_vk_next_boot_image(struct bcm_vk *vk) |
| { |
| u32 boot_status; |
| u32 fw_status; |
| u32 load_type = 0; /* default for unknown */ |
| |
| boot_status = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| fw_status = vkread32(vk, BAR_0, VK_BAR_FWSTS); |
| |
| if (!BCM_VK_INTF_IS_DOWN(boot_status) && (boot_status & SRAM_OPEN)) |
| load_type = VK_IMAGE_TYPE_BOOT1; |
| else if (boot_status == BOOT1_RUNNING) |
| load_type = VK_IMAGE_TYPE_BOOT2; |
| |
| /* Log status so that we know different stages */ |
| dev_info(&vk->pdev->dev, |
| "boot-status value for next image: 0x%x : fw-status 0x%x\n", |
| boot_status, fw_status); |
| |
| return load_type; |
| } |
| |
| static enum soc_idx get_soc_idx(struct bcm_vk *vk) |
| { |
| struct pci_dev *pdev = vk->pdev; |
| enum soc_idx idx = VK_IDX_INVALID; |
| u32 rev; |
| static enum soc_idx const vk_soc_tab[] = { VALKYRIE_A0, VALKYRIE_B0 }; |
| |
| switch (pdev->device) { |
| case PCI_DEVICE_ID_VALKYRIE: |
| /* get the chip id to decide sub-class */ |
| rev = MAJOR_SOC_REV(vkread32(vk, BAR_0, BAR_CHIP_ID)); |
| if (rev < ARRAY_SIZE(vk_soc_tab)) { |
| idx = vk_soc_tab[rev]; |
| } else { |
| /* Default to A0 firmware for all other chip revs */ |
| idx = VALKYRIE_A0; |
| dev_warn(&pdev->dev, |
| "Rev %d not in image lookup table, default to idx=%d\n", |
| rev, idx); |
| } |
| break; |
| |
| case PCI_DEVICE_ID_VIPER: |
| idx = VIPER; |
| break; |
| |
| default: |
| dev_err(&pdev->dev, "no images for 0x%x\n", pdev->device); |
| } |
| return idx; |
| } |
| |
| static const char *get_load_fw_name(struct bcm_vk *vk, |
| const struct load_image_entry *entry) |
| { |
| const struct firmware *fw; |
| struct device *dev = &vk->pdev->dev; |
| int ret; |
| unsigned long dummy; |
| int i; |
| |
| for (i = 0; i < IMG_PER_TYPE_MAX; i++) { |
| fw = NULL; |
| ret = request_partial_firmware_into_buf(&fw, |
| entry->image_name[i], |
| dev, &dummy, |
| sizeof(dummy), |
| 0); |
| release_firmware(fw); |
| if (!ret) |
| return entry->image_name[i]; |
| } |
| return NULL; |
| } |
| |
| int bcm_vk_auto_load_all_images(struct bcm_vk *vk) |
| { |
| int i, ret = -1; |
| enum soc_idx idx; |
| struct device *dev = &vk->pdev->dev; |
| u32 curr_type; |
| const char *curr_name; |
| |
| idx = get_soc_idx(vk); |
| if (idx == VK_IDX_INVALID) |
| goto auto_load_all_exit; |
| |
| /* log a message to know the relative loading order */ |
| dev_dbg(dev, "Load All for device %d\n", vk->devid); |
| |
| for (i = 0; i < NUM_BOOT_STAGES; i++) { |
| curr_type = image_tab[idx][i].image_type; |
| if (bcm_vk_next_boot_image(vk) == curr_type) { |
| curr_name = get_load_fw_name(vk, &image_tab[idx][i]); |
| if (!curr_name) { |
| dev_err(dev, "No suitable firmware exists for type %d", |
| curr_type); |
| ret = -ENOENT; |
| goto auto_load_all_exit; |
| } |
| ret = bcm_vk_load_image_by_type(vk, curr_type, |
| curr_name); |
| dev_info(dev, "Auto load %s, ret %d\n", |
| curr_name, ret); |
| |
| if (ret) { |
| dev_err(dev, "Error loading default %s\n", |
| curr_name); |
| goto auto_load_all_exit; |
| } |
| } |
| } |
| |
| auto_load_all_exit: |
| return ret; |
| } |
| |
| static int bcm_vk_trigger_autoload(struct bcm_vk *vk) |
| { |
| if (test_and_set_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload) != 0) |
| return -EPERM; |
| |
| set_bit(BCM_VK_WQ_DWNLD_AUTO, vk->wq_offload); |
| queue_work(vk->wq_thread, &vk->wq_work); |
| |
| return 0; |
| } |
| |
| /* |
| * deferred work queue for draining and auto download. |
| */ |
| static void bcm_vk_wq_handler(struct work_struct *work) |
| { |
| struct bcm_vk *vk = container_of(work, struct bcm_vk, wq_work); |
| struct device *dev = &vk->pdev->dev; |
| s32 ret; |
| |
| /* check wq offload bit map to perform various operations */ |
| if (test_bit(BCM_VK_WQ_NOTF_PEND, vk->wq_offload)) { |
| /* clear bit right the way for notification */ |
| clear_bit(BCM_VK_WQ_NOTF_PEND, vk->wq_offload); |
| bcm_vk_handle_notf(vk); |
| } |
| if (test_bit(BCM_VK_WQ_DWNLD_AUTO, vk->wq_offload)) { |
| bcm_vk_auto_load_all_images(vk); |
| |
| /* |
| * at the end of operation, clear AUTO bit and pending |
| * bit |
| */ |
| clear_bit(BCM_VK_WQ_DWNLD_AUTO, vk->wq_offload); |
| clear_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload); |
| } |
| |
| /* next, try to drain */ |
| ret = bcm_to_h_msg_dequeue(vk); |
| |
| if (ret == 0) |
| dev_dbg(dev, "Spurious trigger for workqueue\n"); |
| else if (ret < 0) |
| bcm_vk_blk_drv_access(vk); |
| } |
| |
| static long bcm_vk_load_image(struct bcm_vk *vk, |
| const struct vk_image __user *arg) |
| { |
| struct device *dev = &vk->pdev->dev; |
| const char *image_name; |
| struct vk_image image; |
| u32 next_loadable; |
| enum soc_idx idx; |
| int image_idx; |
| int ret = -EPERM; |
| |
| if (copy_from_user(&image, arg, sizeof(image))) |
| return -EACCES; |
| |
| if ((image.type != VK_IMAGE_TYPE_BOOT1) && |
| (image.type != VK_IMAGE_TYPE_BOOT2)) { |
| dev_err(dev, "invalid image.type %u\n", image.type); |
| return ret; |
| } |
| |
| next_loadable = bcm_vk_next_boot_image(vk); |
| if (next_loadable != image.type) { |
| dev_err(dev, "Next expected image %u, Loading %u\n", |
| next_loadable, image.type); |
| return ret; |
| } |
| |
| /* |
| * if something is pending download already. This could only happen |
| * for now when the driver is being loaded, or if someone has issued |
| * another download command in another shell. |
| */ |
| if (test_and_set_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload) != 0) { |
| dev_err(dev, "Download operation already pending.\n"); |
| return ret; |
| } |
| |
| image_name = image.filename; |
| if (image_name[0] == '\0') { |
| /* Use default image name if NULL */ |
| idx = get_soc_idx(vk); |
| if (idx == VK_IDX_INVALID) |
| goto err_idx; |
| |
| /* Image idx starts with boot1 */ |
| image_idx = image.type - VK_IMAGE_TYPE_BOOT1; |
| image_name = get_load_fw_name(vk, &image_tab[idx][image_idx]); |
| if (!image_name) { |
| dev_err(dev, "No suitable image found for type %d", |
| image.type); |
| ret = -ENOENT; |
| goto err_idx; |
| } |
| } else { |
| /* Ensure filename is NULL terminated */ |
| image.filename[sizeof(image.filename) - 1] = '\0'; |
| } |
| ret = bcm_vk_load_image_by_type(vk, image.type, image_name); |
| dev_info(dev, "Load %s, ret %d\n", image_name, ret); |
| err_idx: |
| clear_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload); |
| |
| return ret; |
| } |
| |
| static int bcm_vk_reset_successful(struct bcm_vk *vk) |
| { |
| struct device *dev = &vk->pdev->dev; |
| u32 fw_status, reset_reason; |
| int ret = -EAGAIN; |
| |
| /* |
| * Reset could be triggered when the card in several state: |
| * i) in bootROM |
| * ii) after boot1 |
| * iii) boot2 running |
| * |
| * i) & ii) - no status bits will be updated. If vkboot1 |
| * runs automatically after reset, it will update the reason |
| * to be unknown reason |
| * iii) - reboot reason match + deinit done. |
| */ |
| fw_status = vkread32(vk, BAR_0, VK_BAR_FWSTS); |
| /* immediate exit if interface goes down */ |
| if (BCM_VK_INTF_IS_DOWN(fw_status)) { |
| dev_err(dev, "PCIe Intf Down!\n"); |
| goto reset_exit; |
| } |
| |
| reset_reason = (fw_status & VK_FWSTS_RESET_REASON_MASK); |
| if ((reset_reason == VK_FWSTS_RESET_MBOX_DB) || |
| (reset_reason == VK_FWSTS_RESET_UNKNOWN)) |
| ret = 0; |
| |
| /* |
| * if some of the deinit bits are set, but done |
| * bit is not, this is a failure if triggered while boot2 is running |
| */ |
| if ((fw_status & VK_FWSTS_DEINIT_TRIGGERED) && |
| !(fw_status & VK_FWSTS_RESET_DONE)) |
| ret = -EAGAIN; |
| |
| reset_exit: |
| dev_dbg(dev, "FW status = 0x%x ret %d\n", fw_status, ret); |
| |
| return ret; |
| } |
| |
| static void bcm_to_v_reset_doorbell(struct bcm_vk *vk, u32 db_val) |
| { |
| vkwrite32(vk, db_val, BAR_0, VK_BAR0_RESET_DB_BASE); |
| } |
| |
| static int bcm_vk_trigger_reset(struct bcm_vk *vk) |
| { |
| u32 i; |
| u32 value, boot_status; |
| bool is_stdalone, is_boot2; |
| static const u32 bar0_reg_clr_list[] = { BAR_OS_UPTIME, |
| BAR_INTF_VER, |
| BAR_CARD_VOLTAGE, |
| BAR_CARD_TEMPERATURE, |
| BAR_CARD_PWR_AND_THRE }; |
| |
| /* clean up before pressing the door bell */ |
| bcm_vk_drain_msg_on_reset(vk); |
| vkwrite32(vk, 0, BAR_1, VK_BAR1_MSGQ_DEF_RDY); |
| /* make tag '\0' terminated */ |
| vkwrite32(vk, 0, BAR_1, VK_BAR1_BOOT1_VER_TAG); |
| |
| for (i = 0; i < VK_BAR1_DAUTH_MAX; i++) { |
| vkwrite32(vk, 0, BAR_1, VK_BAR1_DAUTH_STORE_ADDR(i)); |
| vkwrite32(vk, 0, BAR_1, VK_BAR1_DAUTH_VALID_ADDR(i)); |
| } |
| for (i = 0; i < VK_BAR1_SOTP_REVID_MAX; i++) |
| vkwrite32(vk, 0, BAR_1, VK_BAR1_SOTP_REVID_ADDR(i)); |
| |
| memset(&vk->card_info, 0, sizeof(vk->card_info)); |
| memset(&vk->peerlog_info, 0, sizeof(vk->peerlog_info)); |
| memset(&vk->proc_mon_info, 0, sizeof(vk->proc_mon_info)); |
| memset(&vk->alert_cnts, 0, sizeof(vk->alert_cnts)); |
| |
| /* |
| * When boot request fails, the CODE_PUSH_OFFSET stays persistent. |
| * Allowing us to debug the failure. When we call reset, |
| * we should clear CODE_PUSH_OFFSET so ROM does not execute |
| * boot again (and fails again) and instead waits for a new |
| * codepush. And, if previous boot has encountered error, need |
| * to clear the entry values |
| */ |
| boot_status = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| if (boot_status & BOOT_ERR_MASK) { |
| dev_info(&vk->pdev->dev, |
| "Card in boot error 0x%x, clear CODEPUSH val\n", |
| boot_status); |
| value = 0; |
| } else { |
| value = vkread32(vk, BAR_0, BAR_CODEPUSH_SBL); |
| value &= CODEPUSH_MASK; |
| } |
| vkwrite32(vk, value, BAR_0, BAR_CODEPUSH_SBL); |
| |
| /* special reset handling */ |
| is_stdalone = boot_status & BOOT_STDALONE_RUNNING; |
| is_boot2 = (boot_status & BOOT_STATE_MASK) == BOOT2_RUNNING; |
| if (vk->peer_alert.flags & ERR_LOG_RAMDUMP) { |
| /* |
| * if card is in ramdump mode, it is hitting an error. Don't |
| * reset the reboot reason as it will contain valid info that |
| * is important - simply use special reset |
| */ |
| vkwrite32(vk, VK_BAR0_RESET_RAMPDUMP, BAR_0, VK_BAR_FWSTS); |
| return VK_BAR0_RESET_RAMPDUMP; |
| } else if (is_stdalone && !is_boot2) { |
| dev_info(&vk->pdev->dev, "Hard reset on Standalone mode"); |
| bcm_to_v_reset_doorbell(vk, VK_BAR0_RESET_DB_HARD); |
| return VK_BAR0_RESET_DB_HARD; |
| } |
| |
| /* reset fw_status with proper reason, and press db */ |
| vkwrite32(vk, VK_FWSTS_RESET_MBOX_DB, BAR_0, VK_BAR_FWSTS); |
| bcm_to_v_reset_doorbell(vk, VK_BAR0_RESET_DB_SOFT); |
| |
| /* clear other necessary registers and alert records */ |
| for (i = 0; i < ARRAY_SIZE(bar0_reg_clr_list); i++) |
| vkwrite32(vk, 0, BAR_0, bar0_reg_clr_list[i]); |
| memset(&vk->host_alert, 0, sizeof(vk->host_alert)); |
| memset(&vk->peer_alert, 0, sizeof(vk->peer_alert)); |
| /* clear 4096 bits of bitmap */ |
| bitmap_clear(vk->bmap, 0, VK_MSG_ID_BITMAP_SIZE); |
| |
| return 0; |
| } |
| |
| static long bcm_vk_reset(struct bcm_vk *vk, struct vk_reset __user *arg) |
| { |
| struct device *dev = &vk->pdev->dev; |
| struct vk_reset reset; |
| int ret = 0; |
| u32 ramdump_reset; |
| int special_reset; |
| |
| if (copy_from_user(&reset, arg, sizeof(struct vk_reset))) |
| return -EFAULT; |
| |
| /* check if any download is in-progress, if so return error */ |
| if (test_and_set_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload) != 0) { |
| dev_err(dev, "Download operation pending - skip reset.\n"); |
| return -EPERM; |
| } |
| |
| ramdump_reset = vk->peer_alert.flags & ERR_LOG_RAMDUMP; |
| dev_info(dev, "Issue Reset %s\n", |
| ramdump_reset ? "in ramdump mode" : ""); |
| |
| /* |
| * The following is the sequence of reset: |
| * - send card level graceful shut down |
| * - wait enough time for VK to handle its business, stopping DMA etc |
| * - kill host apps |
| * - Trigger interrupt with DB |
| */ |
| bcm_vk_send_shutdown_msg(vk, VK_SHUTDOWN_GRACEFUL, 0, 0); |
| |
| spin_lock(&vk->ctx_lock); |
| if (!vk->reset_pid) { |
| vk->reset_pid = task_pid_nr(current); |
| } else { |
| dev_err(dev, "Reset already launched by process pid %d\n", |
| vk->reset_pid); |
| ret = -EACCES; |
| } |
| spin_unlock(&vk->ctx_lock); |
| if (ret) |
| goto err_exit; |
| |
| bcm_vk_blk_drv_access(vk); |
| special_reset = bcm_vk_trigger_reset(vk); |
| |
| /* |
| * Wait enough time for card os to deinit |
| * and populate the reset reason. |
| */ |
| msleep(BCM_VK_DEINIT_TIME_MS); |
| |
| if (special_reset) { |
| /* if it is special ramdump reset, return the type to user */ |
| reset.arg2 = special_reset; |
| if (copy_to_user(arg, &reset, sizeof(reset))) |
| ret = -EFAULT; |
| } else { |
| ret = bcm_vk_reset_successful(vk); |
| } |
| |
| err_exit: |
| clear_bit(BCM_VK_WQ_DWNLD_PEND, vk->wq_offload); |
| return ret; |
| } |
| |
| static int bcm_vk_mmap(struct file *file, struct vm_area_struct *vma) |
| { |
| struct bcm_vk_ctx *ctx = file->private_data; |
| struct bcm_vk *vk = container_of(ctx->miscdev, struct bcm_vk, miscdev); |
| unsigned long pg_size; |
| |
| /* only BAR2 is mmap possible, which is bar num 4 due to 64bit */ |
| #define VK_MMAPABLE_BAR 4 |
| |
| pg_size = ((pci_resource_len(vk->pdev, VK_MMAPABLE_BAR) - 1) |
| >> PAGE_SHIFT) + 1; |
| if (vma->vm_pgoff + vma_pages(vma) > pg_size) |
| return -EINVAL; |
| |
| vma->vm_pgoff += (pci_resource_start(vk->pdev, VK_MMAPABLE_BAR) |
| >> PAGE_SHIFT); |
| vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); |
| |
| return io_remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff, |
| vma->vm_end - vma->vm_start, |
| vma->vm_page_prot); |
| } |
| |
| static long bcm_vk_ioctl(struct file *file, unsigned int cmd, unsigned long arg) |
| { |
| long ret = -EINVAL; |
| struct bcm_vk_ctx *ctx = file->private_data; |
| struct bcm_vk *vk = container_of(ctx->miscdev, struct bcm_vk, miscdev); |
| void __user *argp = (void __user *)arg; |
| |
| dev_dbg(&vk->pdev->dev, |
| "ioctl, cmd=0x%02x, arg=0x%02lx\n", |
| cmd, arg); |
| |
| mutex_lock(&vk->mutex); |
| |
| switch (cmd) { |
| case VK_IOCTL_LOAD_IMAGE: |
| ret = bcm_vk_load_image(vk, argp); |
| break; |
| |
| case VK_IOCTL_RESET: |
| ret = bcm_vk_reset(vk, argp); |
| break; |
| |
| default: |
| break; |
| } |
| |
| mutex_unlock(&vk->mutex); |
| |
| return ret; |
| } |
| |
| static const struct file_operations bcm_vk_fops = { |
| .owner = THIS_MODULE, |
| .open = bcm_vk_open, |
| .read = bcm_vk_read, |
| .write = bcm_vk_write, |
| .poll = bcm_vk_poll, |
| .release = bcm_vk_release, |
| .mmap = bcm_vk_mmap, |
| .unlocked_ioctl = bcm_vk_ioctl, |
| }; |
| |
| static int bcm_vk_on_panic(struct notifier_block *nb, |
| unsigned long e, void *p) |
| { |
| struct bcm_vk *vk = container_of(nb, struct bcm_vk, panic_nb); |
| |
| bcm_to_v_reset_doorbell(vk, VK_BAR0_RESET_DB_HARD); |
| |
| return 0; |
| } |
| |
| static int bcm_vk_probe(struct pci_dev *pdev, const struct pci_device_id *ent) |
| { |
| int err; |
| int i; |
| int id; |
| int irq; |
| char name[20]; |
| struct bcm_vk *vk; |
| struct device *dev = &pdev->dev; |
| struct miscdevice *misc_device; |
| u32 boot_status; |
| |
| /* allocate vk structure which is tied to kref for freeing */ |
| vk = kzalloc(sizeof(*vk), GFP_KERNEL); |
| if (!vk) |
| return -ENOMEM; |
| |
| kref_init(&vk->kref); |
| if (nr_ib_sgl_blk > BCM_VK_IB_SGL_BLK_MAX) { |
| dev_warn(dev, "Inband SGL blk %d limited to max %d\n", |
| nr_ib_sgl_blk, BCM_VK_IB_SGL_BLK_MAX); |
| nr_ib_sgl_blk = BCM_VK_IB_SGL_BLK_MAX; |
| } |
| vk->ib_sgl_size = nr_ib_sgl_blk * VK_MSGQ_BLK_SIZE; |
| mutex_init(&vk->mutex); |
| |
| err = pci_enable_device(pdev); |
| if (err) { |
| dev_err(dev, "Cannot enable PCI device\n"); |
| goto err_free_exit; |
| } |
| vk->pdev = pci_dev_get(pdev); |
| |
| err = pci_request_regions(pdev, DRV_MODULE_NAME); |
| if (err) { |
| dev_err(dev, "Cannot obtain PCI resources\n"); |
| goto err_disable_pdev; |
| } |
| |
| /* make sure DMA is good */ |
| err = dma_set_mask_and_coherent(&pdev->dev, |
| DMA_BIT_MASK(BCM_VK_DMA_BITS)); |
| if (err) { |
| dev_err(dev, "failed to set DMA mask\n"); |
| goto err_disable_pdev; |
| } |
| |
| /* The tdma is a scratch area for some DMA testings. */ |
| if (nr_scratch_pages) { |
| vk->tdma_vaddr = dma_alloc_coherent |
| (dev, |
| nr_scratch_pages * PAGE_SIZE, |
| &vk->tdma_addr, GFP_KERNEL); |
| if (!vk->tdma_vaddr) { |
| err = -ENOMEM; |
| goto err_disable_pdev; |
| } |
| } |
| |
| pci_set_master(pdev); |
| pci_set_drvdata(pdev, vk); |
| |
| irq = pci_alloc_irq_vectors(pdev, |
| 1, |
| VK_MSIX_IRQ_MAX, |
| PCI_IRQ_MSI | PCI_IRQ_MSIX); |
| |
| if (irq < VK_MSIX_IRQ_MIN_REQ) { |
| dev_err(dev, "failed to get min %d MSIX interrupts, irq(%d)\n", |
| VK_MSIX_IRQ_MIN_REQ, irq); |
| err = (irq >= 0) ? -EINVAL : irq; |
| goto err_disable_pdev; |
| } |
| |
| if (irq != VK_MSIX_IRQ_MAX) |
| dev_warn(dev, "Number of IRQs %d allocated - requested(%d).\n", |
| irq, VK_MSIX_IRQ_MAX); |
| |
| for (i = 0; i < MAX_BAR; i++) { |
| /* multiple by 2 for 64 bit BAR mapping */ |
| vk->bar[i] = pci_ioremap_bar(pdev, i * 2); |
| if (!vk->bar[i]) { |
| dev_err(dev, "failed to remap BAR%d\n", i); |
| err = -ENOMEM; |
| goto err_iounmap; |
| } |
| } |
| |
| for (vk->num_irqs = 0; |
| vk->num_irqs < VK_MSIX_MSGQ_MAX; |
| vk->num_irqs++) { |
| err = devm_request_irq(dev, pci_irq_vector(pdev, vk->num_irqs), |
| bcm_vk_msgq_irqhandler, |
| IRQF_SHARED, DRV_MODULE_NAME, vk); |
| if (err) { |
| dev_err(dev, "failed to request msgq IRQ %d for MSIX %d\n", |
| pdev->irq + vk->num_irqs, vk->num_irqs + 1); |
| goto err_irq; |
| } |
| } |
| /* one irq for notification from VK */ |
| err = devm_request_irq(dev, pci_irq_vector(pdev, vk->num_irqs), |
| bcm_vk_notf_irqhandler, |
| IRQF_SHARED, DRV_MODULE_NAME, vk); |
| if (err) { |
| dev_err(dev, "failed to request notf IRQ %d for MSIX %d\n", |
| pdev->irq + vk->num_irqs, vk->num_irqs + 1); |
| goto err_irq; |
| } |
| vk->num_irqs++; |
| |
| for (i = 0; |
| (i < VK_MSIX_TTY_MAX) && (vk->num_irqs < irq); |
| i++, vk->num_irqs++) { |
| err = devm_request_irq(dev, pci_irq_vector(pdev, vk->num_irqs), |
| bcm_vk_tty_irqhandler, |
| IRQF_SHARED, DRV_MODULE_NAME, vk); |
| if (err) { |
| dev_err(dev, "failed request tty IRQ %d for MSIX %d\n", |
| pdev->irq + vk->num_irqs, vk->num_irqs + 1); |
| goto err_irq; |
| } |
| bcm_vk_tty_set_irq_enabled(vk, i); |
| } |
| |
| id = ida_simple_get(&bcm_vk_ida, 0, 0, GFP_KERNEL); |
| if (id < 0) { |
| err = id; |
| dev_err(dev, "unable to get id\n"); |
| goto err_irq; |
| } |
| |
| vk->devid = id; |
| snprintf(name, sizeof(name), DRV_MODULE_NAME ".%d", id); |
| misc_device = &vk->miscdev; |
| misc_device->minor = MISC_DYNAMIC_MINOR; |
| misc_device->name = kstrdup(name, GFP_KERNEL); |
| if (!misc_device->name) { |
| err = -ENOMEM; |
| goto err_ida_remove; |
| } |
| misc_device->fops = &bcm_vk_fops, |
| |
| err = misc_register(misc_device); |
| if (err) { |
| dev_err(dev, "failed to register device\n"); |
| goto err_kfree_name; |
| } |
| |
| INIT_WORK(&vk->wq_work, bcm_vk_wq_handler); |
| |
| /* create dedicated workqueue */ |
| vk->wq_thread = create_singlethread_workqueue(name); |
| if (!vk->wq_thread) { |
| dev_err(dev, "Fail to create workqueue thread\n"); |
| err = -ENOMEM; |
| goto err_misc_deregister; |
| } |
| |
| err = bcm_vk_msg_init(vk); |
| if (err) { |
| dev_err(dev, "failed to init msg queue info\n"); |
| goto err_destroy_workqueue; |
| } |
| |
| /* sync other info */ |
| bcm_vk_sync_card_info(vk); |
| |
| /* register for panic notifier */ |
| vk->panic_nb.notifier_call = bcm_vk_on_panic; |
| err = atomic_notifier_chain_register(&panic_notifier_list, |
| &vk->panic_nb); |
| if (err) { |
| dev_err(dev, "Fail to register panic notifier\n"); |
| goto err_destroy_workqueue; |
| } |
| |
| snprintf(name, sizeof(name), KBUILD_MODNAME ".%d_ttyVK", id); |
| err = bcm_vk_tty_init(vk, name); |
| if (err) |
| goto err_unregister_panic_notifier; |
| |
| /* |
| * lets trigger an auto download. We don't want to do it serially here |
| * because at probing time, it is not supposed to block for a long time. |
| */ |
| boot_status = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| if (auto_load) { |
| if ((boot_status & BOOT_STATE_MASK) == BROM_RUNNING) { |
| err = bcm_vk_trigger_autoload(vk); |
| if (err) |
| goto err_bcm_vk_tty_exit; |
| } else { |
| dev_err(dev, |
| "Auto-load skipped - BROM not in proper state (0x%x)\n", |
| boot_status); |
| } |
| } |
| |
| /* enable hb */ |
| bcm_vk_hb_init(vk); |
| |
| dev_dbg(dev, "BCM-VK:%u created\n", id); |
| |
| return 0; |
| |
| err_bcm_vk_tty_exit: |
| bcm_vk_tty_exit(vk); |
| |
| err_unregister_panic_notifier: |
| atomic_notifier_chain_unregister(&panic_notifier_list, |
| &vk->panic_nb); |
| |
| err_destroy_workqueue: |
| destroy_workqueue(vk->wq_thread); |
| |
| err_misc_deregister: |
| misc_deregister(misc_device); |
| |
| err_kfree_name: |
| kfree(misc_device->name); |
| misc_device->name = NULL; |
| |
| err_ida_remove: |
| ida_simple_remove(&bcm_vk_ida, id); |
| |
| err_irq: |
| for (i = 0; i < vk->num_irqs; i++) |
| devm_free_irq(dev, pci_irq_vector(pdev, i), vk); |
| |
| pci_disable_msix(pdev); |
| pci_disable_msi(pdev); |
| |
| err_iounmap: |
| for (i = 0; i < MAX_BAR; i++) { |
| if (vk->bar[i]) |
| pci_iounmap(pdev, vk->bar[i]); |
| } |
| pci_release_regions(pdev); |
| |
| err_disable_pdev: |
| if (vk->tdma_vaddr) |
| dma_free_coherent(&pdev->dev, nr_scratch_pages * PAGE_SIZE, |
| vk->tdma_vaddr, vk->tdma_addr); |
| |
| pci_free_irq_vectors(pdev); |
| pci_disable_device(pdev); |
| pci_dev_put(pdev); |
| |
| err_free_exit: |
| kfree(vk); |
| |
| return err; |
| } |
| |
| void bcm_vk_release_data(struct kref *kref) |
| { |
| struct bcm_vk *vk = container_of(kref, struct bcm_vk, kref); |
| struct pci_dev *pdev = vk->pdev; |
| |
| dev_dbg(&pdev->dev, "BCM-VK:%d release data 0x%p\n", vk->devid, vk); |
| pci_dev_put(pdev); |
| kfree(vk); |
| } |
| |
| static void bcm_vk_remove(struct pci_dev *pdev) |
| { |
| int i; |
| struct bcm_vk *vk = pci_get_drvdata(pdev); |
| struct miscdevice *misc_device = &vk->miscdev; |
| |
| bcm_vk_hb_deinit(vk); |
| |
| /* |
| * Trigger a reset to card and wait enough time for UCODE to rerun, |
| * which re-initialize the card into its default state. |
| * This ensures when driver is re-enumerated it will start from |
| * a completely clean state. |
| */ |
| bcm_vk_trigger_reset(vk); |
| usleep_range(BCM_VK_UCODE_BOOT_US, BCM_VK_UCODE_BOOT_MAX_US); |
| |
| /* unregister panic notifier */ |
| atomic_notifier_chain_unregister(&panic_notifier_list, |
| &vk->panic_nb); |
| |
| bcm_vk_msg_remove(vk); |
| bcm_vk_tty_exit(vk); |
| |
| if (vk->tdma_vaddr) |
| dma_free_coherent(&pdev->dev, nr_scratch_pages * PAGE_SIZE, |
| vk->tdma_vaddr, vk->tdma_addr); |
| |
| /* remove if name is set which means misc dev registered */ |
| if (misc_device->name) { |
| misc_deregister(misc_device); |
| kfree(misc_device->name); |
| ida_simple_remove(&bcm_vk_ida, vk->devid); |
| } |
| for (i = 0; i < vk->num_irqs; i++) |
| devm_free_irq(&pdev->dev, pci_irq_vector(pdev, i), vk); |
| |
| pci_disable_msix(pdev); |
| pci_disable_msi(pdev); |
| |
| cancel_work_sync(&vk->wq_work); |
| destroy_workqueue(vk->wq_thread); |
| bcm_vk_tty_wq_exit(vk); |
| |
| for (i = 0; i < MAX_BAR; i++) { |
| if (vk->bar[i]) |
| pci_iounmap(pdev, vk->bar[i]); |
| } |
| |
| dev_dbg(&pdev->dev, "BCM-VK:%d released\n", vk->devid); |
| |
| pci_release_regions(pdev); |
| pci_free_irq_vectors(pdev); |
| pci_disable_device(pdev); |
| |
| kref_put(&vk->kref, bcm_vk_release_data); |
| } |
| |
| static void bcm_vk_shutdown(struct pci_dev *pdev) |
| { |
| struct bcm_vk *vk = pci_get_drvdata(pdev); |
| u32 reg, boot_stat; |
| |
| reg = vkread32(vk, BAR_0, BAR_BOOT_STATUS); |
| boot_stat = reg & BOOT_STATE_MASK; |
| |
| if (boot_stat == BOOT1_RUNNING) { |
| /* simply trigger a reset interrupt to park it */ |
| bcm_vk_trigger_reset(vk); |
| } else if (boot_stat == BROM_NOT_RUN) { |
| int err; |
| u16 lnksta; |
| |
| /* |
| * The boot status only reflects boot condition since last reset |
| * As ucode will run only once to configure pcie, if multiple |
| * resets happen, we lost track if ucode has run or not. |
| * Here, read the current link speed and use that to |
| * sync up the bootstatus properly so that on reboot-back-up, |
| * it has the proper state to start with autoload |
| */ |
| err = pcie_capability_read_word(pdev, PCI_EXP_LNKSTA, &lnksta); |
| if (!err && |
| (lnksta & PCI_EXP_LNKSTA_CLS) != PCI_EXP_LNKSTA_CLS_2_5GB) { |
| reg |= BROM_STATUS_COMPLETE; |
| vkwrite32(vk, reg, BAR_0, BAR_BOOT_STATUS); |
| } |
| } |
| } |
| |
| static const struct pci_device_id bcm_vk_ids[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_VALKYRIE), }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(pci, bcm_vk_ids); |
| |
| static struct pci_driver pci_driver = { |
| .name = DRV_MODULE_NAME, |
| .id_table = bcm_vk_ids, |
| .probe = bcm_vk_probe, |
| .remove = bcm_vk_remove, |
| .shutdown = bcm_vk_shutdown, |
| }; |
| module_pci_driver(pci_driver); |
| |
| MODULE_DESCRIPTION("Broadcom VK Host Driver"); |
| MODULE_AUTHOR("Scott Branden <scott.branden@broadcom.com>"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_VERSION("1.0"); |