| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright 2013 Gateworks Corporation |
| */ |
| |
| /dts-v1/; |
| #include <dt-bindings/gpio/gpio.h> |
| #include "imx6q.dtsi" |
| |
| / { |
| model = "Gateworks Ventana GW5400-A"; |
| compatible = "gw,imx6q-gw5400-a", "gw,ventana", "fsl,imx6q"; |
| |
| /* these are used by bootloader for disabling nodes */ |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| led0 = &led0; |
| led1 = &led1; |
| led2 = &led2; |
| ssi0 = &ssi1; |
| spi0 = &ecspi1; |
| usb0 = &usbh1; |
| usb1 = &usbotg; |
| }; |
| |
| chosen { |
| bootargs = "console=ttymxc1,115200"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| |
| led0: user1 { |
| label = "user1"; |
| gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 -> MX6_PANLEDG */ |
| default-state = "on"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led1: user2 { |
| label = "user2"; |
| gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* 106 -> MX6_PANLEDR */ |
| default-state = "off"; |
| }; |
| |
| led2: user3 { |
| label = "user3"; |
| gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* 111 -> MX6_LOCLED# */ |
| default-state = "off"; |
| }; |
| }; |
| |
| memory@10000000 { |
| device_type = "memory"; |
| reg = <0x10000000 0x40000000>; |
| }; |
| |
| pps { |
| compatible = "pps-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| reg_1p0v: regulator@0 { |
| compatible = "regulator-fixed"; |
| reg = <0>; |
| regulator-name = "1P0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| }; |
| |
| reg_3p3v: regulator@1 { |
| compatible = "regulator-fixed"; |
| reg = <1>; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_h1_vbus: regulator@2 { |
| compatible = "regulator-fixed"; |
| reg = <2>; |
| regulator-name = "usb_h1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| reg_usb_otg_vbus: regulator@3 { |
| compatible = "regulator-fixed"; |
| reg = <3>; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| sound { |
| compatible = "fsl,imx6q-ventana-sgtl5000", |
| "fsl,imx-audio-sgtl5000"; |
| model = "sgtl5000-audio"; |
| ssi-controller = <&ssi1>; |
| audio-codec = <&codec>; |
| audio-routing = |
| "MIC_IN", "Mic Jack", |
| "Mic Jack", "Mic Bias", |
| "Headphone Jack", "HP_OUT"; |
| mux-int-port = <1>; |
| mux-ext-port = <4>; |
| }; |
| }; |
| |
| &audmux { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_audmux>; |
| status = "okay"; |
| }; |
| |
| &ecspi1 { |
| cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1>; |
| status = "okay"; |
| |
| flash: m25p80@0 { |
| compatible = "sst,w25q256", "jedec,spi-nor"; |
| spi-max-frequency = <30000000>; |
| reg = <0>; |
| }; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet>; |
| phy-mode = "rgmii-id"; |
| phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| ddc-i2c-bus = <&i2c3>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| eeprom1: eeprom@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| pagesize = <16>; |
| }; |
| |
| eeprom2: eeprom@51 { |
| compatible = "atmel,24c02"; |
| reg = <0x51>; |
| pagesize = <16>; |
| }; |
| |
| eeprom3: eeprom@52 { |
| compatible = "atmel,24c02"; |
| reg = <0x52>; |
| pagesize = <16>; |
| }; |
| |
| eeprom4: eeprom@53 { |
| compatible = "atmel,24c02"; |
| reg = <0x53>; |
| pagesize = <16>; |
| }; |
| |
| gpio: pca9555@23 { |
| compatible = "nxp,pca9555"; |
| reg = <0x23>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| rtc: ds1672@68 { |
| compatible = "dallas,ds1672"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| pmic: pfuze100@8 { |
| compatible = "fsl,pfuze100"; |
| reg = <0x08>; |
| |
| regulators { |
| sw1a_reg: sw1ab { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw1c_reg: sw1c { |
| regulator-min-microvolt = <300000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3950000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3a_reg: sw3a { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw3b_reg: sw3b { |
| regulator-min-microvolt = <400000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| swbst_reg: swbst { |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5150000>; |
| }; |
| |
| snvs_reg: vsnvs { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vref_reg: vrefddr { |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen2_reg: vgen2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen3_reg: vgen3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vgen4_reg: vgen4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen5_reg: vgen5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen6_reg: vgen6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| accelerometer: mma8450@1c { |
| compatible = "fsl,mma8450"; |
| reg = <0x1c>; |
| }; |
| |
| codec: sgtl5000@a { |
| compatible = "fsl,sgtl5000"; |
| reg = <0x0a>; |
| clocks = <&clks IMX6QDL_CLK_CKO>; |
| VDDA-supply = <&sw4_reg>; |
| VDDIO-supply = <®_3p3v>; |
| }; |
| |
| touchscreen: egalax_ts@4 { |
| compatible = "eeti,egalax_ts"; |
| reg = <0x04>; |
| interrupt-parent = <&gpio7>; |
| interrupts = <12 2>; |
| wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| &ldb { |
| status = "okay"; |
| }; |
| |
| &pcie { |
| reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &ssi1 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart5>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| vbus-supply = <®_usb_otg_vbus>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| disable-over-current; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_h1_vbus>; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <®_3p3v>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_audmux: audmuxgrp { |
| fsl,pins = < |
| MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 |
| MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 |
| MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 |
| MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 |
| MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */ |
| >; |
| }; |
| |
| pinctrl_ecspi1: ecspi1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 |
| MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 |
| MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 |
| MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0 /* SPINOR_CS0# */ |
| >; |
| }; |
| |
| pinctrl_enet: enetgrp { |
| fsl,pins = < |
| MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030 |
| MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030 |
| MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030 |
| MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030 |
| MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 |
| MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 |
| MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030 |
| MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030 |
| MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030 |
| MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030 |
| MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030 |
| MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030 |
| MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 |
| MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 |
| MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 |
| MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 |
| >; |
| }; |
| |
| pinctrl_gpio_leds: gpioledsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* user1 led */ |
| MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 /* user2 led */ |
| MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0 /* user3 led */ |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_pcie: pciegrp { |
| fsl,pins = < |
| MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0 /* PCIE IRQ */ |
| MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PCIE RST */ |
| >; |
| }; |
| |
| pinctrl_pps: ppsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b0 /* GPS_PPS */ |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart5: uart5grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */ |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 |
| MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 |
| MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 |
| MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 |
| MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 |
| MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 |
| >; |
| }; |
| }; |
