| /* |
| * Toppoly TD028TTEC1 panel support |
| * |
| * Copyright (C) 2008 Nokia Corporation |
| * Author: Tomi Valkeinen <tomi.valkeinen@nokia.com> |
| * |
| * Neo 1973 code (jbt6k74.c): |
| * Copyright (C) 2006-2007 by OpenMoko, Inc. |
| * Author: Harald Welte <laforge@openmoko.org> |
| * |
| * Ported and adapted from Neo 1973 U-Boot by: |
| * H. Nikolaus Schaller <hns@goldelico.com> |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License version 2 as published by |
| * the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along with |
| * this program. If not, see <http://www.gnu.org/licenses/>. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/delay.h> |
| #include <linux/spi/spi.h> |
| #include <linux/gpio.h> |
| #include <video/omapdss.h> |
| #include <video/omap-panel-data.h> |
| |
| struct panel_drv_data { |
| struct omap_dss_device dssdev; |
| struct omap_dss_device *in; |
| |
| int data_lines; |
| |
| struct omap_video_timings videomode; |
| |
| struct spi_device *spi_dev; |
| }; |
| |
| static struct omap_video_timings td028ttec1_panel_timings = { |
| .x_res = 480, |
| .y_res = 640, |
| .pixelclock = 22153000, |
| .hfp = 24, |
| .hsw = 8, |
| .hbp = 8, |
| .vfp = 4, |
| .vsw = 2, |
| .vbp = 2, |
| |
| .vsync_level = OMAPDSS_SIG_ACTIVE_LOW, |
| .hsync_level = OMAPDSS_SIG_ACTIVE_LOW, |
| |
| .data_pclk_edge = OMAPDSS_DRIVE_SIG_FALLING_EDGE, |
| .de_level = OMAPDSS_SIG_ACTIVE_HIGH, |
| .sync_pclk_edge = OMAPDSS_DRIVE_SIG_RISING_EDGE, |
| }; |
| |
| #define JBT_COMMAND 0x000 |
| #define JBT_DATA 0x100 |
| |
| static int jbt_ret_write_0(struct panel_drv_data *ddata, u8 reg) |
| { |
| int rc; |
| u16 tx_buf = JBT_COMMAND | reg; |
| |
| rc = spi_write(ddata->spi_dev, (u8 *)&tx_buf, |
| 1*sizeof(u16)); |
| if (rc != 0) |
| dev_err(&ddata->spi_dev->dev, |
| "jbt_ret_write_0 spi_write ret %d\n", rc); |
| |
| return rc; |
| } |
| |
| static int jbt_reg_write_1(struct panel_drv_data *ddata, u8 reg, u8 data) |
| { |
| int rc; |
| u16 tx_buf[2]; |
| |
| tx_buf[0] = JBT_COMMAND | reg; |
| tx_buf[1] = JBT_DATA | data; |
| rc = spi_write(ddata->spi_dev, (u8 *)tx_buf, |
| 2*sizeof(u16)); |
| if (rc != 0) |
| dev_err(&ddata->spi_dev->dev, |
| "jbt_reg_write_1 spi_write ret %d\n", rc); |
| |
| return rc; |
| } |
| |
| static int jbt_reg_write_2(struct panel_drv_data *ddata, u8 reg, u16 data) |
| { |
| int rc; |
| u16 tx_buf[3]; |
| |
| tx_buf[0] = JBT_COMMAND | reg; |
| tx_buf[1] = JBT_DATA | (data >> 8); |
| tx_buf[2] = JBT_DATA | (data & 0xff); |
| |
| rc = spi_write(ddata->spi_dev, (u8 *)tx_buf, |
| 3*sizeof(u16)); |
| |
| if (rc != 0) |
| dev_err(&ddata->spi_dev->dev, |
| "jbt_reg_write_2 spi_write ret %d\n", rc); |
| |
| return rc; |
| } |
| |
| enum jbt_register { |
| JBT_REG_SLEEP_IN = 0x10, |
| JBT_REG_SLEEP_OUT = 0x11, |
| |
| JBT_REG_DISPLAY_OFF = 0x28, |
| JBT_REG_DISPLAY_ON = 0x29, |
| |
| JBT_REG_RGB_FORMAT = 0x3a, |
| JBT_REG_QUAD_RATE = 0x3b, |
| |
| JBT_REG_POWER_ON_OFF = 0xb0, |
| JBT_REG_BOOSTER_OP = 0xb1, |
| JBT_REG_BOOSTER_MODE = 0xb2, |
| JBT_REG_BOOSTER_FREQ = 0xb3, |
| JBT_REG_OPAMP_SYSCLK = 0xb4, |
| JBT_REG_VSC_VOLTAGE = 0xb5, |
| JBT_REG_VCOM_VOLTAGE = 0xb6, |
| JBT_REG_EXT_DISPL = 0xb7, |
| JBT_REG_OUTPUT_CONTROL = 0xb8, |
| JBT_REG_DCCLK_DCEV = 0xb9, |
| JBT_REG_DISPLAY_MODE1 = 0xba, |
| JBT_REG_DISPLAY_MODE2 = 0xbb, |
| JBT_REG_DISPLAY_MODE = 0xbc, |
| JBT_REG_ASW_SLEW = 0xbd, |
| JBT_REG_DUMMY_DISPLAY = 0xbe, |
| JBT_REG_DRIVE_SYSTEM = 0xbf, |
| |
| JBT_REG_SLEEP_OUT_FR_A = 0xc0, |
| JBT_REG_SLEEP_OUT_FR_B = 0xc1, |
| JBT_REG_SLEEP_OUT_FR_C = 0xc2, |
| JBT_REG_SLEEP_IN_LCCNT_D = 0xc3, |
| JBT_REG_SLEEP_IN_LCCNT_E = 0xc4, |
| JBT_REG_SLEEP_IN_LCCNT_F = 0xc5, |
| JBT_REG_SLEEP_IN_LCCNT_G = 0xc6, |
| |
| JBT_REG_GAMMA1_FINE_1 = 0xc7, |
| JBT_REG_GAMMA1_FINE_2 = 0xc8, |
| JBT_REG_GAMMA1_INCLINATION = 0xc9, |
| JBT_REG_GAMMA1_BLUE_OFFSET = 0xca, |
| |
| JBT_REG_BLANK_CONTROL = 0xcf, |
| JBT_REG_BLANK_TH_TV = 0xd0, |
| JBT_REG_CKV_ON_OFF = 0xd1, |
| JBT_REG_CKV_1_2 = 0xd2, |
| JBT_REG_OEV_TIMING = 0xd3, |
| JBT_REG_ASW_TIMING_1 = 0xd4, |
| JBT_REG_ASW_TIMING_2 = 0xd5, |
| |
| JBT_REG_HCLOCK_VGA = 0xec, |
| JBT_REG_HCLOCK_QVGA = 0xed, |
| }; |
| |
| #define to_panel_data(p) container_of(p, struct panel_drv_data, dssdev) |
| |
| static int td028ttec1_panel_connect(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| int r; |
| |
| if (omapdss_device_is_connected(dssdev)) |
| return 0; |
| |
| r = in->ops.dpi->connect(in, dssdev); |
| if (r) |
| return r; |
| |
| return 0; |
| } |
| |
| static void td028ttec1_panel_disconnect(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| if (!omapdss_device_is_connected(dssdev)) |
| return; |
| |
| in->ops.dpi->disconnect(in, dssdev); |
| } |
| |
| static int td028ttec1_panel_enable(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| int r; |
| |
| if (!omapdss_device_is_connected(dssdev)) |
| return -ENODEV; |
| |
| if (omapdss_device_is_enabled(dssdev)) |
| return 0; |
| |
| if (ddata->data_lines) |
| in->ops.dpi->set_data_lines(in, ddata->data_lines); |
| in->ops.dpi->set_timings(in, &ddata->videomode); |
| |
| r = in->ops.dpi->enable(in); |
| if (r) |
| return r; |
| |
| dev_dbg(dssdev->dev, "td028ttec1_panel_enable() - state %d\n", |
| dssdev->state); |
| |
| /* three times command zero */ |
| r |= jbt_ret_write_0(ddata, 0x00); |
| usleep_range(1000, 2000); |
| r |= jbt_ret_write_0(ddata, 0x00); |
| usleep_range(1000, 2000); |
| r |= jbt_ret_write_0(ddata, 0x00); |
| usleep_range(1000, 2000); |
| |
| if (r) { |
| dev_warn(dssdev->dev, "transfer error\n"); |
| goto transfer_err; |
| } |
| |
| /* deep standby out */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x17); |
| |
| /* RGB I/F on, RAM write off, QVGA through, SIGCON enable */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE, 0x80); |
| |
| /* Quad mode off */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_QUAD_RATE, 0x00); |
| |
| /* AVDD on, XVDD on */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x16); |
| |
| /* Output control */ |
| r |= jbt_reg_write_2(ddata, JBT_REG_OUTPUT_CONTROL, 0xfff9); |
| |
| /* Sleep mode off */ |
| r |= jbt_ret_write_0(ddata, JBT_REG_SLEEP_OUT); |
| |
| /* at this point we have like 50% grey */ |
| |
| /* initialize register set */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE1, 0x01); |
| r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE2, 0x00); |
| r |= jbt_reg_write_1(ddata, JBT_REG_RGB_FORMAT, 0x60); |
| r |= jbt_reg_write_1(ddata, JBT_REG_DRIVE_SYSTEM, 0x10); |
| r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_OP, 0x56); |
| r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_MODE, 0x33); |
| r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_FREQ, 0x11); |
| r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_FREQ, 0x11); |
| r |= jbt_reg_write_1(ddata, JBT_REG_OPAMP_SYSCLK, 0x02); |
| r |= jbt_reg_write_1(ddata, JBT_REG_VSC_VOLTAGE, 0x2b); |
| r |= jbt_reg_write_1(ddata, JBT_REG_VCOM_VOLTAGE, 0x40); |
| r |= jbt_reg_write_1(ddata, JBT_REG_EXT_DISPL, 0x03); |
| r |= jbt_reg_write_1(ddata, JBT_REG_DCCLK_DCEV, 0x04); |
| /* |
| * default of 0x02 in JBT_REG_ASW_SLEW responsible for 72Hz requirement |
| * to avoid red / blue flicker |
| */ |
| r |= jbt_reg_write_1(ddata, JBT_REG_ASW_SLEW, 0x04); |
| r |= jbt_reg_write_1(ddata, JBT_REG_DUMMY_DISPLAY, 0x00); |
| |
| r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_A, 0x11); |
| r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_B, 0x11); |
| r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_C, 0x11); |
| r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_D, 0x2040); |
| r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_E, 0x60c0); |
| r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_F, 0x1020); |
| r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_G, 0x60c0); |
| |
| r |= jbt_reg_write_2(ddata, JBT_REG_GAMMA1_FINE_1, 0x5533); |
| r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_FINE_2, 0x00); |
| r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_INCLINATION, 0x00); |
| r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_BLUE_OFFSET, 0x00); |
| |
| r |= jbt_reg_write_2(ddata, JBT_REG_HCLOCK_VGA, 0x1f0); |
| r |= jbt_reg_write_1(ddata, JBT_REG_BLANK_CONTROL, 0x02); |
| r |= jbt_reg_write_2(ddata, JBT_REG_BLANK_TH_TV, 0x0804); |
| |
| r |= jbt_reg_write_1(ddata, JBT_REG_CKV_ON_OFF, 0x01); |
| r |= jbt_reg_write_2(ddata, JBT_REG_CKV_1_2, 0x0000); |
| |
| r |= jbt_reg_write_2(ddata, JBT_REG_OEV_TIMING, 0x0d0e); |
| r |= jbt_reg_write_2(ddata, JBT_REG_ASW_TIMING_1, 0x11a4); |
| r |= jbt_reg_write_1(ddata, JBT_REG_ASW_TIMING_2, 0x0e); |
| |
| r |= jbt_ret_write_0(ddata, JBT_REG_DISPLAY_ON); |
| |
| dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; |
| |
| transfer_err: |
| |
| return r ? -EIO : 0; |
| } |
| |
| static void td028ttec1_panel_disable(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| if (!omapdss_device_is_enabled(dssdev)) |
| return; |
| |
| dev_dbg(dssdev->dev, "td028ttec1_panel_disable()\n"); |
| |
| jbt_ret_write_0(ddata, JBT_REG_DISPLAY_OFF); |
| jbt_reg_write_2(ddata, JBT_REG_OUTPUT_CONTROL, 0x8002); |
| jbt_ret_write_0(ddata, JBT_REG_SLEEP_IN); |
| jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x00); |
| |
| in->ops.dpi->disable(in); |
| |
| dssdev->state = OMAP_DSS_DISPLAY_DISABLED; |
| } |
| |
| static void td028ttec1_panel_set_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| ddata->videomode = *timings; |
| dssdev->panel.timings = *timings; |
| |
| in->ops.dpi->set_timings(in, timings); |
| } |
| |
| static void td028ttec1_panel_get_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| |
| *timings = ddata->videomode; |
| } |
| |
| static int td028ttec1_panel_check_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| return in->ops.dpi->check_timings(in, timings); |
| } |
| |
| static struct omap_dss_driver td028ttec1_ops = { |
| .connect = td028ttec1_panel_connect, |
| .disconnect = td028ttec1_panel_disconnect, |
| |
| .enable = td028ttec1_panel_enable, |
| .disable = td028ttec1_panel_disable, |
| |
| .set_timings = td028ttec1_panel_set_timings, |
| .get_timings = td028ttec1_panel_get_timings, |
| .check_timings = td028ttec1_panel_check_timings, |
| }; |
| |
| static int td028ttec1_panel_probe_pdata(struct spi_device *spi) |
| { |
| const struct panel_tpo_td028ttec1_platform_data *pdata; |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *dssdev, *in; |
| |
| pdata = dev_get_platdata(&spi->dev); |
| |
| in = omap_dss_find_output(pdata->source); |
| if (in == NULL) { |
| dev_err(&spi->dev, "failed to find video source '%s'\n", |
| pdata->source); |
| return -EPROBE_DEFER; |
| } |
| |
| ddata->in = in; |
| |
| ddata->data_lines = pdata->data_lines; |
| |
| dssdev = &ddata->dssdev; |
| dssdev->name = pdata->name; |
| |
| return 0; |
| } |
| |
| static int td028ttec1_probe_of(struct spi_device *spi) |
| { |
| struct device_node *node = spi->dev.of_node; |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *in; |
| |
| in = omapdss_of_find_source_for_first_ep(node); |
| if (IS_ERR(in)) { |
| dev_err(&spi->dev, "failed to find video source\n"); |
| return PTR_ERR(in); |
| } |
| |
| ddata->in = in; |
| |
| return 0; |
| } |
| |
| static int td028ttec1_panel_probe(struct spi_device *spi) |
| { |
| struct panel_drv_data *ddata; |
| struct omap_dss_device *dssdev; |
| int r; |
| |
| dev_dbg(&spi->dev, "%s\n", __func__); |
| |
| spi->bits_per_word = 9; |
| spi->mode = SPI_MODE_3; |
| |
| r = spi_setup(spi); |
| if (r < 0) { |
| dev_err(&spi->dev, "spi_setup failed: %d\n", r); |
| return r; |
| } |
| |
| ddata = devm_kzalloc(&spi->dev, sizeof(*ddata), GFP_KERNEL); |
| if (ddata == NULL) |
| return -ENOMEM; |
| |
| dev_set_drvdata(&spi->dev, ddata); |
| |
| ddata->spi_dev = spi; |
| |
| if (dev_get_platdata(&spi->dev)) { |
| r = td028ttec1_panel_probe_pdata(spi); |
| if (r) |
| return r; |
| } else if (spi->dev.of_node) { |
| r = td028ttec1_probe_of(spi); |
| if (r) |
| return r; |
| } else { |
| return -ENODEV; |
| } |
| |
| ddata->videomode = td028ttec1_panel_timings; |
| |
| dssdev = &ddata->dssdev; |
| dssdev->dev = &spi->dev; |
| dssdev->driver = &td028ttec1_ops; |
| dssdev->type = OMAP_DISPLAY_TYPE_DPI; |
| dssdev->owner = THIS_MODULE; |
| dssdev->panel.timings = ddata->videomode; |
| dssdev->phy.dpi.data_lines = ddata->data_lines; |
| |
| r = omapdss_register_display(dssdev); |
| if (r) { |
| dev_err(&spi->dev, "Failed to register panel\n"); |
| goto err_reg; |
| } |
| |
| return 0; |
| |
| err_reg: |
| omap_dss_put_device(ddata->in); |
| return r; |
| } |
| |
| static int td028ttec1_panel_remove(struct spi_device *spi) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *dssdev = &ddata->dssdev; |
| struct omap_dss_device *in = ddata->in; |
| |
| dev_dbg(&ddata->spi_dev->dev, "%s\n", __func__); |
| |
| omapdss_unregister_display(dssdev); |
| |
| td028ttec1_panel_disable(dssdev); |
| td028ttec1_panel_disconnect(dssdev); |
| |
| omap_dss_put_device(in); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id td028ttec1_of_match[] = { |
| { .compatible = "omapdss,toppoly,td028ttec1", }, |
| {}, |
| }; |
| |
| MODULE_DEVICE_TABLE(of, td028ttec1_of_match); |
| |
| static struct spi_driver td028ttec1_spi_driver = { |
| .probe = td028ttec1_panel_probe, |
| .remove = td028ttec1_panel_remove, |
| |
| .driver = { |
| .name = "panel-tpo-td028ttec1", |
| .of_match_table = td028ttec1_of_match, |
| .suppress_bind_attrs = true, |
| }, |
| }; |
| |
| module_spi_driver(td028ttec1_spi_driver); |
| |
| MODULE_ALIAS("spi:toppoly,td028ttec1"); |
| MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>"); |
| MODULE_DESCRIPTION("Toppoly TD028TTEC1 panel driver"); |
| MODULE_LICENSE("GPL"); |