blob: 5a19da9313ae6c205debc920878f08435228118d [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+ OR MIT
/*
* Copyright 2014-2020 Toradex
*/
/ {
chosen {
stdout-path = "serial0:115200n8";
};
clk16m: clk16m {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <16000000>;
};
panel: panel {
compatible = "edt,et057090dhu";
backlight = <&bl>;
port {
panel_in: endpoint {
remote-endpoint = <&dcu_out>;
};
};
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_5v0: regulator-5v0 {
compatible = "regulator-fixed";
regulator-name = "5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
reg_usbh_vbus: regulator-usbh-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1_reg>;
regulator-name = "VCC_USB[1-4]";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio2 19 GPIO_ACTIVE_LOW>; /* USBH_PEN resp. USBH_P_EN */
vin-supply = <&reg_5v0>;
};
};
&bl {
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
power-supply = <&reg_3v3>;
status = "okay";
};
&dcu0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dcu0_1>;
status = "okay";
port {
dcu_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
&dspi1 {
status = "okay";
mcp2515can: can@0 {
compatible = "microchip,mcp2515";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can_int>;
reg = <0>;
clocks = <&clk16m>;
spi-max-frequency = <10000000>;
interrupt-parent = <&gpio1>;
interrupts = <11 IRQ_TYPE_EDGE_RISING>;
};
};
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
bus-width = <4>;
status = "okay";
};
&fec1 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec1>;
status = "okay";
};
&i2c0 {
status = "okay";
/* M41T0M6 real time clock on carrier board */
rtc: rtc@68 {
compatible = "st,m41t0";
reg = <0x68>;
};
};
&pwm0 {
status = "okay";
};
&pwm1 {
status = "okay";
};
&reg_module_3v3 {
vin-supply = <&reg_3v3>;
};
&tcon0 {
status = "okay";
};
&uart0 {
status = "okay";
};
&uart1 {
status = "okay";
};
&uart2 {
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_usbh_vbus>;
};
&iomuxc {
vf610-colibri {
pinctrl_can_int: can_int {
fsl,pins = <
VF610_PAD_PTB21__GPIO_43 0x22ed
>;
};
};
};