|  | /******************************************************************************* | 
|  |  | 
|  | Intel 10 Gigabit PCI Express Linux driver | 
|  | Copyright(c) 1999 - 2014 Intel Corporation. | 
|  |  | 
|  | This program is free software; you can redistribute it and/or modify it | 
|  | under the terms and conditions of the GNU General Public License, | 
|  | version 2, as published by the Free Software Foundation. | 
|  |  | 
|  | This program is distributed in the hope it will be useful, but WITHOUT | 
|  | ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | 
|  | FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for | 
|  | more details. | 
|  |  | 
|  | You should have received a copy of the GNU General Public License along with | 
|  | this program; if not, write to the Free Software Foundation, Inc., | 
|  | 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. | 
|  |  | 
|  | The full GNU General Public License is included in this distribution in | 
|  | the file called "COPYING". | 
|  |  | 
|  | Contact Information: | 
|  | Linux NICS <linux.nics@intel.com> | 
|  | e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> | 
|  | Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 | 
|  |  | 
|  | *******************************************************************************/ | 
|  |  | 
|  | #include <linux/types.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/pci.h> | 
|  | #include <linux/netdevice.h> | 
|  | #include <linux/vmalloc.h> | 
|  | #include <linux/string.h> | 
|  | #include <linux/in.h> | 
|  | #include <linux/ip.h> | 
|  | #include <linux/tcp.h> | 
|  | #include <linux/ipv6.h> | 
|  | #ifdef NETIF_F_HW_VLAN_CTAG_TX | 
|  | #include <linux/if_vlan.h> | 
|  | #endif | 
|  |  | 
|  | #include "ixgbe.h" | 
|  | #include "ixgbe_type.h" | 
|  | #include "ixgbe_sriov.h" | 
|  |  | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | static int __ixgbe_enable_sriov(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int num_vf_macvlans, i; | 
|  | struct vf_macvlans *mv_list; | 
|  |  | 
|  | adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED; | 
|  | e_info(probe, "SR-IOV enabled with %d VFs\n", adapter->num_vfs); | 
|  |  | 
|  | /* Enable VMDq flag so device will be set in VM mode */ | 
|  | adapter->flags |= IXGBE_FLAG_VMDQ_ENABLED; | 
|  | if (!adapter->ring_feature[RING_F_VMDQ].limit) | 
|  | adapter->ring_feature[RING_F_VMDQ].limit = 1; | 
|  | adapter->ring_feature[RING_F_VMDQ].offset = adapter->num_vfs; | 
|  |  | 
|  | num_vf_macvlans = hw->mac.num_rar_entries - | 
|  | (IXGBE_MAX_PF_MACVLANS + 1 + adapter->num_vfs); | 
|  |  | 
|  | adapter->mv_list = mv_list = kcalloc(num_vf_macvlans, | 
|  | sizeof(struct vf_macvlans), | 
|  | GFP_KERNEL); | 
|  | if (mv_list) { | 
|  | /* Initialize list of VF macvlans */ | 
|  | INIT_LIST_HEAD(&adapter->vf_mvs.l); | 
|  | for (i = 0; i < num_vf_macvlans; i++) { | 
|  | mv_list->vf = -1; | 
|  | mv_list->free = true; | 
|  | list_add(&mv_list->l, &adapter->vf_mvs.l); | 
|  | mv_list++; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* Initialize default switching mode VEB */ | 
|  | IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, IXGBE_PFDTXGSWC_VT_LBEN); | 
|  | adapter->flags2 |= IXGBE_FLAG2_BRIDGE_MODE_VEB; | 
|  |  | 
|  | /* If call to enable VFs succeeded then allocate memory | 
|  | * for per VF control structures. | 
|  | */ | 
|  | adapter->vfinfo = | 
|  | kcalloc(adapter->num_vfs, | 
|  | sizeof(struct vf_data_storage), GFP_KERNEL); | 
|  | if (adapter->vfinfo) { | 
|  | /* limit trafffic classes based on VFs enabled */ | 
|  | if ((adapter->hw.mac.type == ixgbe_mac_82599EB) && | 
|  | (adapter->num_vfs < 16)) { | 
|  | adapter->dcb_cfg.num_tcs.pg_tcs = MAX_TRAFFIC_CLASS; | 
|  | adapter->dcb_cfg.num_tcs.pfc_tcs = MAX_TRAFFIC_CLASS; | 
|  | } else if (adapter->num_vfs < 32) { | 
|  | adapter->dcb_cfg.num_tcs.pg_tcs = 4; | 
|  | adapter->dcb_cfg.num_tcs.pfc_tcs = 4; | 
|  | } else { | 
|  | adapter->dcb_cfg.num_tcs.pg_tcs = 1; | 
|  | adapter->dcb_cfg.num_tcs.pfc_tcs = 1; | 
|  | } | 
|  |  | 
|  | /* We do not support RSS w/ SR-IOV */ | 
|  | adapter->ring_feature[RING_F_RSS].limit = 1; | 
|  |  | 
|  | /* Disable RSC when in SR-IOV mode */ | 
|  | adapter->flags2 &= ~(IXGBE_FLAG2_RSC_CAPABLE | | 
|  | IXGBE_FLAG2_RSC_ENABLED); | 
|  |  | 
|  | /* enable spoof checking for all VFs */ | 
|  | for (i = 0; i < adapter->num_vfs; i++) | 
|  | adapter->vfinfo[i].spoofchk_enabled = true; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | /* Note this function is called when the user wants to enable SR-IOV | 
|  | * VFs using the now deprecated module parameter | 
|  | */ | 
|  | void ixgbe_enable_sriov(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | int pre_existing_vfs = 0; | 
|  |  | 
|  | pre_existing_vfs = pci_num_vf(adapter->pdev); | 
|  | if (!pre_existing_vfs && !adapter->num_vfs) | 
|  | return; | 
|  |  | 
|  | /* If there are pre-existing VFs then we have to force | 
|  | * use of that many - over ride any module parameter value. | 
|  | * This may result from the user unloading the PF driver | 
|  | * while VFs were assigned to guest VMs or because the VFs | 
|  | * have been created via the new PCI SR-IOV sysfs interface. | 
|  | */ | 
|  | if (pre_existing_vfs) { | 
|  | adapter->num_vfs = pre_existing_vfs; | 
|  | dev_warn(&adapter->pdev->dev, | 
|  | "Virtual Functions already enabled for this device - Please reload all VF drivers to avoid spoofed packet errors\n"); | 
|  | } else { | 
|  | int err; | 
|  | /* | 
|  | * The 82599 supports up to 64 VFs per physical function | 
|  | * but this implementation limits allocation to 63 so that | 
|  | * basic networking resources are still available to the | 
|  | * physical function.  If the user requests greater thn | 
|  | * 63 VFs then it is an error - reset to default of zero. | 
|  | */ | 
|  | adapter->num_vfs = min_t(unsigned int, adapter->num_vfs, IXGBE_MAX_VFS_DRV_LIMIT); | 
|  |  | 
|  | err = pci_enable_sriov(adapter->pdev, adapter->num_vfs); | 
|  | if (err) { | 
|  | e_err(probe, "Failed to enable PCI sriov: %d\n", err); | 
|  | adapter->num_vfs = 0; | 
|  | return; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (!__ixgbe_enable_sriov(adapter)) | 
|  | return; | 
|  |  | 
|  | /* If we have gotten to this point then there is no memory available | 
|  | * to manage the VF devices - print message and bail. | 
|  | */ | 
|  | e_err(probe, "Unable to allocate memory for VF Data Storage - " | 
|  | "SRIOV disabled\n"); | 
|  | ixgbe_disable_sriov(adapter); | 
|  | } | 
|  |  | 
|  | #endif /* #ifdef CONFIG_PCI_IOV */ | 
|  | int ixgbe_disable_sriov(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 gpie; | 
|  | u32 vmdctl; | 
|  | int rss; | 
|  |  | 
|  | /* set num VFs to 0 to prevent access to vfinfo */ | 
|  | adapter->num_vfs = 0; | 
|  |  | 
|  | /* free VF control structures */ | 
|  | kfree(adapter->vfinfo); | 
|  | adapter->vfinfo = NULL; | 
|  |  | 
|  | /* free macvlan list */ | 
|  | kfree(adapter->mv_list); | 
|  | adapter->mv_list = NULL; | 
|  |  | 
|  | /* if SR-IOV is already disabled then there is nothing to do */ | 
|  | if (!(adapter->flags & IXGBE_FLAG_SRIOV_ENABLED)) | 
|  | return 0; | 
|  |  | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | /* | 
|  | * If our VFs are assigned we cannot shut down SR-IOV | 
|  | * without causing issues, so just leave the hardware | 
|  | * available but disabled | 
|  | */ | 
|  | if (pci_vfs_assigned(adapter->pdev)) { | 
|  | e_dev_warn("Unloading driver while VFs are assigned - VFs will not be deallocated\n"); | 
|  | return -EPERM; | 
|  | } | 
|  | /* disable iov and allow time for transactions to clear */ | 
|  | pci_disable_sriov(adapter->pdev); | 
|  | #endif | 
|  |  | 
|  | /* turn off device IOV mode */ | 
|  | IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, 0); | 
|  | gpie = IXGBE_READ_REG(hw, IXGBE_GPIE); | 
|  | gpie &= ~IXGBE_GPIE_VTMODE_MASK; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie); | 
|  |  | 
|  | /* set default pool back to 0 */ | 
|  | vmdctl = IXGBE_READ_REG(hw, IXGBE_VT_CTL); | 
|  | vmdctl &= ~IXGBE_VT_CTL_POOL_MASK; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VT_CTL, vmdctl); | 
|  | IXGBE_WRITE_FLUSH(hw); | 
|  |  | 
|  | /* Disable VMDq flag so device will be set in VM mode */ | 
|  | if (adapter->ring_feature[RING_F_VMDQ].limit == 1) { | 
|  | adapter->flags &= ~IXGBE_FLAG_VMDQ_ENABLED; | 
|  | adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED; | 
|  | rss = min_t(int, ixgbe_max_rss_indices(adapter), | 
|  | num_online_cpus()); | 
|  | } else { | 
|  | rss = min_t(int, IXGBE_MAX_L2A_QUEUES, num_online_cpus()); | 
|  | } | 
|  |  | 
|  | adapter->ring_feature[RING_F_VMDQ].offset = 0; | 
|  | adapter->ring_feature[RING_F_RSS].limit = rss; | 
|  |  | 
|  | /* take a breather then clean up driver data */ | 
|  | msleep(100); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_pci_sriov_enable(struct pci_dev *dev, int num_vfs) | 
|  | { | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | struct ixgbe_adapter *adapter = pci_get_drvdata(dev); | 
|  | int err = 0; | 
|  | int i; | 
|  | int pre_existing_vfs = pci_num_vf(dev); | 
|  |  | 
|  | if (pre_existing_vfs && pre_existing_vfs != num_vfs) | 
|  | err = ixgbe_disable_sriov(adapter); | 
|  | else if (pre_existing_vfs && pre_existing_vfs == num_vfs) | 
|  | return num_vfs; | 
|  |  | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | /* While the SR-IOV capability structure reports total VFs to be 64, | 
|  | * we have to limit the actual number allocated based on two factors. | 
|  | * First, we reserve some transmit/receive resources for the PF. | 
|  | * Second, VMDQ also uses the same pools that SR-IOV does. We need to | 
|  | * account for this, so that we don't accidentally allocate more VFs | 
|  | * than we have available pools. The PCI bus driver already checks for | 
|  | * other values out of range. | 
|  | */ | 
|  | if ((num_vfs + adapter->num_rx_pools) > IXGBE_MAX_VF_FUNCTIONS) | 
|  | return -EPERM; | 
|  |  | 
|  | adapter->num_vfs = num_vfs; | 
|  |  | 
|  | err = __ixgbe_enable_sriov(adapter); | 
|  | if (err) | 
|  | return  err; | 
|  |  | 
|  | for (i = 0; i < adapter->num_vfs; i++) | 
|  | ixgbe_vf_configuration(dev, (i | 0x10000000)); | 
|  |  | 
|  | err = pci_enable_sriov(dev, num_vfs); | 
|  | if (err) { | 
|  | e_dev_warn("Failed to enable PCI sriov: %d\n", err); | 
|  | return err; | 
|  | } | 
|  | ixgbe_sriov_reinit(adapter); | 
|  |  | 
|  | return num_vfs; | 
|  | #else | 
|  | return 0; | 
|  | #endif | 
|  | } | 
|  |  | 
|  | static int ixgbe_pci_sriov_disable(struct pci_dev *dev) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = pci_get_drvdata(dev); | 
|  | int err; | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | u32 current_flags = adapter->flags; | 
|  | #endif | 
|  |  | 
|  | err = ixgbe_disable_sriov(adapter); | 
|  |  | 
|  | /* Only reinit if no error and state changed */ | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | if (!err && current_flags != adapter->flags) | 
|  | ixgbe_sriov_reinit(adapter); | 
|  | #endif | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | int ixgbe_pci_sriov_configure(struct pci_dev *dev, int num_vfs) | 
|  | { | 
|  | if (num_vfs == 0) | 
|  | return ixgbe_pci_sriov_disable(dev); | 
|  | else | 
|  | return ixgbe_pci_sriov_enable(dev, num_vfs); | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_multicasts(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | int entries = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) | 
|  | >> IXGBE_VT_MSGINFO_SHIFT; | 
|  | u16 *hash_list = (u16 *)&msgbuf[1]; | 
|  | struct vf_data_storage *vfinfo = &adapter->vfinfo[vf]; | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int i; | 
|  | u32 vector_bit; | 
|  | u32 vector_reg; | 
|  | u32 mta_reg; | 
|  | u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf)); | 
|  |  | 
|  | /* only so many hash values supported */ | 
|  | entries = min(entries, IXGBE_MAX_VF_MC_ENTRIES); | 
|  |  | 
|  | /* | 
|  | * salt away the number of multi cast addresses assigned | 
|  | * to this VF for later use to restore when the PF multi cast | 
|  | * list changes | 
|  | */ | 
|  | vfinfo->num_vf_mc_hashes = entries; | 
|  |  | 
|  | /* | 
|  | * VFs are limited to using the MTA hash table for their multicast | 
|  | * addresses | 
|  | */ | 
|  | for (i = 0; i < entries; i++) { | 
|  | vfinfo->vf_mc_hashes[i] = hash_list[i]; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < vfinfo->num_vf_mc_hashes; i++) { | 
|  | vector_reg = (vfinfo->vf_mc_hashes[i] >> 5) & 0x7F; | 
|  | vector_bit = vfinfo->vf_mc_hashes[i] & 0x1F; | 
|  | mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg)); | 
|  | mta_reg |= (1 << vector_bit); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg); | 
|  | } | 
|  | vmolr |= IXGBE_VMOLR_ROMPE; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_PCI_IOV | 
|  | void ixgbe_restore_vf_multicasts(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | struct vf_data_storage *vfinfo; | 
|  | int i, j; | 
|  | u32 vector_bit; | 
|  | u32 vector_reg; | 
|  | u32 mta_reg; | 
|  |  | 
|  | for (i = 0; i < adapter->num_vfs; i++) { | 
|  | u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(i)); | 
|  | vfinfo = &adapter->vfinfo[i]; | 
|  | for (j = 0; j < vfinfo->num_vf_mc_hashes; j++) { | 
|  | hw->addr_ctrl.mta_in_use++; | 
|  | vector_reg = (vfinfo->vf_mc_hashes[j] >> 5) & 0x7F; | 
|  | vector_bit = vfinfo->vf_mc_hashes[j] & 0x1F; | 
|  | mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg)); | 
|  | mta_reg |= (1 << vector_bit); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg); | 
|  | } | 
|  |  | 
|  | if (vfinfo->num_vf_mc_hashes) | 
|  | vmolr |= IXGBE_VMOLR_ROMPE; | 
|  | else | 
|  | vmolr &= ~IXGBE_VMOLR_ROMPE; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VMOLR(i), vmolr); | 
|  | } | 
|  |  | 
|  | /* Restore any VF macvlans */ | 
|  | ixgbe_full_sync_mac_table(adapter); | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static int ixgbe_set_vf_vlan(struct ixgbe_adapter *adapter, int add, int vid, | 
|  | u32 vf) | 
|  | { | 
|  | /* VLAN 0 is a special case, don't allow it to be removed */ | 
|  | if (!vid && !add) | 
|  | return 0; | 
|  |  | 
|  | return adapter->hw.mac.ops.set_vfta(&adapter->hw, vid, vf, (bool)add); | 
|  | } | 
|  |  | 
|  | static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int max_frame = msgbuf[1]; | 
|  | u32 max_frs; | 
|  |  | 
|  | /* | 
|  | * For 82599EB we have to keep all PFs and VFs operating with | 
|  | * the same max_frame value in order to avoid sending an oversize | 
|  | * frame to a VF.  In order to guarantee this is handled correctly | 
|  | * for all cases we have several special exceptions to take into | 
|  | * account before we can enable the VF for receive | 
|  | */ | 
|  | if (adapter->hw.mac.type == ixgbe_mac_82599EB) { | 
|  | struct net_device *dev = adapter->netdev; | 
|  | int pf_max_frame = dev->mtu + ETH_HLEN; | 
|  | u32 reg_offset, vf_shift, vfre; | 
|  | s32 err = 0; | 
|  |  | 
|  | #ifdef CONFIG_FCOE | 
|  | if (dev->features & NETIF_F_FCOE_MTU) | 
|  | pf_max_frame = max_t(int, pf_max_frame, | 
|  | IXGBE_FCOE_JUMBO_FRAME_SIZE); | 
|  |  | 
|  | #endif /* CONFIG_FCOE */ | 
|  | switch (adapter->vfinfo[vf].vf_api) { | 
|  | case ixgbe_mbox_api_11: | 
|  | /* | 
|  | * Version 1.1 supports jumbo frames on VFs if PF has | 
|  | * jumbo frames enabled which means legacy VFs are | 
|  | * disabled | 
|  | */ | 
|  | if (pf_max_frame > ETH_FRAME_LEN) | 
|  | break; | 
|  | default: | 
|  | /* | 
|  | * If the PF or VF are running w/ jumbo frames enabled | 
|  | * we need to shut down the VF Rx path as we cannot | 
|  | * support jumbo frames on legacy VFs | 
|  | */ | 
|  | if ((pf_max_frame > ETH_FRAME_LEN) || | 
|  | (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN))) | 
|  | err = -EINVAL; | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* determine VF receive enable location */ | 
|  | vf_shift = vf % 32; | 
|  | reg_offset = vf / 32; | 
|  |  | 
|  | /* enable or disable receive depending on error */ | 
|  | vfre = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset)); | 
|  | if (err) | 
|  | vfre &= ~(1 << vf_shift); | 
|  | else | 
|  | vfre |= 1 << vf_shift; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), vfre); | 
|  |  | 
|  | if (err) { | 
|  | e_err(drv, "VF max_frame %d out of range\n", max_frame); | 
|  | return err; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* MTU < 68 is an error and causes problems on some kernels */ | 
|  | if (max_frame > IXGBE_MAX_JUMBO_FRAME_SIZE) { | 
|  | e_err(drv, "VF max_frame %d out of range\n", max_frame); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* pull current max frame size from hardware */ | 
|  | max_frs = IXGBE_READ_REG(hw, IXGBE_MAXFRS); | 
|  | max_frs &= IXGBE_MHADD_MFS_MASK; | 
|  | max_frs >>= IXGBE_MHADD_MFS_SHIFT; | 
|  |  | 
|  | if (max_frs < max_frame) { | 
|  | max_frs = max_frame << IXGBE_MHADD_MFS_SHIFT; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_MAXFRS, max_frs); | 
|  | } | 
|  |  | 
|  | e_info(hw, "VF requests change max MTU to %d\n", max_frame); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void ixgbe_set_vmolr(struct ixgbe_hw *hw, u32 vf, bool aupe) | 
|  | { | 
|  | u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf)); | 
|  | vmolr |= IXGBE_VMOLR_BAM; | 
|  | if (aupe) | 
|  | vmolr |= IXGBE_VMOLR_AUPE; | 
|  | else | 
|  | vmolr &= ~IXGBE_VMOLR_AUPE; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr); | 
|  | } | 
|  |  | 
|  | static void ixgbe_clear_vmvir(struct ixgbe_adapter *adapter, u32 vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  |  | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VMVIR(vf), 0); | 
|  | } | 
|  | static inline void ixgbe_vf_reset_event(struct ixgbe_adapter *adapter, u32 vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | struct vf_data_storage *vfinfo = &adapter->vfinfo[vf]; | 
|  | u8 num_tcs = netdev_get_num_tc(adapter->netdev); | 
|  |  | 
|  | /* add PF assigned VLAN or VLAN 0 */ | 
|  | ixgbe_set_vf_vlan(adapter, true, vfinfo->pf_vlan, vf); | 
|  |  | 
|  | /* reset offloads to defaults */ | 
|  | ixgbe_set_vmolr(hw, vf, !vfinfo->pf_vlan); | 
|  |  | 
|  | /* set outgoing tags for VFs */ | 
|  | if (!vfinfo->pf_vlan && !vfinfo->pf_qos && !num_tcs) { | 
|  | ixgbe_clear_vmvir(adapter, vf); | 
|  | } else { | 
|  | if (vfinfo->pf_qos || !num_tcs) | 
|  | ixgbe_set_vmvir(adapter, vfinfo->pf_vlan, | 
|  | vfinfo->pf_qos, vf); | 
|  | else | 
|  | ixgbe_set_vmvir(adapter, vfinfo->pf_vlan, | 
|  | adapter->default_up, vf); | 
|  |  | 
|  | if (vfinfo->spoofchk_enabled) | 
|  | hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf); | 
|  | } | 
|  |  | 
|  | /* reset multicast table array for vf */ | 
|  | adapter->vfinfo[vf].num_vf_mc_hashes = 0; | 
|  |  | 
|  | /* Flush and reset the mta with the new values */ | 
|  | ixgbe_set_rx_mode(adapter->netdev); | 
|  |  | 
|  | ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf); | 
|  |  | 
|  | /* reset VF api back to unknown */ | 
|  | adapter->vfinfo[vf].vf_api = ixgbe_mbox_api_10; | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_mac(struct ixgbe_adapter *adapter, | 
|  | int vf, unsigned char *mac_addr) | 
|  | { | 
|  | ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf); | 
|  | memcpy(adapter->vfinfo[vf].vf_mac_addresses, mac_addr, ETH_ALEN); | 
|  | ixgbe_add_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_macvlan(struct ixgbe_adapter *adapter, | 
|  | int vf, int index, unsigned char *mac_addr) | 
|  | { | 
|  | struct list_head *pos; | 
|  | struct vf_macvlans *entry; | 
|  |  | 
|  | if (index <= 1) { | 
|  | list_for_each(pos, &adapter->vf_mvs.l) { | 
|  | entry = list_entry(pos, struct vf_macvlans, l); | 
|  | if (entry->vf == vf) { | 
|  | entry->vf = -1; | 
|  | entry->free = true; | 
|  | entry->is_macvlan = false; | 
|  | ixgbe_del_mac_filter(adapter, | 
|  | entry->vf_macvlan, vf); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | /* | 
|  | * If index was zero then we were asked to clear the uc list | 
|  | * for the VF.  We're done. | 
|  | */ | 
|  | if (!index) | 
|  | return 0; | 
|  |  | 
|  | entry = NULL; | 
|  |  | 
|  | list_for_each(pos, &adapter->vf_mvs.l) { | 
|  | entry = list_entry(pos, struct vf_macvlans, l); | 
|  | if (entry->free) | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * If we traversed the entire list and didn't find a free entry | 
|  | * then we're out of space on the RAR table.  Also entry may | 
|  | * be NULL because the original memory allocation for the list | 
|  | * failed, which is not fatal but does mean we can't support | 
|  | * VF requests for MACVLAN because we couldn't allocate | 
|  | * memory for the list management required. | 
|  | */ | 
|  | if (!entry || !entry->free) | 
|  | return -ENOSPC; | 
|  |  | 
|  | entry->free = false; | 
|  | entry->is_macvlan = true; | 
|  | entry->vf = vf; | 
|  | memcpy(entry->vf_macvlan, mac_addr, ETH_ALEN); | 
|  |  | 
|  | ixgbe_add_mac_filter(adapter, mac_addr, vf); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = pci_get_drvdata(pdev); | 
|  | unsigned int vfn = (event_mask & 0x3f); | 
|  |  | 
|  | bool enable = ((event_mask & 0x10000000U) != 0); | 
|  |  | 
|  | if (enable) | 
|  | eth_zero_addr(adapter->vfinfo[vfn].vf_mac_addresses); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline void ixgbe_write_qde(struct ixgbe_adapter *adapter, u32 vf, | 
|  | u32 qde) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ]; | 
|  | u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask); | 
|  | int i; | 
|  |  | 
|  | for (i = vf * q_per_pool; i < ((vf + 1) * q_per_pool); i++) { | 
|  | u32 reg; | 
|  |  | 
|  | /* flush previous write */ | 
|  | IXGBE_WRITE_FLUSH(hw); | 
|  |  | 
|  | /* indicate to hardware that we want to set drop enable */ | 
|  | reg = IXGBE_QDE_WRITE | IXGBE_QDE_ENABLE; | 
|  | reg |= i <<  IXGBE_QDE_IDX_SHIFT; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_QDE, reg); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int ixgbe_vf_reset_msg(struct ixgbe_adapter *adapter, u32 vf) | 
|  | { | 
|  | struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ]; | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | unsigned char *vf_mac = adapter->vfinfo[vf].vf_mac_addresses; | 
|  | u32 reg, reg_offset, vf_shift; | 
|  | u32 msgbuf[4] = {0, 0, 0, 0}; | 
|  | u8 *addr = (u8 *)(&msgbuf[1]); | 
|  | u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask); | 
|  | int i; | 
|  |  | 
|  | e_info(probe, "VF Reset msg received from vf %d\n", vf); | 
|  |  | 
|  | /* reset the filters for the device */ | 
|  | ixgbe_vf_reset_event(adapter, vf); | 
|  |  | 
|  | /* set vf mac address */ | 
|  | if (!is_zero_ether_addr(vf_mac)) | 
|  | ixgbe_set_vf_mac(adapter, vf, vf_mac); | 
|  |  | 
|  | vf_shift = vf % 32; | 
|  | reg_offset = vf / 32; | 
|  |  | 
|  | /* enable transmit for vf */ | 
|  | reg = IXGBE_READ_REG(hw, IXGBE_VFTE(reg_offset)); | 
|  | reg |= 1 << vf_shift; | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFTE(reg_offset), reg); | 
|  |  | 
|  | /* force drop enable for all VF Rx queues */ | 
|  | ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE); | 
|  |  | 
|  | /* enable receive for vf */ | 
|  | reg = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset)); | 
|  | reg |= 1 << vf_shift; | 
|  | /* | 
|  | * The 82599 cannot support a mix of jumbo and non-jumbo PF/VFs. | 
|  | * For more info take a look at ixgbe_set_vf_lpe | 
|  | */ | 
|  | if (adapter->hw.mac.type == ixgbe_mac_82599EB) { | 
|  | struct net_device *dev = adapter->netdev; | 
|  | int pf_max_frame = dev->mtu + ETH_HLEN; | 
|  |  | 
|  | #ifdef CONFIG_FCOE | 
|  | if (dev->features & NETIF_F_FCOE_MTU) | 
|  | pf_max_frame = max_t(int, pf_max_frame, | 
|  | IXGBE_FCOE_JUMBO_FRAME_SIZE); | 
|  |  | 
|  | #endif /* CONFIG_FCOE */ | 
|  | if (pf_max_frame > ETH_FRAME_LEN) | 
|  | reg &= ~(1 << vf_shift); | 
|  | } | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), reg); | 
|  |  | 
|  | /* enable VF mailbox for further messages */ | 
|  | adapter->vfinfo[vf].clear_to_send = true; | 
|  |  | 
|  | /* Enable counting of spoofed packets in the SSVPC register */ | 
|  | reg = IXGBE_READ_REG(hw, IXGBE_VMECM(reg_offset)); | 
|  | reg |= (1 << vf_shift); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VMECM(reg_offset), reg); | 
|  |  | 
|  | /* | 
|  | * Reset the VFs TDWBAL and TDWBAH registers | 
|  | * which are not cleared by an FLR | 
|  | */ | 
|  | for (i = 0; i < q_per_pool; i++) { | 
|  | IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBAHn(q_per_pool, vf, i), 0); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBALn(q_per_pool, vf, i), 0); | 
|  | } | 
|  |  | 
|  | /* reply to reset with ack and vf mac address */ | 
|  | msgbuf[0] = IXGBE_VF_RESET; | 
|  | if (!is_zero_ether_addr(vf_mac)) { | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK; | 
|  | memcpy(addr, vf_mac, ETH_ALEN); | 
|  | } else { | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK; | 
|  | dev_warn(&adapter->pdev->dev, | 
|  | "VF %d has no MAC address assigned, you may have to assign one manually\n", | 
|  | vf); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Piggyback the multicast filter type so VF can compute the | 
|  | * correct vectors | 
|  | */ | 
|  | msgbuf[3] = hw->mac.mc_filter_type; | 
|  | ixgbe_write_mbx(hw, msgbuf, IXGBE_VF_PERMADDR_MSG_LEN, vf); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_mac_addr(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | u8 *new_mac = ((u8 *)(&msgbuf[1])); | 
|  |  | 
|  | if (!is_valid_ether_addr(new_mac)) { | 
|  | e_warn(drv, "VF %d attempted to set invalid mac\n", vf); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | if (adapter->vfinfo[vf].pf_set_mac && | 
|  | !ether_addr_equal(adapter->vfinfo[vf].vf_mac_addresses, new_mac)) { | 
|  | e_warn(drv, | 
|  | "VF %d attempted to override administratively set MAC address\n" | 
|  | "Reload the VF driver to resume operations\n", | 
|  | vf); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | return ixgbe_set_vf_mac(adapter, vf, new_mac) < 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_find_vlvf_entry(struct ixgbe_hw *hw, u32 vlan) | 
|  | { | 
|  | u32 vlvf; | 
|  | s32 regindex; | 
|  |  | 
|  | /* short cut the special case */ | 
|  | if (vlan == 0) | 
|  | return 0; | 
|  |  | 
|  | /* Search for the vlan id in the VLVF entries */ | 
|  | for (regindex = 1; regindex < IXGBE_VLVF_ENTRIES; regindex++) { | 
|  | vlvf = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex)); | 
|  | if ((vlvf & VLAN_VID_MASK) == vlan) | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* Return a negative value if not found */ | 
|  | if (regindex >= IXGBE_VLVF_ENTRIES) | 
|  | regindex = -1; | 
|  |  | 
|  | return regindex; | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_vlan_msg(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int add = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >> IXGBE_VT_MSGINFO_SHIFT; | 
|  | int vid = (msgbuf[1] & IXGBE_VLVF_VLANID_MASK); | 
|  | int err; | 
|  | s32 reg_ndx; | 
|  | u32 vlvf; | 
|  | u32 bits; | 
|  | u8 tcs = netdev_get_num_tc(adapter->netdev); | 
|  |  | 
|  | if (adapter->vfinfo[vf].pf_vlan || tcs) { | 
|  | e_warn(drv, | 
|  | "VF %d attempted to override administratively set VLAN configuration\n" | 
|  | "Reload the VF driver to resume operations\n", | 
|  | vf); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | if (add) | 
|  | adapter->vfinfo[vf].vlan_count++; | 
|  | else if (adapter->vfinfo[vf].vlan_count) | 
|  | adapter->vfinfo[vf].vlan_count--; | 
|  |  | 
|  | /* in case of promiscuous mode any VLAN filter set for a VF must | 
|  | * also have the PF pool added to it. | 
|  | */ | 
|  | if (add && adapter->netdev->flags & IFF_PROMISC) | 
|  | err = ixgbe_set_vf_vlan(adapter, add, vid, VMDQ_P(0)); | 
|  |  | 
|  | err = ixgbe_set_vf_vlan(adapter, add, vid, vf); | 
|  | if (!err && adapter->vfinfo[vf].spoofchk_enabled) | 
|  | hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf); | 
|  |  | 
|  | /* Go through all the checks to see if the VLAN filter should | 
|  | * be wiped completely. | 
|  | */ | 
|  | if (!add && adapter->netdev->flags & IFF_PROMISC) { | 
|  | reg_ndx = ixgbe_find_vlvf_entry(hw, vid); | 
|  | if (reg_ndx < 0) | 
|  | return err; | 
|  | vlvf = IXGBE_READ_REG(hw, IXGBE_VLVF(reg_ndx)); | 
|  | /* See if any other pools are set for this VLAN filter | 
|  | * entry other than the PF. | 
|  | */ | 
|  | if (VMDQ_P(0) < 32) { | 
|  | bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(reg_ndx * 2)); | 
|  | bits &= ~(1 << VMDQ_P(0)); | 
|  | bits |= IXGBE_READ_REG(hw, | 
|  | IXGBE_VLVFB(reg_ndx * 2) + 1); | 
|  | } else { | 
|  | bits = IXGBE_READ_REG(hw, | 
|  | IXGBE_VLVFB(reg_ndx * 2) + 1); | 
|  | bits &= ~(1 << (VMDQ_P(0) - 32)); | 
|  | bits |= IXGBE_READ_REG(hw, IXGBE_VLVFB(reg_ndx * 2)); | 
|  | } | 
|  |  | 
|  | /* If the filter was removed then ensure PF pool bit | 
|  | * is cleared if the PF only added itself to the pool | 
|  | * because the PF is in promiscuous mode. | 
|  | */ | 
|  | if ((vlvf & VLAN_VID_MASK) == vid && | 
|  | !test_bit(vid, adapter->active_vlans) && !bits) | 
|  | ixgbe_set_vf_vlan(adapter, add, vid, VMDQ_P(0)); | 
|  | } | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int ixgbe_set_vf_macvlan_msg(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | u8 *new_mac = ((u8 *)(&msgbuf[1])); | 
|  | int index = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >> | 
|  | IXGBE_VT_MSGINFO_SHIFT; | 
|  | int err; | 
|  |  | 
|  | if (adapter->vfinfo[vf].pf_set_mac && index > 0) { | 
|  | e_warn(drv, | 
|  | "VF %d requested MACVLAN filter but is administratively denied\n", | 
|  | vf); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | /* An non-zero index indicates the VF is setting a filter */ | 
|  | if (index) { | 
|  | if (!is_valid_ether_addr(new_mac)) { | 
|  | e_warn(drv, "VF %d attempted to set invalid mac\n", vf); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * If the VF is allowed to set MAC filters then turn off | 
|  | * anti-spoofing to avoid false positives. | 
|  | */ | 
|  | if (adapter->vfinfo[vf].spoofchk_enabled) | 
|  | ixgbe_ndo_set_vf_spoofchk(adapter->netdev, vf, false); | 
|  | } | 
|  |  | 
|  | err = ixgbe_set_vf_macvlan(adapter, vf, index, new_mac); | 
|  | if (err == -ENOSPC) | 
|  | e_warn(drv, | 
|  | "VF %d has requested a MACVLAN filter but there is no space for it\n", | 
|  | vf); | 
|  |  | 
|  | return err < 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | int api = msgbuf[1]; | 
|  |  | 
|  | switch (api) { | 
|  | case ixgbe_mbox_api_10: | 
|  | case ixgbe_mbox_api_11: | 
|  | adapter->vfinfo[vf].vf_api = api; | 
|  | return 0; | 
|  | default: | 
|  | break; | 
|  | } | 
|  |  | 
|  | e_info(drv, "VF %d requested invalid api version %u\n", vf, api); | 
|  |  | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter, | 
|  | u32 *msgbuf, u32 vf) | 
|  | { | 
|  | struct net_device *dev = adapter->netdev; | 
|  | struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ]; | 
|  | unsigned int default_tc = 0; | 
|  | u8 num_tcs = netdev_get_num_tc(dev); | 
|  |  | 
|  | /* verify the PF is supporting the correct APIs */ | 
|  | switch (adapter->vfinfo[vf].vf_api) { | 
|  | case ixgbe_mbox_api_20: | 
|  | case ixgbe_mbox_api_11: | 
|  | break; | 
|  | default: | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | /* only allow 1 Tx queue for bandwidth limiting */ | 
|  | msgbuf[IXGBE_VF_TX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask); | 
|  | msgbuf[IXGBE_VF_RX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask); | 
|  |  | 
|  | /* if TCs > 1 determine which TC belongs to default user priority */ | 
|  | if (num_tcs > 1) | 
|  | default_tc = netdev_get_prio_tc_map(dev, adapter->default_up); | 
|  |  | 
|  | /* notify VF of need for VLAN tag stripping, and correct queue */ | 
|  | if (num_tcs) | 
|  | msgbuf[IXGBE_VF_TRANS_VLAN] = num_tcs; | 
|  | else if (adapter->vfinfo[vf].pf_vlan || adapter->vfinfo[vf].pf_qos) | 
|  | msgbuf[IXGBE_VF_TRANS_VLAN] = 1; | 
|  | else | 
|  | msgbuf[IXGBE_VF_TRANS_VLAN] = 0; | 
|  |  | 
|  | /* notify VF of default queue */ | 
|  | msgbuf[IXGBE_VF_DEF_QUEUE] = default_tc; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf) | 
|  | { | 
|  | u32 mbx_size = IXGBE_VFMAILBOX_SIZE; | 
|  | u32 msgbuf[IXGBE_VFMAILBOX_SIZE]; | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | s32 retval; | 
|  |  | 
|  | retval = ixgbe_read_mbx(hw, msgbuf, mbx_size, vf); | 
|  |  | 
|  | if (retval) { | 
|  | pr_err("Error receiving message from VF\n"); | 
|  | return retval; | 
|  | } | 
|  |  | 
|  | /* this is a message we already processed, do nothing */ | 
|  | if (msgbuf[0] & (IXGBE_VT_MSGTYPE_ACK | IXGBE_VT_MSGTYPE_NACK)) | 
|  | return 0; | 
|  |  | 
|  | /* flush the ack before we write any messages back */ | 
|  | IXGBE_WRITE_FLUSH(hw); | 
|  |  | 
|  | if (msgbuf[0] == IXGBE_VF_RESET) | 
|  | return ixgbe_vf_reset_msg(adapter, vf); | 
|  |  | 
|  | /* | 
|  | * until the vf completes a virtual function reset it should not be | 
|  | * allowed to start any configuration. | 
|  | */ | 
|  | if (!adapter->vfinfo[vf].clear_to_send) { | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK; | 
|  | ixgbe_write_mbx(hw, msgbuf, 1, vf); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | switch ((msgbuf[0] & 0xFFFF)) { | 
|  | case IXGBE_VF_SET_MAC_ADDR: | 
|  | retval = ixgbe_set_vf_mac_addr(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_SET_MULTICAST: | 
|  | retval = ixgbe_set_vf_multicasts(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_SET_VLAN: | 
|  | retval = ixgbe_set_vf_vlan_msg(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_SET_LPE: | 
|  | retval = ixgbe_set_vf_lpe(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_SET_MACVLAN: | 
|  | retval = ixgbe_set_vf_macvlan_msg(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_API_NEGOTIATE: | 
|  | retval = ixgbe_negotiate_vf_api(adapter, msgbuf, vf); | 
|  | break; | 
|  | case IXGBE_VF_GET_QUEUES: | 
|  | retval = ixgbe_get_vf_queues(adapter, msgbuf, vf); | 
|  | break; | 
|  | default: | 
|  | e_err(drv, "Unhandled Msg %8.8x\n", msgbuf[0]); | 
|  | retval = IXGBE_ERR_MBX; | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* notify the VF of the results of what it sent us */ | 
|  | if (retval) | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK; | 
|  | else | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK; | 
|  |  | 
|  | msgbuf[0] |= IXGBE_VT_MSGTYPE_CTS; | 
|  |  | 
|  | ixgbe_write_mbx(hw, msgbuf, mbx_size, vf); | 
|  |  | 
|  | return retval; | 
|  | } | 
|  |  | 
|  | static void ixgbe_rcv_ack_from_vf(struct ixgbe_adapter *adapter, u32 vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 msg = IXGBE_VT_MSGTYPE_NACK; | 
|  |  | 
|  | /* if device isn't clear to send it shouldn't be reading either */ | 
|  | if (!adapter->vfinfo[vf].clear_to_send) | 
|  | ixgbe_write_mbx(hw, &msg, 1, vf); | 
|  | } | 
|  |  | 
|  | void ixgbe_msg_task(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 vf; | 
|  |  | 
|  | for (vf = 0; vf < adapter->num_vfs; vf++) { | 
|  | /* process any reset requests */ | 
|  | if (!ixgbe_check_for_rst(hw, vf)) | 
|  | ixgbe_vf_reset_event(adapter, vf); | 
|  |  | 
|  | /* process any messages pending */ | 
|  | if (!ixgbe_check_for_msg(hw, vf)) | 
|  | ixgbe_rcv_msg_from_vf(adapter, vf); | 
|  |  | 
|  | /* process any acks */ | 
|  | if (!ixgbe_check_for_ack(hw, vf)) | 
|  | ixgbe_rcv_ack_from_vf(adapter, vf); | 
|  | } | 
|  | } | 
|  |  | 
|  | void ixgbe_disable_tx_rx(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  |  | 
|  | /* disable transmit and receive for all vfs */ | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFTE(0), 0); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFTE(1), 0); | 
|  |  | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFRE(0), 0); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_VFRE(1), 0); | 
|  | } | 
|  |  | 
|  | void ixgbe_ping_all_vfs(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 ping; | 
|  | int i; | 
|  |  | 
|  | for (i = 0 ; i < adapter->num_vfs; i++) { | 
|  | ping = IXGBE_PF_CONTROL_MSG; | 
|  | if (adapter->vfinfo[i].clear_to_send) | 
|  | ping |= IXGBE_VT_MSGTYPE_CTS; | 
|  | ixgbe_write_mbx(hw, &ping, 1, i); | 
|  | } | 
|  | } | 
|  |  | 
|  | int ixgbe_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = netdev_priv(netdev); | 
|  | if (!is_valid_ether_addr(mac) || (vf >= adapter->num_vfs)) | 
|  | return -EINVAL; | 
|  | adapter->vfinfo[vf].pf_set_mac = true; | 
|  | dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n", mac, vf); | 
|  | dev_info(&adapter->pdev->dev, "Reload the VF driver to make this" | 
|  | " change effective."); | 
|  | if (test_bit(__IXGBE_DOWN, &adapter->state)) { | 
|  | dev_warn(&adapter->pdev->dev, "The VF MAC address has been set," | 
|  | " but the PF device is not up.\n"); | 
|  | dev_warn(&adapter->pdev->dev, "Bring the PF device up before" | 
|  | " attempting to use the VF device.\n"); | 
|  | } | 
|  | return ixgbe_set_vf_mac(adapter, vf, mac); | 
|  | } | 
|  |  | 
|  | static int ixgbe_enable_port_vlan(struct ixgbe_adapter *adapter, int vf, | 
|  | u16 vlan, u8 qos) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int err = 0; | 
|  |  | 
|  | if (adapter->vfinfo[vf].pf_vlan) | 
|  | err = ixgbe_set_vf_vlan(adapter, false, | 
|  | adapter->vfinfo[vf].pf_vlan, | 
|  | vf); | 
|  | if (err) | 
|  | goto out; | 
|  | ixgbe_set_vmvir(adapter, vlan, qos, vf); | 
|  | ixgbe_set_vmolr(hw, vf, false); | 
|  | if (adapter->vfinfo[vf].spoofchk_enabled) | 
|  | hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf); | 
|  | adapter->vfinfo[vf].vlan_count++; | 
|  |  | 
|  | /* enable hide vlan on X550 */ | 
|  | if (hw->mac.type >= ixgbe_mac_X550) | 
|  | ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE | | 
|  | IXGBE_QDE_HIDE_VLAN); | 
|  |  | 
|  | adapter->vfinfo[vf].pf_vlan = vlan; | 
|  | adapter->vfinfo[vf].pf_qos = qos; | 
|  | dev_info(&adapter->pdev->dev, | 
|  | "Setting VLAN %d, QOS 0x%x on VF %d\n", vlan, qos, vf); | 
|  | if (test_bit(__IXGBE_DOWN, &adapter->state)) { | 
|  | dev_warn(&adapter->pdev->dev, | 
|  | "The VF VLAN has been set, but the PF device is not up.\n"); | 
|  | dev_warn(&adapter->pdev->dev, | 
|  | "Bring the PF device up before attempting to use the VF device.\n"); | 
|  | } | 
|  |  | 
|  | out: | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int ixgbe_disable_port_vlan(struct ixgbe_adapter *adapter, int vf) | 
|  | { | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | int err; | 
|  |  | 
|  | err = ixgbe_set_vf_vlan(adapter, false, | 
|  | adapter->vfinfo[vf].pf_vlan, vf); | 
|  | ixgbe_clear_vmvir(adapter, vf); | 
|  | ixgbe_set_vmolr(hw, vf, true); | 
|  | hw->mac.ops.set_vlan_anti_spoofing(hw, false, vf); | 
|  | if (adapter->vfinfo[vf].vlan_count) | 
|  | adapter->vfinfo[vf].vlan_count--; | 
|  | adapter->vfinfo[vf].pf_vlan = 0; | 
|  | adapter->vfinfo[vf].pf_qos = 0; | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | int ixgbe_ndo_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan, u8 qos) | 
|  | { | 
|  | int err = 0; | 
|  | struct ixgbe_adapter *adapter = netdev_priv(netdev); | 
|  |  | 
|  | if ((vf >= adapter->num_vfs) || (vlan > 4095) || (qos > 7)) | 
|  | return -EINVAL; | 
|  | if (vlan || qos) { | 
|  | /* Check if there is already a port VLAN set, if so | 
|  | * we have to delete the old one first before we | 
|  | * can set the new one.  The usage model had | 
|  | * previously assumed the user would delete the | 
|  | * old port VLAN before setting a new one but this | 
|  | * is not necessarily the case. | 
|  | */ | 
|  | if (adapter->vfinfo[vf].pf_vlan) | 
|  | err = ixgbe_disable_port_vlan(adapter, vf); | 
|  | if (err) | 
|  | goto out; | 
|  | err = ixgbe_enable_port_vlan(adapter, vf, vlan, qos); | 
|  | } else { | 
|  | err = ixgbe_disable_port_vlan(adapter, vf); | 
|  | } | 
|  |  | 
|  | out: | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int ixgbe_link_mbps(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | switch (adapter->link_speed) { | 
|  | case IXGBE_LINK_SPEED_100_FULL: | 
|  | return 100; | 
|  | case IXGBE_LINK_SPEED_1GB_FULL: | 
|  | return 1000; | 
|  | case IXGBE_LINK_SPEED_10GB_FULL: | 
|  | return 10000; | 
|  | default: | 
|  | return 0; | 
|  | } | 
|  | } | 
|  |  | 
|  | static void ixgbe_set_vf_rate_limit(struct ixgbe_adapter *adapter, int vf) | 
|  | { | 
|  | struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ]; | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 bcnrc_val = 0; | 
|  | u16 queue, queues_per_pool; | 
|  | u16 tx_rate = adapter->vfinfo[vf].tx_rate; | 
|  |  | 
|  | if (tx_rate) { | 
|  | /* start with base link speed value */ | 
|  | bcnrc_val = adapter->vf_rate_link_speed; | 
|  |  | 
|  | /* Calculate the rate factor values to set */ | 
|  | bcnrc_val <<= IXGBE_RTTBCNRC_RF_INT_SHIFT; | 
|  | bcnrc_val /= tx_rate; | 
|  |  | 
|  | /* clear everything but the rate factor */ | 
|  | bcnrc_val &= IXGBE_RTTBCNRC_RF_INT_MASK | | 
|  | IXGBE_RTTBCNRC_RF_DEC_MASK; | 
|  |  | 
|  | /* enable the rate scheduler */ | 
|  | bcnrc_val |= IXGBE_RTTBCNRC_RS_ENA; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Set global transmit compensation time to the MMW_SIZE in RTTBCNRM | 
|  | * register. Typically MMW_SIZE=0x014 if 9728-byte jumbo is supported | 
|  | * and 0x004 otherwise. | 
|  | */ | 
|  | switch (hw->mac.type) { | 
|  | case ixgbe_mac_82599EB: | 
|  | IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x4); | 
|  | break; | 
|  | case ixgbe_mac_X540: | 
|  | IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x14); | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* determine how many queues per pool based on VMDq mask */ | 
|  | queues_per_pool = __ALIGN_MASK(1, ~vmdq->mask); | 
|  |  | 
|  | /* write value for all Tx queues belonging to VF */ | 
|  | for (queue = 0; queue < queues_per_pool; queue++) { | 
|  | unsigned int reg_idx = (vf * queues_per_pool) + queue; | 
|  |  | 
|  | IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, reg_idx); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, bcnrc_val); | 
|  | } | 
|  | } | 
|  |  | 
|  | void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | /* VF Tx rate limit was not set */ | 
|  | if (!adapter->vf_rate_link_speed) | 
|  | return; | 
|  |  | 
|  | if (ixgbe_link_mbps(adapter) != adapter->vf_rate_link_speed) { | 
|  | adapter->vf_rate_link_speed = 0; | 
|  | dev_info(&adapter->pdev->dev, | 
|  | "Link speed has been changed. VF Transmit rate is disabled\n"); | 
|  | } | 
|  |  | 
|  | for (i = 0; i < adapter->num_vfs; i++) { | 
|  | if (!adapter->vf_rate_link_speed) | 
|  | adapter->vfinfo[i].tx_rate = 0; | 
|  |  | 
|  | ixgbe_set_vf_rate_limit(adapter, i); | 
|  | } | 
|  | } | 
|  |  | 
|  | int ixgbe_ndo_set_vf_bw(struct net_device *netdev, int vf, int min_tx_rate, | 
|  | int max_tx_rate) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = netdev_priv(netdev); | 
|  | int link_speed; | 
|  |  | 
|  | /* verify VF is active */ | 
|  | if (vf >= adapter->num_vfs) | 
|  | return -EINVAL; | 
|  |  | 
|  | /* verify link is up */ | 
|  | if (!adapter->link_up) | 
|  | return -EINVAL; | 
|  |  | 
|  | /* verify we are linked at 10Gbps */ | 
|  | link_speed = ixgbe_link_mbps(adapter); | 
|  | if (link_speed != 10000) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (min_tx_rate) | 
|  | return -EINVAL; | 
|  |  | 
|  | /* rate limit cannot be less than 10Mbs or greater than link speed */ | 
|  | if (max_tx_rate && ((max_tx_rate <= 10) || (max_tx_rate > link_speed))) | 
|  | return -EINVAL; | 
|  |  | 
|  | /* store values */ | 
|  | adapter->vf_rate_link_speed = link_speed; | 
|  | adapter->vfinfo[vf].tx_rate = max_tx_rate; | 
|  |  | 
|  | /* update hardware configuration */ | 
|  | ixgbe_set_vf_rate_limit(adapter, vf); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | int ixgbe_ndo_set_vf_spoofchk(struct net_device *netdev, int vf, bool setting) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = netdev_priv(netdev); | 
|  | int vf_target_reg = vf >> 3; | 
|  | int vf_target_shift = vf % 8; | 
|  | struct ixgbe_hw *hw = &adapter->hw; | 
|  | u32 regval; | 
|  |  | 
|  | if (vf >= adapter->num_vfs) | 
|  | return -EINVAL; | 
|  |  | 
|  | adapter->vfinfo[vf].spoofchk_enabled = setting; | 
|  |  | 
|  | regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); | 
|  | regval &= ~(1 << vf_target_shift); | 
|  | regval |= (setting << vf_target_shift); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval); | 
|  |  | 
|  | if (adapter->vfinfo[vf].vlan_count) { | 
|  | vf_target_shift += IXGBE_SPOOF_VLANAS_SHIFT; | 
|  | regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); | 
|  | regval &= ~(1 << vf_target_shift); | 
|  | regval |= (setting << vf_target_shift); | 
|  | IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | int ixgbe_ndo_get_vf_config(struct net_device *netdev, | 
|  | int vf, struct ifla_vf_info *ivi) | 
|  | { | 
|  | struct ixgbe_adapter *adapter = netdev_priv(netdev); | 
|  | if (vf >= adapter->num_vfs) | 
|  | return -EINVAL; | 
|  | ivi->vf = vf; | 
|  | memcpy(&ivi->mac, adapter->vfinfo[vf].vf_mac_addresses, ETH_ALEN); | 
|  | ivi->max_tx_rate = adapter->vfinfo[vf].tx_rate; | 
|  | ivi->min_tx_rate = 0; | 
|  | ivi->vlan = adapter->vfinfo[vf].pf_vlan; | 
|  | ivi->qos = adapter->vfinfo[vf].pf_qos; | 
|  | ivi->spoofchk = adapter->vfinfo[vf].spoofchk_enabled; | 
|  | return 0; | 
|  | } |