blob: bbdb01d2284838c1f47c73b195c1b533b9f5f8e2 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/pci/snps,dw-pcie-ep.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Synopsys DesignWare PCIe endpoint interface
maintainers:
- Jingoo Han <jingoohan1@gmail.com>
- Gustavo Pimentel <gustavo.pimentel@synopsys.com>
description: |
Synopsys DesignWare PCIe host controller endpoint
# Please create a separate DT-schema for your DWC PCIe Endpoint controller
# and make sure it's assigned with the vendor-specific compatible string.
select:
properties:
compatible:
const: snps,dw-pcie-ep
required:
- compatible
allOf:
- $ref: /schemas/pci/pci-ep.yaml#
- $ref: /schemas/pci/snps,dw-pcie-common.yaml#
properties:
reg:
description:
DBI, DBI2 reg-spaces and outbound memory window are required for the
normal controller functioning. iATU memory IO region is also required
if the space is unrolled (IP-core version >= 4.80a).
minItems: 2
maxItems: 7
reg-names:
minItems: 2
maxItems: 7
items:
oneOf:
- description:
Basic DWC PCIe controller configuration-space accessible over
the DBI interface. This memory space is either activated with
CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region
with all spaces. Note iATU/eDMA CSRs are indirectly accessible
via the PL viewports on the DWC PCIe controllers older than
v4.80a.
const: dbi
- description:
Shadow DWC PCIe config-space registers. This space is selected
by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of
the PCI-SIG PCIe CFG-space with the shadow registers for some
PCI Header space, PCI Standard and Extended Structures. It's
mainly relevant for the end-point controller configuration,
but still there are some shadow registers available for the
Root Port mode too.
const: dbi2
- description:
External Local Bus registers. It's an application-dependent
registers normally defined by the platform engineers. The space
can be selected by setting CDM/ELBI = 1 and CS2 = 0 wires or can
be accessed over some platform-specific means (for instance
as a part of a system controller).
enum: [ elbi, app ]
- description:
iATU/eDMA registers common for all device functions. It's an
unrolled memory space with the internal Address Translation
Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1
and CS2 = 1. For IP-core releases prior v4.80a, these registers
have been programmed via an indirect addressing scheme using a
set of viewport CSRs mapped into the PL space. Note iATU is
normally mapped to the 0x0 address of this region, while eDMA
is available at 0x80000 base address.
const: atu
- description:
Platform-specific eDMA registers. Some platforms may have eDMA
CSRs mapped in a non-standard base address. The registers offset
can be changed or the MS/LS-bits of the address can be attached
in an additional RTL block before the MEM-IO transactions reach
the DW PCIe slave interface.
const: dma
- description:
PHY/PCS configuration registers. Some platforms can have the
PCS and PHY CSRs accessible over a dedicated memory mapped
region, but mainly these registers are indirectly accessible
either by means of the embedded PHY viewport schema or by some
platform-specific method.
const: phy
- description:
Outbound iATU-capable memory-region which will be used to
generate various application-specific traffic on the PCIe bus
hierarchy. It's usage scenario depends on the endpoint
functionality, for instance it can be used to create MSI(X)
messages.
const: addr_space
- description:
Vendor-specific CSR names. Consider using the generic names above
for new bindings.
oneOf:
- description: See native 'elbi/app' CSR region for details.
enum: [ link, appl ]
- description: See native 'atu' CSR region for details.
enum: [ atu_dma ]
allOf:
- contains:
const: dbi
- contains:
const: addr_space
interrupts:
description:
There is no mandatory IRQ signals for the normal controller functioning,
but in addition to the native set the platforms may have a link- or
PM-related IRQs specified.
minItems: 1
maxItems: 20
interrupt-names:
minItems: 1
maxItems: 20
items:
oneOf:
- description:
Controller request to read or write virtual product data
from/to the VPD capability registers.
const: vpd
- description:
Link Equalization Request flag is set in the Link Status 2
register (applicable if the corresponding IRQ is enabled in
the Link Control 3 register).
const: l_eq
- description:
Indicates that the eDMA Tx/Rx transfer is complete or that an
error has occurred on the corresponding channel. eDMA can have
eight Tx (Write) and Rx (Read) eDMA channels thus supporting up
to 16 IRQ signals all together. Write eDMA channels shall go
first in the ordered row as per default edma_int[*] bus setup.
pattern: '^dma([0-9]|1[0-5])?$'
- description:
PCIe protocol correctable error or a Data Path protection
correctable error is detected by the automotive/safety
feature.
const: sft_ce
- description:
Indicates that the internal safety mechanism has detected an
uncorrectable error.
const: sft_ue
- description:
Application-specific IRQ raised depending on the vendor-specific
events basis.
const: app
- description:
Vendor-specific IRQ names. Consider using the generic names above
for new bindings.
oneOf:
- description: See native "app" IRQ for details
enum: [ intr ]
max-functions:
maximum: 32
required:
- compatible
- reg
- reg-names
additionalProperties: true
examples:
- |
pcie-ep@dfd00000 {
compatible = "snps,dw-pcie-ep";
reg = <0xdfc00000 0x0001000>, /* IP registers 1 */
<0xdfc01000 0x0001000>, /* IP registers 2 */
<0xd0000000 0x2000000>; /* Configuration space */
reg-names = "dbi", "dbi2", "addr_space";
interrupts = <23>, <24>;
interrupt-names = "dma0", "dma1";
clocks = <&sys_clk 12>, <&sys_clk 24>;
clock-names = "dbi", "ref";
resets = <&sys_rst 12>, <&sys_rst 24>;
reset-names = "dbi", "phy";
phys = <&pcie_phy0>, <&pcie_phy1>, <&pcie_phy2>, <&pcie_phy3>;
phy-names = "pcie0", "pcie1", "pcie2", "pcie3";
max-link-speed = <3>;
max-functions = /bits/ 8 <4>;
};