| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * isp.c |
| * |
| * TI OMAP3 ISP - Core |
| * |
| * Copyright (C) 2006-2010 Nokia Corporation |
| * Copyright (C) 2007-2009 Texas Instruments, Inc. |
| * |
| * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com> |
| * Sakari Ailus <sakari.ailus@iki.fi> |
| * |
| * Contributors: |
| * Laurent Pinchart <laurent.pinchart@ideasonboard.com> |
| * Sakari Ailus <sakari.ailus@iki.fi> |
| * David Cohen <dacohen@gmail.com> |
| * Stanimir Varbanov <svarbanov@mm-sol.com> |
| * Vimarsh Zutshi <vimarsh.zutshi@gmail.com> |
| * Tuukka Toivonen <tuukkat76@gmail.com> |
| * Sergio Aguirre <saaguirre@ti.com> |
| * Antti Koskipaa <akoskipa@gmail.com> |
| * Ivan T. Ivanov <iivanov@mm-sol.com> |
| * RaniSuneela <r-m@ti.com> |
| * Atanas Filipov <afilipov@mm-sol.com> |
| * Gjorgji Rosikopulos <grosikopulos@mm-sol.com> |
| * Hiroshi DOYU <hiroshi.doyu@nokia.com> |
| * Nayden Kanchev <nkanchev@mm-sol.com> |
| * Phil Carmody <ext-phil.2.carmody@nokia.com> |
| * Artem Bityutskiy <artem.bityutskiy@nokia.com> |
| * Dominic Curran <dcurran@ti.com> |
| * Ilkka Myllyperkio <ilkka.myllyperkio@sofica.fi> |
| * Pallavi Kulkarni <p-kulkarni@ti.com> |
| * Vaibhav Hiremath <hvaibhav@ti.com> |
| * Mohit Jalori <mjalori@ti.com> |
| * Sameer Venkatraman <sameerv@ti.com> |
| * Senthilvadivu Guruswamy <svadivu@ti.com> |
| * Thara Gopinath <thara@ti.com> |
| * Toni Leinonen <toni.leinonen@nokia.com> |
| * Troy Laramy <t-laramy@ti.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/clkdev.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/omap-iommu.h> |
| #include <linux/platform_device.h> |
| #include <linux/property.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/slab.h> |
| #include <linux/sched.h> |
| #include <linux/vmalloc.h> |
| |
| #ifdef CONFIG_ARM_DMA_USE_IOMMU |
| #include <asm/dma-iommu.h> |
| #endif |
| |
| #include <media/v4l2-common.h> |
| #include <media/v4l2-fwnode.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-mc.h> |
| |
| #include "isp.h" |
| #include "ispreg.h" |
| #include "ispccdc.h" |
| #include "isppreview.h" |
| #include "ispresizer.h" |
| #include "ispcsi2.h" |
| #include "ispccp2.h" |
| #include "isph3a.h" |
| #include "isphist.h" |
| |
| static unsigned int autoidle; |
| module_param(autoidle, int, 0444); |
| MODULE_PARM_DESC(autoidle, "Enable OMAP3ISP AUTOIDLE support"); |
| |
| static void isp_save_ctx(struct isp_device *isp); |
| |
| static void isp_restore_ctx(struct isp_device *isp); |
| |
| static const struct isp_res_mapping isp_res_maps[] = { |
| { |
| .isp_rev = ISP_REVISION_2_0, |
| .offset = { |
| /* first MMIO area */ |
| 0x0000, /* base, len 0x0070 */ |
| 0x0400, /* ccp2, len 0x01f0 */ |
| 0x0600, /* ccdc, len 0x00a8 */ |
| 0x0a00, /* hist, len 0x0048 */ |
| 0x0c00, /* h3a, len 0x0060 */ |
| 0x0e00, /* preview, len 0x00a0 */ |
| 0x1000, /* resizer, len 0x00ac */ |
| 0x1200, /* sbl, len 0x00fc */ |
| /* second MMIO area */ |
| 0x0000, /* csi2a, len 0x0170 */ |
| 0x0170, /* csiphy2, len 0x000c */ |
| }, |
| .phy_type = ISP_PHY_TYPE_3430, |
| }, |
| { |
| .isp_rev = ISP_REVISION_15_0, |
| .offset = { |
| /* first MMIO area */ |
| 0x0000, /* base, len 0x0070 */ |
| 0x0400, /* ccp2, len 0x01f0 */ |
| 0x0600, /* ccdc, len 0x00a8 */ |
| 0x0a00, /* hist, len 0x0048 */ |
| 0x0c00, /* h3a, len 0x0060 */ |
| 0x0e00, /* preview, len 0x00a0 */ |
| 0x1000, /* resizer, len 0x00ac */ |
| 0x1200, /* sbl, len 0x00fc */ |
| /* second MMIO area */ |
| 0x0000, /* csi2a, len 0x0170 (1st area) */ |
| 0x0170, /* csiphy2, len 0x000c */ |
| 0x01c0, /* csi2a, len 0x0040 (2nd area) */ |
| 0x0400, /* csi2c, len 0x0170 (1st area) */ |
| 0x0570, /* csiphy1, len 0x000c */ |
| 0x05c0, /* csi2c, len 0x0040 (2nd area) */ |
| }, |
| .phy_type = ISP_PHY_TYPE_3630, |
| }, |
| }; |
| |
| /* Structure for saving/restoring ISP module registers */ |
| static struct isp_reg isp_reg_list[] = { |
| {OMAP3_ISP_IOMEM_MAIN, ISP_SYSCONFIG, 0}, |
| {OMAP3_ISP_IOMEM_MAIN, ISP_CTRL, 0}, |
| {OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0}, |
| {0, ISP_TOK_TERM, 0} |
| }; |
| |
| /* |
| * omap3isp_flush - Post pending L3 bus writes by doing a register readback |
| * @isp: OMAP3 ISP device |
| * |
| * In order to force posting of pending writes, we need to write and |
| * readback the same register, in this case the revision register. |
| * |
| * See this link for reference: |
| * https://www.mail-archive.com/linux-omap@vger.kernel.org/msg08149.html |
| */ |
| void omap3isp_flush(struct isp_device *isp) |
| { |
| isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_MAIN, ISP_REVISION); |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_REVISION); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * XCLK |
| */ |
| |
| #define to_isp_xclk(_hw) container_of(_hw, struct isp_xclk, hw) |
| |
| static void isp_xclk_update(struct isp_xclk *xclk, u32 divider) |
| { |
| switch (xclk->id) { |
| case ISP_XCLK_A: |
| isp_reg_clr_set(xclk->isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, |
| ISPTCTRL_CTRL_DIVA_MASK, |
| divider << ISPTCTRL_CTRL_DIVA_SHIFT); |
| break; |
| case ISP_XCLK_B: |
| isp_reg_clr_set(xclk->isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, |
| ISPTCTRL_CTRL_DIVB_MASK, |
| divider << ISPTCTRL_CTRL_DIVB_SHIFT); |
| break; |
| } |
| } |
| |
| static int isp_xclk_prepare(struct clk_hw *hw) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| |
| omap3isp_get(xclk->isp); |
| |
| return 0; |
| } |
| |
| static void isp_xclk_unprepare(struct clk_hw *hw) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| |
| omap3isp_put(xclk->isp); |
| } |
| |
| static int isp_xclk_enable(struct clk_hw *hw) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&xclk->lock, flags); |
| isp_xclk_update(xclk, xclk->divider); |
| xclk->enabled = true; |
| spin_unlock_irqrestore(&xclk->lock, flags); |
| |
| return 0; |
| } |
| |
| static void isp_xclk_disable(struct clk_hw *hw) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&xclk->lock, flags); |
| isp_xclk_update(xclk, 0); |
| xclk->enabled = false; |
| spin_unlock_irqrestore(&xclk->lock, flags); |
| } |
| |
| static unsigned long isp_xclk_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| |
| return parent_rate / xclk->divider; |
| } |
| |
| static u32 isp_xclk_calc_divider(unsigned long *rate, unsigned long parent_rate) |
| { |
| u32 divider; |
| |
| if (*rate >= parent_rate) { |
| *rate = parent_rate; |
| return ISPTCTRL_CTRL_DIV_BYPASS; |
| } |
| |
| if (*rate == 0) |
| *rate = 1; |
| |
| divider = DIV_ROUND_CLOSEST(parent_rate, *rate); |
| if (divider >= ISPTCTRL_CTRL_DIV_BYPASS) |
| divider = ISPTCTRL_CTRL_DIV_BYPASS - 1; |
| |
| *rate = parent_rate / divider; |
| return divider; |
| } |
| |
| static long isp_xclk_round_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long *parent_rate) |
| { |
| isp_xclk_calc_divider(&rate, *parent_rate); |
| return rate; |
| } |
| |
| static int isp_xclk_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct isp_xclk *xclk = to_isp_xclk(hw); |
| unsigned long flags; |
| u32 divider; |
| |
| divider = isp_xclk_calc_divider(&rate, parent_rate); |
| |
| spin_lock_irqsave(&xclk->lock, flags); |
| |
| xclk->divider = divider; |
| if (xclk->enabled) |
| isp_xclk_update(xclk, divider); |
| |
| spin_unlock_irqrestore(&xclk->lock, flags); |
| |
| dev_dbg(xclk->isp->dev, "%s: cam_xclk%c set to %lu Hz (div %u)\n", |
| __func__, xclk->id == ISP_XCLK_A ? 'a' : 'b', rate, divider); |
| return 0; |
| } |
| |
| static const struct clk_ops isp_xclk_ops = { |
| .prepare = isp_xclk_prepare, |
| .unprepare = isp_xclk_unprepare, |
| .enable = isp_xclk_enable, |
| .disable = isp_xclk_disable, |
| .recalc_rate = isp_xclk_recalc_rate, |
| .round_rate = isp_xclk_round_rate, |
| .set_rate = isp_xclk_set_rate, |
| }; |
| |
| static const char *isp_xclk_parent_name = "cam_mclk"; |
| |
| static struct clk *isp_xclk_src_get(struct of_phandle_args *clkspec, void *data) |
| { |
| unsigned int idx = clkspec->args[0]; |
| struct isp_device *isp = data; |
| |
| if (idx >= ARRAY_SIZE(isp->xclks)) |
| return ERR_PTR(-ENOENT); |
| |
| return isp->xclks[idx].clk; |
| } |
| |
| static int isp_xclk_init(struct isp_device *isp) |
| { |
| struct device_node *np = isp->dev->of_node; |
| struct clk_init_data init = {}; |
| unsigned int i; |
| |
| for (i = 0; i < ARRAY_SIZE(isp->xclks); ++i) |
| isp->xclks[i].clk = ERR_PTR(-EINVAL); |
| |
| for (i = 0; i < ARRAY_SIZE(isp->xclks); ++i) { |
| struct isp_xclk *xclk = &isp->xclks[i]; |
| |
| xclk->isp = isp; |
| xclk->id = i == 0 ? ISP_XCLK_A : ISP_XCLK_B; |
| xclk->divider = 1; |
| spin_lock_init(&xclk->lock); |
| |
| init.name = i == 0 ? "cam_xclka" : "cam_xclkb"; |
| init.ops = &isp_xclk_ops; |
| init.parent_names = &isp_xclk_parent_name; |
| init.num_parents = 1; |
| |
| xclk->hw.init = &init; |
| /* |
| * The first argument is NULL in order to avoid circular |
| * reference, as this driver takes reference on the |
| * sensor subdevice modules and the sensors would take |
| * reference on this module through clk_get(). |
| */ |
| xclk->clk = clk_register(NULL, &xclk->hw); |
| if (IS_ERR(xclk->clk)) |
| return PTR_ERR(xclk->clk); |
| } |
| |
| if (np) |
| of_clk_add_provider(np, isp_xclk_src_get, isp); |
| |
| return 0; |
| } |
| |
| static void isp_xclk_cleanup(struct isp_device *isp) |
| { |
| struct device_node *np = isp->dev->of_node; |
| unsigned int i; |
| |
| if (np) |
| of_clk_del_provider(np); |
| |
| for (i = 0; i < ARRAY_SIZE(isp->xclks); ++i) { |
| struct isp_xclk *xclk = &isp->xclks[i]; |
| |
| if (!IS_ERR(xclk->clk)) |
| clk_unregister(xclk->clk); |
| } |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Interrupts |
| */ |
| |
| /* |
| * isp_enable_interrupts - Enable ISP interrupts. |
| * @isp: OMAP3 ISP device |
| */ |
| static void isp_enable_interrupts(struct isp_device *isp) |
| { |
| static const u32 irq = IRQ0ENABLE_CSIA_IRQ |
| | IRQ0ENABLE_CSIB_IRQ |
| | IRQ0ENABLE_CCDC_LSC_PREF_ERR_IRQ |
| | IRQ0ENABLE_CCDC_LSC_DONE_IRQ |
| | IRQ0ENABLE_CCDC_VD0_IRQ |
| | IRQ0ENABLE_CCDC_VD1_IRQ |
| | IRQ0ENABLE_HS_VS_IRQ |
| | IRQ0ENABLE_HIST_DONE_IRQ |
| | IRQ0ENABLE_H3A_AWB_DONE_IRQ |
| | IRQ0ENABLE_H3A_AF_DONE_IRQ |
| | IRQ0ENABLE_PRV_DONE_IRQ |
| | IRQ0ENABLE_RSZ_DONE_IRQ; |
| |
| isp_reg_writel(isp, irq, OMAP3_ISP_IOMEM_MAIN, ISP_IRQ0STATUS); |
| isp_reg_writel(isp, irq, OMAP3_ISP_IOMEM_MAIN, ISP_IRQ0ENABLE); |
| } |
| |
| /* |
| * isp_disable_interrupts - Disable ISP interrupts. |
| * @isp: OMAP3 ISP device |
| */ |
| static void isp_disable_interrupts(struct isp_device *isp) |
| { |
| isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_MAIN, ISP_IRQ0ENABLE); |
| } |
| |
| /* |
| * isp_core_init - ISP core settings |
| * @isp: OMAP3 ISP device |
| * @idle: Consider idle state. |
| * |
| * Set the power settings for the ISP and SBL bus and configure the HS/VS |
| * interrupt source. |
| * |
| * We need to configure the HS/VS interrupt source before interrupts get |
| * enabled, as the sensor might be free-running and the ISP default setting |
| * (HS edge) would put an unnecessary burden on the CPU. |
| */ |
| static void isp_core_init(struct isp_device *isp, int idle) |
| { |
| isp_reg_writel(isp, |
| ((idle ? ISP_SYSCONFIG_MIDLEMODE_SMARTSTANDBY : |
| ISP_SYSCONFIG_MIDLEMODE_FORCESTANDBY) << |
| ISP_SYSCONFIG_MIDLEMODE_SHIFT) | |
| ((isp->revision == ISP_REVISION_15_0) ? |
| ISP_SYSCONFIG_AUTOIDLE : 0), |
| OMAP3_ISP_IOMEM_MAIN, ISP_SYSCONFIG); |
| |
| isp_reg_writel(isp, |
| (isp->autoidle ? ISPCTRL_SBL_AUTOIDLE : 0) | |
| ISPCTRL_SYNC_DETECT_VSRISE, |
| OMAP3_ISP_IOMEM_MAIN, ISP_CTRL); |
| } |
| |
| /* |
| * Configure the bridge and lane shifter. Valid inputs are |
| * |
| * CCDC_INPUT_PARALLEL: Parallel interface |
| * CCDC_INPUT_CSI2A: CSI2a receiver |
| * CCDC_INPUT_CCP2B: CCP2b receiver |
| * CCDC_INPUT_CSI2C: CSI2c receiver |
| * |
| * The bridge and lane shifter are configured according to the selected input |
| * and the ISP platform data. |
| */ |
| void omap3isp_configure_bridge(struct isp_device *isp, |
| enum ccdc_input_entity input, |
| const struct isp_parallel_cfg *parcfg, |
| unsigned int shift, unsigned int bridge) |
| { |
| u32 ispctrl_val; |
| |
| ispctrl_val = isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_CTRL); |
| ispctrl_val &= ~ISPCTRL_SHIFT_MASK; |
| ispctrl_val &= ~ISPCTRL_PAR_CLK_POL_INV; |
| ispctrl_val &= ~ISPCTRL_PAR_SER_CLK_SEL_MASK; |
| ispctrl_val &= ~ISPCTRL_PAR_BRIDGE_MASK; |
| ispctrl_val |= bridge; |
| |
| switch (input) { |
| case CCDC_INPUT_PARALLEL: |
| ispctrl_val |= ISPCTRL_PAR_SER_CLK_SEL_PARALLEL; |
| ispctrl_val |= parcfg->clk_pol << ISPCTRL_PAR_CLK_POL_SHIFT; |
| shift += parcfg->data_lane_shift; |
| break; |
| |
| case CCDC_INPUT_CSI2A: |
| ispctrl_val |= ISPCTRL_PAR_SER_CLK_SEL_CSIA; |
| break; |
| |
| case CCDC_INPUT_CCP2B: |
| ispctrl_val |= ISPCTRL_PAR_SER_CLK_SEL_CSIB; |
| break; |
| |
| case CCDC_INPUT_CSI2C: |
| ispctrl_val |= ISPCTRL_PAR_SER_CLK_SEL_CSIC; |
| break; |
| |
| default: |
| return; |
| } |
| |
| ispctrl_val |= ((shift/2) << ISPCTRL_SHIFT_SHIFT) & ISPCTRL_SHIFT_MASK; |
| |
| isp_reg_writel(isp, ispctrl_val, OMAP3_ISP_IOMEM_MAIN, ISP_CTRL); |
| } |
| |
| void omap3isp_hist_dma_done(struct isp_device *isp) |
| { |
| if (omap3isp_ccdc_busy(&isp->isp_ccdc) || |
| omap3isp_stat_pcr_busy(&isp->isp_hist)) { |
| /* Histogram cannot be enabled in this frame anymore */ |
| atomic_set(&isp->isp_hist.buf_err, 1); |
| dev_dbg(isp->dev, |
| "hist: Out of synchronization with CCDC. Ignoring next buffer.\n"); |
| } |
| } |
| |
| static inline void isp_isr_dbg(struct isp_device *isp, u32 irqstatus) |
| { |
| static const char *name[] = { |
| "CSIA_IRQ", |
| "res1", |
| "res2", |
| "CSIB_LCM_IRQ", |
| "CSIB_IRQ", |
| "res5", |
| "res6", |
| "res7", |
| "CCDC_VD0_IRQ", |
| "CCDC_VD1_IRQ", |
| "CCDC_VD2_IRQ", |
| "CCDC_ERR_IRQ", |
| "H3A_AF_DONE_IRQ", |
| "H3A_AWB_DONE_IRQ", |
| "res14", |
| "res15", |
| "HIST_DONE_IRQ", |
| "CCDC_LSC_DONE", |
| "CCDC_LSC_PREFETCH_COMPLETED", |
| "CCDC_LSC_PREFETCH_ERROR", |
| "PRV_DONE_IRQ", |
| "CBUFF_IRQ", |
| "res22", |
| "res23", |
| "RSZ_DONE_IRQ", |
| "OVF_IRQ", |
| "res26", |
| "res27", |
| "MMU_ERR_IRQ", |
| "OCP_ERR_IRQ", |
| "SEC_ERR_IRQ", |
| "HS_VS_IRQ", |
| }; |
| int i; |
| |
| dev_dbg(isp->dev, "ISP IRQ: "); |
| |
| for (i = 0; i < ARRAY_SIZE(name); i++) { |
| if ((1 << i) & irqstatus) |
| printk(KERN_CONT "%s ", name[i]); |
| } |
| printk(KERN_CONT "\n"); |
| } |
| |
| static void isp_isr_sbl(struct isp_device *isp) |
| { |
| struct device *dev = isp->dev; |
| struct isp_pipeline *pipe; |
| u32 sbl_pcr; |
| |
| /* |
| * Handle shared buffer logic overflows for video buffers. |
| * ISPSBL_PCR_CCDCPRV_2_RSZ_OVF can be safely ignored. |
| */ |
| sbl_pcr = isp_reg_readl(isp, OMAP3_ISP_IOMEM_SBL, ISPSBL_PCR); |
| isp_reg_writel(isp, sbl_pcr, OMAP3_ISP_IOMEM_SBL, ISPSBL_PCR); |
| sbl_pcr &= ~ISPSBL_PCR_CCDCPRV_2_RSZ_OVF; |
| |
| if (sbl_pcr) |
| dev_dbg(dev, "SBL overflow (PCR = 0x%08x)\n", sbl_pcr); |
| |
| if (sbl_pcr & ISPSBL_PCR_CSIB_WBL_OVF) { |
| pipe = to_isp_pipeline(&isp->isp_ccp2.subdev.entity); |
| if (pipe != NULL) |
| pipe->error = true; |
| } |
| |
| if (sbl_pcr & ISPSBL_PCR_CSIA_WBL_OVF) { |
| pipe = to_isp_pipeline(&isp->isp_csi2a.subdev.entity); |
| if (pipe != NULL) |
| pipe->error = true; |
| } |
| |
| if (sbl_pcr & ISPSBL_PCR_CCDC_WBL_OVF) { |
| pipe = to_isp_pipeline(&isp->isp_ccdc.subdev.entity); |
| if (pipe != NULL) |
| pipe->error = true; |
| } |
| |
| if (sbl_pcr & ISPSBL_PCR_PRV_WBL_OVF) { |
| pipe = to_isp_pipeline(&isp->isp_prev.subdev.entity); |
| if (pipe != NULL) |
| pipe->error = true; |
| } |
| |
| if (sbl_pcr & (ISPSBL_PCR_RSZ1_WBL_OVF |
| | ISPSBL_PCR_RSZ2_WBL_OVF |
| | ISPSBL_PCR_RSZ3_WBL_OVF |
| | ISPSBL_PCR_RSZ4_WBL_OVF)) { |
| pipe = to_isp_pipeline(&isp->isp_res.subdev.entity); |
| if (pipe != NULL) |
| pipe->error = true; |
| } |
| |
| if (sbl_pcr & ISPSBL_PCR_H3A_AF_WBL_OVF) |
| omap3isp_stat_sbl_overflow(&isp->isp_af); |
| |
| if (sbl_pcr & ISPSBL_PCR_H3A_AEAWB_WBL_OVF) |
| omap3isp_stat_sbl_overflow(&isp->isp_aewb); |
| } |
| |
| /* |
| * isp_isr - Interrupt Service Routine for Camera ISP module. |
| * @irq: Not used currently. |
| * @_isp: Pointer to the OMAP3 ISP device |
| * |
| * Handles the corresponding callback if plugged in. |
| */ |
| static irqreturn_t isp_isr(int irq, void *_isp) |
| { |
| static const u32 ccdc_events = IRQ0STATUS_CCDC_LSC_PREF_ERR_IRQ | |
| IRQ0STATUS_CCDC_LSC_DONE_IRQ | |
| IRQ0STATUS_CCDC_VD0_IRQ | |
| IRQ0STATUS_CCDC_VD1_IRQ | |
| IRQ0STATUS_HS_VS_IRQ; |
| struct isp_device *isp = _isp; |
| u32 irqstatus; |
| |
| irqstatus = isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_IRQ0STATUS); |
| isp_reg_writel(isp, irqstatus, OMAP3_ISP_IOMEM_MAIN, ISP_IRQ0STATUS); |
| |
| isp_isr_sbl(isp); |
| |
| if (irqstatus & IRQ0STATUS_CSIA_IRQ) |
| omap3isp_csi2_isr(&isp->isp_csi2a); |
| |
| if (irqstatus & IRQ0STATUS_CSIB_IRQ) |
| omap3isp_ccp2_isr(&isp->isp_ccp2); |
| |
| if (irqstatus & IRQ0STATUS_CCDC_VD0_IRQ) { |
| if (isp->isp_ccdc.output & CCDC_OUTPUT_PREVIEW) |
| omap3isp_preview_isr_frame_sync(&isp->isp_prev); |
| if (isp->isp_ccdc.output & CCDC_OUTPUT_RESIZER) |
| omap3isp_resizer_isr_frame_sync(&isp->isp_res); |
| omap3isp_stat_isr_frame_sync(&isp->isp_aewb); |
| omap3isp_stat_isr_frame_sync(&isp->isp_af); |
| omap3isp_stat_isr_frame_sync(&isp->isp_hist); |
| } |
| |
| if (irqstatus & ccdc_events) |
| omap3isp_ccdc_isr(&isp->isp_ccdc, irqstatus & ccdc_events); |
| |
| if (irqstatus & IRQ0STATUS_PRV_DONE_IRQ) { |
| if (isp->isp_prev.output & PREVIEW_OUTPUT_RESIZER) |
| omap3isp_resizer_isr_frame_sync(&isp->isp_res); |
| omap3isp_preview_isr(&isp->isp_prev); |
| } |
| |
| if (irqstatus & IRQ0STATUS_RSZ_DONE_IRQ) |
| omap3isp_resizer_isr(&isp->isp_res); |
| |
| if (irqstatus & IRQ0STATUS_H3A_AWB_DONE_IRQ) |
| omap3isp_stat_isr(&isp->isp_aewb); |
| |
| if (irqstatus & IRQ0STATUS_H3A_AF_DONE_IRQ) |
| omap3isp_stat_isr(&isp->isp_af); |
| |
| if (irqstatus & IRQ0STATUS_HIST_DONE_IRQ) |
| omap3isp_stat_isr(&isp->isp_hist); |
| |
| omap3isp_flush(isp); |
| |
| #if defined(DEBUG) && defined(ISP_ISR_DEBUG) |
| isp_isr_dbg(isp, irqstatus); |
| #endif |
| |
| return IRQ_HANDLED; |
| } |
| |
| static const struct media_device_ops isp_media_ops = { |
| .link_notify = v4l2_pipeline_link_notify, |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * Pipeline stream management |
| */ |
| |
| /* |
| * isp_pipeline_enable - Enable streaming on a pipeline |
| * @pipe: ISP pipeline |
| * @mode: Stream mode (single shot or continuous) |
| * |
| * Walk the entities chain starting at the pipeline output video node and start |
| * all modules in the chain in the given mode. |
| * |
| * Return 0 if successful, or the return value of the failed video::s_stream |
| * operation otherwise. |
| */ |
| static int isp_pipeline_enable(struct isp_pipeline *pipe, |
| enum isp_pipeline_stream_state mode) |
| { |
| struct isp_device *isp = pipe->output->isp; |
| struct media_entity *entity; |
| struct media_pad *pad; |
| struct v4l2_subdev *subdev; |
| unsigned long flags; |
| int ret; |
| |
| /* Refuse to start streaming if an entity included in the pipeline has |
| * crashed. This check must be performed before the loop below to avoid |
| * starting entities if the pipeline won't start anyway (those entities |
| * would then likely fail to stop, making the problem worse). |
| */ |
| if (media_entity_enum_intersects(&pipe->ent_enum, &isp->crashed)) |
| return -EIO; |
| |
| spin_lock_irqsave(&pipe->lock, flags); |
| pipe->state &= ~(ISP_PIPELINE_IDLE_INPUT | ISP_PIPELINE_IDLE_OUTPUT); |
| spin_unlock_irqrestore(&pipe->lock, flags); |
| |
| pipe->do_propagation = false; |
| |
| mutex_lock(&isp->media_dev.graph_mutex); |
| |
| entity = &pipe->output->video.entity; |
| while (1) { |
| pad = &entity->pads[0]; |
| if (!(pad->flags & MEDIA_PAD_FL_SINK)) |
| break; |
| |
| pad = media_entity_remote_pad(pad); |
| if (!pad || !is_media_entity_v4l2_subdev(pad->entity)) |
| break; |
| |
| entity = pad->entity; |
| subdev = media_entity_to_v4l2_subdev(entity); |
| |
| ret = v4l2_subdev_call(subdev, video, s_stream, mode); |
| if (ret < 0 && ret != -ENOIOCTLCMD) { |
| mutex_unlock(&isp->media_dev.graph_mutex); |
| return ret; |
| } |
| |
| if (subdev == &isp->isp_ccdc.subdev) { |
| v4l2_subdev_call(&isp->isp_aewb.subdev, video, |
| s_stream, mode); |
| v4l2_subdev_call(&isp->isp_af.subdev, video, |
| s_stream, mode); |
| v4l2_subdev_call(&isp->isp_hist.subdev, video, |
| s_stream, mode); |
| pipe->do_propagation = true; |
| } |
| |
| /* Stop at the first external sub-device. */ |
| if (subdev->dev != isp->dev) |
| break; |
| } |
| |
| mutex_unlock(&isp->media_dev.graph_mutex); |
| |
| return 0; |
| } |
| |
| static int isp_pipeline_wait_resizer(struct isp_device *isp) |
| { |
| return omap3isp_resizer_busy(&isp->isp_res); |
| } |
| |
| static int isp_pipeline_wait_preview(struct isp_device *isp) |
| { |
| return omap3isp_preview_busy(&isp->isp_prev); |
| } |
| |
| static int isp_pipeline_wait_ccdc(struct isp_device *isp) |
| { |
| return omap3isp_stat_busy(&isp->isp_af) |
| || omap3isp_stat_busy(&isp->isp_aewb) |
| || omap3isp_stat_busy(&isp->isp_hist) |
| || omap3isp_ccdc_busy(&isp->isp_ccdc); |
| } |
| |
| #define ISP_STOP_TIMEOUT msecs_to_jiffies(1000) |
| |
| static int isp_pipeline_wait(struct isp_device *isp, |
| int(*busy)(struct isp_device *isp)) |
| { |
| unsigned long timeout = jiffies + ISP_STOP_TIMEOUT; |
| |
| while (!time_after(jiffies, timeout)) { |
| if (!busy(isp)) |
| return 0; |
| } |
| |
| return 1; |
| } |
| |
| /* |
| * isp_pipeline_disable - Disable streaming on a pipeline |
| * @pipe: ISP pipeline |
| * |
| * Walk the entities chain starting at the pipeline output video node and stop |
| * all modules in the chain. Wait synchronously for the modules to be stopped if |
| * necessary. |
| * |
| * Return 0 if all modules have been properly stopped, or -ETIMEDOUT if a module |
| * can't be stopped (in which case a software reset of the ISP is probably |
| * necessary). |
| */ |
| static int isp_pipeline_disable(struct isp_pipeline *pipe) |
| { |
| struct isp_device *isp = pipe->output->isp; |
| struct media_entity *entity; |
| struct media_pad *pad; |
| struct v4l2_subdev *subdev; |
| int failure = 0; |
| int ret; |
| |
| /* |
| * We need to stop all the modules after CCDC first or they'll |
| * never stop since they may not get a full frame from CCDC. |
| */ |
| entity = &pipe->output->video.entity; |
| while (1) { |
| pad = &entity->pads[0]; |
| if (!(pad->flags & MEDIA_PAD_FL_SINK)) |
| break; |
| |
| pad = media_entity_remote_pad(pad); |
| if (!pad || !is_media_entity_v4l2_subdev(pad->entity)) |
| break; |
| |
| entity = pad->entity; |
| subdev = media_entity_to_v4l2_subdev(entity); |
| |
| if (subdev == &isp->isp_ccdc.subdev) { |
| v4l2_subdev_call(&isp->isp_aewb.subdev, |
| video, s_stream, 0); |
| v4l2_subdev_call(&isp->isp_af.subdev, |
| video, s_stream, 0); |
| v4l2_subdev_call(&isp->isp_hist.subdev, |
| video, s_stream, 0); |
| } |
| |
| ret = v4l2_subdev_call(subdev, video, s_stream, 0); |
| |
| /* Stop at the first external sub-device. */ |
| if (subdev->dev != isp->dev) |
| break; |
| |
| if (subdev == &isp->isp_res.subdev) |
| ret |= isp_pipeline_wait(isp, isp_pipeline_wait_resizer); |
| else if (subdev == &isp->isp_prev.subdev) |
| ret |= isp_pipeline_wait(isp, isp_pipeline_wait_preview); |
| else if (subdev == &isp->isp_ccdc.subdev) |
| ret |= isp_pipeline_wait(isp, isp_pipeline_wait_ccdc); |
| |
| /* Handle stop failures. An entity that fails to stop can |
| * usually just be restarted. Flag the stop failure nonetheless |
| * to trigger an ISP reset the next time the device is released, |
| * just in case. |
| * |
| * The preview engine is a special case. A failure to stop can |
| * mean a hardware crash. When that happens the preview engine |
| * won't respond to read/write operations on the L4 bus anymore, |
| * resulting in a bus fault and a kernel oops next time it gets |
| * accessed. Mark it as crashed to prevent pipelines including |
| * it from being started. |
| */ |
| if (ret) { |
| dev_info(isp->dev, "Unable to stop %s\n", subdev->name); |
| isp->stop_failure = true; |
| if (subdev == &isp->isp_prev.subdev) |
| media_entity_enum_set(&isp->crashed, |
| &subdev->entity); |
| failure = -ETIMEDOUT; |
| } |
| } |
| |
| return failure; |
| } |
| |
| /* |
| * omap3isp_pipeline_set_stream - Enable/disable streaming on a pipeline |
| * @pipe: ISP pipeline |
| * @state: Stream state (stopped, single shot or continuous) |
| * |
| * Set the pipeline to the given stream state. Pipelines can be started in |
| * single-shot or continuous mode. |
| * |
| * Return 0 if successful, or the return value of the failed video::s_stream |
| * operation otherwise. The pipeline state is not updated when the operation |
| * fails, except when stopping the pipeline. |
| */ |
| int omap3isp_pipeline_set_stream(struct isp_pipeline *pipe, |
| enum isp_pipeline_stream_state state) |
| { |
| int ret; |
| |
| if (state == ISP_PIPELINE_STREAM_STOPPED) |
| ret = isp_pipeline_disable(pipe); |
| else |
| ret = isp_pipeline_enable(pipe, state); |
| |
| if (ret == 0 || state == ISP_PIPELINE_STREAM_STOPPED) |
| pipe->stream_state = state; |
| |
| return ret; |
| } |
| |
| /* |
| * omap3isp_pipeline_cancel_stream - Cancel stream on a pipeline |
| * @pipe: ISP pipeline |
| * |
| * Cancelling a stream mark all buffers on all video nodes in the pipeline as |
| * erroneous and makes sure no new buffer can be queued. This function is called |
| * when a fatal error that prevents any further operation on the pipeline |
| * occurs. |
| */ |
| void omap3isp_pipeline_cancel_stream(struct isp_pipeline *pipe) |
| { |
| if (pipe->input) |
| omap3isp_video_cancel_stream(pipe->input); |
| if (pipe->output) |
| omap3isp_video_cancel_stream(pipe->output); |
| } |
| |
| /* |
| * isp_pipeline_resume - Resume streaming on a pipeline |
| * @pipe: ISP pipeline |
| * |
| * Resume video output and input and re-enable pipeline. |
| */ |
| static void isp_pipeline_resume(struct isp_pipeline *pipe) |
| { |
| int singleshot = pipe->stream_state == ISP_PIPELINE_STREAM_SINGLESHOT; |
| |
| omap3isp_video_resume(pipe->output, !singleshot); |
| if (singleshot) |
| omap3isp_video_resume(pipe->input, 0); |
| isp_pipeline_enable(pipe, pipe->stream_state); |
| } |
| |
| /* |
| * isp_pipeline_suspend - Suspend streaming on a pipeline |
| * @pipe: ISP pipeline |
| * |
| * Suspend pipeline. |
| */ |
| static void isp_pipeline_suspend(struct isp_pipeline *pipe) |
| { |
| isp_pipeline_disable(pipe); |
| } |
| |
| /* |
| * isp_pipeline_is_last - Verify if entity has an enabled link to the output |
| * video node |
| * @me: ISP module's media entity |
| * |
| * Returns 1 if the entity has an enabled link to the output video node or 0 |
| * otherwise. It's true only while pipeline can have no more than one output |
| * node. |
| */ |
| static int isp_pipeline_is_last(struct media_entity *me) |
| { |
| struct isp_pipeline *pipe; |
| struct media_pad *pad; |
| |
| if (!me->pipe) |
| return 0; |
| pipe = to_isp_pipeline(me); |
| if (pipe->stream_state == ISP_PIPELINE_STREAM_STOPPED) |
| return 0; |
| pad = media_entity_remote_pad(&pipe->output->pad); |
| return pad->entity == me; |
| } |
| |
| /* |
| * isp_suspend_module_pipeline - Suspend pipeline to which belongs the module |
| * @me: ISP module's media entity |
| * |
| * Suspend the whole pipeline if module's entity has an enabled link to the |
| * output video node. It works only while pipeline can have no more than one |
| * output node. |
| */ |
| static void isp_suspend_module_pipeline(struct media_entity *me) |
| { |
| if (isp_pipeline_is_last(me)) |
| isp_pipeline_suspend(to_isp_pipeline(me)); |
| } |
| |
| /* |
| * isp_resume_module_pipeline - Resume pipeline to which belongs the module |
| * @me: ISP module's media entity |
| * |
| * Resume the whole pipeline if module's entity has an enabled link to the |
| * output video node. It works only while pipeline can have no more than one |
| * output node. |
| */ |
| static void isp_resume_module_pipeline(struct media_entity *me) |
| { |
| if (isp_pipeline_is_last(me)) |
| isp_pipeline_resume(to_isp_pipeline(me)); |
| } |
| |
| /* |
| * isp_suspend_modules - Suspend ISP submodules. |
| * @isp: OMAP3 ISP device |
| * |
| * Returns 0 if suspend left in idle state all the submodules properly, |
| * or returns 1 if a general Reset is required to suspend the submodules. |
| */ |
| static int __maybe_unused isp_suspend_modules(struct isp_device *isp) |
| { |
| unsigned long timeout; |
| |
| omap3isp_stat_suspend(&isp->isp_aewb); |
| omap3isp_stat_suspend(&isp->isp_af); |
| omap3isp_stat_suspend(&isp->isp_hist); |
| isp_suspend_module_pipeline(&isp->isp_res.subdev.entity); |
| isp_suspend_module_pipeline(&isp->isp_prev.subdev.entity); |
| isp_suspend_module_pipeline(&isp->isp_ccdc.subdev.entity); |
| isp_suspend_module_pipeline(&isp->isp_csi2a.subdev.entity); |
| isp_suspend_module_pipeline(&isp->isp_ccp2.subdev.entity); |
| |
| timeout = jiffies + ISP_STOP_TIMEOUT; |
| while (omap3isp_stat_busy(&isp->isp_af) |
| || omap3isp_stat_busy(&isp->isp_aewb) |
| || omap3isp_stat_busy(&isp->isp_hist) |
| || omap3isp_preview_busy(&isp->isp_prev) |
| || omap3isp_resizer_busy(&isp->isp_res) |
| || omap3isp_ccdc_busy(&isp->isp_ccdc)) { |
| if (time_after(jiffies, timeout)) { |
| dev_info(isp->dev, "can't stop modules.\n"); |
| return 1; |
| } |
| msleep(1); |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * isp_resume_modules - Resume ISP submodules. |
| * @isp: OMAP3 ISP device |
| */ |
| static void __maybe_unused isp_resume_modules(struct isp_device *isp) |
| { |
| omap3isp_stat_resume(&isp->isp_aewb); |
| omap3isp_stat_resume(&isp->isp_af); |
| omap3isp_stat_resume(&isp->isp_hist); |
| isp_resume_module_pipeline(&isp->isp_res.subdev.entity); |
| isp_resume_module_pipeline(&isp->isp_prev.subdev.entity); |
| isp_resume_module_pipeline(&isp->isp_ccdc.subdev.entity); |
| isp_resume_module_pipeline(&isp->isp_csi2a.subdev.entity); |
| isp_resume_module_pipeline(&isp->isp_ccp2.subdev.entity); |
| } |
| |
| /* |
| * isp_reset - Reset ISP with a timeout wait for idle. |
| * @isp: OMAP3 ISP device |
| */ |
| static int isp_reset(struct isp_device *isp) |
| { |
| unsigned long timeout = 0; |
| |
| isp_reg_writel(isp, |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_SYSCONFIG) |
| | ISP_SYSCONFIG_SOFTRESET, |
| OMAP3_ISP_IOMEM_MAIN, ISP_SYSCONFIG); |
| while (!(isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, |
| ISP_SYSSTATUS) & 0x1)) { |
| if (timeout++ > 10000) { |
| dev_alert(isp->dev, "cannot reset ISP\n"); |
| return -ETIMEDOUT; |
| } |
| udelay(1); |
| } |
| |
| isp->stop_failure = false; |
| media_entity_enum_zero(&isp->crashed); |
| return 0; |
| } |
| |
| /* |
| * isp_save_context - Saves the values of the ISP module registers. |
| * @isp: OMAP3 ISP device |
| * @reg_list: Structure containing pairs of register address and value to |
| * modify on OMAP. |
| */ |
| static void |
| isp_save_context(struct isp_device *isp, struct isp_reg *reg_list) |
| { |
| struct isp_reg *next = reg_list; |
| |
| for (; next->reg != ISP_TOK_TERM; next++) |
| next->val = isp_reg_readl(isp, next->mmio_range, next->reg); |
| } |
| |
| /* |
| * isp_restore_context - Restores the values of the ISP module registers. |
| * @isp: OMAP3 ISP device |
| * @reg_list: Structure containing pairs of register address and value to |
| * modify on OMAP. |
| */ |
| static void |
| isp_restore_context(struct isp_device *isp, struct isp_reg *reg_list) |
| { |
| struct isp_reg *next = reg_list; |
| |
| for (; next->reg != ISP_TOK_TERM; next++) |
| isp_reg_writel(isp, next->val, next->mmio_range, next->reg); |
| } |
| |
| /* |
| * isp_save_ctx - Saves ISP, CCDC, HIST, H3A, PREV, RESZ & MMU context. |
| * @isp: OMAP3 ISP device |
| * |
| * Routine for saving the context of each module in the ISP. |
| * CCDC, HIST, H3A, PREV, RESZ and MMU. |
| */ |
| static void isp_save_ctx(struct isp_device *isp) |
| { |
| isp_save_context(isp, isp_reg_list); |
| omap_iommu_save_ctx(isp->dev); |
| } |
| |
| /* |
| * isp_restore_ctx - Restores ISP, CCDC, HIST, H3A, PREV, RESZ & MMU context. |
| * @isp: OMAP3 ISP device |
| * |
| * Routine for restoring the context of each module in the ISP. |
| * CCDC, HIST, H3A, PREV, RESZ and MMU. |
| */ |
| static void isp_restore_ctx(struct isp_device *isp) |
| { |
| isp_restore_context(isp, isp_reg_list); |
| omap_iommu_restore_ctx(isp->dev); |
| omap3isp_ccdc_restore_context(isp); |
| omap3isp_preview_restore_context(isp); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * SBL resources management |
| */ |
| #define OMAP3_ISP_SBL_READ (OMAP3_ISP_SBL_CSI1_READ | \ |
| OMAP3_ISP_SBL_CCDC_LSC_READ | \ |
| OMAP3_ISP_SBL_PREVIEW_READ | \ |
| OMAP3_ISP_SBL_RESIZER_READ) |
| #define OMAP3_ISP_SBL_WRITE (OMAP3_ISP_SBL_CSI1_WRITE | \ |
| OMAP3_ISP_SBL_CSI2A_WRITE | \ |
| OMAP3_ISP_SBL_CSI2C_WRITE | \ |
| OMAP3_ISP_SBL_CCDC_WRITE | \ |
| OMAP3_ISP_SBL_PREVIEW_WRITE) |
| |
| void omap3isp_sbl_enable(struct isp_device *isp, enum isp_sbl_resource res) |
| { |
| u32 sbl = 0; |
| |
| isp->sbl_resources |= res; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_CSI1_READ) |
| sbl |= ISPCTRL_SBL_SHARED_RPORTA; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_CCDC_LSC_READ) |
| sbl |= ISPCTRL_SBL_SHARED_RPORTB; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_CSI2C_WRITE) |
| sbl |= ISPCTRL_SBL_SHARED_WPORTC; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_RESIZER_WRITE) |
| sbl |= ISPCTRL_SBL_WR0_RAM_EN; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_WRITE) |
| sbl |= ISPCTRL_SBL_WR1_RAM_EN; |
| |
| if (isp->sbl_resources & OMAP3_ISP_SBL_READ) |
| sbl |= ISPCTRL_SBL_RD_RAM_EN; |
| |
| isp_reg_set(isp, OMAP3_ISP_IOMEM_MAIN, ISP_CTRL, sbl); |
| } |
| |
| void omap3isp_sbl_disable(struct isp_device *isp, enum isp_sbl_resource res) |
| { |
| u32 sbl = 0; |
| |
| isp->sbl_resources &= ~res; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_CSI1_READ)) |
| sbl |= ISPCTRL_SBL_SHARED_RPORTA; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_CCDC_LSC_READ)) |
| sbl |= ISPCTRL_SBL_SHARED_RPORTB; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_CSI2C_WRITE)) |
| sbl |= ISPCTRL_SBL_SHARED_WPORTC; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_RESIZER_WRITE)) |
| sbl |= ISPCTRL_SBL_WR0_RAM_EN; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_WRITE)) |
| sbl |= ISPCTRL_SBL_WR1_RAM_EN; |
| |
| if (!(isp->sbl_resources & OMAP3_ISP_SBL_READ)) |
| sbl |= ISPCTRL_SBL_RD_RAM_EN; |
| |
| isp_reg_clr(isp, OMAP3_ISP_IOMEM_MAIN, ISP_CTRL, sbl); |
| } |
| |
| /* |
| * isp_module_sync_idle - Helper to sync module with its idle state |
| * @me: ISP submodule's media entity |
| * @wait: ISP submodule's wait queue for streamoff/interrupt synchronization |
| * @stopping: flag which tells module wants to stop |
| * |
| * This function checks if ISP submodule needs to wait for next interrupt. If |
| * yes, makes the caller to sleep while waiting for such event. |
| */ |
| int omap3isp_module_sync_idle(struct media_entity *me, wait_queue_head_t *wait, |
| atomic_t *stopping) |
| { |
| struct isp_pipeline *pipe = to_isp_pipeline(me); |
| |
| if (pipe->stream_state == ISP_PIPELINE_STREAM_STOPPED || |
| (pipe->stream_state == ISP_PIPELINE_STREAM_SINGLESHOT && |
| !isp_pipeline_ready(pipe))) |
| return 0; |
| |
| /* |
| * atomic_set() doesn't include memory barrier on ARM platform for SMP |
| * scenario. We'll call it here to avoid race conditions. |
| */ |
| atomic_set(stopping, 1); |
| smp_mb(); |
| |
| /* |
| * If module is the last one, it's writing to memory. In this case, |
| * it's necessary to check if the module is already paused due to |
| * DMA queue underrun or if it has to wait for next interrupt to be |
| * idle. |
| * If it isn't the last one, the function won't sleep but *stopping |
| * will still be set to warn next submodule caller's interrupt the |
| * module wants to be idle. |
| */ |
| if (isp_pipeline_is_last(me)) { |
| struct isp_video *video = pipe->output; |
| unsigned long flags; |
| spin_lock_irqsave(&video->irqlock, flags); |
| if (video->dmaqueue_flags & ISP_VIDEO_DMAQUEUE_UNDERRUN) { |
| spin_unlock_irqrestore(&video->irqlock, flags); |
| atomic_set(stopping, 0); |
| smp_mb(); |
| return 0; |
| } |
| spin_unlock_irqrestore(&video->irqlock, flags); |
| if (!wait_event_timeout(*wait, !atomic_read(stopping), |
| msecs_to_jiffies(1000))) { |
| atomic_set(stopping, 0); |
| smp_mb(); |
| return -ETIMEDOUT; |
| } |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * omap3isp_module_sync_is_stopping - Helper to verify if module was stopping |
| * @wait: ISP submodule's wait queue for streamoff/interrupt synchronization |
| * @stopping: flag which tells module wants to stop |
| * |
| * This function checks if ISP submodule was stopping. In case of yes, it |
| * notices the caller by setting stopping to 0 and waking up the wait queue. |
| * Returns 1 if it was stopping or 0 otherwise. |
| */ |
| int omap3isp_module_sync_is_stopping(wait_queue_head_t *wait, |
| atomic_t *stopping) |
| { |
| if (atomic_cmpxchg(stopping, 1, 0)) { |
| wake_up(wait); |
| return 1; |
| } |
| |
| return 0; |
| } |
| |
| /* -------------------------------------------------------------------------- |
| * Clock management |
| */ |
| |
| #define ISPCTRL_CLKS_MASK (ISPCTRL_H3A_CLK_EN | \ |
| ISPCTRL_HIST_CLK_EN | \ |
| ISPCTRL_RSZ_CLK_EN | \ |
| (ISPCTRL_CCDC_CLK_EN | ISPCTRL_CCDC_RAM_EN) | \ |
| (ISPCTRL_PREV_CLK_EN | ISPCTRL_PREV_RAM_EN)) |
| |
| static void __isp_subclk_update(struct isp_device *isp) |
| { |
| u32 clk = 0; |
| |
| /* AEWB and AF share the same clock. */ |
| if (isp->subclk_resources & |
| (OMAP3_ISP_SUBCLK_AEWB | OMAP3_ISP_SUBCLK_AF)) |
| clk |= ISPCTRL_H3A_CLK_EN; |
| |
| if (isp->subclk_resources & OMAP3_ISP_SUBCLK_HIST) |
| clk |= ISPCTRL_HIST_CLK_EN; |
| |
| if (isp->subclk_resources & OMAP3_ISP_SUBCLK_RESIZER) |
| clk |= ISPCTRL_RSZ_CLK_EN; |
| |
| /* NOTE: For CCDC & Preview submodules, we need to affect internal |
| * RAM as well. |
| */ |
| if (isp->subclk_resources & OMAP3_ISP_SUBCLK_CCDC) |
| clk |= ISPCTRL_CCDC_CLK_EN | ISPCTRL_CCDC_RAM_EN; |
| |
| if (isp->subclk_resources & OMAP3_ISP_SUBCLK_PREVIEW) |
| clk |= ISPCTRL_PREV_CLK_EN | ISPCTRL_PREV_RAM_EN; |
| |
| isp_reg_clr_set(isp, OMAP3_ISP_IOMEM_MAIN, ISP_CTRL, |
| ISPCTRL_CLKS_MASK, clk); |
| } |
| |
| void omap3isp_subclk_enable(struct isp_device *isp, |
| enum isp_subclk_resource res) |
| { |
| isp->subclk_resources |= res; |
| |
| __isp_subclk_update(isp); |
| } |
| |
| void omap3isp_subclk_disable(struct isp_device *isp, |
| enum isp_subclk_resource res) |
| { |
| isp->subclk_resources &= ~res; |
| |
| __isp_subclk_update(isp); |
| } |
| |
| /* |
| * isp_enable_clocks - Enable ISP clocks |
| * @isp: OMAP3 ISP device |
| * |
| * Return 0 if successful, or clk_prepare_enable return value if any of them |
| * fails. |
| */ |
| static int isp_enable_clocks(struct isp_device *isp) |
| { |
| int r; |
| unsigned long rate; |
| |
| r = clk_prepare_enable(isp->clock[ISP_CLK_CAM_ICK]); |
| if (r) { |
| dev_err(isp->dev, "failed to enable cam_ick clock\n"); |
| goto out_clk_enable_ick; |
| } |
| r = clk_set_rate(isp->clock[ISP_CLK_CAM_MCLK], CM_CAM_MCLK_HZ); |
| if (r) { |
| dev_err(isp->dev, "clk_set_rate for cam_mclk failed\n"); |
| goto out_clk_enable_mclk; |
| } |
| r = clk_prepare_enable(isp->clock[ISP_CLK_CAM_MCLK]); |
| if (r) { |
| dev_err(isp->dev, "failed to enable cam_mclk clock\n"); |
| goto out_clk_enable_mclk; |
| } |
| rate = clk_get_rate(isp->clock[ISP_CLK_CAM_MCLK]); |
| if (rate != CM_CAM_MCLK_HZ) |
| dev_warn(isp->dev, "unexpected cam_mclk rate:\n" |
| " expected : %d\n" |
| " actual : %ld\n", CM_CAM_MCLK_HZ, rate); |
| r = clk_prepare_enable(isp->clock[ISP_CLK_CSI2_FCK]); |
| if (r) { |
| dev_err(isp->dev, "failed to enable csi2_fck clock\n"); |
| goto out_clk_enable_csi2_fclk; |
| } |
| return 0; |
| |
| out_clk_enable_csi2_fclk: |
| clk_disable_unprepare(isp->clock[ISP_CLK_CAM_MCLK]); |
| out_clk_enable_mclk: |
| clk_disable_unprepare(isp->clock[ISP_CLK_CAM_ICK]); |
| out_clk_enable_ick: |
| return r; |
| } |
| |
| /* |
| * isp_disable_clocks - Disable ISP clocks |
| * @isp: OMAP3 ISP device |
| */ |
| static void isp_disable_clocks(struct isp_device *isp) |
| { |
| clk_disable_unprepare(isp->clock[ISP_CLK_CAM_ICK]); |
| clk_disable_unprepare(isp->clock[ISP_CLK_CAM_MCLK]); |
| clk_disable_unprepare(isp->clock[ISP_CLK_CSI2_FCK]); |
| } |
| |
| static const char *isp_clocks[] = { |
| "cam_ick", |
| "cam_mclk", |
| "csi2_96m_fck", |
| "l3_ick", |
| }; |
| |
| static int isp_get_clocks(struct isp_device *isp) |
| { |
| struct clk *clk; |
| unsigned int i; |
| |
| for (i = 0; i < ARRAY_SIZE(isp_clocks); ++i) { |
| clk = devm_clk_get(isp->dev, isp_clocks[i]); |
| if (IS_ERR(clk)) { |
| dev_err(isp->dev, "clk_get %s failed\n", isp_clocks[i]); |
| return PTR_ERR(clk); |
| } |
| |
| isp->clock[i] = clk; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * omap3isp_get - Acquire the ISP resource. |
| * |
| * Initializes the clocks for the first acquire. |
| * |
| * Increment the reference count on the ISP. If the first reference is taken, |
| * enable clocks and power-up all submodules. |
| * |
| * Return a pointer to the ISP device structure, or NULL if an error occurred. |
| */ |
| static struct isp_device *__omap3isp_get(struct isp_device *isp, bool irq) |
| { |
| struct isp_device *__isp = isp; |
| |
| if (isp == NULL) |
| return NULL; |
| |
| mutex_lock(&isp->isp_mutex); |
| if (isp->ref_count > 0) |
| goto out; |
| |
| if (isp_enable_clocks(isp) < 0) { |
| __isp = NULL; |
| goto out; |
| } |
| |
| /* We don't want to restore context before saving it! */ |
| if (isp->has_context) |
| isp_restore_ctx(isp); |
| |
| if (irq) |
| isp_enable_interrupts(isp); |
| |
| out: |
| if (__isp != NULL) |
| isp->ref_count++; |
| mutex_unlock(&isp->isp_mutex); |
| |
| return __isp; |
| } |
| |
| struct isp_device *omap3isp_get(struct isp_device *isp) |
| { |
| return __omap3isp_get(isp, true); |
| } |
| |
| /* |
| * omap3isp_put - Release the ISP |
| * |
| * Decrement the reference count on the ISP. If the last reference is released, |
| * power-down all submodules, disable clocks and free temporary buffers. |
| */ |
| static void __omap3isp_put(struct isp_device *isp, bool save_ctx) |
| { |
| if (isp == NULL) |
| return; |
| |
| mutex_lock(&isp->isp_mutex); |
| BUG_ON(isp->ref_count == 0); |
| if (--isp->ref_count == 0) { |
| isp_disable_interrupts(isp); |
| if (save_ctx) { |
| isp_save_ctx(isp); |
| isp->has_context = 1; |
| } |
| /* Reset the ISP if an entity has failed to stop. This is the |
| * only way to recover from such conditions. |
| */ |
| if (!media_entity_enum_empty(&isp->crashed) || |
| isp->stop_failure) |
| isp_reset(isp); |
| isp_disable_clocks(isp); |
| } |
| mutex_unlock(&isp->isp_mutex); |
| } |
| |
| void omap3isp_put(struct isp_device *isp) |
| { |
| __omap3isp_put(isp, true); |
| } |
| |
| /* -------------------------------------------------------------------------- |
| * Platform device driver |
| */ |
| |
| /* |
| * omap3isp_print_status - Prints the values of the ISP Control Module registers |
| * @isp: OMAP3 ISP device |
| */ |
| #define ISP_PRINT_REGISTER(isp, name)\ |
| dev_dbg(isp->dev, "###ISP " #name "=0x%08x\n", \ |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_##name)) |
| #define SBL_PRINT_REGISTER(isp, name)\ |
| dev_dbg(isp->dev, "###SBL " #name "=0x%08x\n", \ |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_SBL, ISPSBL_##name)) |
| |
| void omap3isp_print_status(struct isp_device *isp) |
| { |
| dev_dbg(isp->dev, "-------------ISP Register dump--------------\n"); |
| |
| ISP_PRINT_REGISTER(isp, SYSCONFIG); |
| ISP_PRINT_REGISTER(isp, SYSSTATUS); |
| ISP_PRINT_REGISTER(isp, IRQ0ENABLE); |
| ISP_PRINT_REGISTER(isp, IRQ0STATUS); |
| ISP_PRINT_REGISTER(isp, TCTRL_GRESET_LENGTH); |
| ISP_PRINT_REGISTER(isp, TCTRL_PSTRB_REPLAY); |
| ISP_PRINT_REGISTER(isp, CTRL); |
| ISP_PRINT_REGISTER(isp, TCTRL_CTRL); |
| ISP_PRINT_REGISTER(isp, TCTRL_FRAME); |
| ISP_PRINT_REGISTER(isp, TCTRL_PSTRB_DELAY); |
| ISP_PRINT_REGISTER(isp, TCTRL_STRB_DELAY); |
| ISP_PRINT_REGISTER(isp, TCTRL_SHUT_DELAY); |
| ISP_PRINT_REGISTER(isp, TCTRL_PSTRB_LENGTH); |
| ISP_PRINT_REGISTER(isp, TCTRL_STRB_LENGTH); |
| ISP_PRINT_REGISTER(isp, TCTRL_SHUT_LENGTH); |
| |
| SBL_PRINT_REGISTER(isp, PCR); |
| SBL_PRINT_REGISTER(isp, SDR_REQ_EXP); |
| |
| dev_dbg(isp->dev, "--------------------------------------------\n"); |
| } |
| |
| #ifdef CONFIG_PM |
| |
| /* |
| * Power management support. |
| * |
| * As the ISP can't properly handle an input video stream interruption on a non |
| * frame boundary, the ISP pipelines need to be stopped before sensors get |
| * suspended. However, as suspending the sensors can require a running clock, |
| * which can be provided by the ISP, the ISP can't be completely suspended |
| * before the sensor. |
| * |
| * To solve this problem power management support is split into prepare/complete |
| * and suspend/resume operations. The pipelines are stopped in prepare() and the |
| * ISP clocks get disabled in suspend(). Similarly, the clocks are re-enabled in |
| * resume(), and the the pipelines are restarted in complete(). |
| * |
| * TODO: PM dependencies between the ISP and sensors are not modelled explicitly |
| * yet. |
| */ |
| static int isp_pm_prepare(struct device *dev) |
| { |
| struct isp_device *isp = dev_get_drvdata(dev); |
| int reset; |
| |
| WARN_ON(mutex_is_locked(&isp->isp_mutex)); |
| |
| if (isp->ref_count == 0) |
| return 0; |
| |
| reset = isp_suspend_modules(isp); |
| isp_disable_interrupts(isp); |
| isp_save_ctx(isp); |
| if (reset) |
| isp_reset(isp); |
| |
| return 0; |
| } |
| |
| static int isp_pm_suspend(struct device *dev) |
| { |
| struct isp_device *isp = dev_get_drvdata(dev); |
| |
| WARN_ON(mutex_is_locked(&isp->isp_mutex)); |
| |
| if (isp->ref_count) |
| isp_disable_clocks(isp); |
| |
| return 0; |
| } |
| |
| static int isp_pm_resume(struct device *dev) |
| { |
| struct isp_device *isp = dev_get_drvdata(dev); |
| |
| if (isp->ref_count == 0) |
| return 0; |
| |
| return isp_enable_clocks(isp); |
| } |
| |
| static void isp_pm_complete(struct device *dev) |
| { |
| struct isp_device *isp = dev_get_drvdata(dev); |
| |
| if (isp->ref_count == 0) |
| return; |
| |
| isp_restore_ctx(isp); |
| isp_enable_interrupts(isp); |
| isp_resume_modules(isp); |
| } |
| |
| #else |
| |
| #define isp_pm_prepare NULL |
| #define isp_pm_suspend NULL |
| #define isp_pm_resume NULL |
| #define isp_pm_complete NULL |
| |
| #endif /* CONFIG_PM */ |
| |
| static void isp_unregister_entities(struct isp_device *isp) |
| { |
| media_device_unregister(&isp->media_dev); |
| |
| omap3isp_csi2_unregister_entities(&isp->isp_csi2a); |
| omap3isp_ccp2_unregister_entities(&isp->isp_ccp2); |
| omap3isp_ccdc_unregister_entities(&isp->isp_ccdc); |
| omap3isp_preview_unregister_entities(&isp->isp_prev); |
| omap3isp_resizer_unregister_entities(&isp->isp_res); |
| omap3isp_stat_unregister_entities(&isp->isp_aewb); |
| omap3isp_stat_unregister_entities(&isp->isp_af); |
| omap3isp_stat_unregister_entities(&isp->isp_hist); |
| |
| v4l2_device_unregister(&isp->v4l2_dev); |
| media_device_cleanup(&isp->media_dev); |
| } |
| |
| static int isp_link_entity( |
| struct isp_device *isp, struct media_entity *entity, |
| enum isp_interface_type interface) |
| { |
| struct media_entity *input; |
| unsigned int flags; |
| unsigned int pad; |
| unsigned int i; |
| |
| /* Connect the sensor to the correct interface module. |
| * Parallel sensors are connected directly to the CCDC, while |
| * serial sensors are connected to the CSI2a, CCP2b or CSI2c |
| * receiver through CSIPHY1 or CSIPHY2. |
| */ |
| switch (interface) { |
| case ISP_INTERFACE_PARALLEL: |
| input = &isp->isp_ccdc.subdev.entity; |
| pad = CCDC_PAD_SINK; |
| flags = 0; |
| break; |
| |
| case ISP_INTERFACE_CSI2A_PHY2: |
| input = &isp->isp_csi2a.subdev.entity; |
| pad = CSI2_PAD_SINK; |
| flags = MEDIA_LNK_FL_IMMUTABLE | MEDIA_LNK_FL_ENABLED; |
| break; |
| |
| case ISP_INTERFACE_CCP2B_PHY1: |
| case ISP_INTERFACE_CCP2B_PHY2: |
| input = &isp->isp_ccp2.subdev.entity; |
| pad = CCP2_PAD_SINK; |
| flags = 0; |
| break; |
| |
| case ISP_INTERFACE_CSI2C_PHY1: |
| input = &isp->isp_csi2c.subdev.entity; |
| pad = CSI2_PAD_SINK; |
| flags = MEDIA_LNK_FL_IMMUTABLE | MEDIA_LNK_FL_ENABLED; |
| break; |
| |
| default: |
| dev_err(isp->dev, "%s: invalid interface type %u\n", __func__, |
| interface); |
| return -EINVAL; |
| } |
| |
| /* |
| * Not all interfaces are available on all revisions of the |
| * ISP. The sub-devices of those interfaces aren't initialised |
| * in such a case. Check this by ensuring the num_pads is |
| * non-zero. |
| */ |
| if (!input->num_pads) { |
| dev_err(isp->dev, "%s: invalid input %u\n", entity->name, |
| interface); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < entity->num_pads; i++) { |
| if (entity->pads[i].flags & MEDIA_PAD_FL_SOURCE) |
| break; |
| } |
| if (i == entity->num_pads) { |
| dev_err(isp->dev, "%s: no source pad in external entity %s\n", |
| __func__, entity->name); |
| return -EINVAL; |
| } |
| |
| return media_create_pad_link(entity, i, input, pad, flags); |
| } |
| |
| static int isp_register_entities(struct isp_device *isp) |
| { |
| int ret; |
| |
| isp->media_dev.dev = isp->dev; |
| strscpy(isp->media_dev.model, "TI OMAP3 ISP", |
| sizeof(isp->media_dev.model)); |
| isp->media_dev.hw_revision = isp->revision; |
| isp->media_dev.ops = &isp_media_ops; |
| media_device_init(&isp->media_dev); |
| |
| isp->v4l2_dev.mdev = &isp->media_dev; |
| ret = v4l2_device_register(isp->dev, &isp->v4l2_dev); |
| if (ret < 0) { |
| dev_err(isp->dev, "%s: V4L2 device registration failed (%d)\n", |
| __func__, ret); |
| goto done; |
| } |
| |
| /* Register internal entities */ |
| ret = omap3isp_ccp2_register_entities(&isp->isp_ccp2, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_csi2_register_entities(&isp->isp_csi2a, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_ccdc_register_entities(&isp->isp_ccdc, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_preview_register_entities(&isp->isp_prev, |
| &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_resizer_register_entities(&isp->isp_res, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_stat_register_entities(&isp->isp_aewb, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_stat_register_entities(&isp->isp_af, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| ret = omap3isp_stat_register_entities(&isp->isp_hist, &isp->v4l2_dev); |
| if (ret < 0) |
| goto done; |
| |
| done: |
| if (ret < 0) |
| isp_unregister_entities(isp); |
| |
| return ret; |
| } |
| |
| /* |
| * isp_create_links() - Create links for internal and external ISP entities |
| * @isp : Pointer to ISP device |
| * |
| * This function creates all links between ISP internal and external entities. |
| * |
| * Return: A negative error code on failure or zero on success. Possible error |
| * codes are those returned by media_create_pad_link(). |
| */ |
| static int isp_create_links(struct isp_device *isp) |
| { |
| int ret; |
| |
| /* Create links between entities and video nodes. */ |
| ret = media_create_pad_link( |
| &isp->isp_csi2a.subdev.entity, CSI2_PAD_SOURCE, |
| &isp->isp_csi2a.video_out.video.entity, 0, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccp2.video_in.video.entity, 0, |
| &isp->isp_ccp2.subdev.entity, CCP2_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_OF, |
| &isp->isp_ccdc.video_out.video.entity, 0, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_prev.video_in.video.entity, 0, |
| &isp->isp_prev.subdev.entity, PREV_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_prev.subdev.entity, PREV_PAD_SOURCE, |
| &isp->isp_prev.video_out.video.entity, 0, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_res.video_in.video.entity, 0, |
| &isp->isp_res.subdev.entity, RESZ_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_res.subdev.entity, RESZ_PAD_SOURCE, |
| &isp->isp_res.video_out.video.entity, 0, 0); |
| |
| if (ret < 0) |
| return ret; |
| |
| /* Create links between entities. */ |
| ret = media_create_pad_link( |
| &isp->isp_csi2a.subdev.entity, CSI2_PAD_SOURCE, |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccp2.subdev.entity, CCP2_PAD_SOURCE, |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_VP, |
| &isp->isp_prev.subdev.entity, PREV_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_OF, |
| &isp->isp_res.subdev.entity, RESZ_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_prev.subdev.entity, PREV_PAD_SOURCE, |
| &isp->isp_res.subdev.entity, RESZ_PAD_SINK, 0); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_VP, |
| &isp->isp_aewb.subdev.entity, 0, |
| MEDIA_LNK_FL_ENABLED | MEDIA_LNK_FL_IMMUTABLE); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_VP, |
| &isp->isp_af.subdev.entity, 0, |
| MEDIA_LNK_FL_ENABLED | MEDIA_LNK_FL_IMMUTABLE); |
| if (ret < 0) |
| return ret; |
| |
| ret = media_create_pad_link( |
| &isp->isp_ccdc.subdev.entity, CCDC_PAD_SOURCE_VP, |
| &isp->isp_hist.subdev.entity, 0, |
| MEDIA_LNK_FL_ENABLED | MEDIA_LNK_FL_IMMUTABLE); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static void isp_cleanup_modules(struct isp_device *isp) |
| { |
| omap3isp_h3a_aewb_cleanup(isp); |
| omap3isp_h3a_af_cleanup(isp); |
| omap3isp_hist_cleanup(isp); |
| omap3isp_resizer_cleanup(isp); |
| omap3isp_preview_cleanup(isp); |
| omap3isp_ccdc_cleanup(isp); |
| omap3isp_ccp2_cleanup(isp); |
| omap3isp_csi2_cleanup(isp); |
| omap3isp_csiphy_cleanup(isp); |
| } |
| |
| static int isp_initialize_modules(struct isp_device *isp) |
| { |
| int ret; |
| |
| ret = omap3isp_csiphy_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "CSI PHY initialization failed\n"); |
| return ret; |
| } |
| |
| ret = omap3isp_csi2_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "CSI2 initialization failed\n"); |
| goto error_csi2; |
| } |
| |
| ret = omap3isp_ccp2_init(isp); |
| if (ret < 0) { |
| if (ret != -EPROBE_DEFER) |
| dev_err(isp->dev, "CCP2 initialization failed\n"); |
| goto error_ccp2; |
| } |
| |
| ret = omap3isp_ccdc_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "CCDC initialization failed\n"); |
| goto error_ccdc; |
| } |
| |
| ret = omap3isp_preview_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "Preview initialization failed\n"); |
| goto error_preview; |
| } |
| |
| ret = omap3isp_resizer_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "Resizer initialization failed\n"); |
| goto error_resizer; |
| } |
| |
| ret = omap3isp_hist_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "Histogram initialization failed\n"); |
| goto error_hist; |
| } |
| |
| ret = omap3isp_h3a_aewb_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "H3A AEWB initialization failed\n"); |
| goto error_h3a_aewb; |
| } |
| |
| ret = omap3isp_h3a_af_init(isp); |
| if (ret < 0) { |
| dev_err(isp->dev, "H3A AF initialization failed\n"); |
| goto error_h3a_af; |
| } |
| |
| return 0; |
| |
| error_h3a_af: |
| omap3isp_h3a_aewb_cleanup(isp); |
| error_h3a_aewb: |
| omap3isp_hist_cleanup(isp); |
| error_hist: |
| omap3isp_resizer_cleanup(isp); |
| error_resizer: |
| omap3isp_preview_cleanup(isp); |
| error_preview: |
| omap3isp_ccdc_cleanup(isp); |
| error_ccdc: |
| omap3isp_ccp2_cleanup(isp); |
| error_ccp2: |
| omap3isp_csi2_cleanup(isp); |
| error_csi2: |
| omap3isp_csiphy_cleanup(isp); |
| |
| return ret; |
| } |
| |
| static void isp_detach_iommu(struct isp_device *isp) |
| { |
| #ifdef CONFIG_ARM_DMA_USE_IOMMU |
| arm_iommu_detach_device(isp->dev); |
| arm_iommu_release_mapping(isp->mapping); |
| isp->mapping = NULL; |
| #endif |
| } |
| |
| static int isp_attach_iommu(struct isp_device *isp) |
| { |
| #ifdef CONFIG_ARM_DMA_USE_IOMMU |
| struct dma_iommu_mapping *mapping; |
| int ret; |
| |
| /* |
| * Create the ARM mapping, used by the ARM DMA mapping core to allocate |
| * VAs. This will allocate a corresponding IOMMU domain. |
| */ |
| mapping = arm_iommu_create_mapping(&platform_bus_type, SZ_1G, SZ_2G); |
| if (IS_ERR(mapping)) { |
| dev_err(isp->dev, "failed to create ARM IOMMU mapping\n"); |
| return PTR_ERR(mapping); |
| } |
| |
| isp->mapping = mapping; |
| |
| /* Attach the ARM VA mapping to the device. */ |
| ret = arm_iommu_attach_device(isp->dev, mapping); |
| if (ret < 0) { |
| dev_err(isp->dev, "failed to attach device to VA mapping\n"); |
| goto error; |
| } |
| |
| return 0; |
| |
| error: |
| arm_iommu_release_mapping(isp->mapping); |
| isp->mapping = NULL; |
| return ret; |
| #else |
| return -ENODEV; |
| #endif |
| } |
| |
| /* |
| * isp_remove - Remove ISP platform device |
| * @pdev: Pointer to ISP platform device |
| * |
| * Always returns 0. |
| */ |
| static int isp_remove(struct platform_device *pdev) |
| { |
| struct isp_device *isp = platform_get_drvdata(pdev); |
| |
| v4l2_async_nf_unregister(&isp->notifier); |
| isp_unregister_entities(isp); |
| isp_cleanup_modules(isp); |
| isp_xclk_cleanup(isp); |
| |
| __omap3isp_get(isp, false); |
| isp_detach_iommu(isp); |
| __omap3isp_put(isp, false); |
| |
| media_entity_enum_cleanup(&isp->crashed); |
| v4l2_async_nf_cleanup(&isp->notifier); |
| |
| kfree(isp); |
| |
| return 0; |
| } |
| |
| enum isp_of_phy { |
| ISP_OF_PHY_PARALLEL = 0, |
| ISP_OF_PHY_CSIPHY1, |
| ISP_OF_PHY_CSIPHY2, |
| }; |
| |
| static int isp_subdev_notifier_complete(struct v4l2_async_notifier *async) |
| { |
| struct isp_device *isp = container_of(async, struct isp_device, |
| notifier); |
| struct v4l2_device *v4l2_dev = &isp->v4l2_dev; |
| struct v4l2_subdev *sd; |
| int ret; |
| |
| mutex_lock(&isp->media_dev.graph_mutex); |
| |
| ret = media_entity_enum_init(&isp->crashed, &isp->media_dev); |
| if (ret) { |
| mutex_unlock(&isp->media_dev.graph_mutex); |
| return ret; |
| } |
| |
| list_for_each_entry(sd, &v4l2_dev->subdevs, list) { |
| if (sd->notifier != &isp->notifier) |
| continue; |
| |
| ret = isp_link_entity(isp, &sd->entity, |
| v4l2_subdev_to_bus_cfg(sd)->interface); |
| if (ret < 0) { |
| mutex_unlock(&isp->media_dev.graph_mutex); |
| return ret; |
| } |
| } |
| |
| mutex_unlock(&isp->media_dev.graph_mutex); |
| |
| ret = v4l2_device_register_subdev_nodes(&isp->v4l2_dev); |
| if (ret < 0) |
| return ret; |
| |
| return media_device_register(&isp->media_dev); |
| } |
| |
| static void isp_parse_of_parallel_endpoint(struct device *dev, |
| struct v4l2_fwnode_endpoint *vep, |
| struct isp_bus_cfg *buscfg) |
| { |
| buscfg->interface = ISP_INTERFACE_PARALLEL; |
| buscfg->bus.parallel.data_lane_shift = vep->bus.parallel.data_shift; |
| buscfg->bus.parallel.clk_pol = |
| !!(vep->bus.parallel.flags & V4L2_MBUS_PCLK_SAMPLE_FALLING); |
| buscfg->bus.parallel.hs_pol = |
| !!(vep->bus.parallel.flags & V4L2_MBUS_VSYNC_ACTIVE_LOW); |
| buscfg->bus.parallel.vs_pol = |
| !!(vep->bus.parallel.flags & V4L2_MBUS_HSYNC_ACTIVE_LOW); |
| buscfg->bus.parallel.fld_pol = |
| !!(vep->bus.parallel.flags & V4L2_MBUS_FIELD_EVEN_LOW); |
| buscfg->bus.parallel.data_pol = |
| !!(vep->bus.parallel.flags & V4L2_MBUS_DATA_ACTIVE_LOW); |
| buscfg->bus.parallel.bt656 = vep->bus_type == V4L2_MBUS_BT656; |
| } |
| |
| static void isp_parse_of_csi2_endpoint(struct device *dev, |
| struct v4l2_fwnode_endpoint *vep, |
| struct isp_bus_cfg *buscfg) |
| { |
| unsigned int i; |
| |
| buscfg->bus.csi2.lanecfg.clk.pos = vep->bus.mipi_csi2.clock_lane; |
| buscfg->bus.csi2.lanecfg.clk.pol = |
| vep->bus.mipi_csi2.lane_polarities[0]; |
| dev_dbg(dev, "clock lane polarity %u, pos %u\n", |
| buscfg->bus.csi2.lanecfg.clk.pol, |
| buscfg->bus.csi2.lanecfg.clk.pos); |
| |
| buscfg->bus.csi2.num_data_lanes = vep->bus.mipi_csi2.num_data_lanes; |
| |
| for (i = 0; i < buscfg->bus.csi2.num_data_lanes; i++) { |
| buscfg->bus.csi2.lanecfg.data[i].pos = |
| vep->bus.mipi_csi2.data_lanes[i]; |
| buscfg->bus.csi2.lanecfg.data[i].pol = |
| vep->bus.mipi_csi2.lane_polarities[i + 1]; |
| dev_dbg(dev, |
| "data lane %u polarity %u, pos %u\n", i, |
| buscfg->bus.csi2.lanecfg.data[i].pol, |
| buscfg->bus.csi2.lanecfg.data[i].pos); |
| } |
| /* |
| * FIXME: now we assume the CRC is always there. Implement a way to |
| * obtain this information from the sensor. Frame descriptors, perhaps? |
| */ |
| buscfg->bus.csi2.crc = 1; |
| } |
| |
| static void isp_parse_of_csi1_endpoint(struct device *dev, |
| struct v4l2_fwnode_endpoint *vep, |
| struct isp_bus_cfg *buscfg) |
| { |
| buscfg->bus.ccp2.lanecfg.clk.pos = vep->bus.mipi_csi1.clock_lane; |
| buscfg->bus.ccp2.lanecfg.clk.pol = vep->bus.mipi_csi1.lane_polarity[0]; |
| dev_dbg(dev, "clock lane polarity %u, pos %u\n", |
| buscfg->bus.ccp2.lanecfg.clk.pol, |
| buscfg->bus.ccp2.lanecfg.clk.pos); |
| |
| buscfg->bus.ccp2.lanecfg.data[0].pos = vep->bus.mipi_csi1.data_lane; |
| buscfg->bus.ccp2.lanecfg.data[0].pol = |
| vep->bus.mipi_csi1.lane_polarity[1]; |
| |
| dev_dbg(dev, "data lane polarity %u, pos %u\n", |
| buscfg->bus.ccp2.lanecfg.data[0].pol, |
| buscfg->bus.ccp2.lanecfg.data[0].pos); |
| |
| buscfg->bus.ccp2.strobe_clk_pol = vep->bus.mipi_csi1.clock_inv; |
| buscfg->bus.ccp2.phy_layer = vep->bus.mipi_csi1.strobe; |
| buscfg->bus.ccp2.ccp2_mode = vep->bus_type == V4L2_MBUS_CCP2; |
| buscfg->bus.ccp2.vp_clk_pol = 1; |
| |
| buscfg->bus.ccp2.crc = 1; |
| } |
| |
| static struct { |
| u32 phy; |
| u32 csi2_if; |
| u32 csi1_if; |
| } isp_bus_interfaces[2] = { |
| { ISP_OF_PHY_CSIPHY1, |
| ISP_INTERFACE_CSI2C_PHY1, ISP_INTERFACE_CCP2B_PHY1 }, |
| { ISP_OF_PHY_CSIPHY2, |
| ISP_INTERFACE_CSI2A_PHY2, ISP_INTERFACE_CCP2B_PHY2 }, |
| }; |
| |
| static int isp_parse_of_endpoints(struct isp_device *isp) |
| { |
| struct fwnode_handle *ep; |
| struct isp_async_subdev *isd = NULL; |
| unsigned int i; |
| |
| ep = fwnode_graph_get_endpoint_by_id( |
| dev_fwnode(isp->dev), ISP_OF_PHY_PARALLEL, 0, |
| FWNODE_GRAPH_ENDPOINT_NEXT); |
| |
| if (ep) { |
| struct v4l2_fwnode_endpoint vep = { |
| .bus_type = V4L2_MBUS_PARALLEL |
| }; |
| int ret; |
| |
| dev_dbg(isp->dev, "parsing parallel interface\n"); |
| |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| |
| if (!ret) { |
| isd = v4l2_async_nf_add_fwnode_remote(&isp->notifier, |
| ep, struct |
| isp_async_subdev); |
| if (!IS_ERR(isd)) |
| isp_parse_of_parallel_endpoint(isp->dev, &vep, &isd->bus); |
| } |
| |
| fwnode_handle_put(ep); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(isp_bus_interfaces); i++) { |
| struct v4l2_fwnode_endpoint vep = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY |
| }; |
| int ret; |
| |
| ep = fwnode_graph_get_endpoint_by_id( |
| dev_fwnode(isp->dev), isp_bus_interfaces[i].phy, 0, |
| FWNODE_GRAPH_ENDPOINT_NEXT); |
| |
| if (!ep) |
| continue; |
| |
| dev_dbg(isp->dev, "parsing serial interface %u, node %pOF\n", i, |
| to_of_node(ep)); |
| |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| if (ret == -ENXIO) { |
| vep = (struct v4l2_fwnode_endpoint) |
| { .bus_type = V4L2_MBUS_CSI1 }; |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| |
| if (ret == -ENXIO) { |
| vep = (struct v4l2_fwnode_endpoint) |
| { .bus_type = V4L2_MBUS_CCP2 }; |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| } |
| } |
| |
| if (!ret) { |
| isd = v4l2_async_nf_add_fwnode_remote(&isp->notifier, |
| ep, |
| struct |
| isp_async_subdev); |
| |
| if (!IS_ERR(isd)) { |
| switch (vep.bus_type) { |
| case V4L2_MBUS_CSI2_DPHY: |
| isd->bus.interface = |
| isp_bus_interfaces[i].csi2_if; |
| isp_parse_of_csi2_endpoint(isp->dev, &vep, &isd->bus); |
| break; |
| case V4L2_MBUS_CSI1: |
| case V4L2_MBUS_CCP2: |
| isd->bus.interface = |
| isp_bus_interfaces[i].csi1_if; |
| isp_parse_of_csi1_endpoint(isp->dev, &vep, |
| &isd->bus); |
| break; |
| default: |
| break; |
| } |
| } |
| } |
| |
| fwnode_handle_put(ep); |
| } |
| |
| return 0; |
| } |
| |
| static const struct v4l2_async_notifier_operations isp_subdev_notifier_ops = { |
| .complete = isp_subdev_notifier_complete, |
| }; |
| |
| /* |
| * isp_probe - Probe ISP platform device |
| * @pdev: Pointer to ISP platform device |
| * |
| * Returns 0 if successful, |
| * -ENOMEM if no memory available, |
| * -ENODEV if no platform device resources found |
| * or no space for remapping registers, |
| * -EINVAL if couldn't install ISR, |
| * or clk_get return error value. |
| */ |
| static int isp_probe(struct platform_device *pdev) |
| { |
| struct isp_device *isp; |
| struct resource *mem; |
| int ret; |
| int i, m; |
| |
| isp = kzalloc(sizeof(*isp), GFP_KERNEL); |
| if (!isp) { |
| dev_err(&pdev->dev, "could not allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| ret = fwnode_property_read_u32(of_fwnode_handle(pdev->dev.of_node), |
| "ti,phy-type", &isp->phy_type); |
| if (ret) |
| goto error_release_isp; |
| |
| isp->syscon = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, |
| "syscon"); |
| if (IS_ERR(isp->syscon)) { |
| ret = PTR_ERR(isp->syscon); |
| goto error_release_isp; |
| } |
| |
| ret = of_property_read_u32_index(pdev->dev.of_node, |
| "syscon", 1, &isp->syscon_offset); |
| if (ret) |
| goto error_release_isp; |
| |
| isp->autoidle = autoidle; |
| |
| mutex_init(&isp->isp_mutex); |
| spin_lock_init(&isp->stat_lock); |
| v4l2_async_nf_init(&isp->notifier); |
| isp->dev = &pdev->dev; |
| |
| ret = isp_parse_of_endpoints(isp); |
| if (ret < 0) |
| goto error; |
| |
| isp->ref_count = 0; |
| |
| ret = dma_coerce_mask_and_coherent(isp->dev, DMA_BIT_MASK(32)); |
| if (ret) |
| goto error; |
| |
| platform_set_drvdata(pdev, isp); |
| |
| /* Regulators */ |
| isp->isp_csiphy1.vdd = devm_regulator_get(&pdev->dev, "vdd-csiphy1"); |
| isp->isp_csiphy2.vdd = devm_regulator_get(&pdev->dev, "vdd-csiphy2"); |
| |
| /* Clocks |
| * |
| * The ISP clock tree is revision-dependent. We thus need to enable ICLK |
| * manually to read the revision before calling __omap3isp_get(). |
| * |
| * Start by mapping the ISP MMIO area, which is in two pieces. |
| * The ISP IOMMU is in between. Map both now, and fill in the |
| * ISP revision specific portions a little later in the |
| * function. |
| */ |
| for (i = 0; i < 2; i++) { |
| unsigned int map_idx = i ? OMAP3_ISP_IOMEM_CSI2A_REGS1 : 0; |
| |
| mem = platform_get_resource(pdev, IORESOURCE_MEM, i); |
| isp->mmio_base[map_idx] = |
| devm_ioremap_resource(isp->dev, mem); |
| if (IS_ERR(isp->mmio_base[map_idx])) { |
| ret = PTR_ERR(isp->mmio_base[map_idx]); |
| goto error; |
| } |
| } |
| |
| ret = isp_get_clocks(isp); |
| if (ret < 0) |
| goto error; |
| |
| ret = clk_enable(isp->clock[ISP_CLK_CAM_ICK]); |
| if (ret < 0) |
| goto error; |
| |
| isp->revision = isp_reg_readl(isp, OMAP3_ISP_IOMEM_MAIN, ISP_REVISION); |
| dev_info(isp->dev, "Revision %d.%d found\n", |
| (isp->revision & 0xf0) >> 4, isp->revision & 0x0f); |
| |
| clk_disable(isp->clock[ISP_CLK_CAM_ICK]); |
| |
| if (__omap3isp_get(isp, false) == NULL) { |
| ret = -ENODEV; |
| goto error; |
| } |
| |
| ret = isp_reset(isp); |
| if (ret < 0) |
| goto error_isp; |
| |
| ret = isp_xclk_init(isp); |
| if (ret < 0) |
| goto error_isp; |
| |
| /* Memory resources */ |
| for (m = 0; m < ARRAY_SIZE(isp_res_maps); m++) |
| if (isp->revision == isp_res_maps[m].isp_rev) |
| break; |
| |
| if (m == ARRAY_SIZE(isp_res_maps)) { |
| dev_err(isp->dev, "No resource map found for ISP rev %d.%d\n", |
| (isp->revision & 0xf0) >> 4, isp->revision & 0xf); |
| ret = -ENODEV; |
| goto error_isp; |
| } |
| |
| for (i = 1; i < OMAP3_ISP_IOMEM_CSI2A_REGS1; i++) |
| isp->mmio_base[i] = |
| isp->mmio_base[0] + isp_res_maps[m].offset[i]; |
| |
| for (i = OMAP3_ISP_IOMEM_CSIPHY2; i < OMAP3_ISP_IOMEM_LAST; i++) |
| isp->mmio_base[i] = |
| isp->mmio_base[OMAP3_ISP_IOMEM_CSI2A_REGS1] |
| + isp_res_maps[m].offset[i]; |
| |
| isp->mmio_hist_base_phys = |
| mem->start + isp_res_maps[m].offset[OMAP3_ISP_IOMEM_HIST]; |
| |
| /* IOMMU */ |
| ret = isp_attach_iommu(isp); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "unable to attach to IOMMU\n"); |
| goto error_isp; |
| } |
| |
| /* Interrupt */ |
| ret = platform_get_irq(pdev, 0); |
| if (ret <= 0) { |
| ret = -ENODEV; |
| goto error_iommu; |
| } |
| isp->irq_num = ret; |
| |
| if (devm_request_irq(isp->dev, isp->irq_num, isp_isr, IRQF_SHARED, |
| "OMAP3 ISP", isp)) { |
| dev_err(isp->dev, "Unable to request IRQ\n"); |
| ret = -EINVAL; |
| goto error_iommu; |
| } |
| |
| /* Entities */ |
| ret = isp_initialize_modules(isp); |
| if (ret < 0) |
| goto error_iommu; |
| |
| ret = isp_register_entities(isp); |
| if (ret < 0) |
| goto error_modules; |
| |
| ret = isp_create_links(isp); |
| if (ret < 0) |
| goto error_register_entities; |
| |
| isp->notifier.ops = &isp_subdev_notifier_ops; |
| |
| ret = v4l2_async_nf_register(&isp->v4l2_dev, &isp->notifier); |
| if (ret) |
| goto error_register_entities; |
| |
| isp_core_init(isp, 1); |
| omap3isp_put(isp); |
| |
| return 0; |
| |
| error_register_entities: |
| isp_unregister_entities(isp); |
| error_modules: |
| isp_cleanup_modules(isp); |
| error_iommu: |
| isp_detach_iommu(isp); |
| error_isp: |
| isp_xclk_cleanup(isp); |
| __omap3isp_put(isp, false); |
| error: |
| v4l2_async_nf_cleanup(&isp->notifier); |
| mutex_destroy(&isp->isp_mutex); |
| error_release_isp: |
| kfree(isp); |
| |
| return ret; |
| } |
| |
| static const struct dev_pm_ops omap3isp_pm_ops = { |
| .prepare = isp_pm_prepare, |
| .suspend = isp_pm_suspend, |
| .resume = isp_pm_resume, |
| .complete = isp_pm_complete, |
| }; |
| |
| static const struct platform_device_id omap3isp_id_table[] = { |
| { "omap3isp", 0 }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(platform, omap3isp_id_table); |
| |
| static const struct of_device_id omap3isp_of_table[] = { |
| { .compatible = "ti,omap3-isp" }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, omap3isp_of_table); |
| |
| static struct platform_driver omap3isp_driver = { |
| .probe = isp_probe, |
| .remove = isp_remove, |
| .id_table = omap3isp_id_table, |
| .driver = { |
| .name = "omap3isp", |
| .pm = &omap3isp_pm_ops, |
| .of_match_table = omap3isp_of_table, |
| }, |
| }; |
| |
| module_platform_driver(omap3isp_driver); |
| |
| MODULE_AUTHOR("Nokia Corporation"); |
| MODULE_DESCRIPTION("TI OMAP3 ISP driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_VERSION(ISP_VIDEO_DRIVER_VERSION); |