| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd. |
| * Author: Lin Huang <hl@rock-chips.com> |
| */ |
| |
| #include <linux/arm-smccc.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/devfreq.h> |
| #include <linux/devfreq-event.h> |
| #include <linux/interrupt.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_opp.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/rwsem.h> |
| #include <linux/suspend.h> |
| |
| #include <soc/rockchip/rk3399_grf.h> |
| #include <soc/rockchip/rockchip_sip.h> |
| |
| struct dram_timing { |
| unsigned int ddr3_speed_bin; |
| unsigned int pd_idle; |
| unsigned int sr_idle; |
| unsigned int sr_mc_gate_idle; |
| unsigned int srpd_lite_idle; |
| unsigned int standby_idle; |
| unsigned int auto_pd_dis_freq; |
| unsigned int dram_dll_dis_freq; |
| unsigned int phy_dll_dis_freq; |
| unsigned int ddr3_odt_dis_freq; |
| unsigned int ddr3_drv; |
| unsigned int ddr3_odt; |
| unsigned int phy_ddr3_ca_drv; |
| unsigned int phy_ddr3_dq_drv; |
| unsigned int phy_ddr3_odt; |
| unsigned int lpddr3_odt_dis_freq; |
| unsigned int lpddr3_drv; |
| unsigned int lpddr3_odt; |
| unsigned int phy_lpddr3_ca_drv; |
| unsigned int phy_lpddr3_dq_drv; |
| unsigned int phy_lpddr3_odt; |
| unsigned int lpddr4_odt_dis_freq; |
| unsigned int lpddr4_drv; |
| unsigned int lpddr4_dq_odt; |
| unsigned int lpddr4_ca_odt; |
| unsigned int phy_lpddr4_ca_drv; |
| unsigned int phy_lpddr4_ck_cs_drv; |
| unsigned int phy_lpddr4_dq_drv; |
| unsigned int phy_lpddr4_odt; |
| }; |
| |
| struct rk3399_dmcfreq { |
| struct device *dev; |
| struct devfreq *devfreq; |
| struct devfreq_simple_ondemand_data ondemand_data; |
| struct clk *dmc_clk; |
| struct devfreq_event_dev *edev; |
| struct mutex lock; |
| struct dram_timing timing; |
| struct regulator *vdd_center; |
| struct regmap *regmap_pmu; |
| unsigned long rate, target_rate; |
| unsigned long volt, target_volt; |
| unsigned int odt_dis_freq; |
| int odt_pd_arg0, odt_pd_arg1; |
| }; |
| |
| static int rk3399_dmcfreq_target(struct device *dev, unsigned long *freq, |
| u32 flags) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(dev); |
| struct dev_pm_opp *opp; |
| unsigned long old_clk_rate = dmcfreq->rate; |
| unsigned long target_volt, target_rate; |
| struct arm_smccc_res res; |
| bool odt_enable = false; |
| int err; |
| |
| opp = devfreq_recommended_opp(dev, freq, flags); |
| if (IS_ERR(opp)) |
| return PTR_ERR(opp); |
| |
| target_rate = dev_pm_opp_get_freq(opp); |
| target_volt = dev_pm_opp_get_voltage(opp); |
| dev_pm_opp_put(opp); |
| |
| if (dmcfreq->rate == target_rate) |
| return 0; |
| |
| mutex_lock(&dmcfreq->lock); |
| |
| if (dmcfreq->regmap_pmu) { |
| if (target_rate >= dmcfreq->odt_dis_freq) |
| odt_enable = true; |
| |
| /* |
| * This makes a SMC call to the TF-A to set the DDR PD |
| * (power-down) timings and to enable or disable the |
| * ODT (on-die termination) resistors. |
| */ |
| arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, dmcfreq->odt_pd_arg0, |
| dmcfreq->odt_pd_arg1, |
| ROCKCHIP_SIP_CONFIG_DRAM_SET_ODT_PD, |
| odt_enable, 0, 0, 0, &res); |
| } |
| |
| /* |
| * If frequency scaling from low to high, adjust voltage first. |
| * If frequency scaling from high to low, adjust frequency first. |
| */ |
| if (old_clk_rate < target_rate) { |
| err = regulator_set_voltage(dmcfreq->vdd_center, target_volt, |
| target_volt); |
| if (err) { |
| dev_err(dev, "Cannot set voltage %lu uV\n", |
| target_volt); |
| goto out; |
| } |
| } |
| |
| err = clk_set_rate(dmcfreq->dmc_clk, target_rate); |
| if (err) { |
| dev_err(dev, "Cannot set frequency %lu (%d)\n", target_rate, |
| err); |
| regulator_set_voltage(dmcfreq->vdd_center, dmcfreq->volt, |
| dmcfreq->volt); |
| goto out; |
| } |
| |
| /* |
| * Check the dpll rate, |
| * There only two result we will get, |
| * 1. Ddr frequency scaling fail, we still get the old rate. |
| * 2. Ddr frequency scaling sucessful, we get the rate we set. |
| */ |
| dmcfreq->rate = clk_get_rate(dmcfreq->dmc_clk); |
| |
| /* If get the incorrect rate, set voltage to old value. */ |
| if (dmcfreq->rate != target_rate) { |
| dev_err(dev, "Got wrong frequency, Request %lu, Current %lu\n", |
| target_rate, dmcfreq->rate); |
| regulator_set_voltage(dmcfreq->vdd_center, dmcfreq->volt, |
| dmcfreq->volt); |
| goto out; |
| } else if (old_clk_rate > target_rate) |
| err = regulator_set_voltage(dmcfreq->vdd_center, target_volt, |
| target_volt); |
| if (err) |
| dev_err(dev, "Cannot set voltage %lu uV\n", target_volt); |
| |
| dmcfreq->rate = target_rate; |
| dmcfreq->volt = target_volt; |
| |
| out: |
| mutex_unlock(&dmcfreq->lock); |
| return err; |
| } |
| |
| static int rk3399_dmcfreq_get_dev_status(struct device *dev, |
| struct devfreq_dev_status *stat) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(dev); |
| struct devfreq_event_data edata; |
| int ret = 0; |
| |
| ret = devfreq_event_get_event(dmcfreq->edev, &edata); |
| if (ret < 0) |
| return ret; |
| |
| stat->current_frequency = dmcfreq->rate; |
| stat->busy_time = edata.load_count; |
| stat->total_time = edata.total_count; |
| |
| return ret; |
| } |
| |
| static int rk3399_dmcfreq_get_cur_freq(struct device *dev, unsigned long *freq) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(dev); |
| |
| *freq = dmcfreq->rate; |
| |
| return 0; |
| } |
| |
| static struct devfreq_dev_profile rk3399_devfreq_dmc_profile = { |
| .polling_ms = 200, |
| .target = rk3399_dmcfreq_target, |
| .get_dev_status = rk3399_dmcfreq_get_dev_status, |
| .get_cur_freq = rk3399_dmcfreq_get_cur_freq, |
| }; |
| |
| static __maybe_unused int rk3399_dmcfreq_suspend(struct device *dev) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(dev); |
| int ret = 0; |
| |
| ret = devfreq_event_disable_edev(dmcfreq->edev); |
| if (ret < 0) { |
| dev_err(dev, "failed to disable the devfreq-event devices\n"); |
| return ret; |
| } |
| |
| ret = devfreq_suspend_device(dmcfreq->devfreq); |
| if (ret < 0) { |
| dev_err(dev, "failed to suspend the devfreq devices\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static __maybe_unused int rk3399_dmcfreq_resume(struct device *dev) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(dev); |
| int ret = 0; |
| |
| ret = devfreq_event_enable_edev(dmcfreq->edev); |
| if (ret < 0) { |
| dev_err(dev, "failed to enable the devfreq-event devices\n"); |
| return ret; |
| } |
| |
| ret = devfreq_resume_device(dmcfreq->devfreq); |
| if (ret < 0) { |
| dev_err(dev, "failed to resume the devfreq devices\n"); |
| return ret; |
| } |
| return ret; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(rk3399_dmcfreq_pm, rk3399_dmcfreq_suspend, |
| rk3399_dmcfreq_resume); |
| |
| static int of_get_ddr_timings(struct dram_timing *timing, |
| struct device_node *np) |
| { |
| int ret = 0; |
| |
| ret = of_property_read_u32(np, "rockchip,ddr3_speed_bin", |
| &timing->ddr3_speed_bin); |
| ret |= of_property_read_u32(np, "rockchip,pd_idle", |
| &timing->pd_idle); |
| ret |= of_property_read_u32(np, "rockchip,sr_idle", |
| &timing->sr_idle); |
| ret |= of_property_read_u32(np, "rockchip,sr_mc_gate_idle", |
| &timing->sr_mc_gate_idle); |
| ret |= of_property_read_u32(np, "rockchip,srpd_lite_idle", |
| &timing->srpd_lite_idle); |
| ret |= of_property_read_u32(np, "rockchip,standby_idle", |
| &timing->standby_idle); |
| ret |= of_property_read_u32(np, "rockchip,auto_pd_dis_freq", |
| &timing->auto_pd_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,dram_dll_dis_freq", |
| &timing->dram_dll_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,phy_dll_dis_freq", |
| &timing->phy_dll_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,ddr3_odt_dis_freq", |
| &timing->ddr3_odt_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,ddr3_drv", |
| &timing->ddr3_drv); |
| ret |= of_property_read_u32(np, "rockchip,ddr3_odt", |
| &timing->ddr3_odt); |
| ret |= of_property_read_u32(np, "rockchip,phy_ddr3_ca_drv", |
| &timing->phy_ddr3_ca_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_ddr3_dq_drv", |
| &timing->phy_ddr3_dq_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_ddr3_odt", |
| &timing->phy_ddr3_odt); |
| ret |= of_property_read_u32(np, "rockchip,lpddr3_odt_dis_freq", |
| &timing->lpddr3_odt_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,lpddr3_drv", |
| &timing->lpddr3_drv); |
| ret |= of_property_read_u32(np, "rockchip,lpddr3_odt", |
| &timing->lpddr3_odt); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr3_ca_drv", |
| &timing->phy_lpddr3_ca_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr3_dq_drv", |
| &timing->phy_lpddr3_dq_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr3_odt", |
| &timing->phy_lpddr3_odt); |
| ret |= of_property_read_u32(np, "rockchip,lpddr4_odt_dis_freq", |
| &timing->lpddr4_odt_dis_freq); |
| ret |= of_property_read_u32(np, "rockchip,lpddr4_drv", |
| &timing->lpddr4_drv); |
| ret |= of_property_read_u32(np, "rockchip,lpddr4_dq_odt", |
| &timing->lpddr4_dq_odt); |
| ret |= of_property_read_u32(np, "rockchip,lpddr4_ca_odt", |
| &timing->lpddr4_ca_odt); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr4_ca_drv", |
| &timing->phy_lpddr4_ca_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr4_ck_cs_drv", |
| &timing->phy_lpddr4_ck_cs_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr4_dq_drv", |
| &timing->phy_lpddr4_dq_drv); |
| ret |= of_property_read_u32(np, "rockchip,phy_lpddr4_odt", |
| &timing->phy_lpddr4_odt); |
| |
| return ret; |
| } |
| |
| static int rk3399_dmcfreq_probe(struct platform_device *pdev) |
| { |
| struct arm_smccc_res res; |
| struct device *dev = &pdev->dev; |
| struct device_node *np = pdev->dev.of_node, *node; |
| struct rk3399_dmcfreq *data; |
| int ret, index, size; |
| uint32_t *timing; |
| struct dev_pm_opp *opp; |
| u32 ddr_type; |
| u32 val; |
| |
| data = devm_kzalloc(dev, sizeof(struct rk3399_dmcfreq), GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| |
| mutex_init(&data->lock); |
| |
| data->vdd_center = devm_regulator_get(dev, "center"); |
| if (IS_ERR(data->vdd_center)) |
| return dev_err_probe(dev, PTR_ERR(data->vdd_center), |
| "Cannot get the regulator \"center\"\n"); |
| |
| data->dmc_clk = devm_clk_get(dev, "dmc_clk"); |
| if (IS_ERR(data->dmc_clk)) |
| return dev_err_probe(dev, PTR_ERR(data->dmc_clk), |
| "Cannot get the clk dmc_clk\n"); |
| |
| data->edev = devfreq_event_get_edev_by_phandle(dev, "devfreq-events", 0); |
| if (IS_ERR(data->edev)) |
| return -EPROBE_DEFER; |
| |
| ret = devfreq_event_enable_edev(data->edev); |
| if (ret < 0) { |
| dev_err(dev, "failed to enable devfreq-event devices\n"); |
| return ret; |
| } |
| |
| /* |
| * Get dram timing and pass it to arm trust firmware, |
| * the dram driver in arm trust firmware will get these |
| * timing and to do dram initial. |
| */ |
| if (!of_get_ddr_timings(&data->timing, np)) { |
| timing = &data->timing.ddr3_speed_bin; |
| size = sizeof(struct dram_timing) / 4; |
| for (index = 0; index < size; index++) { |
| arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, *timing++, index, |
| ROCKCHIP_SIP_CONFIG_DRAM_SET_PARAM, |
| 0, 0, 0, 0, &res); |
| if (res.a0) { |
| dev_err(dev, "Failed to set dram param: %ld\n", |
| res.a0); |
| ret = -EINVAL; |
| goto err_edev; |
| } |
| } |
| } |
| |
| node = of_parse_phandle(np, "rockchip,pmu", 0); |
| if (!node) |
| goto no_pmu; |
| |
| data->regmap_pmu = syscon_node_to_regmap(node); |
| of_node_put(node); |
| if (IS_ERR(data->regmap_pmu)) { |
| ret = PTR_ERR(data->regmap_pmu); |
| goto err_edev; |
| } |
| |
| regmap_read(data->regmap_pmu, RK3399_PMUGRF_OS_REG2, &val); |
| ddr_type = (val >> RK3399_PMUGRF_DDRTYPE_SHIFT) & |
| RK3399_PMUGRF_DDRTYPE_MASK; |
| |
| switch (ddr_type) { |
| case RK3399_PMUGRF_DDRTYPE_DDR3: |
| data->odt_dis_freq = data->timing.ddr3_odt_dis_freq; |
| break; |
| case RK3399_PMUGRF_DDRTYPE_LPDDR3: |
| data->odt_dis_freq = data->timing.lpddr3_odt_dis_freq; |
| break; |
| case RK3399_PMUGRF_DDRTYPE_LPDDR4: |
| data->odt_dis_freq = data->timing.lpddr4_odt_dis_freq; |
| break; |
| default: |
| ret = -EINVAL; |
| goto err_edev; |
| } |
| |
| no_pmu: |
| arm_smccc_smc(ROCKCHIP_SIP_DRAM_FREQ, 0, 0, |
| ROCKCHIP_SIP_CONFIG_DRAM_INIT, |
| 0, 0, 0, 0, &res); |
| |
| /* |
| * In TF-A there is a platform SIP call to set the PD (power-down) |
| * timings and to enable or disable the ODT (on-die termination). |
| * This call needs three arguments as follows: |
| * |
| * arg0: |
| * bit[0-7] : sr_idle |
| * bit[8-15] : sr_mc_gate_idle |
| * bit[16-31] : standby idle |
| * arg1: |
| * bit[0-11] : pd_idle |
| * bit[16-27] : srpd_lite_idle |
| * arg2: |
| * bit[0] : odt enable |
| */ |
| data->odt_pd_arg0 = (data->timing.sr_idle & 0xff) | |
| ((data->timing.sr_mc_gate_idle & 0xff) << 8) | |
| ((data->timing.standby_idle & 0xffff) << 16); |
| data->odt_pd_arg1 = (data->timing.pd_idle & 0xfff) | |
| ((data->timing.srpd_lite_idle & 0xfff) << 16); |
| |
| /* |
| * We add a devfreq driver to our parent since it has a device tree node |
| * with operating points. |
| */ |
| if (dev_pm_opp_of_add_table(dev)) { |
| dev_err(dev, "Invalid operating-points in device tree.\n"); |
| ret = -EINVAL; |
| goto err_edev; |
| } |
| |
| of_property_read_u32(np, "upthreshold", |
| &data->ondemand_data.upthreshold); |
| of_property_read_u32(np, "downdifferential", |
| &data->ondemand_data.downdifferential); |
| |
| data->rate = clk_get_rate(data->dmc_clk); |
| |
| opp = devfreq_recommended_opp(dev, &data->rate, 0); |
| if (IS_ERR(opp)) { |
| ret = PTR_ERR(opp); |
| goto err_free_opp; |
| } |
| |
| data->rate = dev_pm_opp_get_freq(opp); |
| data->volt = dev_pm_opp_get_voltage(opp); |
| dev_pm_opp_put(opp); |
| |
| rk3399_devfreq_dmc_profile.initial_freq = data->rate; |
| |
| data->devfreq = devm_devfreq_add_device(dev, |
| &rk3399_devfreq_dmc_profile, |
| DEVFREQ_GOV_SIMPLE_ONDEMAND, |
| &data->ondemand_data); |
| if (IS_ERR(data->devfreq)) { |
| ret = PTR_ERR(data->devfreq); |
| goto err_free_opp; |
| } |
| |
| devm_devfreq_register_opp_notifier(dev, data->devfreq); |
| |
| data->dev = dev; |
| platform_set_drvdata(pdev, data); |
| |
| return 0; |
| |
| err_free_opp: |
| dev_pm_opp_of_remove_table(&pdev->dev); |
| err_edev: |
| devfreq_event_disable_edev(data->edev); |
| |
| return ret; |
| } |
| |
| static int rk3399_dmcfreq_remove(struct platform_device *pdev) |
| { |
| struct rk3399_dmcfreq *dmcfreq = dev_get_drvdata(&pdev->dev); |
| |
| /* |
| * Before remove the opp table we need to unregister the opp notifier. |
| */ |
| devm_devfreq_unregister_opp_notifier(dmcfreq->dev, dmcfreq->devfreq); |
| dev_pm_opp_of_remove_table(dmcfreq->dev); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id rk3399dmc_devfreq_of_match[] = { |
| { .compatible = "rockchip,rk3399-dmc" }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, rk3399dmc_devfreq_of_match); |
| |
| static struct platform_driver rk3399_dmcfreq_driver = { |
| .probe = rk3399_dmcfreq_probe, |
| .remove = rk3399_dmcfreq_remove, |
| .driver = { |
| .name = "rk3399-dmc-freq", |
| .pm = &rk3399_dmcfreq_pm, |
| .of_match_table = rk3399dmc_devfreq_of_match, |
| }, |
| }; |
| module_platform_driver(rk3399_dmcfreq_driver); |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_AUTHOR("Lin Huang <hl@rock-chips.com>"); |
| MODULE_DESCRIPTION("RK3399 dmcfreq driver with devfreq framework"); |