| /* |
| * isphist.c |
| * |
| * TI OMAP3 ISP - Histogram module |
| * |
| * Copyright (C) 2010 Nokia Corporation |
| * Copyright (C) 2009 Texas Instruments, Inc. |
| * |
| * Contacts: David Cohen <dacohen@gmail.com> |
| * Laurent Pinchart <laurent.pinchart@ideasonboard.com> |
| * Sakari Ailus <sakari.ailus@iki.fi> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/slab.h> |
| #include <linux/uaccess.h> |
| #include <linux/device.h> |
| |
| #include "isp.h" |
| #include "ispreg.h" |
| #include "isphist.h" |
| |
| #define OMAP24XX_DMA_NO_DEVICE 0 |
| |
| #define HIST_CONFIG_DMA 1 |
| |
| #define HIST_USING_DMA(hist) ((hist)->dma_ch >= 0) |
| |
| /* |
| * hist_reset_mem - clear Histogram memory before start stats engine. |
| */ |
| static void hist_reset_mem(struct ispstat *hist) |
| { |
| struct isp_device *isp = hist->isp; |
| struct omap3isp_hist_config *conf = hist->priv; |
| unsigned int i; |
| |
| isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR); |
| |
| /* |
| * By setting it, the histogram internal buffer is being cleared at the |
| * same time it's being read. This bit must be cleared afterwards. |
| */ |
| isp_reg_set(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR); |
| |
| /* |
| * We'll clear 4 words at each iteration for optimization. It avoids |
| * 3/4 of the jumps. We also know HIST_MEM_SIZE is divisible by 4. |
| */ |
| for (i = OMAP3ISP_HIST_MEM_SIZE / 4; i > 0; i--) { |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| } |
| isp_reg_clr(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR); |
| |
| hist->wait_acc_frames = conf->num_acc_frames; |
| } |
| |
| static void hist_dma_config(struct ispstat *hist) |
| { |
| struct isp_device *isp = hist->isp; |
| |
| hist->dma_config.data_type = OMAP_DMA_DATA_TYPE_S32; |
| hist->dma_config.sync_mode = OMAP_DMA_SYNC_ELEMENT; |
| hist->dma_config.frame_count = 1; |
| hist->dma_config.src_amode = OMAP_DMA_AMODE_CONSTANT; |
| hist->dma_config.src_start = isp->mmio_base_phys[OMAP3_ISP_IOMEM_HIST] |
| + ISPHIST_DATA; |
| hist->dma_config.dst_amode = OMAP_DMA_AMODE_POST_INC; |
| hist->dma_config.src_or_dst_synch = OMAP_DMA_SRC_SYNC; |
| } |
| |
| /* |
| * hist_setup_regs - Helper function to update Histogram registers. |
| */ |
| static void hist_setup_regs(struct ispstat *hist, void *priv) |
| { |
| struct isp_device *isp = hist->isp; |
| struct omap3isp_hist_config *conf = priv; |
| int c; |
| u32 cnt; |
| u32 wb_gain; |
| u32 reg_hor[OMAP3ISP_HIST_MAX_REGIONS]; |
| u32 reg_ver[OMAP3ISP_HIST_MAX_REGIONS]; |
| |
| if (!hist->update || hist->state == ISPSTAT_DISABLED || |
| hist->state == ISPSTAT_DISABLING) |
| return; |
| |
| cnt = conf->cfa << ISPHIST_CNT_CFA_SHIFT; |
| |
| wb_gain = conf->wg[0] << ISPHIST_WB_GAIN_WG00_SHIFT; |
| wb_gain |= conf->wg[1] << ISPHIST_WB_GAIN_WG01_SHIFT; |
| wb_gain |= conf->wg[2] << ISPHIST_WB_GAIN_WG02_SHIFT; |
| if (conf->cfa == OMAP3ISP_HIST_CFA_BAYER) |
| wb_gain |= conf->wg[3] << ISPHIST_WB_GAIN_WG03_SHIFT; |
| |
| /* Regions size and position */ |
| for (c = 0; c < OMAP3ISP_HIST_MAX_REGIONS; c++) { |
| if (c < conf->num_regions) { |
| reg_hor[c] = (conf->region[c].h_start << |
| ISPHIST_REG_START_SHIFT) |
| | (conf->region[c].h_end << |
| ISPHIST_REG_END_SHIFT); |
| reg_ver[c] = (conf->region[c].v_start << |
| ISPHIST_REG_START_SHIFT) |
| | (conf->region[c].v_end << |
| ISPHIST_REG_END_SHIFT); |
| } else { |
| reg_hor[c] = 0; |
| reg_ver[c] = 0; |
| } |
| } |
| |
| cnt |= conf->hist_bins << ISPHIST_CNT_BINS_SHIFT; |
| switch (conf->hist_bins) { |
| case OMAP3ISP_HIST_BINS_256: |
| cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 8) << |
| ISPHIST_CNT_SHIFT_SHIFT; |
| break; |
| case OMAP3ISP_HIST_BINS_128: |
| cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 7) << |
| ISPHIST_CNT_SHIFT_SHIFT; |
| break; |
| case OMAP3ISP_HIST_BINS_64: |
| cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 6) << |
| ISPHIST_CNT_SHIFT_SHIFT; |
| break; |
| default: /* OMAP3ISP_HIST_BINS_32 */ |
| cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 5) << |
| ISPHIST_CNT_SHIFT_SHIFT; |
| break; |
| } |
| |
| hist_reset_mem(hist); |
| |
| isp_reg_writel(isp, cnt, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT); |
| isp_reg_writel(isp, wb_gain, OMAP3_ISP_IOMEM_HIST, ISPHIST_WB_GAIN); |
| isp_reg_writel(isp, reg_hor[0], OMAP3_ISP_IOMEM_HIST, ISPHIST_R0_HORZ); |
| isp_reg_writel(isp, reg_ver[0], OMAP3_ISP_IOMEM_HIST, ISPHIST_R0_VERT); |
| isp_reg_writel(isp, reg_hor[1], OMAP3_ISP_IOMEM_HIST, ISPHIST_R1_HORZ); |
| isp_reg_writel(isp, reg_ver[1], OMAP3_ISP_IOMEM_HIST, ISPHIST_R1_VERT); |
| isp_reg_writel(isp, reg_hor[2], OMAP3_ISP_IOMEM_HIST, ISPHIST_R2_HORZ); |
| isp_reg_writel(isp, reg_ver[2], OMAP3_ISP_IOMEM_HIST, ISPHIST_R2_VERT); |
| isp_reg_writel(isp, reg_hor[3], OMAP3_ISP_IOMEM_HIST, ISPHIST_R3_HORZ); |
| isp_reg_writel(isp, reg_ver[3], OMAP3_ISP_IOMEM_HIST, ISPHIST_R3_VERT); |
| |
| hist->update = 0; |
| hist->config_counter += hist->inc_config; |
| hist->inc_config = 0; |
| hist->buf_size = conf->buf_size; |
| } |
| |
| static void hist_enable(struct ispstat *hist, int enable) |
| { |
| if (enable) { |
| isp_reg_set(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR, |
| ISPHIST_PCR_ENABLE); |
| omap3isp_subclk_enable(hist->isp, OMAP3_ISP_SUBCLK_HIST); |
| } else { |
| isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR, |
| ISPHIST_PCR_ENABLE); |
| omap3isp_subclk_disable(hist->isp, OMAP3_ISP_SUBCLK_HIST); |
| } |
| } |
| |
| static int hist_busy(struct ispstat *hist) |
| { |
| return isp_reg_readl(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR) |
| & ISPHIST_PCR_BUSY; |
| } |
| |
| static void hist_dma_cb(int lch, u16 ch_status, void *data) |
| { |
| struct ispstat *hist = data; |
| |
| if (ch_status & ~OMAP_DMA_BLOCK_IRQ) { |
| dev_dbg(hist->isp->dev, "hist: DMA error. status = 0x%04x\n", |
| ch_status); |
| omap_stop_dma(lch); |
| hist_reset_mem(hist); |
| atomic_set(&hist->buf_err, 1); |
| } |
| isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, |
| ISPHIST_CNT_CLEAR); |
| |
| omap3isp_stat_dma_isr(hist); |
| if (hist->state != ISPSTAT_DISABLED) |
| omap3isp_hist_dma_done(hist->isp); |
| } |
| |
| static int hist_buf_dma(struct ispstat *hist) |
| { |
| dma_addr_t dma_addr = hist->active_buf->dma_addr; |
| |
| if (unlikely(!dma_addr)) { |
| dev_dbg(hist->isp->dev, "hist: invalid DMA buffer address\n"); |
| hist_reset_mem(hist); |
| return STAT_NO_BUF; |
| } |
| |
| isp_reg_writel(hist->isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR); |
| isp_reg_set(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, |
| ISPHIST_CNT_CLEAR); |
| omap3isp_flush(hist->isp); |
| hist->dma_config.dst_start = dma_addr; |
| hist->dma_config.elem_count = hist->buf_size / sizeof(u32); |
| omap_set_dma_params(hist->dma_ch, &hist->dma_config); |
| |
| omap_start_dma(hist->dma_ch); |
| |
| return STAT_BUF_WAITING_DMA; |
| } |
| |
| static int hist_buf_pio(struct ispstat *hist) |
| { |
| struct isp_device *isp = hist->isp; |
| u32 *buf = hist->active_buf->virt_addr; |
| unsigned int i; |
| |
| if (!buf) { |
| dev_dbg(isp->dev, "hist: invalid PIO buffer address\n"); |
| hist_reset_mem(hist); |
| return STAT_NO_BUF; |
| } |
| |
| isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR); |
| |
| /* |
| * By setting it, the histogram internal buffer is being cleared at the |
| * same time it's being read. This bit must be cleared just after all |
| * data is acquired. |
| */ |
| isp_reg_set(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR); |
| |
| /* |
| * We'll read 4 times a 4-bytes-word at each iteration for |
| * optimization. It avoids 3/4 of the jumps. We also know buf_size is |
| * divisible by 16. |
| */ |
| for (i = hist->buf_size / 16; i > 0; i--) { |
| *buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| *buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| *buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| *buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA); |
| } |
| isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, |
| ISPHIST_CNT_CLEAR); |
| |
| return STAT_BUF_DONE; |
| } |
| |
| /* |
| * hist_buf_process - Callback from ISP driver for HIST interrupt. |
| */ |
| static int hist_buf_process(struct ispstat *hist) |
| { |
| struct omap3isp_hist_config *user_cfg = hist->priv; |
| int ret; |
| |
| if (atomic_read(&hist->buf_err) || hist->state != ISPSTAT_ENABLED) { |
| hist_reset_mem(hist); |
| return STAT_NO_BUF; |
| } |
| |
| if (--(hist->wait_acc_frames)) |
| return STAT_NO_BUF; |
| |
| if (HIST_USING_DMA(hist)) |
| ret = hist_buf_dma(hist); |
| else |
| ret = hist_buf_pio(hist); |
| |
| hist->wait_acc_frames = user_cfg->num_acc_frames; |
| |
| return ret; |
| } |
| |
| static u32 hist_get_buf_size(struct omap3isp_hist_config *conf) |
| { |
| return OMAP3ISP_HIST_MEM_SIZE_BINS(conf->hist_bins) * conf->num_regions; |
| } |
| |
| /* |
| * hist_validate_params - Helper function to check user given params. |
| * @new_conf: Pointer to user configuration structure. |
| * |
| * Returns 0 on success configuration. |
| */ |
| static int hist_validate_params(struct ispstat *hist, void *new_conf) |
| { |
| struct omap3isp_hist_config *user_cfg = new_conf; |
| int c; |
| u32 buf_size; |
| |
| if (user_cfg->cfa > OMAP3ISP_HIST_CFA_FOVEONX3) |
| return -EINVAL; |
| |
| /* Regions size and position */ |
| |
| if ((user_cfg->num_regions < OMAP3ISP_HIST_MIN_REGIONS) || |
| (user_cfg->num_regions > OMAP3ISP_HIST_MAX_REGIONS)) |
| return -EINVAL; |
| |
| /* Regions */ |
| for (c = 0; c < user_cfg->num_regions; c++) { |
| if (user_cfg->region[c].h_start & ~ISPHIST_REG_START_END_MASK) |
| return -EINVAL; |
| if (user_cfg->region[c].h_end & ~ISPHIST_REG_START_END_MASK) |
| return -EINVAL; |
| if (user_cfg->region[c].v_start & ~ISPHIST_REG_START_END_MASK) |
| return -EINVAL; |
| if (user_cfg->region[c].v_end & ~ISPHIST_REG_START_END_MASK) |
| return -EINVAL; |
| if (user_cfg->region[c].h_start > user_cfg->region[c].h_end) |
| return -EINVAL; |
| if (user_cfg->region[c].v_start > user_cfg->region[c].v_end) |
| return -EINVAL; |
| } |
| |
| switch (user_cfg->num_regions) { |
| case 1: |
| if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_256) |
| return -EINVAL; |
| break; |
| case 2: |
| if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_128) |
| return -EINVAL; |
| break; |
| default: /* 3 or 4 */ |
| if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_64) |
| return -EINVAL; |
| break; |
| } |
| |
| buf_size = hist_get_buf_size(user_cfg); |
| if (buf_size > user_cfg->buf_size) |
| /* User's buf_size request wasn't enough */ |
| user_cfg->buf_size = buf_size; |
| else if (user_cfg->buf_size > OMAP3ISP_HIST_MAX_BUF_SIZE) |
| user_cfg->buf_size = OMAP3ISP_HIST_MAX_BUF_SIZE; |
| |
| return 0; |
| } |
| |
| static int hist_comp_params(struct ispstat *hist, |
| struct omap3isp_hist_config *user_cfg) |
| { |
| struct omap3isp_hist_config *cur_cfg = hist->priv; |
| int c; |
| |
| if (cur_cfg->cfa != user_cfg->cfa) |
| return 1; |
| |
| if (cur_cfg->num_acc_frames != user_cfg->num_acc_frames) |
| return 1; |
| |
| if (cur_cfg->hist_bins != user_cfg->hist_bins) |
| return 1; |
| |
| for (c = 0; c < OMAP3ISP_HIST_MAX_WG; c++) { |
| if (c == 3 && user_cfg->cfa == OMAP3ISP_HIST_CFA_FOVEONX3) |
| break; |
| else if (cur_cfg->wg[c] != user_cfg->wg[c]) |
| return 1; |
| } |
| |
| if (cur_cfg->num_regions != user_cfg->num_regions) |
| return 1; |
| |
| /* Regions */ |
| for (c = 0; c < user_cfg->num_regions; c++) { |
| if (cur_cfg->region[c].h_start != user_cfg->region[c].h_start) |
| return 1; |
| if (cur_cfg->region[c].h_end != user_cfg->region[c].h_end) |
| return 1; |
| if (cur_cfg->region[c].v_start != user_cfg->region[c].v_start) |
| return 1; |
| if (cur_cfg->region[c].v_end != user_cfg->region[c].v_end) |
| return 1; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * hist_update_params - Helper function to check and store user given params. |
| * @new_conf: Pointer to user configuration structure. |
| */ |
| static void hist_set_params(struct ispstat *hist, void *new_conf) |
| { |
| struct omap3isp_hist_config *user_cfg = new_conf; |
| struct omap3isp_hist_config *cur_cfg = hist->priv; |
| |
| if (!hist->configured || hist_comp_params(hist, user_cfg)) { |
| memcpy(cur_cfg, user_cfg, sizeof(*user_cfg)); |
| if (user_cfg->num_acc_frames == 0) |
| user_cfg->num_acc_frames = 1; |
| hist->inc_config++; |
| hist->update = 1; |
| /* |
| * User might be asked for a bigger buffer than necessary for |
| * this configuration. In order to return the right amount of |
| * data during buffer request, let's calculate the size here |
| * instead of stick with user_cfg->buf_size. |
| */ |
| cur_cfg->buf_size = hist_get_buf_size(cur_cfg); |
| |
| } |
| } |
| |
| static long hist_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg) |
| { |
| struct ispstat *stat = v4l2_get_subdevdata(sd); |
| |
| switch (cmd) { |
| case VIDIOC_OMAP3ISP_HIST_CFG: |
| return omap3isp_stat_config(stat, arg); |
| case VIDIOC_OMAP3ISP_STAT_REQ: |
| return omap3isp_stat_request_statistics(stat, arg); |
| case VIDIOC_OMAP3ISP_STAT_EN: { |
| int *en = arg; |
| return omap3isp_stat_enable(stat, !!*en); |
| } |
| } |
| |
| return -ENOIOCTLCMD; |
| |
| } |
| |
| static const struct ispstat_ops hist_ops = { |
| .validate_params = hist_validate_params, |
| .set_params = hist_set_params, |
| .setup_regs = hist_setup_regs, |
| .enable = hist_enable, |
| .busy = hist_busy, |
| .buf_process = hist_buf_process, |
| }; |
| |
| static const struct v4l2_subdev_core_ops hist_subdev_core_ops = { |
| .ioctl = hist_ioctl, |
| .subscribe_event = omap3isp_stat_subscribe_event, |
| .unsubscribe_event = omap3isp_stat_unsubscribe_event, |
| }; |
| |
| static const struct v4l2_subdev_video_ops hist_subdev_video_ops = { |
| .s_stream = omap3isp_stat_s_stream, |
| }; |
| |
| static const struct v4l2_subdev_ops hist_subdev_ops = { |
| .core = &hist_subdev_core_ops, |
| .video = &hist_subdev_video_ops, |
| }; |
| |
| /* |
| * omap3isp_hist_init - Module Initialization. |
| */ |
| int omap3isp_hist_init(struct isp_device *isp) |
| { |
| struct ispstat *hist = &isp->isp_hist; |
| struct omap3isp_hist_config *hist_cfg; |
| int ret = -1; |
| |
| hist_cfg = devm_kzalloc(isp->dev, sizeof(*hist_cfg), GFP_KERNEL); |
| if (hist_cfg == NULL) |
| return -ENOMEM; |
| |
| hist->isp = isp; |
| |
| if (HIST_CONFIG_DMA) |
| ret = omap_request_dma(OMAP24XX_DMA_NO_DEVICE, "DMA_ISP_HIST", |
| hist_dma_cb, hist, &hist->dma_ch); |
| if (ret) { |
| if (HIST_CONFIG_DMA) |
| dev_warn(isp->dev, "hist: DMA request channel failed. " |
| "Using PIO only.\n"); |
| hist->dma_ch = -1; |
| } else { |
| dev_dbg(isp->dev, "hist: DMA channel = %d\n", hist->dma_ch); |
| hist_dma_config(hist); |
| omap_enable_dma_irq(hist->dma_ch, OMAP_DMA_BLOCK_IRQ); |
| } |
| |
| hist->ops = &hist_ops; |
| hist->priv = hist_cfg; |
| hist->event_type = V4L2_EVENT_OMAP3ISP_HIST; |
| |
| ret = omap3isp_stat_init(hist, "histogram", &hist_subdev_ops); |
| if (ret) { |
| if (HIST_USING_DMA(hist)) |
| omap_free_dma(hist->dma_ch); |
| } |
| |
| return ret; |
| } |
| |
| /* |
| * omap3isp_hist_cleanup - Module cleanup. |
| */ |
| void omap3isp_hist_cleanup(struct isp_device *isp) |
| { |
| if (HIST_USING_DMA(&isp->isp_hist)) |
| omap_free_dma(isp->isp_hist.dma_ch); |
| omap3isp_stat_cleanup(&isp->isp_hist); |
| } |