| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung's Exynos4412 based Trats 2 board device tree source |
| * |
| * Copyright (c) 2013 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| * |
| * Device tree source file for Samsung's Trats 2 board which is based on |
| * Samsung's Exynos4412 SoC. |
| */ |
| |
| /dts-v1/; |
| #include "exynos4412.dtsi" |
| #include "exynos4412-ppmu-common.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/clock/maxim,max77686.h> |
| #include <dt-bindings/pinctrl/samsung.h> |
| |
| / { |
| compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4"; |
| |
| aliases { |
| i2c11 = &i2c_max77693; |
| i2c12 = &i2c_max77693_fuel; |
| }; |
| |
| chosen { |
| stdout-path = &serial_2; |
| }; |
| |
| firmware@204f000 { |
| compatible = "samsung,secure-firmware"; |
| reg = <0x0204F000 0x1000>; |
| }; |
| |
| fixed-rate-clocks { |
| xxti { |
| compatible = "samsung,clock-xxti"; |
| clock-frequency = <0>; |
| }; |
| |
| xusbxti { |
| compatible = "samsung,clock-xusbxti"; |
| clock-frequency = <24000000>; |
| }; |
| }; |
| |
| cam_io_reg: voltage-regulator-1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "CAM_SENSOR_A"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| enable-active-high; |
| status = "disabled"; |
| }; |
| |
| cam_af_reg: voltage-regulator-2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "CAM_AF"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| enable-active-high; |
| status = "disabled"; |
| }; |
| |
| vsil12: voltage-regulator-3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VSIL_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| vin-supply = <&buck7_reg>; |
| }; |
| |
| vcc33mhl: voltage-regulator-4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_3.3_MHL"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vcc18mhl: voltage-regulator-5 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC_1.8_MHL"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| touchkey_reg: voltage-regulator-6 { |
| compatible = "regulator-fixed"; |
| regulator-name = "LED_VDD_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| enable-active-high; |
| status = "disabled"; |
| }; |
| |
| vbatt_reg: voltage-regulator-7 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VBATT"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| mic_bias_reg: voltage-regulator-8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "MICBIAS_LDO_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| gpio = <&gpf1 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| submic_bias_reg: voltage-regulator-9 { |
| compatible = "regulator-fixed"; |
| regulator-name = "SUB_MICBIAS_LDO_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys>; |
| |
| key-down { |
| gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; |
| linux,code = <114>; |
| label = "volume down"; |
| debounce-interval = <10>; |
| }; |
| |
| key-up { |
| gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; |
| linux,code = <115>; |
| label = "volume up"; |
| debounce-interval = <10>; |
| }; |
| |
| key-power { |
| gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; |
| linux,code = <116>; |
| label = "power"; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| |
| key-ok { |
| gpios = <&gpx0 1 GPIO_ACTIVE_LOW>; |
| linux,code = <139>; |
| label = "ok"; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| }; |
| |
| i2c_max77693: i2c-gpio-1 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmic@66 { |
| compatible = "maxim,max77693"; |
| interrupt-parent = <&gpx1>; |
| interrupts = <5 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&max77693_irq>; |
| reg = <0x66>; |
| |
| regulators { |
| esafeout1_reg: ESAFEOUT1 { |
| regulator-name = "ESAFEOUT1"; |
| }; |
| esafeout2_reg: ESAFEOUT2 { |
| regulator-name = "ESAFEOUT2"; |
| }; |
| charger_reg: CHARGER { |
| regulator-name = "CHARGER"; |
| regulator-min-microamp = <60000>; |
| regulator-max-microamp = <2580000>; |
| }; |
| }; |
| |
| motor-driver { |
| compatible = "maxim,max77693-haptic"; |
| haptic-supply = <&ldo26_reg>; |
| pwms = <&pwm 0 38022 0>; |
| }; |
| |
| charger { |
| compatible = "maxim,max77693-charger"; |
| |
| maxim,constant-microvolt = <4350000>; |
| maxim,min-system-microvolt = <3600000>; |
| maxim,thermal-regulation-celsius = <100>; |
| maxim,battery-overcurrent-microamp = <3500000>; |
| maxim,charge-input-threshold-microvolt = <4300000>; |
| }; |
| }; |
| }; |
| |
| i2c_max77693_fuel: i2c-gpio-3 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpf1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpf1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| fuel-gauge@36 { |
| compatible = "maxim,max17047"; |
| interrupt-parent = <&gpx2>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&max77693_fuel_irq>; |
| reg = <0x36>; |
| |
| maxim,over-heat-temp = <700>; |
| maxim,over-volt = <4500>; |
| }; |
| }; |
| |
| i2c-gpio-4 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| touchkey@20 { |
| compatible = "cypress,midas-touchkey"; |
| reg = <0x20>; |
| vdd-supply = <&touchkey_reg>; |
| vcc-supply = <&ldo5_reg>; |
| interrupt-parent = <&gpj0>; |
| interrupts = <3 IRQ_TYPE_EDGE_FALLING>; |
| linux,keycodes = <KEY_BACK KEY_MENU>; |
| }; |
| }; |
| |
| i2c-mhl { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpf0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpf0 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-0 = <&i2c_mhl_bus>; |
| pinctrl-names = "default"; |
| |
| sii9234: hdmi-bridge@39 { |
| compatible = "sil,sii9234"; |
| avcc33-supply = <&vcc33mhl>; |
| iovcc18-supply = <&vcc18mhl>; |
| avcc12-supply = <&vsil12>; |
| cvcc12-supply = <&vsil12>; |
| reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>; |
| interrupt-parent = <&gpf3>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x39>; |
| |
| port { |
| mhl_to_hdmi: endpoint { |
| remote-endpoint = <&hdmi_to_mhl>; |
| }; |
| }; |
| }; |
| }; |
| |
| wlan_pwrseq: sdhci3-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>; |
| clocks = <&max77686 MAX77686_CLK_PMIC>; |
| clock-names = "ext_clock"; |
| }; |
| |
| sound: sound { |
| compatible = "samsung,midas-audio"; |
| model = "Midas"; |
| mic-bias-supply = <&mic_bias_reg>; |
| submic-bias-supply = <&submic_bias_reg>; |
| |
| cpu { |
| sound-dai = <&i2s0 0>; |
| }; |
| codec { |
| sound-dai = <&wm1811>; |
| }; |
| }; |
| |
| thermistor-ap { |
| compatible = "murata,ncp15wb473"; |
| pullup-uv = <1800000>; /* VCC_1.8V_AP */ |
| pullup-ohm = <100000>; /* 100K */ |
| pulldown-ohm = <100000>; /* 100K */ |
| io-channels = <&adc 1>; /* AP temperature */ |
| }; |
| |
| thermistor-battery { |
| compatible = "murata,ncp15wb473"; |
| pullup-uv = <1800000>; /* VCC_1.8V_AP */ |
| pullup-ohm = <100000>; /* 100K */ |
| pulldown-ohm = <100000>; /* 100K */ |
| io-channels = <&adc 2>; /* Battery temperature */ |
| }; |
| }; |
| |
| &adc { |
| vdd-supply = <&ldo3_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_dmc { |
| devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; |
| vdd-supply = <&buck1_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_acp { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_c2c { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_leftbus { |
| devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; |
| vdd-supply = <&buck3_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_rightbus { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_display { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_fsys { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_peri { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_mfc { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &camera { |
| pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| assigned-clocks = <&clock CLK_MOUT_CAM0>, |
| <&clock CLK_MOUT_CAM1>; |
| assigned-clock-parents = <&clock CLK_XUSBXTI>, |
| <&clock CLK_XUSBXTI>; |
| }; |
| |
| &cpu0 { |
| cpu0-supply = <&buck2_reg>; |
| }; |
| |
| &cpu_thermal { |
| cooling-maps { |
| map0 { |
| /* Corresponds to 800MHz at freq_table */ |
| cooling-device = <&cpu0 7 7>, <&cpu1 7 7>, |
| <&cpu2 7 7>, <&cpu3 7 7>; |
| }; |
| map1 { |
| /* Corresponds to 200MHz at freq_table */ |
| cooling-device = <&cpu0 13 13>, <&cpu1 13 13>, |
| <&cpu2 13 13>, <&cpu3 13 13>; |
| }; |
| }; |
| }; |
| |
| &csis_0 { |
| status = "okay"; |
| vddcore-supply = <&ldo8_reg>; |
| vddio-supply = <&ldo10_reg>; |
| assigned-clocks = <&clock CLK_MOUT_CSIS0>, |
| <&clock CLK_SCLK_CSIS0>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| |
| /* Camera C (3) MIPI CSI-2 (CSIS0) */ |
| port@3 { |
| reg = <3>; |
| csis0_ep: endpoint { |
| remote-endpoint = <&s5c73m3_ep>; |
| data-lanes = <1 2 3 4>; |
| samsung,csis-hs-settle = <12>; |
| }; |
| }; |
| }; |
| |
| &csis_1 { |
| status = "okay"; |
| vddcore-supply = <&ldo8_reg>; |
| vddio-supply = <&ldo10_reg>; |
| assigned-clocks = <&clock CLK_MOUT_CSIS1>, |
| <&clock CLK_SCLK_CSIS1>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| |
| /* Camera D (4) MIPI CSI-2 (CSIS1) */ |
| port@4 { |
| reg = <4>; |
| csis1_ep: endpoint { |
| remote-endpoint = <&is_s5k6a3_ep>; |
| data-lanes = <1>; |
| samsung,csis-hs-settle = <18>; |
| samsung,csis-wclk; |
| }; |
| }; |
| }; |
| |
| &dsi_0 { |
| vddcore-supply = <&ldo8_reg>; |
| vddio-supply = <&ldo10_reg>; |
| samsung,burst-clock-frequency = <500000000>; |
| samsung,esc-clock-frequency = <20000000>; |
| samsung,pll-clock-frequency = <24000000>; |
| }; |
| |
| &exynos_usbphy { |
| vbus-supply = <&esafeout1_reg>; |
| status = "okay"; |
| }; |
| |
| &fimc_0 { |
| status = "okay"; |
| assigned-clocks = <&clock CLK_MOUT_FIMC0>, |
| <&clock CLK_SCLK_FIMC0>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| }; |
| |
| &fimc_1 { |
| status = "okay"; |
| assigned-clocks = <&clock CLK_MOUT_FIMC1>, |
| <&clock CLK_SCLK_FIMC1>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| }; |
| |
| &fimc_2 { |
| status = "okay"; |
| assigned-clocks = <&clock CLK_MOUT_FIMC2>, |
| <&clock CLK_SCLK_FIMC2>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| }; |
| |
| &fimc_3 { |
| status = "okay"; |
| assigned-clocks = <&clock CLK_MOUT_FIMC3>, |
| <&clock CLK_SCLK_FIMC3>; |
| assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>; |
| assigned-clock-rates = <0>, <176000000>; |
| }; |
| |
| &fimc_is { |
| pinctrl-0 = <&fimc_is_uart>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| }; |
| |
| &fimc_lite_0 { |
| status = "okay"; |
| }; |
| |
| &fimc_lite_1 { |
| status = "okay"; |
| }; |
| |
| &fimd { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| mali-supply = <&buck4_reg>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hdmi_hpd>; |
| vdd-supply = <&ldo3_reg>; |
| vdd_osc-supply = <&ldo4_reg>; |
| vdd_pll-supply = <&ldo3_reg>; |
| ddc = <&i2c_5>; |
| status = "okay"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| hdmi_to_mhl: endpoint { |
| remote-endpoint = <&mhl_to_hdmi>; |
| }; |
| }; |
| }; |
| }; |
| |
| &hsotg { |
| vusb_d-supply = <&ldo15_reg>; |
| vusb_a-supply = <&ldo12_reg>; |
| dr_mode = "peripheral"; |
| status = "okay"; |
| }; |
| |
| &i2c_0 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c0_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| s5c73m3: image-sensor@3c { |
| compatible = "samsung,s5c73m3"; |
| reg = <0x3c>; |
| xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */ |
| vdd-int-supply = <&buck9_reg>; |
| vddio-cis-supply = <&ldo9_reg>; |
| vddio-host-supply = <&ldo18_reg>; |
| vdd-af-supply = <&cam_af_reg>; |
| vdd-reg-supply = <&cam_io_reg>; |
| clock-frequency = <24000000>; |
| /* CAM_A_CLKOUT */ |
| clocks = <&camera 0>; |
| clock-names = "cis_extclk"; |
| status = "disabled"; |
| port { |
| s5c73m3_ep: endpoint { |
| remote-endpoint = <&csis0_ep>; |
| data-lanes = <1 2 3 4>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c1_isp { |
| pinctrl-0 = <&fimc_is_i2c1>; |
| pinctrl-names = "default"; |
| |
| image-sensor@10 { |
| compatible = "samsung,s5k6a3"; |
| reg = <0x10>; |
| svdda-supply = <&cam_io_reg>; |
| svddio-supply = <&ldo19_reg>; |
| afvdd-supply = <&ldo19_reg>; |
| clock-frequency = <24000000>; |
| /* CAM_B_CLKOUT */ |
| clocks = <&camera 1>; |
| clock-names = "extclk"; |
| samsung,camclk-out = <1>; |
| gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>; |
| |
| port { |
| is_s5k6a3_ep: endpoint { |
| remote-endpoint = <&csis1_ep>; |
| data-lanes = <1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c_3 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c3_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &i2c_4 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <100000>; |
| pinctrl-0 = <&i2c4_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| wm1811: audio-codec@1a { |
| compatible = "wlf,wm1811"; |
| reg = <0x1a>; |
| clocks = <&pmu_system_controller 0>, |
| <&max77686 MAX77686_CLK_PMIC>; |
| clock-names = "MCLK1", "MCLK2"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&gpx3>; |
| interrupts = <6 IRQ_TYPE_LEVEL_HIGH>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| #sound-dai-cells = <0>; |
| |
| wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0 |
| 0x0 0x8000 0x0 0x0 0x0>; |
| wlf,micbias-cfg = <0x2f 0x2b>; |
| |
| wlf,lineout1-feedback; |
| wlf,lineout1-se; |
| wlf,lineout2-se; |
| wlf,ldoena-always-driven; |
| |
| AVDD2-supply = <&vbatt_reg>; |
| DBVDD1-supply = <&ldo3_reg>; |
| DBVDD2-supply = <&vbatt_reg>; |
| DBVDD3-supply = <&vbatt_reg>; |
| DCVDD-supply = <&ldo3_reg>; |
| CPVDD-supply = <&vbatt_reg>; |
| SPKVDD1-supply = <&vbatt_reg>; |
| SPKVDD2-supply = <&vbatt_reg>; |
| wlf,ldo1ena = <&gpj0 4 0>; |
| wlf,ldo2ena = <&gpj0 4 0>; |
| }; |
| }; |
| |
| &i2c_5 { |
| status = "okay"; |
| }; |
| |
| &i2c_7 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <100000>; |
| pinctrl-0 = <&i2c7_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| max77686: pmic@9 { |
| compatible = "maxim,max77686"; |
| interrupt-parent = <&gpx0>; |
| interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-0 = <&max77686_irq>; |
| pinctrl-names = "default"; |
| wakeup-source; |
| reg = <0x09>; |
| #clock-cells = <1>; |
| |
| voltage-regulators { |
| ldo1_reg: LDO1 { |
| regulator-name = "VALIVE_1.0V_AP"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "VM1M2_1.2V_AP"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "VCC_1.8V_AP"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "VCC_2.8V_AP"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-always-on; |
| }; |
| |
| ldo5_reg: LDO5 { |
| regulator-name = "VCC_1.8V_IO"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "VMPLL_1.0V_AP"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo7_reg: LDO7 { |
| regulator-name = "VPLL_1.0V_AP"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo8_reg: LDO8 { |
| regulator-name = "VMIPI_1.0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo9_reg: LDO9 { |
| regulator-name = "CAM_ISP_MIPI_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| ldo10_reg: LDO10 { |
| regulator-name = "VMIPI_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo11_reg: LDO11 { |
| regulator-name = "VABB1_1.95V"; |
| regulator-min-microvolt = <1950000>; |
| regulator-max-microvolt = <1950000>; |
| regulator-always-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo12_reg: LDO12 { |
| regulator-name = "VUOTG_3.0V"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo13_reg: LDO13 { |
| regulator-name = "NFC_AVDD_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| ldo14_reg: LDO14 { |
| regulator-name = "VABB2_1.95V"; |
| regulator-min-microvolt = <1950000>; |
| regulator-max-microvolt = <1950000>; |
| regulator-always-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo15_reg: LDO15 { |
| regulator-name = "VHSIC_1.0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo16_reg: LDO16 { |
| regulator-name = "VHSIC_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo17_reg: LDO17 { |
| regulator-name = "CAM_SENSOR_CORE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| ldo18_reg: LDO18 { |
| regulator-name = "CAM_ISP_SEN_IO_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| ldo19_reg: LDO19 { |
| regulator-name = "VT_CAM_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| ldo20_reg: LDO20 { |
| regulator-name = "VDDQ_PRE_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| ldo21_reg: LDO21 { |
| regulator-name = "VTF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| ldo22_reg: LDO22 { |
| regulator-name = "VMEM_VDD_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| ldo23_reg: LDO23 { |
| regulator-name = "TSP_AVDD_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| ldo24_reg: LDO24 { |
| regulator-name = "TSP_VDD_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| ldo25_reg: LDO25 { |
| regulator-name = "LDO25"; |
| }; |
| |
| ldo26_reg: LDO26 { |
| regulator-name = "MOTOR_VCC_3.0V"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| buck1_reg: BUCK1 { |
| regulator-name = "VDD_MIF"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "VDD_ARM"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| buck3_reg: BUCK3 { |
| regulator-name = "VDD_INT"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| buck4_reg: BUCK4 { |
| regulator-name = "VDD_G3D"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| buck5_reg: BUCK5 { |
| regulator-name = "VMEM_1.2V_AP"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| }; |
| |
| buck6_reg: BUCK6 { |
| regulator-name = "VCC_SUB_1.35V"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-always-on; |
| }; |
| |
| buck7_reg: BUCK7 { |
| regulator-name = "VCC_SUB_2.0V"; |
| regulator-min-microvolt = <2000000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-always-on; |
| }; |
| |
| buck8_reg: BUCK8 { |
| regulator-name = "VMEM_VDDF_3.0V"; |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| buck9_reg: BUCK9 { |
| regulator-name = "CAM_ISP_CORE_1.2V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c_8 { |
| status = "okay"; |
| }; |
| |
| &i2s0 { |
| pinctrl-0 = <&i2s0_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &mixer { |
| status = "okay"; |
| }; |
| |
| &mshc_0 { |
| broken-cd; |
| non-removable; |
| card-detect-delay = <200>; |
| vmmc-supply = <&ldo22_reg>; |
| clock-frequency = <400000000>; |
| samsung,dw-mshc-ciu-div = <0>; |
| samsung,dw-mshc-sdr-timing = <2 3>; |
| samsung,dw-mshc-ddr-timing = <1 2>; |
| pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| }; |
| |
| &pmu_system_controller { |
| assigned-clocks = <&pmu_system_controller 0>; |
| assigned-clock-parents = <&clock CLK_XUSBXTI>; |
| }; |
| |
| &pinctrl_0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep0>; |
| |
| mhl_int: mhl-int { |
| samsung,pins = "gpf3-5"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| i2c_mhl_bus: i2c-mhl-bus { |
| samsung,pins = "gpf0-4", "gpf0-6"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_2>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| sleep0: sleep-states { |
| PIN_SLP(gpa0-0, INPUT, NONE); |
| PIN_SLP(gpa0-1, OUT0, NONE); |
| PIN_SLP(gpa0-2, INPUT, NONE); |
| PIN_SLP(gpa0-3, INPUT, UP); |
| PIN_SLP(gpa0-4, INPUT, NONE); |
| PIN_SLP(gpa0-5, INPUT, DOWN); |
| PIN_SLP(gpa0-6, INPUT, DOWN); |
| PIN_SLP(gpa0-7, INPUT, UP); |
| |
| PIN_SLP(gpa1-0, INPUT, DOWN); |
| PIN_SLP(gpa1-1, INPUT, DOWN); |
| PIN_SLP(gpa1-2, INPUT, DOWN); |
| PIN_SLP(gpa1-3, INPUT, DOWN); |
| PIN_SLP(gpa1-4, INPUT, DOWN); |
| PIN_SLP(gpa1-5, INPUT, DOWN); |
| |
| PIN_SLP(gpb-0, INPUT, NONE); |
| PIN_SLP(gpb-1, INPUT, NONE); |
| PIN_SLP(gpb-2, INPUT, NONE); |
| PIN_SLP(gpb-3, INPUT, NONE); |
| PIN_SLP(gpb-4, INPUT, DOWN); |
| PIN_SLP(gpb-5, INPUT, UP); |
| PIN_SLP(gpb-6, INPUT, DOWN); |
| PIN_SLP(gpb-7, INPUT, DOWN); |
| |
| PIN_SLP(gpc0-0, INPUT, DOWN); |
| PIN_SLP(gpc0-1, INPUT, DOWN); |
| PIN_SLP(gpc0-2, INPUT, DOWN); |
| PIN_SLP(gpc0-3, INPUT, DOWN); |
| PIN_SLP(gpc0-4, INPUT, DOWN); |
| |
| PIN_SLP(gpc1-0, INPUT, NONE); |
| PIN_SLP(gpc1-1, PREV, NONE); |
| PIN_SLP(gpc1-2, INPUT, NONE); |
| PIN_SLP(gpc1-3, INPUT, NONE); |
| PIN_SLP(gpc1-4, INPUT, NONE); |
| |
| PIN_SLP(gpd0-0, INPUT, DOWN); |
| PIN_SLP(gpd0-1, INPUT, DOWN); |
| PIN_SLP(gpd0-2, INPUT, NONE); |
| PIN_SLP(gpd0-3, INPUT, NONE); |
| |
| PIN_SLP(gpd1-0, INPUT, DOWN); |
| PIN_SLP(gpd1-1, INPUT, DOWN); |
| PIN_SLP(gpd1-2, INPUT, NONE); |
| PIN_SLP(gpd1-3, INPUT, NONE); |
| |
| PIN_SLP(gpf0-0, INPUT, NONE); |
| PIN_SLP(gpf0-1, INPUT, NONE); |
| PIN_SLP(gpf0-2, INPUT, DOWN); |
| PIN_SLP(gpf0-3, INPUT, DOWN); |
| PIN_SLP(gpf0-4, INPUT, NONE); |
| PIN_SLP(gpf0-5, INPUT, DOWN); |
| PIN_SLP(gpf0-6, INPUT, NONE); |
| PIN_SLP(gpf0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpf1-0, INPUT, DOWN); |
| PIN_SLP(gpf1-1, INPUT, DOWN); |
| PIN_SLP(gpf1-2, INPUT, DOWN); |
| PIN_SLP(gpf1-3, INPUT, DOWN); |
| PIN_SLP(gpf1-4, INPUT, NONE); |
| PIN_SLP(gpf1-5, INPUT, NONE); |
| PIN_SLP(gpf1-6, INPUT, DOWN); |
| PIN_SLP(gpf1-7, PREV, NONE); |
| |
| PIN_SLP(gpf2-0, PREV, NONE); |
| PIN_SLP(gpf2-1, INPUT, DOWN); |
| PIN_SLP(gpf2-2, INPUT, DOWN); |
| PIN_SLP(gpf2-3, INPUT, DOWN); |
| PIN_SLP(gpf2-4, INPUT, DOWN); |
| PIN_SLP(gpf2-5, INPUT, DOWN); |
| PIN_SLP(gpf2-6, INPUT, NONE); |
| PIN_SLP(gpf2-7, INPUT, NONE); |
| |
| PIN_SLP(gpf3-0, INPUT, NONE); |
| PIN_SLP(gpf3-1, PREV, NONE); |
| PIN_SLP(gpf3-2, PREV, NONE); |
| PIN_SLP(gpf3-3, PREV, NONE); |
| PIN_SLP(gpf3-4, OUT1, NONE); |
| PIN_SLP(gpf3-5, INPUT, DOWN); |
| |
| PIN_SLP(gpj0-0, PREV, NONE); |
| PIN_SLP(gpj0-1, PREV, NONE); |
| PIN_SLP(gpj0-2, PREV, NONE); |
| PIN_SLP(gpj0-3, INPUT, DOWN); |
| PIN_SLP(gpj0-4, PREV, NONE); |
| PIN_SLP(gpj0-5, PREV, NONE); |
| PIN_SLP(gpj0-6, INPUT, DOWN); |
| PIN_SLP(gpj0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpj1-0, INPUT, DOWN); |
| PIN_SLP(gpj1-1, PREV, NONE); |
| PIN_SLP(gpj1-2, PREV, NONE); |
| PIN_SLP(gpj1-3, INPUT, DOWN); |
| PIN_SLP(gpj1-4, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep1>; |
| |
| gpio_keys: gpio-keys { |
| samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_shutdown: bt-shutdown { |
| samsung,pins = "gpl0-6"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_host_wakeup: bt-host-wakeup { |
| samsung,pins = "gpx2-6"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_device_wakeup: bt-device-wakeup { |
| samsung,pins = "gpx3-1"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| max77686_irq: max77686-irq { |
| samsung,pins = "gpx0-7"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| max77693_irq: max77693-irq { |
| samsung,pins = "gpx1-5"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| max77693_fuel_irq: max77693-fuel-irq { |
| samsung,pins = "gpx2-3"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| sdhci2_cd: sdhci2-cd-irq { |
| samsung,pins = "gpx3-4"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| hdmi_hpd: hdmi-hpd { |
| samsung,pins = "gpx3-7"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| }; |
| |
| sleep1: sleep-states { |
| PIN_SLP(gpk0-0, PREV, NONE); |
| PIN_SLP(gpk0-1, PREV, NONE); |
| PIN_SLP(gpk0-2, OUT0, NONE); |
| PIN_SLP(gpk0-3, PREV, NONE); |
| PIN_SLP(gpk0-4, PREV, NONE); |
| PIN_SLP(gpk0-5, PREV, NONE); |
| PIN_SLP(gpk0-6, PREV, NONE); |
| |
| PIN_SLP(gpk1-0, INPUT, DOWN); |
| PIN_SLP(gpk1-1, INPUT, DOWN); |
| PIN_SLP(gpk1-2, INPUT, DOWN); |
| PIN_SLP(gpk1-3, PREV, NONE); |
| PIN_SLP(gpk1-4, PREV, NONE); |
| PIN_SLP(gpk1-5, PREV, NONE); |
| PIN_SLP(gpk1-6, PREV, NONE); |
| |
| PIN_SLP(gpk2-0, INPUT, DOWN); |
| PIN_SLP(gpk2-1, INPUT, DOWN); |
| PIN_SLP(gpk2-2, INPUT, DOWN); |
| PIN_SLP(gpk2-3, INPUT, DOWN); |
| PIN_SLP(gpk2-4, INPUT, DOWN); |
| PIN_SLP(gpk2-5, INPUT, DOWN); |
| PIN_SLP(gpk2-6, INPUT, DOWN); |
| |
| PIN_SLP(gpk3-0, OUT0, NONE); |
| PIN_SLP(gpk3-1, INPUT, NONE); |
| PIN_SLP(gpk3-2, INPUT, DOWN); |
| PIN_SLP(gpk3-3, INPUT, NONE); |
| PIN_SLP(gpk3-4, INPUT, NONE); |
| PIN_SLP(gpk3-5, INPUT, NONE); |
| PIN_SLP(gpk3-6, INPUT, NONE); |
| |
| PIN_SLP(gpl0-0, INPUT, DOWN); |
| PIN_SLP(gpl0-1, INPUT, DOWN); |
| PIN_SLP(gpl0-2, INPUT, DOWN); |
| PIN_SLP(gpl0-3, INPUT, DOWN); |
| PIN_SLP(gpl0-4, PREV, NONE); |
| PIN_SLP(gpl0-6, PREV, NONE); |
| |
| PIN_SLP(gpl1-0, INPUT, DOWN); |
| PIN_SLP(gpl1-1, INPUT, DOWN); |
| PIN_SLP(gpl2-0, INPUT, DOWN); |
| PIN_SLP(gpl2-1, INPUT, DOWN); |
| PIN_SLP(gpl2-2, INPUT, DOWN); |
| PIN_SLP(gpl2-3, INPUT, DOWN); |
| PIN_SLP(gpl2-4, INPUT, DOWN); |
| PIN_SLP(gpl2-5, INPUT, DOWN); |
| PIN_SLP(gpl2-6, PREV, NONE); |
| PIN_SLP(gpl2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpm0-0, INPUT, DOWN); |
| PIN_SLP(gpm0-1, INPUT, DOWN); |
| PIN_SLP(gpm0-2, INPUT, DOWN); |
| PIN_SLP(gpm0-3, INPUT, DOWN); |
| PIN_SLP(gpm0-4, INPUT, DOWN); |
| PIN_SLP(gpm0-5, INPUT, DOWN); |
| PIN_SLP(gpm0-6, INPUT, DOWN); |
| PIN_SLP(gpm0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpm1-0, INPUT, DOWN); |
| PIN_SLP(gpm1-1, INPUT, DOWN); |
| PIN_SLP(gpm1-2, INPUT, NONE); |
| PIN_SLP(gpm1-3, INPUT, NONE); |
| PIN_SLP(gpm1-4, INPUT, NONE); |
| PIN_SLP(gpm1-5, INPUT, NONE); |
| PIN_SLP(gpm1-6, INPUT, DOWN); |
| |
| PIN_SLP(gpm2-0, INPUT, NONE); |
| PIN_SLP(gpm2-1, INPUT, NONE); |
| PIN_SLP(gpm2-2, INPUT, DOWN); |
| PIN_SLP(gpm2-3, INPUT, DOWN); |
| PIN_SLP(gpm2-4, INPUT, DOWN); |
| |
| PIN_SLP(gpm3-0, PREV, NONE); |
| PIN_SLP(gpm3-1, PREV, NONE); |
| PIN_SLP(gpm3-2, PREV, NONE); |
| PIN_SLP(gpm3-3, OUT1, NONE); |
| PIN_SLP(gpm3-4, INPUT, DOWN); |
| PIN_SLP(gpm3-5, INPUT, DOWN); |
| PIN_SLP(gpm3-6, INPUT, DOWN); |
| PIN_SLP(gpm3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpm4-0, INPUT, DOWN); |
| PIN_SLP(gpm4-1, INPUT, DOWN); |
| PIN_SLP(gpm4-2, INPUT, DOWN); |
| PIN_SLP(gpm4-3, INPUT, DOWN); |
| PIN_SLP(gpm4-4, INPUT, DOWN); |
| PIN_SLP(gpm4-5, INPUT, DOWN); |
| PIN_SLP(gpm4-6, INPUT, DOWN); |
| PIN_SLP(gpm4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy0-0, INPUT, DOWN); |
| PIN_SLP(gpy0-1, INPUT, DOWN); |
| PIN_SLP(gpy0-2, INPUT, DOWN); |
| PIN_SLP(gpy0-3, INPUT, DOWN); |
| PIN_SLP(gpy0-4, INPUT, DOWN); |
| PIN_SLP(gpy0-5, INPUT, DOWN); |
| |
| PIN_SLP(gpy1-0, INPUT, DOWN); |
| PIN_SLP(gpy1-1, INPUT, DOWN); |
| PIN_SLP(gpy1-2, INPUT, DOWN); |
| PIN_SLP(gpy1-3, INPUT, DOWN); |
| |
| PIN_SLP(gpy2-0, PREV, NONE); |
| PIN_SLP(gpy2-1, INPUT, DOWN); |
| PIN_SLP(gpy2-2, INPUT, NONE); |
| PIN_SLP(gpy2-3, INPUT, NONE); |
| PIN_SLP(gpy2-4, INPUT, NONE); |
| PIN_SLP(gpy2-5, INPUT, NONE); |
| |
| PIN_SLP(gpy3-0, INPUT, DOWN); |
| PIN_SLP(gpy3-1, INPUT, DOWN); |
| PIN_SLP(gpy3-2, INPUT, DOWN); |
| PIN_SLP(gpy3-3, INPUT, DOWN); |
| PIN_SLP(gpy3-4, INPUT, DOWN); |
| PIN_SLP(gpy3-5, INPUT, DOWN); |
| PIN_SLP(gpy3-6, INPUT, DOWN); |
| PIN_SLP(gpy3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy4-0, INPUT, DOWN); |
| PIN_SLP(gpy4-1, INPUT, DOWN); |
| PIN_SLP(gpy4-2, INPUT, DOWN); |
| PIN_SLP(gpy4-3, INPUT, DOWN); |
| PIN_SLP(gpy4-4, INPUT, DOWN); |
| PIN_SLP(gpy4-5, INPUT, DOWN); |
| PIN_SLP(gpy4-6, INPUT, DOWN); |
| PIN_SLP(gpy4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy5-0, INPUT, DOWN); |
| PIN_SLP(gpy5-1, INPUT, DOWN); |
| PIN_SLP(gpy5-2, INPUT, DOWN); |
| PIN_SLP(gpy5-3, INPUT, DOWN); |
| PIN_SLP(gpy5-4, INPUT, DOWN); |
| PIN_SLP(gpy5-5, INPUT, DOWN); |
| PIN_SLP(gpy5-6, INPUT, DOWN); |
| PIN_SLP(gpy5-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy6-0, INPUT, DOWN); |
| PIN_SLP(gpy6-1, INPUT, DOWN); |
| PIN_SLP(gpy6-2, INPUT, DOWN); |
| PIN_SLP(gpy6-3, INPUT, DOWN); |
| PIN_SLP(gpy6-4, INPUT, DOWN); |
| PIN_SLP(gpy6-5, INPUT, DOWN); |
| PIN_SLP(gpy6-6, INPUT, DOWN); |
| PIN_SLP(gpy6-7, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep2>; |
| |
| sleep2: sleep-states { |
| PIN_SLP(gpz-0, INPUT, DOWN); |
| PIN_SLP(gpz-1, INPUT, DOWN); |
| PIN_SLP(gpz-2, INPUT, DOWN); |
| PIN_SLP(gpz-3, INPUT, DOWN); |
| PIN_SLP(gpz-4, INPUT, DOWN); |
| PIN_SLP(gpz-5, INPUT, DOWN); |
| PIN_SLP(gpz-6, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep3>; |
| |
| sleep3: sleep-states { |
| PIN_SLP(gpv0-0, INPUT, DOWN); |
| PIN_SLP(gpv0-1, INPUT, DOWN); |
| PIN_SLP(gpv0-2, INPUT, DOWN); |
| PIN_SLP(gpv0-3, INPUT, DOWN); |
| PIN_SLP(gpv0-4, INPUT, DOWN); |
| PIN_SLP(gpv0-5, INPUT, DOWN); |
| PIN_SLP(gpv0-6, INPUT, DOWN); |
| PIN_SLP(gpv0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv1-0, INPUT, DOWN); |
| PIN_SLP(gpv1-1, INPUT, DOWN); |
| PIN_SLP(gpv1-2, INPUT, DOWN); |
| PIN_SLP(gpv1-3, INPUT, DOWN); |
| PIN_SLP(gpv1-4, INPUT, DOWN); |
| PIN_SLP(gpv1-5, INPUT, DOWN); |
| PIN_SLP(gpv1-6, INPUT, DOWN); |
| PIN_SLP(gpv1-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv2-0, INPUT, DOWN); |
| PIN_SLP(gpv2-1, INPUT, DOWN); |
| PIN_SLP(gpv2-2, INPUT, DOWN); |
| PIN_SLP(gpv2-3, INPUT, DOWN); |
| PIN_SLP(gpv2-4, INPUT, DOWN); |
| PIN_SLP(gpv2-5, INPUT, DOWN); |
| PIN_SLP(gpv2-6, INPUT, DOWN); |
| PIN_SLP(gpv2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv3-0, INPUT, DOWN); |
| PIN_SLP(gpv3-1, INPUT, DOWN); |
| PIN_SLP(gpv3-2, INPUT, DOWN); |
| PIN_SLP(gpv3-3, INPUT, DOWN); |
| PIN_SLP(gpv3-4, INPUT, DOWN); |
| PIN_SLP(gpv3-5, INPUT, DOWN); |
| PIN_SLP(gpv3-6, INPUT, DOWN); |
| PIN_SLP(gpv3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv4-0, INPUT, DOWN); |
| }; |
| }; |
| |
| &pwm { |
| pinctrl-0 = <&pwm0_out>; |
| pinctrl-names = "default"; |
| samsung,pwm-outputs = <0>; |
| status = "okay"; |
| }; |
| |
| &rtc { |
| status = "okay"; |
| clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; |
| clock-names = "rtc", "rtc_src"; |
| }; |
| |
| &sdhci_2 { |
| bus-width = <4>; |
| cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; |
| pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; |
| pinctrl-names = "default"; |
| vmmc-supply = <&ldo21_reg>; |
| status = "okay"; |
| }; |
| |
| &sdhci_3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| non-removable; |
| bus-width = <4>; |
| |
| mmc-pwrseq = <&wlan_pwrseq>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; |
| status = "okay"; |
| |
| brcmf: wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| interrupt-parent = <&gpx2>; |
| interrupts = <5 IRQ_TYPE_NONE>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &serial_0 { |
| pinctrl-0 = <&uart0_data &uart0_fctl>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4330-bt"; |
| pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; |
| pinctrl-names = "default"; |
| max-speed = <3000000>; |
| shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; |
| host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; |
| clocks = <&max77686 MAX77686_CLK_PMIC>; |
| }; |
| }; |
| |
| &serial_1 { |
| status = "okay"; |
| }; |
| |
| &serial_2 { |
| status = "okay"; |
| }; |
| |
| &serial_3 { |
| status = "okay"; |
| }; |
| |
| &spi_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi1_bus>; |
| cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| s5c73m3_spi: image-sensor@0 { |
| compatible = "samsung,s5c73m3"; |
| spi-max-frequency = <50000000>; |
| reg = <0>; |
| controller-data { |
| samsung,spi-feedback-delay = <2>; |
| }; |
| }; |
| }; |
| |
| &tmu { |
| vtmu-supply = <&ldo10_reg>; |
| status = "okay"; |
| }; |
