| /* |
| * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com> |
| * |
| * This file is dual-licensed: you can use it either under the terms |
| * of the GPL or the X11 license, at your option. Note that this dual |
| * licensing only applies to this file, and not this project as a |
| * whole. |
| * |
| * a) This file is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of the |
| * License, or (at your option) any later version. |
| * |
| * This file is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * Or, alternatively, |
| * |
| * b) Permission is hereby granted, free of charge, to any person |
| * obtaining a copy of this software and associated documentation |
| * files (the "Software"), to deal in the Software without |
| * restriction, including without limitation the rights to use, |
| * copy, modify, merge, publish, distribute, sublicense, and/or |
| * sell copies of the Software, and to permit persons to whom the |
| * Software is furnished to do so, subject to the following |
| * conditions: |
| * |
| * The above copyright notice and this permission notice shall be |
| * included in all copies or substantial portions of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| * OTHER DEALINGS IN THE SOFTWARE. |
| */ |
| |
| /dts-v1/; |
| #include "sun8i-h3.dtsi" |
| #include "sunxi-common-regulators.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| model = "Beelink X2"; |
| compatible = "roofull,beelink-x2", "allwinner,sun8i-h3"; |
| |
| aliases { |
| serial0 = &uart0; |
| ethernet0 = &emac; |
| ethernet1 = &sdiowifi; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| connector { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_con_in: endpoint { |
| remote-endpoint = <&hdmi_out_con>; |
| }; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| blue { |
| label = "beelink-x2:blue:pwr"; |
| gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ |
| default-state = "on"; |
| }; |
| |
| red { |
| label = "beelink-x2:red:standby"; |
| gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ |
| }; |
| }; |
| |
| wifi_pwrseq: wifi_pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ |
| clocks = <&rtc 1>; |
| clock-names = "ext_clock"; |
| }; |
| |
| sound_spdif { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "On-board SPDIF"; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&spdif>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&spdif_out>; |
| }; |
| }; |
| |
| spdif_out: spdif-out { |
| #sound-dai-cells = <0>; |
| compatible = "linux,spdif-dit"; |
| }; |
| }; |
| |
| &de { |
| status = "okay"; |
| }; |
| |
| &ehci0 { |
| status = "okay"; |
| }; |
| |
| &ehci1 { |
| status = "okay"; |
| }; |
| |
| &emac { |
| phy-handle = <&int_mii_phy>; |
| phy-mode = "mii"; |
| allwinner,leds-active-low; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| status = "okay"; |
| }; |
| |
| &hdmi_out { |
| hdmi_out_con: endpoint { |
| remote-endpoint = <&hdmi_con_in>; |
| }; |
| }; |
| |
| &ir { |
| linux,rc-map-name = "rc-tanix-tx3mini"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&r_ir_rx_pin>; |
| status = "okay"; |
| }; |
| |
| &mmc0 { |
| vmmc-supply = <®_vcc3v3>; |
| bus-width = <4>; |
| cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ |
| status = "okay"; |
| }; |
| |
| &mmc1 { |
| vmmc-supply = <®_vcc3v3>; |
| vqmmc-supply = <®_vcc3v3>; |
| mmc-pwrseq = <&wifi_pwrseq>; |
| bus-width = <4>; |
| non-removable; |
| status = "okay"; |
| |
| /* |
| * Explicitly define the sdio device, so that we can add an ethernet |
| * alias for it (which e.g. makes u-boot set a mac-address). |
| */ |
| sdiowifi: sdio_wifi@1 { |
| reg = <1>; |
| }; |
| }; |
| |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_8bit_pins>; |
| vmmc-supply = <®_vcc3v3>; |
| bus-width = <8>; |
| non-removable; |
| cap-mmc-hw-reset; |
| status = "okay"; |
| }; |
| |
| &ohci0 { |
| status = "okay"; |
| }; |
| |
| &ohci1 { |
| status = "okay"; |
| }; |
| |
| ®_usb0_vbus { |
| gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ |
| status = "okay"; |
| }; |
| |
| &spdif { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spdif_tx_pin>; |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pa_pins>; |
| status = "okay"; |
| }; |
| |
| &usb_otg { |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &usbphy { |
| /* USB VBUS is always on except for the OTG port */ |
| status = "okay"; |
| usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */ |
| usb0_vbus-supply = <®_usb0_vbus>; |
| }; |