| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| |
| #include "x1e80100.dtsi" |
| #include "x1e80100-pmics.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. X1E80100 CRD"; |
| compatible = "qcom,x1e80100-crd", "qcom,x1e80100"; |
| |
| aliases { |
| serial0 = &uart21; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9385-codec"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcd_default>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_l15b_1p8>; |
| vdd-rxtx-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l15b_1p8>; |
| vdd-mic-bias-supply = <&vreg_bob1>; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,x1e80100-pmic-glink", |
| "qcom,sm8550-pmic-glink", |
| "qcom,pmic-glink"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, |
| <&tlmm 123 GPIO_ACTIVE_HIGH>, |
| <&tlmm 125 GPIO_ACTIVE_HIGH>; |
| |
| /* Left-side rear port */ |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss0_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss0_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* Left-side front port */ |
| connector@1 { |
| compatible = "usb-c-connector"; |
| reg = <1>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss1_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss1_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* Right-side port */ |
| connector@2 { |
| compatible = "usb-c-connector"; |
| reg = <2>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss2_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss2_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss2_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss2_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| size = <0x0 0x8000000>; |
| reusable; |
| linux,cma-default; |
| }; |
| }; |
| |
| sound { |
| compatible = "qcom,x1e80100-sndcard"; |
| model = "X1E80100-CRD"; |
| audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT", |
| "TwitterLeft IN", "WSA WSA_SPK2 OUT", |
| "WooferRight IN", "WSA2 WSA_SPK2 OUT", |
| "TwitterRight IN", "WSA2 WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC2", "MIC BIAS2", |
| "VA DMIC0", "MIC BIAS3", |
| "VA DMIC1", "MIC BIAS3", |
| "VA DMIC2", "MIC BIAS1", |
| "VA DMIC3", "MIC BIAS1", |
| "VA DMIC0", "VA MIC BIAS3", |
| "VA DMIC1", "VA MIC BIAS3", |
| "VA DMIC2", "VA MIC BIAS1", |
| "VA DMIC3", "VA MIC BIAS1", |
| "TX SWR_INPUT1", "ADC2_OUTPUT"; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_woofer>, <&left_tweeter>, |
| <&swr0 0>, <&lpass_wsamacro 0>, |
| <&right_woofer>, <&right_tweeter>, |
| <&swr3 0>, <&lpass_wsa2macro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&lpass_vamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vreg_edp_3p3: regulator-edp-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_EDP_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&edp_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_nvme: regulator-nvme { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_NVME_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&nvme_reg_en>; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8550-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-bob1-supply = <&vph_pwr>; |
| vdd-bob2-supply = <&vph_pwr>; |
| vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| vdd-l5-l16-supply = <&vreg_bob1>; |
| vdd-l6-l7-supply = <&vreg_bob2>; |
| vdd-l8-l9-supply = <&vreg_bob1>; |
| vdd-l12-supply = <&vreg_s5j_1p2>; |
| vdd-l15-supply = <&vreg_s4c_1p8>; |
| vdd-l17-supply = <&vreg_bob2>; |
| |
| vreg_bob1: bob1 { |
| regulator-name = "vreg_bob1"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob2: bob2 { |
| regulator-name = "vreg_bob2"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1b_1p8: ldo1 { |
| regulator-name = "vreg_l1b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p0: ldo2 { |
| regulator-name = "vreg_l2b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4b_1p8: ldo4 { |
| regulator-name = "vreg_l4b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b_3p0: ldo5 { |
| regulator-name = "vreg_l5b_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p8: ldo6 { |
| regulator-name = "vreg_l6b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_2p8: ldo7 { |
| regulator-name = "vreg_l7b_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b_3p0: ldo8 { |
| regulator-name = "vreg_l8b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b_2p9: ldo9 { |
| regulator-name = "vreg_l9b_2p9"; |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10b_1p8: ldo10 { |
| regulator-name = "vreg_l10b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b_1p2: ldo12 { |
| regulator-name = "vreg_l12b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_3p0: ldo13 { |
| regulator-name = "vreg_l13b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_3p0: ldo14 { |
| regulator-name = "vreg_l14b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_1p8: ldo15 { |
| regulator-name = "vreg_l15b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16b_2p9: ldo16 { |
| regulator-name = "vreg_l16b_2p9"; |
| regulator-min-microvolt = <2912000>; |
| regulator-max-microvolt = <2912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b_2p5: ldo17 { |
| regulator-name = "vreg_l17b_2p5"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <2504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-l1-supply = <&vreg_s5j_1p2>; |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_s4c_1p8: smps4 { |
| regulator-name = "vreg_s4c_1p8"; |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1c_1p2: ldo1 { |
| regulator-name = "vreg_l1c_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c_0p8: ldo2 { |
| regulator-name = "vreg_l2c_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_0p8: ldo3 { |
| regulator-name = "vreg_l3c_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "d"; |
| |
| vdd-l1-supply = <&vreg_s1f_0p7>; |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s4c_1p8>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_l1d_0p8: ldo1 { |
| regulator-name = "vreg_l1d_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2d_0p9: ldo2 { |
| regulator-name = "vreg_l2d_0p9"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3d_1p8: ldo3 { |
| regulator-name = "vreg_l3d_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s5j_1p2>; |
| |
| vreg_l2e_0p8: ldo2 { |
| regulator-name = "vreg_l2e_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3e_1p2: ldo3 { |
| regulator-name = "vreg_l3e_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-4 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "f"; |
| |
| vdd-l1-supply = <&vreg_s5j_1p2>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s5j_1p2>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_s1f_0p7: smps1 { |
| regulator-name = "vreg_s1f_0p7"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1f_1p0: ldo1 { |
| regulator-name = "vreg_l1f_1p0"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2f_1p0: ldo2 { |
| regulator-name = "vreg_l2f_1p0"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3f_1p0: ldo3 { |
| regulator-name = "vreg_l3f_1p0"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-6 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "i"; |
| |
| vdd-l1-supply = <&vreg_s4c_1p8>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| |
| vreg_s1i_0p9: smps1 { |
| regulator-name = "vreg_s1i_0p9"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s2i_1p0: smps2 { |
| regulator-name = "vreg_s2i_1p0"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1i_1p8: ldo1 { |
| regulator-name = "vreg_l1i_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2i_1p2: ldo2 { |
| regulator-name = "vreg_l2i_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3i_0p8: ldo3 { |
| regulator-name = "vreg_l3i_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-7 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "j"; |
| |
| vdd-l1-supply = <&vreg_s1f_0p7>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s5-supply = <&vph_pwr>; |
| |
| vreg_s5j_1p2: smps5 { |
| regulator-name = "vreg_s5j_1p2"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1j_0p8: ldo1 { |
| regulator-name = "vreg_l1j_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2j_1p2: ldo2 { |
| regulator-name = "vreg_l2j_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3j_0p8: ldo3 { |
| regulator-name = "vreg_l3j_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/x1e80100/gen70500_zap.mbn"; |
| }; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| touchpad@15 { |
| compatible = "hid-over-i2c"; |
| reg = <0x15>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&tpad_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| |
| keyboard@3a { |
| compatible = "hid-over-i2c"; |
| reg = <0x3a>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&kybd_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| }; |
| |
| &i2c8 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| touchscreen@10 { |
| compatible = "hid-over-i2c"; |
| reg = <0x10>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&ts0_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &lpass_tlmm { |
| spkr_01_sd_n_active: spkr-01-sd-n-active-state { |
| pins = "gpio12"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| spkr_23_sd_n_active: spkr-23-sd-n-active-state { |
| pins = "gpio13"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &lpass_vamacro { |
| pinctrl-0 = <&dmic01_default>, <&dmic23_default>; |
| pinctrl-names = "default"; |
| |
| vdd-micb-supply = <&vreg_l1b_1p8>; |
| qcom,dmic-sample-rate = <4800000>; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dp3 { |
| compatible = "qcom,x1e80100-dp"; |
| /delete-property/ #sound-dai-cells; |
| |
| status = "okay"; |
| |
| aux-bus { |
| panel { |
| compatible = "samsung,atna45af01", "samsung,atna33xc20"; |
| enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>; |
| power-supply = <&vreg_edp_3p3>; |
| |
| pinctrl-0 = <&edp_bl_en>; |
| pinctrl-names = "default"; |
| |
| port { |
| edp_panel_in: endpoint { |
| remote-endpoint = <&mdss_dp3_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| mdss_dp3_out: endpoint { |
| data-lanes = <0 1 2 3>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| |
| remote-endpoint = <&edp_panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dp3_phy { |
| vdda-phy-supply = <&vreg_l3j_0p8>; |
| vdda-pll-supply = <&vreg_l2j_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4 { |
| perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&pcie4_default>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4_phy { |
| vdda-phy-supply = <&vreg_l3i_0p8>; |
| vdda-pll-supply = <&vreg_l3e_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie6a { |
| perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_nvme>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie6a_default>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie6a_phy { |
| vdda-phy-supply = <&vreg_l1d_0p8>; |
| vdda-pll-supply = <&vreg_l2j_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pmc8380_3_gpios { |
| edp_bl_en: edp-bl-en-state { |
| pins = "gpio4"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| input-disable; |
| output-enable; |
| }; |
| }; |
| |
| &qupv3_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_1 { |
| status = "okay"; |
| }; |
| |
| &qupv3_2 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/x1e80100/adsp.mbn", |
| "qcom/x1e80100/adsp_dtb.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/x1e80100/cdsp.mbn", |
| "qcom/x1e80100/cdsp_dtb.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &smb2360_0_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d_1p8>; |
| vdd3-supply = <&vreg_l2b_3p0>; |
| }; |
| |
| &smb2360_1_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d_1p8>; |
| vdd3-supply = <&vreg_l14b_3p0>; |
| }; |
| |
| &smb2360_2_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d_1p8>; |
| vdd3-supply = <&vreg_l8b_3p0>; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>; |
| pinctrl-names = "default"; |
| |
| /* WSA8845, Left Woofer */ |
| left_woofer: speaker@0,0 { |
| compatible = "sdw20217020400"; |
| reg = <0 0>; |
| reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "WooferLeft"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l12b_1p2>; |
| }; |
| |
| /* WSA8845, Left Tweeter */ |
| left_tweeter: speaker@0,1 { |
| compatible = "sdw20217020400"; |
| reg = <0 1>; |
| reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "TwitterLeft"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l12b_1p2>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| /* WCD9385 RX */ |
| wcd_rx: codec@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| /* WCD9385 TX */ |
| wcd_tx: codec@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <2 2 3 4>; |
| }; |
| }; |
| |
| &swr3 { |
| status = "okay"; |
| |
| pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>; |
| pinctrl-names = "default"; |
| |
| /* WSA8845, Right Woofer */ |
| right_woofer: speaker@0,0 { |
| compatible = "sdw20217020400"; |
| reg = <0 0>; |
| reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "WooferRight"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l12b_1p2>; |
| }; |
| |
| /* WSA8845, Right Tweeter */ |
| right_tweeter: speaker@0,1 { |
| compatible = "sdw20217020400"; |
| reg = <0 1>; |
| reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "TwitterRight"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l12b_1p2>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <34 2>, /* Unused */ |
| <44 4>, /* SPI (TPM) */ |
| <238 1>; /* UFS Reset */ |
| |
| edp_reg_en: edp-reg-en-state { |
| pins = "gpio70"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| kybd_default: kybd-default-state { |
| pins = "gpio67"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| nvme_reg_en: nvme-reg-en-state { |
| pins = "gpio18"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| pcie4_default: pcie4-default-state { |
| clkreq-n-pins { |
| pins = "gpio147"; |
| function = "pcie4_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio146"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio148"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie6a_default: pcie6a-default-state { |
| clkreq-n-pins { |
| pins = "gpio153"; |
| function = "pcie6a_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio152"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio154"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| tpad_default: tpad-default-state { |
| pins = "gpio3"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| ts0_default: ts0-default-state { |
| int-n-pins { |
| pins = "gpio51"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| reset-n-pins { |
| pins = "gpio48"; |
| function = "gpio"; |
| output-high; |
| drive-strength = <16>; |
| }; |
| }; |
| |
| wcd_default: wcd-reset-n-active-state { |
| pins = "gpio191"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &uart21 { |
| compatible = "qcom,geni-debug-uart"; |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_hsphy { |
| vdd-supply = <&vreg_l3j_0p8>; |
| vdda12-supply = <&vreg_l2j_1p2>; |
| |
| phys = <&smb2360_0_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_qmpphy { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l1j_0p8>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss0_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss0_hs_in>; |
| }; |
| |
| &usb_1_ss0_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss0_ss_in>; |
| }; |
| |
| &usb_1_ss1_hsphy { |
| vdd-supply = <&vreg_l3j_0p8>; |
| vdda12-supply = <&vreg_l2j_1p2>; |
| |
| phys = <&smb2360_1_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_qmpphy { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l2d_0p9>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss1_hs_in>; |
| }; |
| |
| &usb_1_ss1_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss1_ss_in>; |
| }; |
| |
| &usb_1_ss2_hsphy { |
| vdd-supply = <&vreg_l3j_0p8>; |
| vdda12-supply = <&vreg_l2j_1p2>; |
| |
| phys = <&smb2360_2_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss2_qmpphy { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l2d_0p9>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss2 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss2_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss2_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss2_hs_in>; |
| }; |
| |
| &usb_1_ss2_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss2_ss_in>; |
| }; |
