blob: de19e68eb84e097b3d89ee696474a819cfce4f5b [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
/dts-v1/;
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "OrangePi Zero Plus2";
compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
pwr {
label = "orangepi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
status {
label = "orangepi:red:status";
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
};
};
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
post-power-on-delay-ms = <200>;
};
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&r_pio>;
interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
&usb_otg {
/*
* According to schematics CN1 MicroUSB port can be used to take
* external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
* port cannot provide power externally even if the board is powered
* via GPIO pins. It thus makes sense to force peripheral mode.
*/
dr_mode = "peripheral";
status = "okay";
};
&usbphy {
status = "okay";
};