| #!/bin/bash |
| # SPDX-License-Identifier: GPL-2.0 |
| |
| # +-----------------------+ +------------------------+ |
| # | H1 (vrf) | | H2 (vrf) | |
| # | + $h1.10 | | + $h2.10 | |
| # | | 192.0.2.1/28 | | | 192.0.2.2/28 | |
| # | | | | | | |
| # | | + $h1.20 | | | + $h2.20 | |
| # | \ | 198.51.100.1/24 | | \ | 198.51.100.2/24 | |
| # | \| | | \| | |
| # | + $h1 | | + $h2 | |
| # +----|------------------+ +----|-------------------+ |
| # | | |
| # +----|--------------------------------------------------|-------------------+ |
| # | SW | | | |
| # | +--|--------------------------------------------------|-----------------+ | |
| # | | + $swp1 BR1 (802.1q) + $swp2 | | |
| # | | vid 10 vid 10 | | |
| # | | vid 20 vid 20 | | |
| # | | | | |
| # | | + vx10 (vxlan) + vx20 (vxlan) | | |
| # | | local 192.0.2.17 local 192.0.2.17 | | |
| # | | remote 192.0.2.34 192.0.2.50 remote 192.0.2.34 192.0.2.50 | | |
| # | | id 1000 dstport $VXPORT id 2000 dstport $VXPORT | | |
| # | | vid 10 pvid untagged vid 20 pvid untagged | | |
| # | +-----------------------------------------------------------------------+ | |
| # | | |
| # | 192.0.2.32/28 via 192.0.2.18 | |
| # | 192.0.2.48/28 via 192.0.2.18 | |
| # | | |
| # | + $rp1 | |
| # | | 192.0.2.17/28 | |
| # +----|----------------------------------------------------------------------+ |
| # | |
| # +----|--------------------------------------------------------+ |
| # | | VRP2 (vrf) | |
| # | + $rp2 | |
| # | 192.0.2.18/28 | |
| # | | (maybe) HW |
| # ============================================================================= |
| # | | (likely) SW |
| # | + v1 (veth) + v3 (veth) | |
| # | | 192.0.2.33/28 | 192.0.2.49/28 | |
| # +----|---------------------------------------|----------------+ |
| # | | |
| # +----|------------------------------+ +----|------------------------------+ |
| # | + v2 (veth) NS1 (netns) | | + v4 (veth) NS2 (netns) | |
| # | 192.0.2.34/28 | | 192.0.2.50/28 | |
| # | | | | |
| # | 192.0.2.16/28 via 192.0.2.33 | | 192.0.2.16/28 via 192.0.2.49 | |
| # | 192.0.2.50/32 via 192.0.2.33 | | 192.0.2.34/32 via 192.0.2.49 | |
| # | | | | |
| # | +-------------------------------+ | | +-------------------------------+ | |
| # | | BR2 (802.1q) | | | | BR2 (802.1q) | | |
| # | | + vx10 (vxlan) | | | | + vx10 (vxlan) | | |
| # | | local 192.0.2.34 | | | | local 192.0.2.50 | | |
| # | | remote 192.0.2.17 | | | | remote 192.0.2.17 | | |
| # | | remote 192.0.2.50 | | | | remote 192.0.2.34 | | |
| # | | id 1000 dstport $VXPORT | | | | id 1000 dstport $VXPORT | | |
| # | | vid 10 pvid untagged | | | | vid 10 pvid untagged | | |
| # | | | | | | | | |
| # | | + vx20 (vxlan) | | | | + vx20 (vxlan) | | |
| # | | local 192.0.2.34 | | | | local 192.0.2.50 | | |
| # | | remote 192.0.2.17 | | | | remote 192.0.2.17 | | |
| # | | remote 192.0.2.50 | | | | remote 192.0.2.34 | | |
| # | | id 2000 dstport $VXPORT | | | | id 2000 dstport $VXPORT | | |
| # | | vid 20 pvid untagged | | | | vid 20 pvid untagged | | |
| # | | | | | | | | |
| # | | + w1 (veth) | | | | + w1 (veth) | | |
| # | | | vid 10 | | | | | vid 10 | | |
| # | | | vid 20 | | | | | vid 20 | | |
| # | +--|----------------------------+ | | +--|----------------------------+ | |
| # | | | | | | |
| # | +--|----------------------------+ | | +--|----------------------------+ | |
| # | | + w2 (veth) VW2 (vrf) | | | | + w2 (veth) VW2 (vrf) | | |
| # | | |\ | | | | |\ | | |
| # | | | + w2.10 | | | | | + w2.10 | | |
| # | | | 192.0.2.3/28 | | | | | 192.0.2.4/28 | | |
| # | | | | | | | | | | |
| # | | + w2.20 | | | | + w2.20 | | |
| # | | 198.51.100.3/24 | | | | 198.51.100.4/24 | | |
| # | +-------------------------------+ | | +-------------------------------+ | |
| # +-----------------------------------+ +-----------------------------------+ |
| |
| : ${VXPORT:=4789} |
| export VXPORT |
| |
| : ${ALL_TESTS:=" |
| ping_ipv4 |
| test_flood |
| test_unicast |
| reapply_config |
| ping_ipv4 |
| test_flood |
| test_unicast |
| test_learning |
| test_pvid |
| "} |
| |
| NUM_NETIFS=6 |
| source lib.sh |
| |
| h1_create() |
| { |
| simple_if_init $h1 |
| tc qdisc add dev $h1 clsact |
| vlan_create $h1 10 v$h1 192.0.2.1/28 |
| vlan_create $h1 20 v$h1 198.51.100.1/24 |
| } |
| |
| h1_destroy() |
| { |
| vlan_destroy $h1 20 |
| vlan_destroy $h1 10 |
| tc qdisc del dev $h1 clsact |
| simple_if_fini $h1 |
| } |
| |
| h2_create() |
| { |
| simple_if_init $h2 |
| tc qdisc add dev $h2 clsact |
| vlan_create $h2 10 v$h2 192.0.2.2/28 |
| vlan_create $h2 20 v$h2 198.51.100.2/24 |
| } |
| |
| h2_destroy() |
| { |
| vlan_destroy $h2 20 |
| vlan_destroy $h2 10 |
| tc qdisc del dev $h2 clsact |
| simple_if_fini $h2 |
| } |
| |
| rp1_set_addr() |
| { |
| ip address add dev $rp1 192.0.2.17/28 |
| |
| ip route add 192.0.2.32/28 nexthop via 192.0.2.18 |
| ip route add 192.0.2.48/28 nexthop via 192.0.2.18 |
| } |
| |
| rp1_unset_addr() |
| { |
| ip route del 192.0.2.48/28 nexthop via 192.0.2.18 |
| ip route del 192.0.2.32/28 nexthop via 192.0.2.18 |
| |
| ip address del dev $rp1 192.0.2.17/28 |
| } |
| |
| switch_create() |
| { |
| ip link add name br1 type bridge vlan_filtering 1 vlan_default_pvid 0 \ |
| mcast_snooping 0 |
| # Make sure the bridge uses the MAC address of the local port and not |
| # that of the VxLAN's device. |
| ip link set dev br1 address $(mac_get $swp1) |
| ip link set dev br1 up |
| |
| ip link set dev $rp1 up |
| rp1_set_addr |
| |
| ip link add name vx10 type vxlan id 1000 \ |
| local 192.0.2.17 dstport "$VXPORT" \ |
| nolearning noudpcsum tos inherit ttl 100 |
| ip link set dev vx10 up |
| |
| ip link set dev vx10 master br1 |
| bridge vlan add vid 10 dev vx10 pvid untagged |
| |
| ip link add name vx20 type vxlan id 2000 \ |
| local 192.0.2.17 dstport "$VXPORT" \ |
| nolearning noudpcsum tos inherit ttl 100 |
| ip link set dev vx20 up |
| |
| ip link set dev vx20 master br1 |
| bridge vlan add vid 20 dev vx20 pvid untagged |
| |
| ip link set dev $swp1 master br1 |
| ip link set dev $swp1 up |
| bridge vlan add vid 10 dev $swp1 |
| bridge vlan add vid 20 dev $swp1 |
| |
| ip link set dev $swp2 master br1 |
| ip link set dev $swp2 up |
| bridge vlan add vid 10 dev $swp2 |
| bridge vlan add vid 20 dev $swp2 |
| |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst 192.0.2.34 self |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst 192.0.2.50 self |
| |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst 192.0.2.34 self |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst 192.0.2.50 self |
| } |
| |
| switch_destroy() |
| { |
| bridge fdb del dev vx20 00:00:00:00:00:00 dst 192.0.2.50 self |
| bridge fdb del dev vx20 00:00:00:00:00:00 dst 192.0.2.34 self |
| |
| bridge fdb del dev vx10 00:00:00:00:00:00 dst 192.0.2.50 self |
| bridge fdb del dev vx10 00:00:00:00:00:00 dst 192.0.2.34 self |
| |
| bridge vlan del vid 20 dev $swp2 |
| bridge vlan del vid 10 dev $swp2 |
| ip link set dev $swp2 down |
| ip link set dev $swp2 nomaster |
| |
| bridge vlan del vid 20 dev $swp1 |
| bridge vlan del vid 10 dev $swp1 |
| ip link set dev $swp1 down |
| ip link set dev $swp1 nomaster |
| |
| bridge vlan del vid 20 dev vx20 |
| ip link set dev vx20 nomaster |
| |
| ip link set dev vx20 down |
| ip link del dev vx20 |
| |
| bridge vlan del vid 10 dev vx10 |
| ip link set dev vx10 nomaster |
| |
| ip link set dev vx10 down |
| ip link del dev vx10 |
| |
| rp1_unset_addr |
| ip link set dev $rp1 down |
| |
| ip link set dev br1 down |
| ip link del dev br1 |
| } |
| |
| vrp2_create() |
| { |
| simple_if_init $rp2 192.0.2.18/28 |
| __simple_if_init v1 v$rp2 192.0.2.33/28 |
| __simple_if_init v3 v$rp2 192.0.2.49/28 |
| tc qdisc add dev v1 clsact |
| } |
| |
| vrp2_destroy() |
| { |
| tc qdisc del dev v1 clsact |
| __simple_if_fini v3 192.0.2.49/28 |
| __simple_if_fini v1 192.0.2.33/28 |
| simple_if_fini $rp2 192.0.2.18/28 |
| } |
| |
| ns_init_common() |
| { |
| local in_if=$1; shift |
| local in_addr=$1; shift |
| local other_in_addr=$1; shift |
| local nh_addr=$1; shift |
| local host_addr1=$1; shift |
| local host_addr2=$1; shift |
| |
| ip link set dev $in_if up |
| ip address add dev $in_if $in_addr/28 |
| tc qdisc add dev $in_if clsact |
| |
| ip link add name br2 type bridge vlan_filtering 1 vlan_default_pvid 0 |
| ip link set dev br2 up |
| |
| ip link add name w1 type veth peer name w2 |
| |
| ip link set dev w1 master br2 |
| ip link set dev w1 up |
| |
| bridge vlan add vid 10 dev w1 |
| bridge vlan add vid 20 dev w1 |
| |
| ip link add name vx10 type vxlan id 1000 local $in_addr \ |
| dstport "$VXPORT" |
| ip link set dev vx10 up |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst 192.0.2.17 self |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst $other_in_addr self |
| |
| ip link set dev vx10 master br2 |
| tc qdisc add dev vx10 clsact |
| |
| bridge vlan add vid 10 dev vx10 pvid untagged |
| |
| ip link add name vx20 type vxlan id 2000 local $in_addr \ |
| dstport "$VXPORT" |
| ip link set dev vx20 up |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst 192.0.2.17 self |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst $other_in_addr self |
| |
| ip link set dev vx20 master br2 |
| tc qdisc add dev vx20 clsact |
| |
| bridge vlan add vid 20 dev vx20 pvid untagged |
| |
| simple_if_init w2 |
| vlan_create w2 10 vw2 $host_addr1/28 |
| vlan_create w2 20 vw2 $host_addr2/24 |
| |
| ip route add 192.0.2.16/28 nexthop via $nh_addr |
| ip route add $other_in_addr/32 nexthop via $nh_addr |
| } |
| export -f ns_init_common |
| |
| ns1_create() |
| { |
| ip netns add ns1 |
| ip link set dev v2 netns ns1 |
| in_ns ns1 \ |
| ns_init_common v2 192.0.2.34 192.0.2.50 192.0.2.33 192.0.2.3 \ |
| 198.51.100.3 |
| } |
| |
| ns1_destroy() |
| { |
| ip netns exec ns1 ip link set dev v2 netns 1 |
| ip netns del ns1 |
| } |
| |
| ns2_create() |
| { |
| ip netns add ns2 |
| ip link set dev v4 netns ns2 |
| in_ns ns2 \ |
| ns_init_common v4 192.0.2.50 192.0.2.34 192.0.2.49 192.0.2.4 \ |
| 198.51.100.4 |
| } |
| |
| ns2_destroy() |
| { |
| ip netns exec ns2 ip link set dev v4 netns 1 |
| ip netns del ns2 |
| } |
| |
| setup_prepare() |
| { |
| h1=${NETIFS[p1]} |
| swp1=${NETIFS[p2]} |
| |
| swp2=${NETIFS[p3]} |
| h2=${NETIFS[p4]} |
| |
| rp1=${NETIFS[p5]} |
| rp2=${NETIFS[p6]} |
| |
| vrf_prepare |
| forwarding_enable |
| |
| h1_create |
| h2_create |
| switch_create |
| |
| ip link add name v1 type veth peer name v2 |
| ip link add name v3 type veth peer name v4 |
| vrp2_create |
| ns1_create |
| ns2_create |
| |
| r1_mac=$(in_ns ns1 mac_get w2) |
| r2_mac=$(in_ns ns2 mac_get w2) |
| h2_mac=$(mac_get $h2) |
| } |
| |
| cleanup() |
| { |
| pre_cleanup |
| |
| ns2_destroy |
| ns1_destroy |
| vrp2_destroy |
| ip link del dev v3 |
| ip link del dev v1 |
| |
| switch_destroy |
| h2_destroy |
| h1_destroy |
| |
| forwarding_restore |
| vrf_cleanup |
| } |
| |
| # For the first round of tests, vx10 and vx20 were the first devices to get |
| # attached to the bridge, and that at the point that the local IP is already |
| # configured. Try the other scenario of attaching these devices to a bridge |
| # that already has local ports members, and only then assign the local IP. |
| reapply_config() |
| { |
| log_info "Reapplying configuration" |
| |
| bridge fdb del dev vx20 00:00:00:00:00:00 dst 192.0.2.50 self |
| bridge fdb del dev vx20 00:00:00:00:00:00 dst 192.0.2.34 self |
| |
| bridge fdb del dev vx10 00:00:00:00:00:00 dst 192.0.2.50 self |
| bridge fdb del dev vx10 00:00:00:00:00:00 dst 192.0.2.34 self |
| |
| ip link set dev vx20 nomaster |
| ip link set dev vx10 nomaster |
| |
| rp1_unset_addr |
| sleep 5 |
| |
| ip link set dev vx10 master br1 |
| bridge vlan add vid 10 dev vx10 pvid untagged |
| |
| ip link set dev vx20 master br1 |
| bridge vlan add vid 20 dev vx20 pvid untagged |
| |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst 192.0.2.34 self |
| bridge fdb append dev vx10 00:00:00:00:00:00 dst 192.0.2.50 self |
| |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst 192.0.2.34 self |
| bridge fdb append dev vx20 00:00:00:00:00:00 dst 192.0.2.50 self |
| |
| rp1_set_addr |
| sleep 5 |
| } |
| |
| ping_ipv4() |
| { |
| ping_test $h1.10 192.0.2.2 ": local->local vid 10" |
| ping_test $h1.20 198.51.100.2 ": local->local vid 20" |
| ping_test $h1.10 192.0.2.3 ": local->remote 1 vid 10" |
| ping_test $h1.10 192.0.2.4 ": local->remote 2 vid 10" |
| ping_test $h1.20 198.51.100.3 ": local->remote 1 vid 20" |
| ping_test $h1.20 198.51.100.4 ": local->remote 2 vid 20" |
| } |
| |
| maybe_in_ns() |
| { |
| echo ${1:+in_ns} $1 |
| } |
| |
| __flood_counter_add_del() |
| { |
| local add_del=$1; shift |
| local dev=$1; shift |
| local ns=$1; shift |
| |
| # Putting the ICMP capture both to HW and to SW will end up |
| # double-counting the packets that are trapped to slow path, such as for |
| # the unicast test. Adding either skip_hw or skip_sw fixes this problem, |
| # but with skip_hw, the flooded packets are not counted at all, because |
| # those are dropped due to MAC address mismatch; and skip_sw is a no-go |
| # for veth-based topologies. |
| # |
| # So try to install with skip_sw and fall back to skip_sw if that fails. |
| |
| $(maybe_in_ns $ns) __icmp_capture_add_del \ |
| $add_del 100 "" $dev skip_sw 2>/dev/null || \ |
| $(maybe_in_ns $ns) __icmp_capture_add_del \ |
| $add_del 100 "" $dev skip_hw |
| } |
| |
| flood_counter_install() |
| { |
| __flood_counter_add_del add "$@" |
| } |
| |
| flood_counter_uninstall() |
| { |
| __flood_counter_add_del del "$@" |
| } |
| |
| flood_fetch_stat() |
| { |
| local dev=$1; shift |
| local ns=$1; shift |
| |
| $(maybe_in_ns $ns) tc_rule_stats_get $dev 100 ingress |
| } |
| |
| flood_fetch_stats() |
| { |
| local counters=("${@}") |
| local counter |
| |
| for counter in "${counters[@]}"; do |
| flood_fetch_stat $counter |
| done |
| } |
| |
| vxlan_flood_test() |
| { |
| local mac=$1; shift |
| local dst=$1; shift |
| local vid=$1; shift |
| local -a expects=("${@}") |
| |
| local -a counters=($h2 "vx10 ns1" "vx20 ns1" "vx10 ns2" "vx20 ns2") |
| local counter |
| local key |
| |
| # Packets reach the local host tagged whereas they reach the VxLAN |
| # devices untagged. In order to be able to use the same filter for |
| # all counters, make sure the packets also reach the local host |
| # untagged |
| bridge vlan add vid $vid dev $swp2 untagged |
| for counter in "${counters[@]}"; do |
| flood_counter_install $counter |
| done |
| |
| local -a t0s=($(flood_fetch_stats "${counters[@]}")) |
| $MZ $h1 -Q $vid -c 10 -d 100msec -p 64 -b $mac -B $dst -t icmp -q |
| sleep 1 |
| local -a t1s=($(flood_fetch_stats "${counters[@]}")) |
| |
| for key in ${!t0s[@]}; do |
| local delta=$((t1s[$key] - t0s[$key])) |
| local expect=${expects[$key]} |
| |
| ((expect == delta)) |
| check_err $? "${counters[$key]}: Expected to capture $expect packets, got $delta." |
| done |
| |
| for counter in "${counters[@]}"; do |
| flood_counter_uninstall $counter |
| done |
| bridge vlan add vid $vid dev $swp2 |
| } |
| |
| __test_flood() |
| { |
| local mac=$1; shift |
| local dst=$1; shift |
| local vid=$1; shift |
| local what=$1; shift |
| local -a expects=("${@}") |
| |
| RET=0 |
| |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: $what" |
| } |
| |
| test_flood() |
| { |
| __test_flood de:ad:be:ef:13:37 192.0.2.100 10 "flood vlan 10" \ |
| 10 10 0 10 0 |
| __test_flood ca:fe:be:ef:13:37 198.51.100.100 20 "flood vlan 20" \ |
| 10 0 10 0 10 |
| } |
| |
| vxlan_fdb_add_del() |
| { |
| local add_del=$1; shift |
| local vid=$1; shift |
| local mac=$1; shift |
| local dev=$1; shift |
| local dst=$1; shift |
| |
| bridge fdb $add_del dev $dev $mac self static permanent \ |
| ${dst:+dst} $dst 2>/dev/null |
| bridge fdb $add_del dev $dev $mac master static vlan $vid 2>/dev/null |
| } |
| |
| __test_unicast() |
| { |
| local mac=$1; shift |
| local dst=$1; shift |
| local hit_idx=$1; shift |
| local vid=$1; shift |
| local what=$1; shift |
| |
| RET=0 |
| |
| local -a expects=(0 0 0 0 0) |
| expects[$hit_idx]=10 |
| |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: $what" |
| } |
| |
| test_unicast() |
| { |
| local -a targets=("$h2_mac $h2" |
| "$r1_mac vx10 192.0.2.34" |
| "$r2_mac vx10 192.0.2.50") |
| local target |
| |
| log_info "unicast vlan 10" |
| |
| for target in "${targets[@]}"; do |
| vxlan_fdb_add_del add 10 $target |
| done |
| |
| __test_unicast $h2_mac 192.0.2.2 0 10 "local MAC unicast" |
| __test_unicast $r1_mac 192.0.2.3 1 10 "remote MAC 1 unicast" |
| __test_unicast $r2_mac 192.0.2.4 3 10 "remote MAC 2 unicast" |
| |
| for target in "${targets[@]}"; do |
| vxlan_fdb_add_del del 10 $target |
| done |
| |
| log_info "unicast vlan 20" |
| |
| targets=("$h2_mac $h2" "$r1_mac vx20 192.0.2.34" \ |
| "$r2_mac vx20 192.0.2.50") |
| |
| for target in "${targets[@]}"; do |
| vxlan_fdb_add_del add 20 $target |
| done |
| |
| __test_unicast $h2_mac 198.51.100.2 0 20 "local MAC unicast" |
| __test_unicast $r1_mac 198.51.100.3 2 20 "remote MAC 1 unicast" |
| __test_unicast $r2_mac 198.51.100.4 4 20 "remote MAC 2 unicast" |
| |
| for target in "${targets[@]}"; do |
| vxlan_fdb_add_del del 20 $target |
| done |
| } |
| |
| test_pvid() |
| { |
| local -a expects=(0 0 0 0 0) |
| local mac=de:ad:be:ef:13:37 |
| local dst=192.0.2.100 |
| local vid=10 |
| |
| # Check that flooding works |
| RET=0 |
| |
| expects[0]=10; expects[1]=10; expects[3]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood before pvid off" |
| |
| # Toggle PVID off and test that flood to remote hosts does not work |
| RET=0 |
| |
| bridge vlan add vid 10 dev vx10 |
| |
| expects[0]=10; expects[1]=0; expects[3]=0 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood after pvid off" |
| |
| # Toggle PVID on and test that flood to remote hosts does work |
| RET=0 |
| |
| bridge vlan add vid 10 dev vx10 pvid untagged |
| |
| expects[0]=10; expects[1]=10; expects[3]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood after pvid on" |
| |
| # Add a new VLAN and test that it does not affect flooding |
| RET=0 |
| |
| bridge vlan add vid 30 dev vx10 |
| |
| expects[0]=10; expects[1]=10; expects[3]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| bridge vlan del vid 30 dev vx10 |
| |
| log_test "VXLAN: flood after vlan add" |
| |
| # Remove currently mapped VLAN and test that flood to remote hosts does |
| # not work |
| RET=0 |
| |
| bridge vlan del vid 10 dev vx10 |
| |
| expects[0]=10; expects[1]=0; expects[3]=0 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood after vlan delete" |
| |
| # Re-add the VLAN and test that flood to remote hosts does work |
| RET=0 |
| |
| bridge vlan add vid 10 dev vx10 pvid untagged |
| |
| expects[0]=10; expects[1]=10; expects[3]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood after vlan re-add" |
| } |
| |
| __test_learning() |
| { |
| local -a expects=(0 0 0 0 0) |
| local mac=$1; shift |
| local dst=$1; shift |
| local vid=$1; shift |
| local idx1=$1; shift |
| local idx2=$1; shift |
| local vx=vx$vid |
| |
| # Check that flooding works |
| RET=0 |
| |
| expects[0]=10; expects[$idx1]=10; expects[$idx2]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: flood before learning" |
| |
| # Send a packet with source mac set to $mac from host w2 and check that |
| # a corresponding entry is created in the VxLAN device |
| RET=0 |
| |
| in_ns ns1 $MZ w2 -Q $vid -c 1 -p 64 -a $mac -b ff:ff:ff:ff:ff:ff \ |
| -B $dst -t icmp -q |
| sleep 1 |
| |
| bridge fdb show brport $vx | grep $mac | grep -q self |
| check_err $? |
| bridge fdb show brport $vx | grep $mac | grep "vlan $vid" \ |
| | grep -q -v self |
| check_err $? |
| |
| log_test "VXLAN: show learned FDB entry" |
| |
| # Repeat first test and check that packets only reach host w2 in ns1 |
| RET=0 |
| |
| expects[0]=0; expects[$idx1]=10; expects[$idx2]=0 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: learned FDB entry" |
| |
| # Delete the learned FDB entry from the VxLAN and bridge devices and |
| # check that packets are flooded |
| RET=0 |
| |
| bridge fdb del dev $vx $mac master self vlan $vid |
| sleep 1 |
| |
| expects[0]=10; expects[$idx1]=10; expects[$idx2]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: deletion of learned FDB entry" |
| |
| # Re-learn the first FDB entry and check that it is correctly aged-out |
| RET=0 |
| |
| in_ns ns1 $MZ w2 -Q $vid -c 1 -p 64 -a $mac -b ff:ff:ff:ff:ff:ff \ |
| -B $dst -t icmp -q |
| sleep 1 |
| |
| bridge fdb show brport $vx | grep $mac | grep -q self |
| check_err $? |
| bridge fdb show brport $vx | grep $mac | grep "vlan $vid" \ |
| | grep -q -v self |
| check_err $? |
| |
| expects[0]=0; expects[$idx1]=10; expects[$idx2]=0 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| sleep 20 |
| |
| bridge fdb show brport $vx | grep $mac | grep -q self |
| check_fail $? |
| bridge fdb show brport $vx | grep $mac | grep "vlan $vid" \ |
| | grep -q -v self |
| check_fail $? |
| |
| expects[0]=10; expects[$idx1]=10; expects[$idx2]=10 |
| vxlan_flood_test $mac $dst $vid "${expects[@]}" |
| |
| log_test "VXLAN: Ageing of learned FDB entry" |
| |
| # Toggle learning on the bridge port and check that the bridge's FDB |
| # is populated only when it should |
| RET=0 |
| |
| ip link set dev $vx type bridge_slave learning off |
| |
| in_ns ns1 $MZ w2 -Q $vid -c 1 -p 64 -a $mac -b ff:ff:ff:ff:ff:ff \ |
| -B $dst -t icmp -q |
| sleep 1 |
| |
| bridge fdb show brport $vx | grep $mac | grep "vlan $vid" \ |
| | grep -q -v self |
| check_fail $? |
| |
| ip link set dev $vx type bridge_slave learning on |
| |
| in_ns ns1 $MZ w2 -Q $vid -c 1 -p 64 -a $mac -b ff:ff:ff:ff:ff:ff \ |
| -B $dst -t icmp -q |
| sleep 1 |
| |
| bridge fdb show brport $vx | grep $mac | grep "vlan $vid" \ |
| | grep -q -v self |
| check_err $? |
| |
| log_test "VXLAN: learning toggling on bridge port" |
| } |
| |
| test_learning() |
| { |
| local mac=de:ad:be:ef:13:37 |
| local dst=192.0.2.100 |
| local vid=10 |
| |
| # Enable learning on the VxLAN devices and set ageing time to 10 seconds |
| ip link set dev br1 type bridge ageing_time 1000 |
| ip link set dev vx10 type vxlan ageing 10 |
| ip link set dev vx10 type vxlan learning |
| ip link set dev vx20 type vxlan ageing 10 |
| ip link set dev vx20 type vxlan learning |
| reapply_config |
| |
| log_info "learning vlan 10" |
| |
| __test_learning $mac $dst $vid 1 3 |
| |
| log_info "learning vlan 20" |
| |
| mac=ca:fe:be:ef:13:37 |
| dst=198.51.100.100 |
| vid=20 |
| |
| __test_learning $mac $dst $vid 2 4 |
| |
| # Restore previous settings |
| ip link set dev vx20 type vxlan nolearning |
| ip link set dev vx20 type vxlan ageing 300 |
| ip link set dev vx10 type vxlan nolearning |
| ip link set dev vx10 type vxlan ageing 300 |
| ip link set dev br1 type bridge ageing_time 30000 |
| reapply_config |
| } |
| |
| test_all() |
| { |
| log_info "Running tests with UDP port $VXPORT" |
| tests_run |
| } |
| |
| trap cleanup EXIT |
| |
| setup_prepare |
| setup_wait |
| test_all |
| |
| exit $EXIT_STATUS |
