| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (c) 2018 Texas Instruments |
| // MMC IOdelay values for TI's DRA76x and AM576x SoCs. |
| // Author: Sekhar Nori <nsekhar@ti.com> |
| |
| /* |
| * Rules for modifying this file: |
| * a) Update of this file should typically correspond to a datamanual revision. |
| * Datamanual revision that was used should be updated in comment below. |
| * If there is no update to datamanual, do not update the values. If you |
| * need to use values different from that recommended by the datamanual |
| * for your design, then you should consider adding values to the device- |
| * -tree file for your board directly. |
| * b) We keep the mode names as close to the datamanual as possible. So |
| * if the manual calls a mode, DDR50, or DDR or DDR 1.8v or DDR 3.3v, |
| * we follow that in code too. |
| * c) If the values change between multiple revisions of silicon, we add |
| * a revision tag to both the new and old entry. Use 'rev11' for PG 1.1, |
| * 'rev20' for PG 2.0 and so on. |
| * d) The node name and node label should be the exact same string. This is |
| * to curb naming creativity and achieve consistency. |
| * |
| * Datamanual Revisions: |
| * |
| * DRA76x Silicon Revision 1.0: SPRS993E, Revised December 2018 |
| * |
| */ |
| |
| &dra7_pmx_core { |
| mmc1_pins_default: mmc1_pins_default { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ |
| DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ |
| DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ |
| DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ |
| DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ |
| DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ |
| >; |
| }; |
| |
| mmc1_pins_hs: mmc1_pins_hs { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_clk.clk */ |
| DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_cmd.cmd */ |
| DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat0.dat0 */ |
| DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat1.dat1 */ |
| DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat2.dat2 */ |
| DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat3.dat3 */ |
| >; |
| }; |
| |
| mmc1_pins_sdr50: mmc1_pins_sdr50 { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_clk.clk */ |
| DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_cmd.cmd */ |
| DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_dat0.dat0 */ |
| DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_dat1.dat1 */ |
| DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_dat2.dat2 */ |
| DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0) /* mmc1_dat3.dat3 */ |
| >; |
| }; |
| |
| mmc1_pins_ddr50: mmc1_pins_ddr50 { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_clk.clk */ |
| DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_cmd.cmd */ |
| DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_dat0.dat0 */ |
| DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_dat1.dat1 */ |
| DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_dat2.dat2 */ |
| DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0) /* mmc1_dat3.dat3 */ |
| >; |
| }; |
| |
| mmc2_pins_default: mmc2_pins_default { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ |
| DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ |
| DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ |
| DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ |
| DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ |
| DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ |
| DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ |
| DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ |
| DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ |
| DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ |
| >; |
| }; |
| |
| mmc2_pins_hs200: mmc2_pins_hs200 { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */ |
| DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ |
| DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ |
| DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ |
| DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ |
| DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ |
| DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ |
| DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ |
| DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ |
| DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ |
| >; |
| }; |
| |
| mmc3_pins_default: mmc3_pins_default { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */ |
| DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */ |
| DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */ |
| DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */ |
| DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */ |
| DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */ |
| >; |
| }; |
| |
| mmc4_pins_hs: mmc4_pins_hs { |
| pinctrl-single,pins = < |
| DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */ |
| DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */ |
| DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */ |
| DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */ |
| DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */ |
| DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */ |
| >; |
| }; |
| }; |
| |
| &dra7_iodelay_core { |
| |
| /* Corresponds to MMC1_DDR_MANUAL1 in datamanual */ |
| mmc1_iodelay_ddr_conf: mmc1_iodelay_ddr_conf { |
| pinctrl-pin-array = < |
| 0x618 A_DELAY_PS(489) G_DELAY_PS(0) /* CFG_MMC1_CLK_IN */ |
| 0x624 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_CMD_IN */ |
| 0x630 A_DELAY_PS(374) G_DELAY_PS(0) /* CFG_MMC1_DAT0_IN */ |
| 0x63c A_DELAY_PS(31) G_DELAY_PS(0) /* CFG_MMC1_DAT1_IN */ |
| 0x648 A_DELAY_PS(56) G_DELAY_PS(0) /* CFG_MMC1_DAT2_IN */ |
| 0x654 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT3_IN */ |
| 0x620 A_DELAY_PS(1355) G_DELAY_PS(0) /* CFG_MMC1_CLK_OUT */ |
| 0x628 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_CMD_OEN */ |
| 0x62c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_CMD_OUT */ |
| 0x634 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT0_OEN */ |
| 0x638 A_DELAY_PS(0) G_DELAY_PS(4) /* CFG_MMC1_DAT0_OUT */ |
| 0x640 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT1_OEN */ |
| 0x644 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT1_OUT */ |
| 0x64c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT2_OEN */ |
| 0x650 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT2_OUT */ |
| 0x658 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT3_OEN */ |
| 0x65c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT3_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC1_SDR104_MANUAL1 in datamanual */ |
| mmc1_iodelay_sdr104_conf: mmc1_iodelay_sdr104_conf { |
| pinctrl-pin-array = < |
| 0x620 A_DELAY_PS(892) G_DELAY_PS(0) /* CFG_MMC1_CLK_OUT */ |
| 0x628 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_CMD_OEN */ |
| 0x62c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_CMD_OUT */ |
| 0x634 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT0_OEN */ |
| 0x638 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT0_OUT */ |
| 0x640 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT1_OEN */ |
| 0x644 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT1_OUT */ |
| 0x64c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT2_OEN */ |
| 0x650 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT2_OUT */ |
| 0x658 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT3_OEN */ |
| 0x65c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC1_DAT3_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC2_HS200_MANUAL1 in datamanual */ |
| mmc2_iodelay_hs200_conf: mmc2_iodelay_hs200_conf { |
| pinctrl-pin-array = < |
| 0x190 A_DELAY_PS(384) G_DELAY_PS(0) /* CFG_GPMC_A19_OEN */ |
| 0x194 A_DELAY_PS(350) G_DELAY_PS(174) /* CFG_GPMC_A19_OUT */ |
| 0x1a8 A_DELAY_PS(410) G_DELAY_PS(0) /* CFG_GPMC_A20_OEN */ |
| 0x1ac A_DELAY_PS(335) G_DELAY_PS(0) /* CFG_GPMC_A20_OUT */ |
| 0x1b4 A_DELAY_PS(468) G_DELAY_PS(0) /* CFG_GPMC_A21_OEN */ |
| 0x1b8 A_DELAY_PS(339) G_DELAY_PS(0) /* CFG_GPMC_A21_OUT */ |
| 0x1c0 A_DELAY_PS(676) G_DELAY_PS(0) /* CFG_GPMC_A22_OEN */ |
| 0x1c4 A_DELAY_PS(219) G_DELAY_PS(0) /* CFG_GPMC_A22_OUT */ |
| 0x1d0 A_DELAY_PS(1062) G_DELAY_PS(154) /* CFG_GPMC_A23_OUT */ |
| 0x1d8 A_DELAY_PS(640) G_DELAY_PS(0) /* CFG_GPMC_A24_OEN */ |
| 0x1dc A_DELAY_PS(150) G_DELAY_PS(0) /* CFG_GPMC_A24_OUT */ |
| 0x1e4 A_DELAY_PS(356) G_DELAY_PS(0) /* CFG_GPMC_A25_OEN */ |
| 0x1e8 A_DELAY_PS(150) G_DELAY_PS(0) /* CFG_GPMC_A25_OUT */ |
| 0x1f0 A_DELAY_PS(579) G_DELAY_PS(0) /* CFG_GPMC_A26_OEN */ |
| 0x1f4 A_DELAY_PS(200) G_DELAY_PS(0) /* CFG_GPMC_A26_OUT */ |
| 0x1fc A_DELAY_PS(435) G_DELAY_PS(0) /* CFG_GPMC_A27_OEN */ |
| 0x200 A_DELAY_PS(236) G_DELAY_PS(0) /* CFG_GPMC_A27_OUT */ |
| 0x364 A_DELAY_PS(759) G_DELAY_PS(0) /* CFG_GPMC_CS1_OEN */ |
| 0x368 A_DELAY_PS(372) G_DELAY_PS(0) /* CFG_GPMC_CS1_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC3_MANUAL1 in datamanual */ |
| mmc3_iodelay_manual1_conf: mmc3_iodelay_manual1_conf { |
| pinctrl-pin-array = < |
| 0x678 A_DELAY_PS(0) G_DELAY_PS(386) /* CFG_MMC3_CLK_IN */ |
| 0x680 A_DELAY_PS(605) G_DELAY_PS(0) /* CFG_MMC3_CLK_OUT */ |
| 0x684 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_CMD_IN */ |
| 0x688 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_CMD_OEN */ |
| 0x68c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_CMD_OUT */ |
| 0x690 A_DELAY_PS(171) G_DELAY_PS(0) /* CFG_MMC3_DAT0_IN */ |
| 0x694 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT0_OEN */ |
| 0x698 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT0_OUT */ |
| 0x69c A_DELAY_PS(221) G_DELAY_PS(0) /* CFG_MMC3_DAT1_IN */ |
| 0x6a0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT1_OEN */ |
| 0x6a4 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT1_OUT */ |
| 0x6a8 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_IN */ |
| 0x6ac A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_OEN */ |
| 0x6b0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_OUT */ |
| 0x6b4 A_DELAY_PS(474) G_DELAY_PS(0) /* CFG_MMC3_DAT3_IN */ |
| 0x6b8 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT3_OEN */ |
| 0x6bc A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT3_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC3_MANUAL2 in datamanual */ |
| mmc3_iodelay_sdr50_conf: mmc3_iodelay_sdr50_conf { |
| pinctrl-pin-array = < |
| 0x678 A_DELAY_PS(852) G_DELAY_PS(0) /* CFG_MMC3_CLK_IN */ |
| 0x680 A_DELAY_PS(94) G_DELAY_PS(0) /* CFG_MMC3_CLK_OUT */ |
| 0x684 A_DELAY_PS(122) G_DELAY_PS(0) /* CFG_MMC3_CMD_IN */ |
| 0x688 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_CMD_OEN */ |
| 0x68c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_CMD_OUT */ |
| 0x690 A_DELAY_PS(91) G_DELAY_PS(0) /* CFG_MMC3_DAT0_IN */ |
| 0x694 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT0_OEN */ |
| 0x698 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT0_OUT */ |
| 0x69c A_DELAY_PS(57) G_DELAY_PS(0) /* CFG_MMC3_DAT1_IN */ |
| 0x6a0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT1_OEN */ |
| 0x6a4 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT1_OUT */ |
| 0x6a8 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_IN */ |
| 0x6ac A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_OEN */ |
| 0x6b0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT2_OUT */ |
| 0x6b4 A_DELAY_PS(375) G_DELAY_PS(0) /* CFG_MMC3_DAT3_IN */ |
| 0x6b8 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT3_OEN */ |
| 0x6bc A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_MMC3_DAT3_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC4_MANUAL1 in datamanual */ |
| mmc4_iodelay_manual1_conf: mmc4_iodelay_manual1_conf { |
| pinctrl-pin-array = < |
| 0x840 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_CTSN_IN */ |
| 0x848 A_DELAY_PS(1147) G_DELAY_PS(0) /* CFG_UART1_CTSN_OUT */ |
| 0x84c A_DELAY_PS(1834) G_DELAY_PS(0) /* CFG_UART1_RTSN_IN */ |
| 0x850 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_RTSN_OEN */ |
| 0x854 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_RTSN_OUT */ |
| 0x870 A_DELAY_PS(2165) G_DELAY_PS(0) /* CFG_UART2_CTSN_IN */ |
| 0x874 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_CTSN_OEN */ |
| 0x878 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_CTSN_OUT */ |
| 0x87c A_DELAY_PS(1929) G_DELAY_PS(64) /* CFG_UART2_RTSN_IN */ |
| 0x880 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RTSN_OEN */ |
| 0x884 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RTSN_OUT */ |
| 0x888 A_DELAY_PS(1935) G_DELAY_PS(128) /* CFG_UART2_RXD_IN */ |
| 0x88c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RXD_OEN */ |
| 0x890 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RXD_OUT */ |
| 0x894 A_DELAY_PS(2172) G_DELAY_PS(44) /* CFG_UART2_TXD_IN */ |
| 0x898 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_TXD_OEN */ |
| 0x89c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_TXD_OUT */ |
| >; |
| }; |
| |
| /* Corresponds to MMC4_DS_MANUAL1 in datamanual */ |
| mmc4_iodelay_default_conf: mmc4_iodelay_default_conf { |
| pinctrl-pin-array = < |
| 0x840 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_CTSN_IN */ |
| 0x848 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_CTSN_OUT */ |
| 0x84c A_DELAY_PS(307) G_DELAY_PS(0) /* CFG_UART1_RTSN_IN */ |
| 0x850 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_RTSN_OEN */ |
| 0x854 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART1_RTSN_OUT */ |
| 0x870 A_DELAY_PS(785) G_DELAY_PS(0) /* CFG_UART2_CTSN_IN */ |
| 0x874 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_CTSN_OEN */ |
| 0x878 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_CTSN_OUT */ |
| 0x87c A_DELAY_PS(613) G_DELAY_PS(0) /* CFG_UART2_RTSN_IN */ |
| 0x880 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RTSN_OEN */ |
| 0x884 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RTSN_OUT */ |
| 0x888 A_DELAY_PS(683) G_DELAY_PS(0) /* CFG_UART2_RXD_IN */ |
| 0x88c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RXD_OEN */ |
| 0x890 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_RXD_OUT */ |
| 0x894 A_DELAY_PS(835) G_DELAY_PS(0) /* CFG_UART2_TXD_IN */ |
| 0x898 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_TXD_OEN */ |
| 0x89c A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_UART2_TXD_OUT */ |
| >; |
| }; |
| }; |
