| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung's S5PV210 based Galaxy Aries board device tree source |
| */ |
| |
| /dts-v1/; |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include "s5pv210.dtsi" |
| |
| / { |
| compatible = "samsung,aries", "samsung,s5pv210"; |
| |
| aliases: aliases { |
| i2c4 = &i2c_sound; |
| i2c5 = &i2c_accel; |
| i2c6 = &i2c_pmic; |
| i2c7 = &i2c_musb; |
| i2c9 = &i2c_fuel; |
| i2c10 = &i2c_touchkey; |
| i2c11 = &i2c_prox; |
| i2c12 = &i2c_magnetometer; |
| }; |
| |
| memory@30000000 { |
| device_type = "memory"; |
| reg = <0x30000000 0x05000000 |
| 0x40000000 0x10000000 |
| 0x50000000 0x08000000>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| mfc_left: region@43000000 { |
| compatible = "shared-dma-pool"; |
| no-map; |
| reg = <0x43000000 0x2000000>; |
| }; |
| |
| mfc_right: region@51000000 { |
| compatible = "shared-dma-pool"; |
| no-map; |
| reg = <0x51000000 0x2000000>; |
| }; |
| }; |
| |
| pmic_ap_clk: clock-0 { |
| /* Workaround for missing clock on PMIC */ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| |
| bt_codec: bt_sco { |
| compatible = "linux,bt-sco"; |
| #sound-dai-cells = <0>; |
| }; |
| |
| vibrator_pwr: regulator-fixed-0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vibrator-en"; |
| enable-active-high; |
| gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vibrator_ena>; |
| }; |
| |
| touchkey_vdd: regulator-fixed-1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VTOUCH_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| enable-active-high; |
| gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touchkey_vdd_ena>; |
| }; |
| |
| gp2a_vled: regulator-fixed-2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VLED"; |
| enable-active-high; |
| gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gp2a_power>; |
| }; |
| |
| wifi_pwrseq: wifi-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_gpio_rst>; |
| post-power-on-delay-ms = <500>; |
| power-off-delay-us = <500>; |
| }; |
| |
| i2c_sound: i2c-gpio-0 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sound_i2c_pins>; |
| |
| wm8994: wm8994@1a { |
| compatible = "wlf,wm8994"; |
| reg = <0x1a>; |
| |
| #sound-dai-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| clocks = <&clocks MOUT_CLKOUT>; |
| clock-names = "MCLK1"; |
| |
| AVDD2-supply = <&buck3_reg>; |
| DBVDD-supply = <&buck3_reg>; |
| CPVDD-supply = <&buck3_reg>; |
| SPKVDD1-supply = <&buck3_reg>; |
| SPKVDD2-supply = <&buck3_reg>; |
| |
| wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100 |
| 0xa101 0x0100 0x8100 0x0100 0x0100 |
| 0x0100>; |
| |
| wlf,ldo1ena = <&gpf3 4 GPIO_ACTIVE_HIGH>; |
| wlf,ldo2ena = <&gpf3 4 GPIO_ACTIVE_HIGH>; |
| |
| wlf,lineout1-se; |
| wlf,lineout2-se; |
| |
| assigned-clocks = <&clocks MOUT_CLKOUT>; |
| assigned-clock-rates = <0>; |
| assigned-clock-parents = <&xusbxti>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&codec_ldo>; |
| }; |
| }; |
| |
| i2c_accel: i2c-gpio-1 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_i2c_pins>; |
| |
| accelerometer@38 { |
| compatible = "bosch,bma023"; |
| reg = <0x38>; |
| |
| vdd-supply = <&ldo9_reg>; |
| vddio-supply = <&ldo9_reg>; |
| }; |
| }; |
| |
| i2c_pmic: i2c-gpio-2 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_i2c_pins>; |
| |
| pmic@66 { |
| compatible = "maxim,max8998"; |
| reg = <0x66>; |
| interrupt-parent = <&gph0>; |
| interrupts = <7 IRQ_TYPE_EDGE_FALLING>; |
| |
| max8998,pmic-buck1-default-dvs-idx = <1>; |
| max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>, |
| <&gph0 4 GPIO_ACTIVE_HIGH>; |
| max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>, |
| <1050000>, <950000>; |
| |
| max8998,pmic-buck2-default-dvs-idx = <0>; |
| max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>; |
| max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_dvs_pins &pmic_irq>; |
| |
| regulators { |
| ldo2_reg: LDO2 { |
| regulator-name = "VALIVE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "VUSB_1.1V"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "VADC_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo5_reg: LDO5 { |
| regulator-name = "VTF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "LDO6"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <3600000>; |
| }; |
| |
| ldo7_reg: LDO7 { |
| regulator-name = "VLCD_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo8_reg: LDO8 { |
| regulator-name = "VUSB_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo9_reg: LDO9 { |
| regulator-name = "VCC_2.8V_PDA"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-always-on; |
| }; |
| |
| ldo10_reg: LDO10 { |
| regulator-name = "VPLL_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo11_reg: LDO11 { |
| regulator-name = "CAM_AF_3.0V"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo12_reg: LDO12 { |
| regulator-name = "CAM_SENSOR_CORE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo13_reg: LDO13 { |
| regulator-name = "VGA_VDDIO_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo14_reg: LDO14 { |
| regulator-name = "VGA_DVDD_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo15_reg: LDO15 { |
| regulator-name = "CAM_ISP_HOST_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo16_reg: LDO16 { |
| regulator-name = "VGA_AVDD_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo17_reg: LDO17 { |
| regulator-name = "VCC_3.0V_LCD"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| buck1_reg: BUCK1 { |
| regulator-name = "vddarm"; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1500000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <1250000>; |
| }; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "vddint"; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1500000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <1100000>; |
| }; |
| }; |
| |
| buck3_reg: BUCK3 { |
| regulator-name = "VCC_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| buck4_reg: BUCK4 { |
| regulator-name = "CAM_ISP_CORE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ap32khz_reg: EN32KHz-AP { |
| regulator-name = "32KHz AP"; |
| regulator-always-on; |
| }; |
| |
| cp32khz_reg: EN32KHz-CP { |
| regulator-name = "32KHz CP"; |
| }; |
| |
| vichg_reg: ENVICHG { |
| regulator-name = "VICHG"; |
| regulator-always-on; |
| }; |
| |
| safe1_sreg: ESAFEOUT1 { |
| regulator-name = "SAFEOUT1"; |
| }; |
| |
| safe2_sreg: ESAFEOUT2 { |
| regulator-name = "SAFEOUT2"; |
| }; |
| }; |
| }; |
| }; |
| |
| i2c_musb: i2c-gpio-3 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&musb_i2c_pins>; |
| |
| fsa9480: musb@25 { |
| compatible = "fcs,fsa9480"; |
| reg = <0x25>; |
| interrupt-parent = <&gph2>; |
| interrupts = <7 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&musb_irq>; |
| }; |
| }; |
| |
| i2c_fuel: i2c-gpio-4 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fg_i2c_pins>; |
| |
| fg: fuelgauge@36 { |
| compatible = "maxim,max17040"; |
| reg = <0x36>; |
| }; |
| }; |
| |
| i2c_touchkey: i2c-gpio-5 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touchkey_i2c_pins>; |
| |
| touchkey@20 { |
| compatible = "cypress,aries-touchkey"; |
| reg = <0x20>; |
| vdd-supply = <&touchkey_vdd>; |
| vcc-supply = <&buck3_reg>; |
| linux,keycodes = <KEY_MENU KEY_BACK |
| KEY_HOMEPAGE KEY_SEARCH>; |
| interrupt-parent = <&gpj4>; |
| interrupts = <1 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touchkey_irq>; |
| }; |
| }; |
| |
| i2c_prox: i2c-gpio-6 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&prox_i2c_pins>; |
| |
| light-sensor@44 { |
| compatible = "sharp,gp2ap002a00f"; |
| reg = <0x44>; |
| interrupt-parent = <&gph0>; |
| interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&gp2a_vled>; |
| vio-supply = <&gp2a_vled>; |
| io-channels = <&gp2a_shunt>; |
| io-channel-names = "alsout"; |
| sharp,proximity-far-hysteresis = /bits/ 8 <0x40>; |
| sharp,proximity-close-hysteresis = /bits/ 8 <0x20>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gp2a_irq>; |
| }; |
| }; |
| |
| i2c_magnetometer: i2c-gpio-7 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&magnetometer_i2c_pins>; |
| |
| status = "disabled"; |
| |
| /* Yamaha yas529 magnetometer, no mainline binding */ |
| }; |
| |
| vibrator: pwm-vibrator { |
| compatible = "pwm-vibrator"; |
| pwms = <&pwm 1 44642 0>; |
| pwm-names = "enable"; |
| vcc-supply = <&vibrator_pwr>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm1_out>; |
| }; |
| |
| poweroff: syscon-poweroff { |
| compatible = "syscon-poweroff"; |
| regmap = <&pmu_syscon>; |
| offset = <0x681c>; /* PS_HOLD_CONTROL */ |
| value = <0x5200>; |
| }; |
| |
| spi_lcd: spi-2 { |
| compatible = "spi-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>; |
| mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>; |
| cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>; |
| num-chipselects = <1>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_spi_pins>; |
| |
| panel@0 { |
| compatible = "samsung,s6e63m0"; |
| reg = <0>; |
| reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>; |
| vdd3-supply = <&ldo7_reg>; |
| vci-supply = <&ldo17_reg>; |
| spi-cs-high; |
| spi-max-frequency = <1200000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_rst>; |
| |
| port { |
| lcd_ep: endpoint { |
| remote-endpoint = <&fimd_ep>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &adc { |
| vdd-supply = <&ldo4_reg>; |
| |
| status = "okay"; |
| |
| gp2a_shunt: current-sense-shunt { |
| compatible = "current-sense-shunt"; |
| io-channels = <&adc 9>; |
| shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */ |
| #io-channel-cells = <0>; |
| io-channel-ranges; |
| }; |
| }; |
| |
| &fimd { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_clk &lcd_data24>; |
| status = "okay"; |
| |
| samsung,invert-vden; |
| samsung,invert-vclk; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@3 { |
| reg = <3>; |
| fimd_ep: endpoint { |
| remote-endpoint = <&lcd_ep>; |
| }; |
| }; |
| }; |
| |
| &hsotg { |
| vusb_a-supply = <&ldo8_reg>; |
| vusb_d-supply = <&ldo3_reg>; |
| dr_mode = "peripheral"; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-max-bus-freq = <400000>; |
| samsung,i2c-slave-addr = <0x10>; |
| status = "okay"; |
| |
| touchscreen@4a { |
| compatible = "atmel,maxtouch"; |
| reg = <0x4a>; |
| interrupt-parent = <&gpj0>; |
| interrupts = <5 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_irq>; |
| reset-gpios = <&gpj1 3 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &i2s0 { |
| dmas = <&pdma0 9>, <&pdma0 10>, <&pdma0 11>; |
| status = "okay"; |
| }; |
| |
| &mfc { |
| memory-region = <&mfc_left>, <&mfc_right>; |
| }; |
| |
| &pinctrl0 { |
| bt_reset: bt-reset { |
| samsung,pins = "gpb-3"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| wlan_bt_en: wlan-bt-en { |
| samsung,pins = "gpb-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-val = <1>; |
| }; |
| |
| codec_ldo: codec-ldo { |
| samsung,pins = "gpf3-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| }; |
| |
| prox_i2c_pins: gp2a-i2c-pins { |
| samsung,pins = "gpg0-2", "gpg2-2"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| wlan_gpio_rst: wlan-gpio-rst { |
| samsung,pins = "gpg1-2"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| }; |
| |
| bt_wake: bt-wake { |
| samsung,pins = "gpg3-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| }; |
| |
| gp2a_irq: gp2a-irq { |
| samsung,pins = "gph0-2"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| pmic_dvs_pins: pmic-dvs-pins { |
| samsung,pins = "gph0-3", "gph0-4", "gph0-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| samsung,pin-val = <0>; |
| }; |
| |
| pmic_irq: pmic-irq { |
| samsung,pins = "gph0-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| wifi_host_wake: wifi-host-wake { |
| samsung,pins = "gph2-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| bt_host_wake: bt-host-wake { |
| samsung,pins = "gph2-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| musb_irq: musq-irq { |
| samsung,pins = "gph2-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| tf_detect: tf-detect { |
| samsung,pins = "gph3-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| wifi_wake: wifi-wake { |
| samsung,pins = "gph3-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| }; |
| |
| magnetometer_i2c_pins: yas529-i2c-pins { |
| samsung,pins = "gpj0-0", "gpj0-1"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| ts_irq: ts-irq { |
| samsung,pins = "gpj0-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| vibrator_ena: vibrator-ena { |
| samsung,pins = "gpj1-1"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| gp2a_power: gp2a-power { |
| samsung,pins = "gpj1-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| touchkey_i2c_pins: touchkey-i2c-pins { |
| samsung,pins = "gpj3-0", "gpj3-1"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| touchkey_vdd_ena: touchkey-vdd-ena { |
| samsung,pins = "gpj3-2"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| musb_i2c_pins: musb-i2c-pins { |
| samsung,pins = "gpj3-4", "gpj3-5"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| accel_i2c_pins: accel-i2c-pins { |
| samsung,pins = "gpj3-6", "gpj3-7"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| pmic_i2c_pins: pmic-i2c-pins { |
| samsung,pins = "gpj4-0", "gpj4-3"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| touchkey_irq: touchkey-irq { |
| samsung,pins = "gpj4-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_UP>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| lcd_spi_pins: spi-lcd-pins { |
| samsung,pins = "mp01-1", "mp04-1", "mp04-3"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| fg_i2c_pins: fg-i2c-pins { |
| samsung,pins = "mp05-0", "mp05-1"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| sound_i2c_pins: sound-i2c-pins { |
| samsung,pins = "mp05-2", "mp05-3"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| panel_rst: panel-rst { |
| samsung,pins = "mp05-5"; |
| samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| }; |
| |
| &pwm { |
| samsung,pwm-outputs = <1>; |
| }; |
| |
| &rtc { |
| clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>; |
| clock-names = "rtc", "rtc_src"; |
| }; |
| |
| &sdhci1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bus-width = <4>; |
| max-frequency = <38400000>; |
| pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>; |
| pinctrl-names = "default"; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| keep-power-in-suspend; |
| |
| mmc-pwrseq = <&wifi_pwrseq>; |
| non-removable; |
| status = "okay"; |
| |
| assigned-clocks = <&clocks MOUT_MMC1>, <&clocks SCLK_MMC1>; |
| assigned-clock-rates = <0>, <50000000>; |
| assigned-clock-parents = <&clocks MOUT_MPLL>; |
| |
| wlan@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| interrupt-parent = <&gph2>; |
| interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &sdhci2 { |
| bus-width = <4>; |
| cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <&ldo5_reg>; |
| pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| assigned-clocks = <&clocks MOUT_MMC2>, <&clocks SCLK_MMC2>; |
| assigned-clock-rates = <0>, <50000000>; |
| assigned-clock-parents = <&clocks MOUT_MPLL>; |
| }; |
| |
| &uart0 { |
| assigned-clocks = <&clocks MOUT_UART0>, <&clocks SCLK_UART0>; |
| assigned-clock-rates = <0>, <111166667>; |
| assigned-clock-parents = <&clocks MOUT_MPLL>; |
| |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4329-bt"; |
| max-speed = <3000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake |
| &bt_reset &bt_wake>; |
| shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>; |
| interrupt-parent = <&gph2>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &usbphy { |
| status = "okay"; |
| vbus-supply = <&safe1_sreg>; |
| }; |
| |
| &xusbxti { |
| clock-frequency = <24000000>; |
| }; |
