| config ATH6K_LEGACY |
| tristate "Atheros AR6003 support (non mac80211)" |
| depends on MMC && WLAN |
| select WIRELESS_EXT |
| select WEXT_PRIV |
| help |
| This module adds support for wireless adapters based on Atheros AR6003 chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. Pls note that AR6002 and AR6001 are not supported by this driver. |
| |
| choice |
| prompt "AR6003 Board Data Configuration" |
| depends on ATH6K_LEGACY |
| default AR600x_SD31_XXX |
| help |
| Select the appropriate board data template from the list below that matches your AR6003 based reference design. |
| |
| config AR600x_SD31_XXX |
| bool "SD31-xxx" |
| help |
| Board Data file for a standard SD31 reference design (File: bdata.SD31.bin) |
| |
| config AR600x_WB31_XXX |
| bool "WB31-xxx" |
| help |
| Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin) |
| |
| config AR600x_SD32_XXX |
| bool "SD32-xxx" |
| help |
| Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin) |
| |
| config AR600x_CUSTOM_XXX |
| bool "CUSTOM-xxx" |
| help |
| Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin) |
| endchoice |
| |
| config ATH6KL_ENABLE_COEXISTENCE |
| bool "BT Coexistence support" |
| depends on ATH6K_LEGACY |
| help |
| Enables WLAN/BT coexistence support. Select the apprpriate configuration from below. |
| |
| choice |
| prompt "Front-End Antenna Configuration" |
| depends on ATH6KL_ENABLE_COEXISTENCE |
| default AR600x_DUAL_ANTENNA |
| help |
| Indicates the number of antennas being used by BT and WLAN. Select the appropriate configuration from the list below that matches your AR6003 based reference design. |
| |
| config AR600x_DUAL_ANTENNA |
| bool "Dual Antenna" |
| help |
| Dual Antenna Design |
| |
| config AR600x_SINGLE_ANTENNA |
| bool "Single Antenna" |
| help |
| Single Antenna Design |
| endchoice |
| |
| choice |
| prompt "Collocated Bluetooth Type" |
| depends on ATH6KL_ENABLE_COEXISTENCE |
| default AR600x_BT_AR3001 |
| help |
| Select the appropriate configuration from the list below that matches your AR6003 based reference design. |
| |
| config AR600x_BT_QCOM |
| bool "Qualcomm BTS4020X" |
| help |
| Qualcomm BT (3 Wire PTA) |
| |
| config AR600x_BT_CSR |
| bool "CSR BC06" |
| help |
| CSR BT (3 Wire PTA) |
| |
| config AR600x_BT_AR3001 |
| bool "Atheros AR3001" |
| help |
| Atheros BT (3 Wire PTA) |
| endchoice |
| |
| config ATH6KL_HCI_BRIDGE |
| bool "HCI over SDIO support" |
| depends on ATH6K_LEGACY |
| help |
| Enables BT over SDIO. Applicable only for combo designs (eg: WB31) |
| |
| config ATH6KL_CONFIG_GPIO_BT_RESET |
| bool "Configure BT Reset GPIO" |
| depends on ATH6KL_HCI_BRIDGE |
| help |
| Configure a WLAN GPIO for use with BT. |
| |
| config AR600x_BT_RESET_PIN |
| int "GPIO" |
| depends on ATH6KL_CONFIG_GPIO_BT_RESET |
| default 22 |
| help |
| WLAN GPIO to be used for resetting BT |
| |
| config ATH6KL_HTC_RAW_INTERFACE |
| bool "RAW HTC support" |
| depends on ATH6K_LEGACY |
| help |
| Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface |
| |
| config ATH6KL_VIRTUAL_SCATTER_GATHER |
| bool "Virtual Scatter-Gather support" |
| depends on ATH6K_LEGACY |
| help |
| Enables virtual scatter gather support for the hardware that does not support it natively. |
| |
| config ATH6KL_SKIP_ABI_VERSION_CHECK |
| bool "Skip ABI version check support" |
| depends on ATH6K_LEGACY |
| help |
| Forces the driver to disable ABI version check. Caution: Incompatilbity between the host driver and target firmware may lead to unknown side effects. |
| |
| config ATH6KL_BT_UART_FC_POLARITY |
| int "UART Flow Control Polarity" |
| depends on ATH6KL_LEGACY |
| default 0 |
| help |
| Configures the polarity of UART Flow Control. A value of 0 implies active low and is the default setting. Set it to 1 for active high. |
| |
| config ATH6KL_DEBUG |
| bool "Debug support" |
| depends on ATH6K_LEGACY |
| help |
| Enables debug support |
| |
| config ATH6KL_ENABLE_HOST_DEBUG |
| bool "Host Debug support" |
| depends on ATH6KL_DEBUG |
| help |
| Enables debug support in the driver |
| |
| config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS |
| bool "Target Debug support - Enable UART prints" |
| depends on ATH6KL_DEBUG |
| help |
| Enables uart prints |
| |
| config AR600x_DEBUG_UART_TX_PIN |
| int "GPIO" |
| depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS |
| default 8 |
| help |
| WLAN GPIO to be used for Debug UART (Tx) |
| |
| config ATH6KL_DISABLE_TARGET_DBGLOGS |
| bool "Target Debug support - Disable Debug logs" |
| depends on ATH6KL_DEBUG |
| help |
| Enables debug logs |
