| // SPDX-License-Identifier: GPL-2.0 |
| / { |
| mbus@f1000000 { |
| pciec: pcie@82000000 { |
| compatible = "marvell,kirkwood-pcie"; |
| status = "disabled"; |
| device_type = "pci"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| bus-range = <0x00 0xff>; |
| |
| ranges = |
| <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 |
| 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ |
| 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; |
| |
| pcie0: pcie@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; |
| reg = <0x0800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 |
| 0x81000000 0 0 0x81000000 0x1 0 1 0>; |
| bus-range = <0x00 0xff>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &intc 9>; |
| marvell,pcie-port = <0>; |
| marvell,pcie-lane = <0>; |
| clocks = <&gate_clk 2>; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| ocp@f1000000 { |
| pinctrl: pin-controller@10000 { |
| compatible = "marvell,88f6192-pinctrl"; |
| |
| pmx_sata0: pmx-sata0 { |
| marvell,pins = "mpp5", "mpp21", "mpp23"; |
| marvell,function = "sata0"; |
| }; |
| pmx_sata1: pmx-sata1 { |
| marvell,pins = "mpp4", "mpp20", "mpp22"; |
| marvell,function = "sata1"; |
| }; |
| pmx_sdio: pmx-sdio { |
| marvell,pins = "mpp12", "mpp13", "mpp14", |
| "mpp15", "mpp16", "mpp17"; |
| marvell,function = "sdio"; |
| }; |
| }; |
| |
| rtc: rtc@10300 { |
| compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; |
| reg = <0x10300 0x20>; |
| interrupts = <53>; |
| clocks = <&gate_clk 7>; |
| }; |
| |
| sata: sata@80000 { |
| compatible = "marvell,orion-sata"; |
| reg = <0x80000 0x5000>; |
| interrupts = <21>; |
| clocks = <&gate_clk 14>, <&gate_clk 15>; |
| clock-names = "0", "1"; |
| phys = <&sata_phy0>, <&sata_phy1>; |
| phy-names = "port0", "port1"; |
| status = "disabled"; |
| }; |
| |
| sdio: mvsdio@90000 { |
| compatible = "marvell,orion-sdio"; |
| reg = <0x90000 0x200>; |
| interrupts = <28>; |
| clocks = <&gate_clk 4>; |
| bus-width = <4>; |
| cap-sdio-irq; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| status = "disabled"; |
| }; |
| }; |
| }; |
